1
Owner’s Manual
SNMP/Web Management Accessory Card
Model: WEBCARDLX
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2018 Tripp Lite. All rights reserved.
Read this manual carefully before installation. A separate downloadable
User’s Guide can be found by going to www.tripplite.com/support and typing
WEBCARDLX in the search field. Refer to the User's Guide for additional
information about configuration and operation.
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an ISOBAR6ULTRA
surge protector—a $100 value!
www.tripplite.com/warranty
Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com
Ce manuel est disponible en français sur le site Web de Tripp Lite : www.tripplite.com
Русскоязычная версия настоящего руководства представлена на веб-сайте
компании Tripp Lite по адресу: www.tripplite.com
18-02-314-93358E-EN.indd 1 2/26/2018 2:50:29 PM
2
A
Ethernet Port: RJ45 jack connects the WEBCARDLX to the network using a
standard Ethernet patch cable. The Link LED A1 and Status LED A2 indicate the
operating conditions, as shown in the table on page 3.
B
Micro-USB Port: Use this port to directly connect with a computer running a
terminal emulation program. A cable (part number 73156A) is included with the
WEBCARDLX. If you need to order a replacement cable, contact Tripp Lite
Customer Support at 773.869.1234.
C
Type-A USB Port: Use this port to connect a Tripp Lite ENVIROSENSE 2 module
(E2MT, E2MTDO, E2MTDI, E2MTHDI) for a variety of environmental monitoring and
control options. See www.tripplite.com for more information about these modules.
Note: Do not connect a keyboard or mouse to this port.
D
Reset Button: The reset button is recessed, accessible through a small hole
under the RJ45 network port. Use a paper clip or other suitable object to press
the reset button for 3 seconds to reboot the network interface. Rebooting the
network interface will not erase network settings or interrupt AC power. Press and
hold the reset button for 20 seconds to restore the network interface to its factory
default settings. Restoring to the factory default will erase all previously saved
data—including network settings—without interrupting AC power.
E
Status LED: Shows WEBCARDLX status. See the table below for a description of
LED behavior.
Features
Overview
The WEBCARDLX allows users to operate any compatible Tripp Lite UPS System or
network-enabled PDU as a managed device on the network, accessible via Web
browser, Network Management Station or telnet/SSH. This manual refers to installing
the card in a UPS system, but the same instructions apply to installing the card in a
compatible PDU.
18-02-314-93358E-EN.indd 2 2/26/2018 2:50:29 PM
3
Features
CBA
EA2DA1
WEBCARDLX Legend
Identifier LED Function LED Color Status Description
A1
Ethernet
Link/Activity
Indicator
Green Flashing There is network activity on the port
Off There is no network activity on the
port
Off Perform reset via interface or reset
button
A2
Ethernet
Network
Speed
Indicator
Yellow On steady 100 Mbps network speed
Off
10 Mbps speed if A1 is flashing
Off
No network activity if A1 is also off
Off
Perform reset via interface or reset
button
E
WEBCARDLX
Status
Green On steady Normal operation
Green Single flash Power up indicator
Green/
Orange
Off No power or card is initializing
Green/
Orange
Alternating
(~1/sec.)
Software update in progress
Green/
Orange
Alternating
(~2/sec.)
Restoring factory default
configuration
18-02-314-93358E-EN.indd 3 2/26/2018 2:50:29 PM
Loading...