TABLE OF CONTENTS
1. IMPORTANT SA FETY INSTRUCTIONS.... ........................................ ............................... 4
2. ENVIRONMENT PROTECTION ........................................ ..................................... ........... 5
3. MAIN FEA TURES.......................................................... ..................................... ............... 6
4. REMOTE CONTROL ........................................... ........................................ ...................... 7
5. FRONT PANEL .............................................................................................. .................... 8
6. REAR PA NEL ........................................................................... ...................................... ...8
7. HOW TO CONNECT YOUR STB ................................................................ ...................... 9
7.1 CONN ECTIN G TO TV USING RCA CON NECTOR ................................................................................... 9
7.2 TV
WITH MOT ORIZED SYSTEM (DISEQC 1.2) ..................................................................................... 9
8. REMOTE CONTROL - B ASICS ................................................................ ...................... 10
8.1 TURNONRECEIVER..................................... ...................................................................................... 10
8.2 S
TANDBY MOD E.................................................... ............................................................................10
8.3 PA USE .............................................................................................................................................. 10
8.4 M
UTE........................................................... ...................................................................................... 10
8.5 N
EXT /PREV IOUSCHANNEL .............................................................................................................. 10
8.6 V
OLU ME ............. ............................................................................................................................... 10
8.7 S
ATELLITE LIST............................................................................. ..................................................... 10
8.8 C
HANNEL LI ST ........................................................................................................................ ........... 10
8.9 N
UMERIC KEYS ............ ..................................................................................................................... 11
8.10 TV / RA DI O M
ODE ......................................................................................................................... 11
8.11 M
ENU................ ............................................................................................................................... 11
8.12 E
LECT RONIC PROGRAM GUIDE ....................................................................................................... 11
8.13 I
NFO............................................................................................................................ ..................... 12
8.14 EXIT ................................................................................................................................................ 12
8.15 N
EXT /PREVIOUS PAGE................................................................................................................... 12
8.16 T
ELET EXT .............................................................................................. .......................................... 12
8.17 S
UBTITLE ......................................................................................................................................... 13
8.18 ZOOM ............................................................................................................................................. 13
8.19 MUL TI-PICTURES............................................ ............................................................................ 13
8.20 FA V L
IST ......................................................................................................................................... 14
8.21 SLEEP............................................................................................................................................. 14
8.22 P
REVI OUSLY WA TCHI NG CHA NNEL ................................................................................................ . 14
8.23 A
UDIO CHANNEL ................................................................................... .......................................... 14
8.24 FORWORD ..................................................................................................................................... 15
8.25 PVR R
ECORD.............................................................................. ..................................................... 15
8.26 P
LAY PREV IOU S RECORDED FIL E................................................ ..................................................... 16
8. 27 PA U SE/ PL A Y
RECORDED FI LE ....................................................................................................... 16
8.28 BACK WORD .................................................................................................................................. 16
8. 29 ST OP PV R R
ECORD ........................................................................................................................ 16
17. DECLARATION OF CONFORMITY
The manufacturer herewith declares the conformity of that product with the fo llowing directives and standards:
Low Volt age Direc tiv e LVD 2006/95/EG
EN 60 065:2002+A1:2006
EMC Dir ecti ve 2004/108/EG
EN 55 013:2001+A1:2003+A2:2006
EN 55 020:2007
EN 61 000-3-2:2006
EN 61 000-3-3:1995+A1:2001+A2:2005
Model : Digital Satellite Receiver TDVB-SDB2
16. SPECIFICATIONS
Satellite specification
System standard Fully MPEG2/DVB Compliant
Channel Storage Max.4000 TV and Radio Channels totally
Input Frequency 950~2150MHz
LNB Control DiSEqC1.0/1.2, USALS
LNB Power 13V/18V (Max, 400mA)
LNB tone switch 22KHZ
Symbol rate 2~45Mb ps
A/V Mode
Video format MPEG-2 Main profile/Main level
Audioformat MPEG-1layer &
Aspect Ratio 16:9, 4:3
Audio sampling rate 32, 44.1, 48 kHz
Audio type Left channel, Right channel, Stereo
Graphic display 720x576(PAL), 720x480(NTSC)
Microprocessor & Memories
Processor CT216S-Z
SDRAM 16 Mbits
FLASH 2 Mbits
Power & Environment condition
Supply voltage 90~250V AC, 50/60Hz
Supply power Max.10W
Operational temperature 5 C~6 0 C
Physical specification
LED display red & green
Weight 0.65 kg
Dimensions 196(W) x 126(D) x 42(H) mm
Connections
Satellite IF input F-type (Digital)
Satellite IF loop out F-type (Digital)
USB Port USB 2.0
Video CVBS
Audio RCA Audio left, Audio right
Control Output 0/12V out
RS-232 Female Connector
Specification is subject to change without notice.
