How it Works
Trotec
Loading...
DH 15
Original Instructions Manual
23 pgs3.29 Mb0
Table of contents
Loading...

Trotec DH 15, DH 30, DH 60 Original Instructions Manual

Download
DH 15 / DH 30 / DH 60
EN
ORIGINAL INSTRUCTIONS
DEHUMIDIFIER
TRT-BA-DH15-DH30-DH60-TC2019-22-005-EN

Table of contents

You can download the current version of the instructions and the EUdeclaration of conformity via the following link:

Notes regarding the instructions

Symbols

Warning of electrical voltage
This symbol indicates dangers to the life and health of persons due to electrical voltage.
DH 15
https://hub.trotec.com/?id=42978
DH 30
https://hub.trotec.com/?id=42979
DH 60
https://hub.trotec.com/?id=42980

Safety

Warning
This signal word indicates a hazard with an average risk level which, if not avoided, can result in serious injury or death.
Caution
This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury.
Note
This signal word indicates important information (e.g. material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the instructions must be observed.
Read this manual carefully before starting or using the device. Always store the manual in the immediate vicinity of the device or its site of use!
Warning Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future reference.
This appliance can be used by children aged from 8years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Let the device dry out after a wet clean. Do not operate it when wet.
• Do not use the device with wet or damp hands.
2 EN
dehumidifier DH 15 / DH 30 / DH 60
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover or transport the device during operation.
• Do not sit on the device.
• This appliance is not a toy! Keep away from children and animals. Do not leave the device unattended during operation.
• Check accessories and connection parts for possible damage prior to every use of the device. Do not use any defective devices or device parts.
• Ensure that all electric cables outside of the device are protected from damage (e.g. caused by animals). Never use the device if electric cables or the power connection are damaged!
• The electrical connection must correspond to the specifications in chapter Technical data.
• Insert the mains plug into a properly secured mains socket.
• Observe the device's power input, cable length and intended use when selecting extensions to the power cable. Completely unroll extension cables. Avoid electrical overload.
• Before carrying out maintenance, care or repair work on the device, remove the mains plug from the mains socket. Hold onto the mains plug while doing so.
• Disconnect the power cable from the mains socket when the device is not in use.
• Do not under any circumstances use the device if you detect damages on the mains plug or power cable. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Defective power cables pose a serious health risk!
• Observe the storage and operating conditions as given in the Technical data chapter.
• Make sure that the air inlet and outlet are not obstructed.
• Make sure that the suction side is kept free of dirt and loose objects.
• Do not remove any safety signs, stickers or labels from the device. Keep all safety signs, stickers and labels in legible condition.
• Only transport the device in an upright position with an emptied condensation tank or drain hose.
• Discharge the collected condensate before transport and storage. Do not drink it. Health hazard!

Intended use

Only use the device as a stationary industrial dryer for drying and dehumidifying room air whilst adhering to the technical data and safety instructions.
Intended use comprises:
• drying and dehumidifying: – production plants, underground rooms
– store rooms, archives, laboratories – rooms and areas after water damage caused by burst
pipes or flooding
• keeping dry of: – instruments, devices, files
– electrical control centres – moisture-sensitive goods, loads, etc.

Improper use

• Do not place the device on wet or flooded ground.
• Do not place any objects, e.g. clothing, on the device.
• Do not use the device outdoors.
• Any unauthorised modifications, alterations or structural
changes to the device are forbidden.
• Any operation other than as described in this manual is
prohibited. Non-observance renders all claims for liability and guarantee null and void.

Personnel qualifications

People who use this device must:
• be aware of the dangers that occur when working with
electric devices in damp areas.
• have read and understood the instructions, especially the
Safety chapter.
Maintenance tasks which require the housing to be opened must only be carried out by specialist companies for cooling and air-conditioning or by Trotec.
EN 3
dehumidifier DH 15 / DH 30 / DH 60

Residual risks

Warning of electrical voltage
Work on the electrical components must only be carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug from the mains socket! Hold onto the mains plug while pulling the power cable out of the mains socket.
Warning
Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way! Observe the personnel qualifications!
Warning A falling device can cause injuries! Always transport
and assemble the device with the help of other persons. Never stand below the device when it is
suspended. Ensure adequate stability of the device's wall fixing.
Warning
The device is not a toy and does not belong in the hands of children.
Warning
Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy.

Behaviour in the event of an emergency

1. In an emergency, disconnect the device from the mains feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket.
2. Do not reconnect a defective device to the mains.

