TM
MODELS: UT CT ST
Station mode instructions
For Office furniture, storage cabinets, lockers, safes, vaults, secured enclosures
The factory master code is: 135243
The factory supervisor code is: 123
Getting Started
P
R
P
Two operating modes:
1. Station mode (repeated use with the same code)
2. Locker mode (use with a temporary code)
The operating mode is specified at the time of order.To determine the lock`s operating mode, remove the
battery, press and release the program button, and reinsert the battery.
Green
Proceed
LED
Battery
holder
with cover
(green, red, yellow) indicates station mode
(green, yellow, red) indicates locker mode
Red
Error
LED
Yellow
Low battery
LED
Location to
Program
button
Push thin
front edge
inward
point the
key-fob
Knob
in locked
position
Press
Here
Keypad
Program button:
Initiates the programming mode.
When pressed the green LED will illuminate.
Infrared Receiver:
Receives a signal from an electronic
TriTeq key-fob when it is pointed at the
receiver located behind the program button.
Knob:
Moves the lock mechanism from
the locked and unlocked states.
Multiple levels of access:
1.Master code and/or blue control key fob
2.Supervisor code and/or black key fob
3.User code and/or black key fob
TM
Note: The
is pre-programmed with a factory master code and a factory supervisor code.
Operation:
Unlock by entering a valid code. The green LED will illuminate. Turn the knob to unlock.
To lock, turn the knob to align the knob pointer with the lock icon on the keypad.
Programming Chart Symbols:
P = press program button
- Solid color indicates LED is lit
- Indicates LED is flashing
- Location to point the key-fob
-
(Nx) Indicates flashes N times
1,2,3,4,5 = Indicates the button number to press
Note: If there are any errors in executing the steps below or too much time
elapses between the steps, (3x) and the lock will exit the programming mode.
1
Station Mode Programming Instructions:
CHANGE THE MASTER CODE (6 DIGITS) USING THE FACTORY MASTER CODE
factory master code factory master code new master code (2x)
Example:
Result: Factory master code 135243 was erased and the new master code 112233 was accepted
135243 135243 112233 112233
CHANGE THE SUPERVISOR CODE (3-6 DIGITS) USING THE FACTORY SUPERVISOR CODE
factory supervisor code (6x)
Example:
Result: Supervisor code 123 was erased and supervisor code 4321 was added
4321123
new supervisor code
(6x)
ADD A USER CODE (3-6 DIGITS) USING THE SUPERVISOR CODE
supervisor code user code (6x)
Example:
Result: Supervisor code 4321 was used to add user code 54321
4321 54321
(6x)
CHANGE THE MASTER CODE (6 DIGITS)
old master code old master code new master code (2x)
Example:
Result: Old master code 112233 was erased and the new master code 123455 was accepted
112233 112233 123455 123455
CHANGE THE SUPERVISOR CODE (3-6 DIGITS) USING THE CURRENT SUPERVISOR CODE
old supervisor code new supervisor code (6x)
Example:
Result: Supervisor code 4321 was erased and supervisor code 111555 was added
1115554321
(6x)
2
CHANGE THE SUPERVISOR CODE (3-6 DIGITS) USING THE MASTER CODE
master code new supervisor code (6x)
Example:
Result: Master code 123455 was used to change the supervisor code to 531
531123455
(6x)
ADD A CONTROL FOB
point blue control fob at and press the fob button (6x)master code
Example:
Result: Master code 123455 was used to add a control fob
123455
(6x)
CHANGE THE SUPERVISOR CODE (3-6 DIGITS) USING THE CONTROL FOB
point blue control fob at and press the fob button
supervisor code (6x)
Example:
Result: the control fob was used to add the supervisor code 543
543
(6x)
ADD A SUPERVISOR FOB USING THE MASTER CODE
point black supervisor fob at and press the fob button (6x)master code
Example:
Result: Master code 123455 was used to add a supervisor fob
123455
(6x)
ADD A SUPERVISOR FOB USING THE CONTROL FOB
point blue control fob at and press the fob button
at
Example: (6x)
and press the fob button
(6x)
Result: A control fob was used to add a supervisor fob
point black supervisor fob
3
ADD A USER FOB USING THE SUPERVISOR CODE
point black user fob at and press the fob button (6x)supervisor code
Example:
Result: Supervisor code 543 was used to add a user fob
543
(6x)
ADD A USER FOB USING THE SUPERVISOR FOB
point black supervisor fob at and press the fob button
and press the fob button
at
Example:
(6x)
(6x)
point black user fob
Result: Supervisor fob was used to add a user fob
TO UNLOCK WITH A FOB
Point a valid fob or at and press the fob button turn the knob to unlock the lock
Example:
Result: A fob was used to unlock the lock
or
ADD A USER CODE (3-6 DIGITS) USING USING THE CONTROL FOB
point blue control fob at and press the fob button (6x)new user code
Example:
Result: User code 321 was added using the control fob
321
(6x)
REMOVE THE USER CODE AND USER FOB USING THE CONTROL FOB
point blue control fob at and press the fob button (6x)
Example:
Result: Control fob was used to remove to remove the user code and user fob
11111
(6x)
1 1 1 1 1
4
REMOVE THE USER CODE AND USER FOB USING THE SUPERVISOR CODE
supervisor code (6x)
Example:
Result: Supervisor code 543 was used to remove to remove the user code and user fob
1 1 1 1 1
11111543
(6x)
REMOVE THE USER CODE AND USER FOB USING THE SUPERVISOR FOB
point black supervisor fob at and press the fob button (6x)
Example:
Result: Control fob was used to remove to remove the user code and user fob
11111
(6x)
1 1 1 1 1
Lockout
After 10 consecutive incorrect unlocking attempts, the lock will enter in a “Lockout mode” for two minutes.
While in lockout mode, the operation is temporarily disabled. Each key press will trigger the red LED and the
alert will sound three times. Two minutes after the last key was pressed, the lock will return to normal state and
can be used as intended.
Double digit codes:
The numbers 6, 7, 8, and 9 can be entered by pressing two keys simultaneously in order to produce a sum.
For example 2 and 4 can be pressed simultaneously to produce the number 6 (2+4=6).
Note: if the code was programmed using 2+4 as the 6 digit, the 2+4 must be used when accessing the lock, because
other combinations that equal six such as 1+5 are distinguished from 2+4.
Switching Modes
Note: The master code is retained when switching modes.
1. Unlock the and turn the knob to the unlocked position
2. Remove the battery for 10 seconds
3. While holding the program button , reinsert the battery and wait until all 3 LED’s
fade in and fade out simultaneously
4. Release the program button
5. Enter the 6 digit master code. When the master code is entered correctly,
the yellow LED will illuminate
6. Press button number 2 for LOCKER MODE, Press button number 1 for STATION MODE
Once the lock switches modes, the LED’s will flash in a specific sequence for each mode:
7.
a)
b)
8. Proceed to operate the lock in the selected mode
TM
Station Mode:
Locker Mode:
To watch the programming videos for the station mode please visit:
or the locker mode video instructions please visit:
http://microiqlock.com/locker_mode
http://microiqlock.com/station_mode
01-00003
5
Loading...