8.30
P
LAY NEXT RE CORDED FIL E.. .......................................................................................................... 16
8.31
T
IMESHIFT........................................................... ............................................................................ 16
9. MENU .............................................................. ................................................................ 16
9.1 GENERA L M ENU M ANA GED ROL ES............................................... ..................................................... 17
10. CHANNEL LIST ............................ ..................................... ............................................17
10.1 TV L IST,RADIOLIST....................................................................................................................... 17
10.2 F
AVORITE MANAGER.......................................... ............................................................................ 19
11. INSTAL LATION ...................................................... ....................................................... 19
11.1 SATELLITESETTING ........................................................................................................................ 19
11.2 S
EARCH CHA NNEL S ......................................................................................................................... 20
11.3 TP M
ANAGER.................................. ................................................................................................ 22
12. MULTIMEDIA ............................ ............................................................................ .........2 2
12.1 MY ALBUM............................ .......................................................................................................... 23
12.2 M
Y MUSIC ....................................................................................................................................... 23
12.3 M
Y MOV IE ....................................................................................................................................... 23
12.4 M
Y RECORDIN GS............................................................................................................................. 24
13. UTILITY.............................................. ..................................... ...................................... .25
14. SETUP .............................................................................................. ............................. 25
14.1 GENERA L SETTING .......................................................................................................................... 25
14.2 TV S
ETUP ................... ..................................................................................................................... 26
14.3 P
A SSWO RD ............................................................................................. .......................................... 26
14.4 A
DVANCE TIMER ............................................................................................................................. 27
14.5 SW U
PDA T E ..................................................................................................................................... 27
14.6 S
ET DEFA ULT ...................................................... ............................................................................ 28
15. TROUBL E SHOOTING...................................................... ............................................29
16. SPECIFICATIONS ......................................................................................................... 30
17. DECLA RATION OF CONFORMITY ............................................ .................................. 31
1. IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTION MARK S:
The lightning flash with arrow
symbol, within an equilateral
triangle, is to alert the user to
the presence of uninsulated
“ dangerous voltage” within the
product’s enclosure that may
be of sufficient magnitude to
constitute a risk to persons.
CAUTION: To reduce the risk
of electric shock, don’t remove
cover (or back). Equipment
service and maintenance
should be undertaken only by
trained personnel.
The exclamation point, within an
equilateral triangle, is intended to aler
the user to the presence of important
operating and maintenance (servicin
instructions in the literature
accompanying the appliance.
This STB has been manufactured to satisfy the international safety standards. Ple ase read the following safety
precautions carefully.
MAINS SUPPL Y: 100 - 250V AC 50/60Hz
OVERLOA DING: Do not overload wall outlet, extension cord or adapter a s this may result in fire or electric
shock.
LIQUIDS: Keep liquids away from the STB.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.
CLEANING: Disconnect the STB from the wall outlet before cleaning.
Use a light damp cloth (no solvents) to dust the STB.
VENTILA TION: The slots on top of the STB must be left uncovered.
Do not stand the STB on soft furnishings or carpets.
Do not expose the STB to direct sunlight or do not place it near a heater.
Do not stack electronic equipments on top of the STB.
ATTACHMENTS: Do not use any attachments that are not recommended as these may c ause hazard or
damage the STB.
CONNECTION TO THE SATELLITE DISH LNB:
Disconnect the STB from the mains before connecting or disconnecting t he cable from the
satellite dish.
FAILURE TO DO SO CAN DAMAGE THE LNB.
CONNECTION TO THE TV:
Disconnect the STB from the mains before connecting or disconnecting t he cable from the
satellite dish.
FAILURE TO DO SO CAN DAMAGE THE TV.
EARTHING: The LNB cable MUST BE EARTHED to the system earth for the satellite dish.
LOCATION: Place the STB indoor in order not to expose to lightening, rain or sunlight.
15. TROUBL E SHOOTING
If you have any problem with receive, before you contact with your local dea ler or after-sales center,
please read below trouble shooting information’s.
CAUTION!
Please don’t service the receiver by yourself. This could be dangerous for you
and may causereceivers damage and lost of warranty.