Information about the device

Description of the device

The dehumidifiers of the DH series uses the principle of condensation to automatically dehumidify rooms.
The fan sucks damp room air through the air inlet, the evaporator and the condenser located behind it. The air is cooled at the cold evaporator until it is below the dew point. Water vapour contained in the room air precipitates on the evaporator fins as condensation or rime. The dehumidified, cooled air is rewarmed at the condenser and blown out at a temperature of approx. 5°C above room temperature.
The drier air, thus conditioned, mixes with the air in the room via the air outlet. The humidity in the room where the device is positioned is reduced as air constantly circulates through the device. Depending on the air temperature and the relative humidity, the condensed water either drops continuously or only during the defrost phase through the pre-assembled condensation drain hose and is discharged from the device.
To set the desired humidity level, a hygrostat with control dial is provided in the device's interior. This control dial can be easily accessed once the housing has been removed.
The device can reduce the relative humidity of a room to approx. 30%.
Because of the heat radiation generated during operation, the room temperature may rise slightly.
A high humidity level in the air (starting at 70%RH) provides the perfect breeding ground for mould. However, the room air must not be too dry either (<40%RH). Materials such as leather or rubber become porous, and wood becomes brittle and fissured.
4 EN
dehumidifier DH 15 / DH 30 / DH 60

Device depiction

1
1
2
3
6
4
5, 8
3
1
2
6
7
3
4
5, 8
DH15
DH30/ DH60
No. Designation
1 Air outlet 2 Housing 3 Air inlet 4 Hose connector for condensation drain hose
(inside the device)
5 Control dial hygrostat
(tamper-proof installation inside the device) 6 Wall holder 7 Suspension 8 MODEswitch

Transport and storage

Note
If you store or transport the device improperly, the device may be damaged. Note the information regarding transport and storage of the device.

Transport

Always utilize the help of another person to transport the DH15/ DH30. Always utilize the help of two other persons to transport the DH60. Do not try to transport the device without the help of another person. To lift the device, use a forklift or an elevating truck as appropriate.
Before transporting the device, observe the following:
• Hold onto the mains plug while pulling the power cable out of the mains socket.
• Do not use the power cable to drag the device.
• Drain the remaining condensate from the device.
After transporting the device, observe the following:
• Set up the device in an upright position after transport.
• After having transported the device in horizontal position, leave the device to rest for 12to24hours, so the refrigerant can accumulate within the compressor. Wait 12to24hours before switching the device back on! Acting contrary might lead to compressor damage and a malfunctioning device. Any warranty claims will be voided in this case.
EN 5
dehumidifier DH 15 / DH 30 / DH 60

Storage

C
C
A
B
D
I. III.II.
Before storing the device, proceed as follows:
• Drain the remaining condensate from the device.
• Hold onto the mains plug while pulling the power cable out of the mains socket.
When the device is not being used, observe the following storage conditions:
• dry and protected from frost and heat
• in an upright position where it is protected from dust and direct sunlight
• with a cover to protect it from invasive dust, if necessary
• Place no further devices or objects on top of the device to prevent it from being damaged.

Assembly and installation

Scope of delivery

• 1x Device
• 1x Wall holder
• 1x Condensation drain hose, 10mm diameter
• 1x Manual

Unpacking the device

1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power cable is not damaged and that you do not damage it during unwinding.
• When assembling the device, observe the minimum distance from adjacent walls or other objects as described in the Technical Data chapter.
Assemble the device as follows: Select screw and wall plug sizes suitable for the weight of the
device (see technical data) and the structure of the wall.
DH15
1. Mark the position for the bore holes.
2. Drill the holes into the wall.
3. Insert suitable wall plugs into the drill holes.

