Tripp Lite TLP1008TEL, SUPER7 Users Manual

WARRANTY

REGISTRATION:

register online today for a chance

www.tripplite.com/warranty

to win a FREE Tripp Lite product—

Surge Suppressors

Important Safety Instructions 2
Installation 2
FCC Part 68 Notice 3
Lifetime Limited Warranty 3

Owner’s Manual

Protect It!™

Warranty Registration 4
Ultimate Lifetime Insurance Policy 4

Español 5

Français 9

1111 W. 35th Street Chicago, IL 60609 USA

www.tripplite.com/support

Copyright © 2010. All rights reserved. Protect It!™ is a trademark of Tripp Lite.

1

201010194 93-2666.indd 1 11/12/2010 9:36:52 AM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

CAUTION! DO NOT connect to an ungrounded outlet. DO NOT use with 2-wire extension

cords or adapters. This surge suppressor is designed for indoor use only. Install the surge
suppressor away from heat-emitting appliances such as radiators or heat registers. Do not
install where excessive moisture is present. Do not plug extension cords into it. Never install
electrical, telephone, network or coaxial wiring during a lightning storm. Do not drill into any part
of the housing or open the housing for any reason. There are no user-serviceable parts inside.

• Use of this equipment in life support applications where failure of this equipment can reasonably be
expected to cause the failure of the life support equipment or to significantly affect its safety or
effectiveness is not recommended. Do not use this equipment in the presence of a flammable
anesthetic mixture with air, oxygen or nitrous oxide.

Installation

Mount Your Surge Suppressor (Optional Installation. Available on Select Models Only): If
desired, mount your surge suppressor on a wall or other sturdy, vertical surface. However, you must
mount the surge suppressor prior to connecting your equipment. Place a sheet of paper over the surge
suppressor’s mounting holes and mark their centers with a push pin. Next, place this template over the
desired area and mark with the push pins. Install screws (user supplied) into the marks until ¼ in. (0.6
cm) of the screw heads are exposed. Mount the surge suppressor over the screw heads and slide into
place.

Connect Your Surge Suppressor to the AC Power Line: Plug the surge suppressor’s power cord
into a standard, 3-wire grounded 120V AC outlet.

Turn Your Surge Suppressor ON: Press the surge suppressor’s power switch to “ON” or “RESET”
(depending on model). Select models feature an illuminated switch.

Check Your Surge Suppressor’s Diagnostic Indicator Lights (Available on Select Models Only):

If your surge suppressor features diagnostic LEDs, check them prior to connecting your equipment.
They will indicate various operating conditions when the surge suppressor is plugged into a live 120V
AC outlet and the surge suppressor’s power switch is on.

“PROTECTED” LED: Indicates the surge suppression components are intact and providing
complete protection against surges. If this LED does not illuminate, some of the surge suppression
components are not functioning, and the unit should be replaced. Visit www.tripplite.com/support.

“GROUNDED” LED: Indicates wall outlet is grounded and surge protection can properly
function. If this light DOES NOT illuminate and power is present, consult a qualified electrician to
examine your outlet’s wiring.

“GROUNDED” LED (STIK and SUPER8 only): Indicates wall outlet is grounded and surge
protection can properly function. If this light ILLUMINATES and power is present, consult a
qualified electrician to examine your outlet's wiring.

“LINE OK” LED (select models): Indicates 120V AC power is present with no wiring faults
detected.

Connect Your Equipment to the Surge Suppressor’s AC Outlets: Plug your equipment’s power
cords (including 2-wire devices) into the surge suppressor’s AC outlets. Select models feature
integrated safety covers which cover the outlets when not in use. Other models feature special widely­spaced outlets to accommodate transformers without covering other outlets. DO NOT plug in
extension cords. DO NOT OVERLOAD the surge suppressor’s outlets. The surge suppressor can
accommodate a total equipment load of up to 15 amps (whether plugged into a single outlet or spread
out over multiple outlets). If the load on the surge suppressor exceeds 15 amps, the circuit breaker*
will trip and the outlets will stop providing power. If the circuit breaker trips, reduce the load by
unplugging some devices. Depress the circuit breaker to reset.

* Circuit breakers are integrated into the power switch on select models and offered as a separate feature on other models.