Problem Possible causes What to do
No LED’s light on front
panel, receiver is not
responding on RCU
Receiver is not connected to the
outlet
Make sure power cord plug is
properly plugged into outlet
No sound but LED on
front panel is shining
No or improper audio connection Check and correct Audio connection
MUTE function is enabled in rec eiver
and / or TV
Check and if needed disabl e MUTE
function in receiver and / or TV
Sound volume in receiver and / or TV
is maximally decreased
Check and if needed increase sound
volume in receiver and / or TV
No Picture & sound but
LED on front panel is
shining
Receiver is in standby mode Press Power button on front pan el or
remote control
No or weak signal Check the cable connection, LNB and
other equipment connected between
LNB and receiver and / or adjust
satellite dish
LNB Noise Factor too high Change to the LNB with lower N oise
Factor
The LNB unit is faulty Check and if needed c hange LNB
The satellite dish is not point ing at
satellite
Adjust the satellite dish, check the
signal level in Satellite Setting menu
Bad picture /
blocking error
The satellite dish is not point ing at
satellite
Adjust the satellite dish, check the
signal level in Satellite Setting menu
Signal is too strong Connect signal attenuator into th e
LNB input
Satellite dish is too small Check dish position, change to a
larger satellite dish
The LNB unit is faulty Check and if needed c hange LNB
Remote Control (RCU)
is not working
Out of battery Change the battery
Remote control is covered or aimed in
wrong direction
Aim the RCU directly at the receiver,
make sure there is no block between
RCU and front panel of the receiver
CAUTION!
If you still cannot resolve your problem with above reference, please contact your
local d ealer or th eir aft er-sal es cent er.
When you select file with new software, SW update is
done automatically and can take few minutes. When
operation will be finished receiver will switch into full
screen mode.
CAUTION: To c heck ac tual s oft ware vers ion,
press
MENU to enter i nto m enu an d th en
INFO button.
14.6 Set Def ault
Use it to load default settings into receivers memory.
To execute this operation, press
RED special
button, to abort press
MENU or EXIT .
When you made this operation, all stored channels
and settings made by user will be deleted.
2. ENVIRONMENT PROTECTION
Attention!
Your product is marked with this symbol. It means that used electrical and electronic
products should not be mixed with general household waste. There is separate c ollection
system for these products.
Information on Disposal for Users (private households)in the European Union
Used electrical and electronic equipment must be treated separat ely and In accordance with legislation that
requires proper treatment, recovery and recycling of used electrical and e lectronic equipment.
Following the implementation by member states, private households within the EU states may re turn their
used electrical and electronic equipment to designated collection facilities free of charge*. In some countries*
your local retailer may also take back your old product free of charge if you purchase a similar new one.
If your used electrical or electronic equipment have batteries or accumulat ors, please dispose of these
separately beforehand according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment,
recovery and recycling and thus prevent potential negative effects on the environment and hum an health which
could otherwise arise due to inappropriate waste handling.
InformationonDisposalforBusinessUsers
If you wish to discard of this product, please contact your local authorities and ask for th e correct method of
disposal.
*) Please contact your local authority for further details.
3. MAIN FEATURES
Fully DVB-S compliant
CPU: CT216S
MEPG-2 SD decoding (MP@ML)
DisEqC1.0 and DisEqC1.2 switching support
USALS motor Supported
CAS supported
USB PVR and Timeshift supported
JPEG and other type photo file Supported
MP3 Supported
More than 5000 channels memory space
8 Favorite channel groups
7 days Electronic Program Guide (EPG)
Channel Search with automatic, manual, blind scan
Teletext output with both VBI and OSD
Multi-language Subtitle output supported
Multi-language and 32 bits true color on screen display (OSD )supported
Aspect Ratio 4:3 and 16:9
Signal lever & quality indicator
Parental Lock
Easy and fast software upgrade through USB port or RS-232
Channel and Program editor
4 digit 7 segments channel number display
2 LED light display
1xCVBS & 2xRCA
1x0/12v
1x Smart Card Reader
1x USB2.0 port
1xLNB IN and Loop out
1xRS-232
14.4 Advanc e timer
Use this option to display timer manager with list of
events.
To add new event to the list press
RED special
button to display new, Event Edit window.
Or you can book a timer by press
RED special
button from EPG windows.
Event describes opportunity to turn off the receiver or
activate / turn on certain TV or Radio channel at
certain time and date.
Chann el Type
Select event type; Turned off the receiver, TV or
Radio channel.
Chann el No
Specify channel number which will be activated /
turned on in certain time. Option not displayed when
receiver will be turned off.
Start Date / St art T ime
Set time and date when event will start.
End Ti me
Set time when event will finish.
Mode
Set mode of executing events. Possible options; Stop,
Once, Daily, Weekly, Monthly.
14.5 SW Up date
Use this menu sheet to update receivers software
stored in connected to receiver USB sti ck.
This option is active when GMT Usage is enabled.
UseittocorrectGMTtimeduetovalidTimeZone.
14.2 TV Set up
TV For mat
Use this option to set display format. choose
between: 16:9 Fit, 4:3 Fit, 16:9 Letter Box or 4:3
Letter Box setting.