Assembly

Always utilize the help of another person to assemble the DH15/ DH30. Always utilize the help of two other persons to assemble the DH60. Do not try to assemble the device without the help of another person. To lift the device, use a forklift or an elevating truck as appropriate.
Observe the following instructions:
• When assembling the device, keep a sufficient distance to heat sources.
• When assembling the device, especially in wet areas, secure the device locally with an RCD (Residual Current protective Device) which complies with the relevant regulations.
• Make sure that extension cables are unrolled completely.
• Insert the mains plug into a properly secured mains socket.
6 EN
dehumidifier DH 15 / DH 30 / DH 60
4. Remove the housing.
5
Ø = 11 mm
5. Screw the support rail and the device to the wall.
7. Check whether the condensation drain hose is positioned correctly. The condensation drain hose must not be kinked.
8. Put the housing back on the device.
6. Set the control dial(5) to the desired humidity level.
EN 7
dehumidifier DH 15 / DH 30 / DH 60
DH30/ DH60
5
1. Mark the position for the bore holes.
2. Drill the holes into the wall.
6. Remove the housing.
7. Set the control dial(5) to the desired humidity level.
3. Insert suitable wall plugs into the drill holes.
4. Screw the support rail to the wall.
5. Suspend the device from the wall holder by means of the mounting brackets. Utilize the help of one or two other persons as well as suitable lifting gear to do so.
8 EN
dehumidifier DH 15 / DH 30 / DH 60
8. Check whether the condensation drain hose is positioned
Ø = 11 mm
5
8
correctly. The condensation drain hose must not be kinked.
9. Put the housing back on the device.

Operation

• After being switched on, the device operates fully automatically.
• To ensure that the built-in sensor can correctly detect the humidity, the fan continues to operate until the device is switched off.
• Avoid open doors and windows.
Operating elements
No. Designation Meaning
5 Control dial For setting the desired humidity level 8 MODEswitch For setting the desired operating mode:
CONT. = fan runs permanently. CYC. = fan switches on and off along
with the compressor.
EN 9
dehumidifier DH 15 / DH 30 / DH 60
Positioning the condensation drain hose
Note: The condensation drain hose is already installed when the device is delivered.
1. Ensure that the condensation drain hose is properly connected to the device and is free of damage.
2. Depending on the application, position the end of the condensation drain hose as follows:
ð Place a sufficiently dimensioned container (at least
20litres) beside the device and insert the hose end. Check the filling level of the container regularly.
ð Position the end of the condensation drain hose near a
water drain. For larger distances, a longer hose of the same type can also be used.
3. Regularly check the condensation drain hose for obstructions or kinks.
External condensate pump (optional)
The device can optionally be operated with an external condensate pump.
It can be obtained from Trotec as article number
6.100.000.019.
Switching the device on
1. Ensure that the condensation drain hose has been laid and connected properly. Do not create tripping hazards.
2. Ensure that the condensation drain hose is not bent or jammed and that there are no objects on the condensation drain hose.
3. Ensure that the condensation can run off properly.
4. Insert the mains plug into a properly secured mains socket.
10 EN
dehumidifier DH 15 / DH 30 / DH 60
Regulating the room humidity level
5
Set the desired humidity level via the control dial(5) of the hygrostat.
Automatic defrost
If the room temperature is lower than 15°C, the heat exchanger will freeze during dehumidification. The device will then carry out an automatic defrost. The duration of the defrost process can vary depending on the room temperature. The lower the temperatures, the longer the defrost period.
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Hold onto the mains plug while pulling the power cable out of the mains socket.
• Remove the residual fluid from the condensation drain hose.
• Clean the device according to the Maintenance chapter.
• Store the device according to the Storage chapter.

Errors and faults

The device has been checked for proper functioning several times during production. If malfunctions occur nonetheless, check the device according to the following list.
The device does not start:
• Check the power connection.
• Check the power cable for damages.
• Check the on-site fusing.
• Check the preselected humidity level at the hygrostat's control dial. The humidity in the room must be above the selected range. Reduce the preselected desired humidity level.
• Have the electrics checked by a specialist company for cooling and air-conditioning or by Trotec.
The device is running, but there is no formation of condensate:
• Check whether the condensation drain hose is positioned correctly.
• Check the room temperature. Observe the device's permissible operating range according to the technical data.
• Ensure that the relative humidity complies with the technical data.
• Check the preselected humidity level at the hygrostat's control dial. The humidity in the room must be above the selected range. Reduce the preselected desired humidity level.
The device is loud or vibrates:
• Check whether the device is mounted horizontally.
• Check the inside of the device for dirt. Clean the interior of the device if necessary.
The device gets very warm, is loud or loses power:
• Check the air inlets for dirt. Remove external dirt.
• Check the inside of the device for dirt. Clean the interior of the device if necessary.
Your device still does not operate correctly after these checks?
Please contact the customer service. If necessary, bring the device to a specialist company for cooling and air-conditioning or to Trotec for repair.
EN 11
dehumidifier DH 15 / DH 30 / DH 60

Maintenance

Maintenance intervals

Maintenance and care interval before every
start-up
Check air inlets and outlets for dirt
X X
and foreign objects and clean ifnecessary
Clean the exterior Visually check the inside of the
device for dirt Check for damage
X X
Check the attachment screws Test run Empty the optional condensate
pump, condensation tray and/or condenser dryer

