Page 1
BS06
EN
OPERATING MANUAL
DIGITAL SOUND LEVEL METER
TRT-BA-BS06-TC2013-28-002-EN
Page 2
Table of contents
Notes regarding the operating manual................................. 2
Safety .....................................................................................2
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
Information about the device................................................3
Transport and storage...........................................................4
Operation ...............................................................................4
Errors and faults....................................................................5
Maintenance and repair ........................................................5
Disposal .................................................................................6
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information
(e.g. material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
BS06
https://hub.trotec.com/?id=43270
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Do not immerse the device in water. Do not allow liquids to
penetrate into the device.
• The device may only be used in dry surroundings and must
not be used in the rain or at a relative humidity exceeding
the operating conditions.
• Protect the device from permanent direct sunlight.
• Do not expose the device to strong vibrations.
• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible
condition.
• Do not open the device with a tool.
• Only use the device if sufficient safety precautions were
taken at the surveyed location (e.g. when performing
measurements along public roads, on building sites etc.).
Otherwise do not use the device.
• Observe the storage and operating conditions as given in
the Technical data chapter.
2 EN
digital sound level meter BS06
Page 3
Intended use
1
2
5
6
7
3
4
Only use the device for sound level measurements within the
measuring range specified in the technical data.
To use the device for its intended use, only use accessories and
spare parts which have been approved by Trotec.
Improper use
Do not use the device in potentially explosive atmospheres, for
measurements in liquids and at live parts. Trotec accepts no
liability for damages resulting from improper use. In such a
case, any warranty claims will be voided. Any unauthorised
modifications, alterations or structural changes to the device are
forbidden.
Personnel qualifications
People who use this device must:
• have read and understood the operating manual, especially
the Safety chapter.
Personal protective equipment
Wear hearing protection
Wear hearing protection when handling the device.
Note
To prevent damages to the device, do not expose it to
extreme temperatures, extreme humidity or moisture.
Note
Do not use abrasive cleaners or solvents to clean the
device.
Information about the device
Device description
By use of the digital sound level meter BS06 the sound level can
be measured in dB(A) in real time.
A MAX/MINfunction is available for the assessment of the
measurements.
The display illumination automatically adjusts to the ambient
light conditions.
When not in use, an automatic switch-off saves the battery.
Device depiction
Residual risks
Hazardous electric current
Work on the electrical components must only be
carried out by an electrically skilled person or an
authorised specialist company.
Warning
Risk of hearing damage!
Ensure sufficient ear protection when there are sources
of loud sound. There is a danger of hearing damage.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Caution
Keep a sufficient distance from heat sources.
No. Designation
1 Microphone with wind shield
2 MAX/MIN button
3 Tripod thread
4 Battery compartment with cover
5 Display
6 Light sensor
7 Power button
EN 3
digital sound level meter BS06
Page 4
Display
9
8
10
4
13
No. Designation
8 Minimum value indication
9 Indication of the measured value in dB(A)
10 Maximum value indication
Technical data
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
For transporting the device use a suitable bag to protect it from
external influences.
Storage
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• protected from dust and direct sunlight
• with a cover to protect it from invasive dust if necessary
• The storage temperature is the same as the range given in
the Technical data chapter.
• Remove the batteries from the device.
Parameter Value
Model BS06
Weight 140g
Dimensions
132mmx 56mmx 33mm
(lengthx widthx height)
Measuring range 30 to 130dB(A)
(31.5Hz to 8kHz)
Accuracy ± 3.5dB (at 1kHz and 94dB)
Measuring range resolution 0.1 dB
Time weighting 125ms
Microphone 1/2inch electret condenser
microphone
Operating temperature 0to 40°C with 10to 75%RH
Operating altitude max. 2000m
Storage temperature -10 to 60°C
Power supply 1x Alkaline 9V battery
battery life: approx. 5000 to
8000measurements
Automatic switch-off after approx. 15minutes
Operation
Inserting the battery
Note
Make sure that the surface of the device is dry and the
device is switched off.
Scope of delivery
• 1x Digital sound level meter BS06
• 1 x 9V battery
• 1 x Wind shield for microphone
1. Remove the cover(4) from the device by sliding it in the
direction of the arrow.
2. Use the battery clip(13) to connect the new battery with
correct polarity.
3. Slide the cover(4) back on the device.
• 1x Manual
4 EN
digital sound level meter BS06
Page 5
Switch-on and measurements
1. Press the power button(7).
ð The display will be switched on and the device ready for
operation.
ð In case of poor lighting conditions the display
illumination switches on automatically. The display
illumination is controlled by the sensor(6).
2. Point the device with the microphone end directly toward
the sound source.
ð Reach out as far as possible to hold the device away
from your body or mount it to a tripod via the tripod
thread(3). This helps to avoid foreign influences during
the sound measurement.
ð If it is windy (>10m/s) use the supplied wind shield so
as not to falsify the measured value.
ð The measured value will be displayed indB(A).
Note:
Note that moving from a cold area to a warm area can lead to
condensation forming on the device's circuit board. This
physical and unavoidable effect can falsify the measurement.
In this case, the display shows either no measured values or
they are incorrect. Wait a few minutes until the device has
become adjusted to the changed conditions before carrying out
a measurement.
Info
Please note that the measurement of a sound source
always has to be carried out directly. There must be no
objects or persons located in between the microphone
and the sound source, unless their influence on the
sound intensity is to be measured on purpose as well.
Setting the MAX/MINfunction
By use of the MAX/MINfunction you can either read the highest
or the lowest value.
1. Press the MAX/MINbutton(2).
ð The MAXindication(10) appears on the display.
ð The display now indicates the highest sound level
measured since the device was switched on.
2. Press the MAX/MINbutton(2) again.
ð The MINindication(8) appears on the display.
ð The display now indicates the lowest sound level
measured since the device was switched on.
3. Press the MAX/MINbutton(2) for 2seconds.
ð The MAX/MINfunction is deactivated and the current
measured value is displayed.
Automatic switch-off
The device comes equipped with an automatic switch-off
function. After 15minutes of non-use the device switches off
automatically.
Switching the device off
1. Press the power button(7).
ð The device is switched off.
ð The MAX and MINvalues are reset.
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
For repairs or device testing, contact the manufacturer.
Display segments are only faintly visible or flicker:
• The battery voltage is too low. Exchange the batteries
immediately.
The device displays implausible measured values:
• The battery voltage is too low. Exchange the batteries
immediately.
Maintenance and repair
Battery change
A battery change is required, when the displayed values are
difficult to read or the device can no longer be switched on.
See chapter Operation.
Cleaning
Clean the device with a soft, damp and lint-free cloth. Make
sure that no moisture enters the housing. Do not use any
sprays, solvents, alcohol-based cleaning agents or abrasive
cleaners, but only clean water to moisten the cloth.
Repair
Do not modify the device or install any spare parts. For repairs
or device testing, contact the manufacturer.
EN 5
digital sound level meter BS06
Page 6
Disposal
Li-Ion
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
In the European Union, batteries and accumulators must not be
treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6September 2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.
6 EN
digital sound level meter BS06
Page 7
Trotec GmbH & Co. KG
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
info@trotec.com
www.trotec.com
Loading...