TV Mod e
Use to choose TV mode standard. Possible option:
Auto, NTSC, PAL. When Auto, receiver will switch
automatically.
OSD Transparency
Use this function to set OSD transparency on one of 8
levels.
Banner Display Time
Use it to set how long will be displayed on the bottom
of the screen banner with information about actual
channel. Available settings: 1s, 3s, 5s, 10s, 30s,
Always.
14.3 Pass wo rd
Menu Lock
Enable this option to protect by password menu from
outside changes. Each enter into menu will require
password.
Channel Lock
Enable this option to protect by password all locked
channels. When you will try to view locked channel
first you will need to enter password.
To set list of locked channels – please see 10.1 Lock
function.
Censorship Lock
Enable this option to protect children from watching
prohibited channels.
You can set total lock for all channels or choose
number from 1 to 18 which represent minimal age of
your children. If presented program will be allowed
from person older that minimal age, to watch it,
password will need to be entered first.
CAUTION: Some channel signals can broadcast
information about minimal age under which
services are prohibited before watching. Because
this kind of information is not obligatory,
censorship lock will wor k only with selected
channels.
ChangePassword
Activate this option to change password. Def ault
pass word is “ 0000” . Enter new password and
confirm it once more.
CAUTION: A ll rec eiver l ock is p rotec ted b y th e
same password.
4. REMOTE CONTROL
POWER
Power ON/Standby the receiver
MUTE
Mutes the sound
0-9
Enter the channel’s number.
Switch back to previous channel.
VFORMAT
Switch NTSC/PAL
AUDIO
Switch audio mode: stereo, left, right.
FREEZE
Freeze the picture when play channel.
LANGUA GE
Switch between multi-language when play channel.
INFO
Shows current channel’s information bar.
V+/V-
Turn Up/Down while play program.
CH+/CH-
Switch to the up/down channel.
P+/P-
Page up/down.
FAV
Switch between favorite channel groups.
TV/Radi o
Switch between TV and Radio mode.
SLEEP
Make receiver sleep after a appointed time.
EPG
Show EPG(Electronic Program Guide).
///
Up/Down/Left/Right, channel change, move cursor or turn
up/down volume.
OK
Confirm selection or display “OK LIST” of channels.
MENU
Show main menu or back to previous menu from sub-menu.
EXIT
Escape from present menu.
Color Button
Function key and one key access also.
SUB
List current usable subtitle language.
TTX
List current usable teletext language.
TV/STB
Invalid key
SAT
List current satellites which within channel.
/
Start/End, go to the previous/next recorded file, and play it
/
FF/FB, Fast forward/backward to view the current played TS
/
Begin to recording when playing program/ stop playing or
recording.
Play program, recorded file or music file.
Start timeshift function or pause a playing program.
5. FRONT PANEL
POW ER
To switch the receiver power on/standby
Menu
Show main menu or back to previous menu from sub-menu
OK
Confirm selection or display “OK LIST” of channels
CH-/+
Switch to the up/down channel.
VOLUME-/+
Turn Up/Down while play program.
6. L ED Li ght Indicator
Double color, green color in dicates signal is good and red color indicates in
standby mode.
7SegmentsLEDDisplay
Display channel number.
Smar t C ar d Reader
Open the case and insertone smart card in this slot.
6. REAR PANEL
Please refer to the diagram above for all possible connections of your receiver.
Do not connect the unit to the mains socket until all other connections have been made and
checked.
1- LOOP OUT
Loop out the satellite signal to other device.
2- LNB IN
Connect to satellite antenna cable
3- USB 2.0
For SW-Update, PVR, Timeshi ft, Picture viewing, MP3 playing, backup and restore.
4- 0/12V
Connect to 0/12 switch.
5- CVBS
Connect to the TV’s video p ort.
6- R/L AUDIO
Connect to TV’s audio ports.
7- RS-232
For SW-Update or other functions.
8- Pow er Li ne
Power line
App earance of rec eiver , peri pheries an d also m enu c an chang e depend f rom r eceiv ers m odel
or softwareversion and will not influence on its functionality and technical parameters.
1
1
2 3 4
5 6
7 8
2
3
4 5
6
7 8
13. UTILITY
On this menu sheet you can find game Gomoku,
calendar and calculator.
14. SETUP
This menu sheet managed general receiver settings,
TV Settings, Passwords, Advanced Timer Settings,
SW Updates and restoring Default Settings.
14.1 Gener al Set ti ng
This menu managed language and time settings..
OSD Lang uage
Use this option to set OSD language.
Audio Language
Use this option to choose default audio language for
channels which have more than one audio track.
Subtitle Language
Use this option to choose default language for
channels which broadcast few language subtitles.