Maintenance and care log

Device type: .............................................
Maintenance and care interval
Check air inlets and outlets for dirt and foreign objects and clean if necessary
Clean the exterior Visually check the inside of the
device for dirt Check for damage Check the attachment screws Check the optional condensate
pump and tank, and clean if necessary
Test run Comments
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
as needed at least every
2weeks
X X
X X
X X
X
at least every 4weeks
at least every 6months
Device number: ....................................
at least annually
X
1. Date: ...................................
Signature: ................................
5. Date: ...................................
Signature: ................................
9. Date: ...................................
Signature: ................................
13. Date: .................................
Signature: ................................
12 EN
2. Date: ....................................
Signature: .................................
6. Date: ....................................
Signature: .................................
10. Date: ..................................
Signature: .................................
14. Date: ..................................
Signature: .................................
dehumidifier DH 15 / DH 30 / DH 60
3. Date: ....................................
Signature: .................................
7. Date: ....................................
Signature: .................................
11. Date: ..................................
Signature: .................................
15. Date: ..................................
Signature: .................................
4. Date: ....................................
Signature: .................................
8. Date: ....................................
Signature: .................................
12. Date: ..................................
Signature: .................................
16. Date: ..................................
Signature: .................................

Activities required before starting maintenance

Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Hold onto the mains plug while pulling the power cable out of the mains socket.
Warning of electrical voltage
Maintenance tasks at the electrical equipment or the air-conditioning technology must only be carried out by specialist companies for cooling and air-conditioning or by Trotec.

Cleaning the housing

Clean the housing with a soft, damp and lint-free cloth. Ensure that no moisture enters the housing. Protect electrical components from moisture. Do not use any aggressive cleaning agents such as cleaning sprays, solvents, alcohol-based or abrasive cleaners to dampen the cloth.
2. Remove heavy soiling on the inside of the device. If necessary, clean the interior of the device using compressed air or lukewarm soapsuds.
3. Put the housing back on the device.
ð DH15

Cleaning the inside of the device

Perform this activity at least once a year.
1. Remove the housing.
ð DH15
ð DH30/ DH60
ð DH30/ DH60

Refrigerant circuit

• The entire refrigerant circuit is a maintenance-free, hermetically sealed system and may only be maintained or repaired by specialist companies for cooling and air-conditioning or by Trotec.
EN 13
dehumidifier DH 15 / DH 30 / DH 60