GMT usag e
Enable this function to use time and data broadcasted
in satellite signal. Disable this function to set time and
data manually.
Dayli ght Ti me
Enable this function to use SUMMER/WINTER time.
Tim e Zone
12.4 My Rec or di ngs
Choose this option to change your receiver and
connected into Recorded list , change recording
preference.
Recording List Page:
Recording Device Page:
Recording Preference Page:
7. HOW TO CONNECT YOUR STB
We offer you the way of connecting the STB to your TV. Consult your local supplier for a ssistance in
setting-up your system that is best suited to your requirements.
7.1 Connecting to TV using RCA Connector
7.2 TV wi th Motorized System (DiSEq C 1.2)
WhenyouplantouseinyoursatellitesystemDiSEqC1.2motoryouneedtohavetwoconcentric
cables with type F connectors on both ends. First cable use to connect LNB unit with DiSEqC motor,
next use to connect DiSEqC motor with receiver.
All our receiver are compatible with DISEqC 1.0 and DISEqC 1.2. To receive from one satellite dish
signals from two or more satellites use system with few LNB units (separate LNB unit for each
satellite) and 2/1 or 4/1 DiSEqC switch. To reduce connection cable lengt h and reduce total cost use
outer switch.
To adjust system chooses LNB type in Satellite Setting menu. Then set LNB unit to receive signal of
the best quality. Further use standard channel searching.
CAUTION: To inc rease yo u sat ellite s ystem f or extr a LNB un its y ou need t o have s atell ite d ish
larg er than 0 .8 m.
8. REMOTE CONTROL - BASICS
8.1Turnonreceiver
Plug on power cord connector to outlet. Or press
Power button on the front panel or remote
control when STB is standby.
Frequently Asked Questions
Question: Power cord connec tor was plugged on
and receiver is not in standby mode, but nothing
is displayed on TV screen?
Answer: Make sure that receiver is connected to right
TV input; e.g. when you connect receiver to
connection Video 1, TV had to be set on source Video
1.
Question: Power cord connec tor was plugged on
and receiver is not in standby mode, but TV
screen display information “No signal” or “Weak
signal”.
Answer: This mean there is no signal on this channel.
A few reasons can cause this effect:
1. Dish is set on differ satellite than chosen channel
become from.
2. signal of this channel is not strong enough. Try to
choose other channel. If necessary set properly
dish position or contact with Your Local Dealer or
Servicing.
8.2 Standby Mode
1. By pressing Power button receiver is going
from operational mode to standby mode.
2. By pressing
Power button receiver is going
from standby mode to full screen mode on last
watching channel.
8.3 PAUSE
When you pres s PAUSE button while receiver is
in playing mode, will pause playing. Start playing
again, please press
PAUSE once more.
8.4 Mute
1. Press the button (Mut e) on remote control
to turn off sound. On the screen appears symbol:
.
2. Press the button
(Mute) once more to tu rn on
sound.
8.5 Next / Pr evi ous channel
When receiver is in full screen mode, if you want to
change channel, you can press
▲,▼ buttons on
remote control or front panel.
8.6 Vol ume
When receiver is in full screen mode, to change
volume press
◄,► or VOL UME +, VOLUMEbuttons on remote control; left to decrease, right to
increase sound.
8.7 Satellite list
To change satellite, press OK buttontogofrom
full screen mode to channel list and then
SAT
button. Use ◄,► to choose satellite from list and
confirm by
OK button. To choose certain channel
use
▲,▼ buttons.
8.8 Channel list
1. When receiver is in full screen mode, press the
button
OK or SA T to display TV channels
list. More info in TV List Menu description.
2. To back to full screen mode, press
OK or
EXIT button.
12.1 My A lb um
Choose this option to view pictures stored on
connected to receiver USB stick.
12.2 My Music
Choose this option to change your receiver and
connected into MP3 Player.
12.3 My Mo vie
Choose this option to change your receiver and
connected into Movie Player.
3. NIT Searching.
Enable this option to allow receiver looking for
information about new transponders broadcasted in
satellite signal. This allows increase number of
searched channels. It is advice to enable this option
even if this will increase searching time.
When option will be chosen, press
OK to sta rt
searching.
When searching finish, receiver will back to full
screen mode.
11.3 TP Manager
This menu allows managing transponders from active
satellite. If you want change satellite press
SAT .
When you press
BLUE special button in this
position, “SAT Setting” window will be displayed.
TP Manager allows adding, deleting, editing and
scanning certain transponders:
1. Add.
To add new transponder to the list, press
RED
special button. In displayed window use
▲,▼,◄,► and numeric keys to 0~9, to enter TP
parameters like: Frequency, Symbol Rate and
Polarity.
2. Del ete.
To delete actually selected transponder press
GREEN special button. When you want delete all
transponders valid for actually selected satellite,
press
YELLOW special button.
3. Ed it.
To change settings of actually selected transponder
press
OK . In displayed window, to enter new TP
settings; Frequency, Symbol Rate and Polarity.
Confirm by
OK .
4. Sc an.
To scan actually selected transponder press
BLUE special button. In opened window to
choose what type of channel you want search; All or
Free only.
12. MULTIMEDIA
Multimedia sheet allow to use receiver as picture
browser or MP3 Player for files stored on USB stick.
8.9 Numer ic K eys
When receiver is in full screen mode you can choose
channel by enter channel number by numeric keys
and wait a while for change. When you enter channel
number and confirm this by
OK button, channel
will change immediately.
8.10 TV / RADIO Mode
When receiver is in TV mode, press button
TV/RADIO to switch to Radio mode.
When receiver is in Radio mode, press button
TV/RADIO to switch to TV mode.
8.11 Men u
When receiver is in full screen mode, press the button
MENU to enter to receivers menu.
8.12 Electronic Progr am Gu id e
1. Receiver have implemented EPG function which
allow enter into TV or Radio program guide and
display information about actual and future
programs which will be transmitted. This function
is working only with channels which broadcast in
signal EPG information. Press
EPG button to
display EPG window.
2. Press OK button to display details about
actual and next program transmitted by channel.
8.13 Info
When receiver is in full screen mode, press the button
INF to display frame with actual channel
parameters.
8.14 EXIT
To leave receivers menu and back to full screen
mode, press
EXIT button.
8.15 Next / Previous page
To choose next/previous page use P+, P- butt ons
on remote control.
8.16 Teletext
When receiver is in full screen mode, press button
TEXT (RED) will show the list of available teletext
languages. If current channel don’t have teletext,
option “Enabled” will be displayed.
To switch between left/right part use ◄,► ,to
confirm your choice press
OK .
Choose satellite on from the list and press
YELLOW special button to exe cute “SAT Setting”
window.
Choose one or select few satellites from the list and
press
BLUE special button to execute “Aut o
Scan”. Displayed window will have few options:
1. Progr am.
You can define type of searched channels. Two
option are available: All or Free only.
2. Scan Mod e.
You can choose between easy searching and
Blind-Scan. Blind scan can searching full frequency
rate and looking for transponders.
Main window have two parts; left with actual settings
and left which present all possible option for chosen
parameter.
Possible settings:
1. Satellite.
Actual satellite name is displayed on the left. Right
part will list all actually programmed satellites. To
change active satellite, choose new one from
presented list and confirm by pressing
OK .
To add to the list new satellites, press
RED
special button. In new window, you can select
preferred satellites. You can choose between
satellites stored in receiver’s memory and option „Add
SAT” by which you can define your own satellite.
To delete active satellite from the list, press
GREEN special button and confirm by OK .
Use
YELLOW special button to change satellite
name.
To begin satellite searching, press
BLUE special
button.
CAUTION: It is not possible to removefrom the
satellites of default list.
2. Transponder.
Choosing this option will show the transponders list
for actual satellite.
Press
RED special button to change motor
settings:
Moto r pos iti on: One of store d in receiver’s memory
motor positions can be chosen.
Move Co nti nue. Motor can be moved in east/west
direction continuously.
Move St ep. Motor can be moved in east/west
direction by steps. Use this option to small & slow
correction of dish position.
SetEastLimit/SetWestLimit.
Allow to define position limits e.g. to not hit into
barrier. Find critical position and press
OK to
storeitinmemory.
Disab le Limi t. Choose this option and press
OK
to deactivate defined limits.
Goto Ref . Press
OK to set dish in reference
position.
OK. Select and confirm OK b utton in displayed
window to store and set entered settings.
3. LNB Type .
You can choose LNB type which will be use to
receive signal from satellite.
4. LNB Low Freq / L NB High Fr eq
If active LNB type allows this, you can define upper
and / or lower LNB frequency limit.
5. 22K Tone.
If active LNB type allows this, you can enable /
disable 22kHz tone.
6. 12V.
Enable / disable 12V output.
7. DiSEqC.
You can switch between four DiSEqC ports.
8. Tonebur st.
Enable / disable toneburts.
9. LNB Power.
You can choose LNB power.
11.2 Searc h c hannels
Main window is shared on two parts; left present
satellite list, right – all parameters of actually chosen
satellite:
8.17 Subtitle
1. When receiver is in full screen mode, press
button
SUB (GREEN) to enable/disable
subtitles displayed on the bottom of the screen.
This function is working only with channels which
broadcast in signal subtitle information.
8.18 ZOOM
1. When receiver is in full screen mode, press
ZOOM (Yell ow) to st art zoom function.