Technical annex

Technical data

Parameter DH 15 DH 30 DH 60
Dehumidification performance see dehumidification diagrams Power supply 1/N/PE~ 230V/ 50Hz 1/N/PE~ 230V/ 50Hz 1/N/PE~ 230V/ 50Hz Power cable CEE7/7/ l= 3.5m CEE7/7/ l= 3.5m CEE7/7/ l= 3.5m Power input 0.43kW 0.75kW 1.2kW Nominal/peak current 3.8A/ 18A 4.4A/ 15.8A 7.5A/ 30A Heat emission 0.9kW 1.9kW 3.5kW Coefficient of performance 1.6 2.5 2.9 Refrigerant R-407C R-407C R-407C GWP factor 1,774 1,774 1,774 CO2 equivalent 0.603t 0.887t 1.419t Amount of refrigerant 340g 500g 800g Air volume (freely blowing) 225m³/h 700m³/h 1,280m³/h Sound pressure level @3m 49dB(A) 52dB(A) 54dB(A) Operating range temperature 0to 40°C 0to 40°C 0to 40°C Setting range relative humidity 30% to 60%RH Max. permissible relative humidity 90%RH Weight 37.1kg 46.8kg 70kg Dimensions (lengthx widthx height)
365x 840x 330mm 255x 790x 651mm 255x 1253x 651mm
incl. wall holder Minimum distance to walls or other objects:
A: top:
B: bottom:
C: side:
D: front:
12.5cm
12.5cm
12.5cm
12.5cm
12.5cm
12.5cm
12.5cm
12.5cm
12.5cm
12.5cm
12.5cm
12.5cm
14 EN
dehumidifier DH 15 / DH 30 / DH 60
Dehumidification charts
l / 24 h
35
30
25
20
15
10
°C
1) 2)
DH 15
40 % 50% 60% 70 %
80 %
0 5 10 15 20 25 30
1,0
0,9
0,8
0,7
0,6
0,5
0,60
0,55
0,50
0,45
0,40
0,35
35
30
25
20
15
10
°C
l / 24 h
1) 2)
DH 30
0 10 20 30 40 50 60
2,15
1,90
1,70
1,50
1,35
1,20
0,80
0,75
0,70
0,65
0,60
0,55
40 %30 % 50% 60% 70 %
80 %
35
30
25
20
15
10
°C
l / 24 h
1) 2)
DH 60
0 20 40 60 80 100 120
4,1
3,5
3,1
2,6
2,3
1,9
1,3
1,2
1,1
1,0
0,9
0,8
40 %30 % 50% 60 % 70 %
80 %
COMPRESSOR
SOLENOID VALVE
AIR CONDENSER
EVAPORATOR
DRIER
CAPILLARY
INSULATION
PROCESS PORT
Refrigerant circuit diagram
1) Heat emission in kW at 60%RH
2) Power input in kW at 60%RH
EN 15
dehumidifier DH 15 / DH 30 / DH 60
Wiring diagram DH15
Wiring diagram DH30/ DH60
16 EN
dehumidifier DH 15 / DH 30 / DH 60
Exploded assembly drawing DH15 Info
32
33
31
The position numbers of the spare parts differ from those describing the positions of the components mentioned in these instructions.
NO. SPARE PART QTY. NO. SPARE PART QTY.
1 Structural Back 1 18 Isulation EPS 1 2 Structural cover back 2 19 Water Pan 1 3 Ventilation duct 1 20 Tank Warning Lamp 1 4 Base Plate 1 21 Racord 3/8"G 1 5 Wall Support 1 22 Remote humidistat socket 1 6 Electrical control cover 1 23 Nut 3/8"G 1 7 Compressor 1 24 Heat exchanger Kit 1 8 Cable gland 1 25 Placa Espuma 255x45x25 2 9 Electronic Controller 1 26 Cover insert Ø22 1 10 Defrost Sensor 1 27 O´Ring TPE Ø25 x Ø14 x 2.5 1 11 Terminal strip 5W 1 28 PCB spacer 4 12 Fan motor Ø250 (complete assembly) 1 29 Cable tie mounts 12 13 Defrost valve 1 30 Speed nut 1 14 Defrost valve coil 1 31 Basic device 1 15 Hygrostat 1 32 Screw (DIN7380 - M4x10)
5
with washer (DIN125 - AØ4,3) 16 High pressure switch 1 33 Housing Z-EK-DH15 1 17 Low pressure switch 1
EN 17
dehumidifier DH 15 / DH 30 / DH 60
Exploded assembly drawing DH30 Info
43
44
45
45
46
47
48
The position numbers of the spare parts differ from those describing the positions of the components mentioned in these instructions.
18 EN
dehumidifier DH 15 / DH 30 / DH 60
NO. SPARE PART QTY. NO. SPARE PART QTY.
1 Structural Back 1 25 Humidistat venting hose 1 2 Condensing coil base plate 1 26 Water pan 1 3 Right side panel 1 27 Nut for hose fitting 1 4 Left side panel 1 28 Sealing washer 1 5 Compressor base plate 1 29 Hose 1 6 Control´s cover 1 30 Hose 1 7 Dashboard 1 31 Evaporating coil 1 8 Botton housing profile 1 32 Drops tray 1 9 Compressor cover 1 33 Edge profile 2 10 Condensing coil insulating profile 1 34 Defrost valve coil 1 11 Wall bracket 1 35 Defrost valve 1 12 Compressor 1 36 Cable tie mount 8 13 Condensing coil 1 37 Absorver feet 2 14 Fan 1 38 Insulation foam 1 15 Low pressure switch 1 39 Acoustic insulation foam 1 16 High pressure switch 1 40 Cable Gland 1 17 Humidistat 1 41 Power supply cover 1 18 Humidistat knob 1 42 Copper tube bracket 2 19 Fan mode switch 1 43 Basic device 1 20 Cable clamp 1 44 Screw (DIN 7985 - M4x8)
2 with washer (detent-edged washer SKK4 Ø4,3xØ8,2x1,2)
21 Pipe clip 1 45 Insulation 2 22 Terminal strip 1 46 self-adhesive sealing tape (B/H=50/3mm L=785mm) 5 23 Electronic controller 1 47 self-adhesive sealing tape (B/H=9/6mm L=785mm) 1 24 PCB spacer 4 48 Housing SBG-01954-01 1
EN 19
dehumidifier DH 15 / DH 30 / DH 60
Exploded assembly drawing DH60 Info
44
45
46
46
47
48 49
The position numbers of the spare parts differ from those describing the positions of the components mentioned in these instructions.
20 EN
dehumidifier DH 15 / DH 30 / DH 60
NO. SPARE PART QTY. NO. SPARE PART QTY.
1 Structural Back 1 26 Water pan 1 2 Condensing coil base plate 1 27 Nut for hose fitting 1 3 Right side panel 1 28 Sealing washer 1 4 Left side panel 1 29 Hose 1 5 Compressor base plate 1 30 Hose 5/8" 1 6 Control cover 1 31 Evaporator coil 1 7 Dashboard 1 32 Drops tray 1 8 Botton housing profile 1 33 Edge profile 2 9 Compressor cover 1 34 Defrost valve coil 1 10 Condensing coil insulating profile 1 35 Defrost valve 1 11 Wall bracket 1 36 Cable tie mount 12 12 Compressor 1 37 Absorver feet 2 13 Condensator coil 1 38 Insulation foam 1 14 Fan 1 39 Acoustic insulation foam 1 15 Low pressure switch 1 40 Cable Gland 1 16 High pressure switch 1 41 Power supply cover 1 17 Humidistat 1 42 Copper tube bracket 4 18 Humidistat knob 1 43 Compressor strength support 1 19 Fan mode switch 1 44 Basic device 1 20 Cable clamp 1 45 Screw (DIN 7985 - M4x10)
3 with washer (detent-edged washer Ø4,3xØ8,2x1,2)
21 Pipe clip 1 46 Insulation 2 22 Terminal strip 1 47 self-adhesive sealing tape (B/H=9/6mm L=1250mm) 1 23 Electronic controller 1 48 self-adhesive sealing tape (B/H=50/3mm) 5 24 PCB spacer 4 49 Housing SBG-01953-01 1 25 Humidistat venting hose 1
EN 21
dehumidifier DH 15 / DH 30 / DH 60