8.19 MULTI-PICTURES
1. When receiver is in full screen mode, press
MP (Bl ue)to start zoon function.
2. Use
▲,▼ and ◄,► to select channel,
then Press
OK to view the channel.
8.20 FAV Li st
1. FAV List is a list of 8 groups of channels which
can be managed by Favorite Manager.
2. During watching TV channel, press
FAV
button. In the right upper corner appear icon
present active FAV list.
3. By pressing
FAV button next FAV list will be
activated.
Frequently Asked Questions
Quest ion: Wh y on t he sc reen ap pear i nform ation
“No FAV List” , when I press
FAV button?
Answer: Any channel was assigned to FAV list, you
should add a channel to a favorite group at least.
8.21 SLEEP
To set sleep timer or change the sleep timer use
SLEEP buttons on remote control, the .The unit is
minute.
8.22 Previously watching channel
Press the button RECALL on remote control to
back on last watching channel.
8.23 Audio channel
1. When receiver is in full screen mode, press button
AUDIO button to disp lay audio channel
window.
2. You can change sound mode to Stereo/Left
channel/Right channel.
To leave Find function window press EXIT or
MENU .
10.2 Favorite Manager
Receiver have 8 favorite channel lists signed as
FAV1 – FAV8, to which selected channels c an be
assigned from the total channel list stored in
receivers memory.
Favorite Manager allow to manage previously
prepared Favorite lists by deleting channels from
lists and edit names of FV lists. Press
GREEN
special button to switch between TV/Radio
channel list.
1. Delete ch annel s
To delete channels from certain FAV list, Choose the
Favorite list, then use
▲, to find channel and
press BLUE special button to sect it. Channels
selected to delete will have red mark next to channel
name. Repeat all steps to select all not wanted
channels.
To delete selected channels from the list press
YELLOW special button and confirm choice by
OK .Press EXIT to leave function men u
without deleting selected channels.
2. Edit Favorite list name (description)
To display edit name window, press
OK button.
New window will be shared on two columns; left
column present FAV1 – FAV8 lists, right
names/descriptions of these lists.
To change name/description use
▲, to select
certain group and the
◄,► to switch between
default names. Press
OK to confirm.
To enter your own name/description select group and
press
BLUE special button - edition window with
screen keyboard will be displayed (see 10.1 Edit
function).
When new name/description will be ready choose
“OK” button on displayed keyboard and confirm
choice by
OK button. To leave screen keyboar d
without any changes use
EXIT .
11. INSTALLATION
Menu sheet “Installation” has four options; Satellite
Setting, Search Channels, TP Manager.
11.1 Satellite Setting
Assignation to certain FAV list is made by choosing
channel and pressing numeric key 1~8 dedicated to
certain list. Assignation will be marked by activation
one of 8 icons displayed on the right side of the
screen.
Next way how to assign channel to Fav List/Lists is
Fav List menu which appear after pressing
OK
button. Use ▲, and OK to assign channel.
Press
EXIT or MENU to back to previous
menu.
All changes needs to be stored in memory by
pressing
YELLOW sp ecial button and confirm
choice by
OK .
7. Lo ck.
Choose the channel and to change channel status
(lock/unlock). When channel is locked, next to
channel name appears padlock mark. Repeat
operation for all channels which should be locked.
Save changes by pressing
YELLOW special
button and confirm choice by
OK .
When channel lock password will be activated in
Password menu, locked channel won’t be displayed
before right code will be entered in presented window.
See parental lock.
8. Edi t.
This function allow to change name under which
channel was stored during searching channels. Use
▲, to choose channel from the list an d press
OK to display edition window with channel
parameters. Select channel name and press
OK .
New, edition window with screen keyboard appear.
Extra function is available by special keys. Mark any
char and press
OK to inse rt it. When you finish
choose “OK” button on displayed keyboard and
confirm choice by
OK button. To leave screen
keyboard without changes in name use
EXIT .
To save and exit edition menu use
RED special
key.
9. Mov e.
Use this function to change channels order on the list.
Use
▲,▼ to select channel and press OK .
Next to channel name appears select mark. Now use
▲,▼ to define new channel position on the list
and press
OK again. All changes ne ed to be
stored in memory by pressing
YELLOW special
button and confirm choice by
OK .Press EXIT
or MENU to restore previous channel list.
10. Sort.
Function allow sort channel list according to certain
criteria. After leaving this menu channel list will have
new channels order.
To choose certain sort criteria press
OK and use
▲, to choose from displayed list one of the
option. Confirm you choice by
OK .
Other option is to use special keys. Press
GREEN
special button to sort channels according to alphabet.
Press
YELLOW spec ial button to sort according
to criteria free/CA. To change sort order to the
opposite, press dedicated button twice.
CAUTION: Time required to sort channel depends
from total number of stored channels.
11. Skip.
To skip certain channels during changing channels on
the next one use Skip function. The way of choosing
channels which should be skipped is similar to
choosing locked channels.
12. Delete.
This function allows to delete selected channels from
the channel list. The way of choosing channels which
should be deleted is similar to choosing locked
channels.
Use
▲, and press OK to change channel
status. Channels selected to delete will have red mark
next to channel name. Repeat all steps to select all
not wanted channels.
To delete selected channels from the list press
YELLOW special button and confirm choice by
OK .Press EXIT to leave function men u
without deleting selected channels.
13. Find.
Use function to find on channel list channel or
channels which starts from certain phrase.
To execute function, press
OK - edition window
with screen keyboard and space for looking phase
appear (see Edit function).
When you enter looking phrase press
YELLOW
special button – on new list will be displayed only
channels which starts from entered phrase.
8.24 FORWORD
1. When receiver is playing PVR file, MP3 or Movie,
or in timeshift mode, Press the button
FF on
remote control to change Fast-forword speed.
2. By pressing
PAUSE OR PL AY/PAUSE
button to back to normal play speed.
8.25 PVR Reco rd
1. When receiver is full screen mode, pre ss button
REC to start recording function.
2. Then, you can press
OK to confirm to start
recording, or if you don’t want to start recording,
please press
EXIT .
CAUTION: If t he par ameter of “ Mul tim edia”
-> ”My Recordings” -> ” Recording
Prefer ence” -> ” One Bu tton Rec ordin g” i s ON,
step 2will be skipped.
8.26 Play Pr evi ous recorded file
When receiver is playing recorded file, press button
PREV to play previous recorded file.
8.27 PAUSE/PL AY r eco rd ed f il e
1. When receiver is playing recorded file, press
button
PLAY/PA USE t o pause.
2. Then, you can press the button again, rest art to
play.
8.28 BACKWORD
1. When receiver is playing PVR file, MP3 or Movie,
or in timeshift mode, Press the button
BF on
remote control to change Fast-backward speed.
2. By pressing
PAUSE OR PLAY/PAUSE
button to back to normal play speed.
8.29 STOP PVR Reco rd
When receiver is recording, press button
STOP to stop recording function. Then, you can
press
OK to confirm to stop recording, or press
EXIT to go on recording.
8.30 Play Nex t r ecorded file
When receiver is playing recorded file, press button
NEXT to play Previous recorded file.
8.31 Timeshift
When receiver is full screen mode, press button
PAUSE to pause playing. Then, after some
time, you can press
PAUSE to restart to play
again, now you are in timeshift mode. Use
FF /
FB to play forword /backword.
CAUTION: Please make sure there is enough
space in your USB disk and the parameter of
“Multimedia”->”My Recordings” ->”Recordi ng
Preference”->”Timeshift” is Pause or Auto.
9. MENU
Press MENU button on remote control to display
menu as on picture below:
9.1 General m enu managed roles
Please read carefully below information’s about
general roles how to managed receivers Menu.
1. Press
◄,► to switch between menu
sheets; Channel list, Installation, Multimedia,
Utility, Setup, Free + CA.
2. Use
▲,▼ to choice certain option on menu
sheets.
3. Press
OK to choose certain function.
4. To leave menu and back to full screen mode
press each time
EXIT or MENU .
5. To back to previous menu level use
EXIT or
MENU .
6. After choosing certain function, next settings can
be made by buttons
▲,▼,◄,► and / or
numeric keys 0~9 and sp ecial key s
RED,
GREEN, YELLOW, BLUE
,whichworks
according to information’s displayed on blue strip
on the bottom of screen.
7. Press
OK to execute chosen function or
display next window.
8. When any changes were made, usually is
required to store it. If you will try to leave menu
without previous storing them in memory, extra
window with question about storing will be
displayed. Press
OK to save changes or
EXIT to cancel them.
10. Channel List
Menu sheet “Channel list” have few options; TV List,
Radio List, Favorite Manager.
10.1 TV Li st, Radio List
When TV / Radio List will be chosen, below window
will appear on the screen:
1. Choose the channel from the list
2. Use
◄,► to choose one of special function s:
Fav, Lock, Edit, Move, Sort, Skip, Delete, Find.
3. To execute function for certa in channel, choose
channel and preferred function, then press
OK
button.
4.
RED special button enable to leave menu
and view actually chosen channel.
5. Use
SAT and ◄,► switch between
channel lists valid for certain satellite.
6. Favo rite.
This function allows to select and assign channels to
one of 8 Favorite lists. One channel can be assigned
to more than one Fav List.
Loading...