Disposal

The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment must not be disposed of with the household waste at the end of its life. You will find collection points for free return of waste electrical and electronic equipment in your vicinity. The addresses can be obtained from your municipality or local administration. For further return options provided by us please refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic equipment aims to enable the re-use, recycling and other forms of recovery of waste equipment as well as to prevent negative effects for the environment and human health caused by the disposal of hazardous substances potentially contained in the equipment.
The device is operated with fluorinated greenhouse gas which can be dangerous for the environment and contribute to global warming when emitted to the atmosphere.
Further information is provided on the nameplate. Dispose of the refrigerant appropriately and according to the
national regulations.

Declaration of conformity

The text below sets out the contents of the declaration of conformity. The signed declaration of conformity can be found at https://hub.trotec.com/?id=42978.
Declaration of conformity
in accordance with the ECMachinery Directive 2006/42/EC,
AnnexII, Part1, SectionA
Herewith, we– TrotecGmbH– declare that the machinery designated below was developed, constructed and produced in compliance with the requirements of the ECMachinery Directive in the version 2006/42/EC.
Product model/ product:
Product type:
Year of manufacture as of:
Relevant EUdirectives:
• 2011/65/EU: 1July 2011
• 2012/19/EU: 24 July 2012
• 2014/30/EU: 29March 2014
• 2014/35/EU:8 September 2017
Applied harmonised standards:
• EN 55014-1:2006/A1:2009
• EN 55014-1:2006/A2:2011
• EN 60335-1:2012/A11:2014
• EN 60335-2-1:2012/A12:2017
• EN 60335-2-40:2003/A11:2004
• EN 60335-2-40:2003/A12:2005
• EN 60335-2-40:2003/A1:2006
• EN 60335-2-40:2003/A2:2009
• EN 60335-2-40:2003+A11:2012+AC:2013
• EN61000-3-2:2014
• EN 61000-3-3:2013
Applied national standards and technical specifications:
• EN 55014-2:2015
Manufacturer and name of the authorised representative of the technical documentation:
Trotec GmbH Grebbener Straße 7, D-52525 Heinsberg Phone: +49 2452 962-400 E-mail: info@trotec.de
DH 15, DH 30, DH 60
dehumidifier
2019
Place and date of issue: Heinsberg, 15.09.2015
Detlef von der Lieck, Managing Director
22 EN
dehumidifier DH 15 / DH 30 / DH 60
Trotec GmbH
Grebbener Str. 7 D-52525 Heinsberg
+49 2452 962-400 +49 2452 962-200
info@trotec.com www.trotec.com
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use