2

201010194 93-2666.indd 2 11/12/2010 9:36:52 AM

Installation (continued)

Connect Your Equipment to the Surge Suppressor’s Phone Jacks (Optional Installation.
Available on Select Models Only): Connect a phone cable from the wall jack directly to the surge

suppressor’s RJ-style phone jack labeled “IN.” Connect a phone cable from the surge suppressor’s
RJ-style phone jack labeled “OUT” directly to the device to be protected. Select models feature two
“OUT” jacks; either one or both of the jacks may be used, but protection is for a device or devices
sharing a single line only. All models with phone line surge protection, except the TLP810NET, protect
devices on a single line only. TLP810NET models feature a single set of RJ-style phone jacks which
protect devices on two lines. The surge suppressor must always be the first item connected in line from
the wall jack. The surge suppressor must be plugged into a 3-wire, grounded AC outlet for phone line
surge protection to work.

Connect Your Equipment to the Surge Suppressor’s Network Jacks* (Optional Installation.
Available on Select Models Only): Connect a data cord from the wall jack or cable/DSL modem

directly to the surge suppressor’s network jack labeled “IN.” Connect a data cord from the surge
suppressor’s network jack labeled “OUT” directly to the device to be protected (typically a computer’s
network interface card).

The surge suppressor must always be the first item connected in line from the Ethernet source
(typically a wall jack). The surge suppressor must be plugged into a 3-wire grounded AC outlet for
network line surge protection to work.

Connect Your Equipment to the Surge Suppressor’s Coaxial Jacks (Optional Installation.
Available on Select Models Only): Connect a coaxial cable from the wall jack directly to the surge

suppressor’s “F” style coaxial jack labeled “IN.” Connect a coaxial cable from the surge suppressor’s
“F” style coaxial jack labeled “OUT” directly to the device to be protected. Select models include a
second set of coaxial jacks for simultaneous connection and protection of devices on two separate lines
(cable, antenna or satellite). The surge suppressor must always be the first item connected in line from
the coaxial wall jack. The surge suppressor must be plugged into a 3-wire grounded AC outlet for
coaxial line surge protection to work.

* 10/100 BaseT/TX, Token Ring. Not compatible with PoE (Power Over Ethernet) applications.

FCC Part 68 Notice (United States Only)

If your Modem/Fax Protection causes harm to the telephone network, the telephone company may temporarily discontinue your service. If possible,
they will notify you in advance. If advance notice isn't practical, you will be notified as soon as possible. You will be advised of your right to file a
complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operations or procedures that could affect the
proper operation of your equipment. If it does, you will be given advance notice to give you an opportunity to maintain uninterrupted service. If you
experience trouble with this equipment's Modem/Fax Protection, please visit www.tripplite.com/support for repair/warranty information. The
telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure the equipment
is not malfunctioning. There are no repairs that can be made by the customer to the Modem/Fax Protection. This equipment may not be used on
coin service provided by the telephone company. Connection to party lines is subject to state tariffs. (Contact your state public utility commission
or corporation commission for information.)

Lifetime Limited Warranty

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship
for its lifetime. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its
sole discretion. Service under this Warranty can only be obtained by your delivering or shipping the product (with all shipping or delivery charges
prepaid) to: Tripp Lite, 1111 W. 35th St., Chicago, IL 60609. Seller will pay return shipping charges.

The warranties of all TRIPP LITE surge suppressors are null and void if they have been connected to the output of any UPS system. The warranties
of all TRIPP LITE UPS Systems are null and void if a surge suppressor has been connected to its output receptacles.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER
MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION
TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL
DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights,
and you may have other rights which vary from jurisdiction to jurisdiction.)

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended.
Since individual applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of
these devices for any specific application.

The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.

3

201010194 93-2666.indd 3 11/12/2010 9:36:52 AM

Lifetime Limited Warranty (continued)

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The
series number can be found on the product nameplate label, along with all required approval markings and information. When requesting
compliance information for this product, always refer to the series number. The series number should not be confused with the marking name or
model number of the product.

Warranty Registration

Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You'll be automatically entered
into a drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

Ultimate Lifetime Insurance Policy

(This is a limited warranty valid in the U.S. and Canada only.)

Tripp Lite warrants, for the lifetime of the product, (at Tripp Lite's option) to repair or replace (on a pro rata basis) directly connected equipment
that is damaged due to power transients while properly connected to Tripp Lite products offering the Ultimate Lifetime Insurance Policy. Power
transients include spikes and surges on the AC power, data or telephone lines that the Tripp Lite products have been designed to protect against
(as recognized by industry standards). The following four paragraphs are conditions that must be complied with before the warranty becomes
valid; failure to comply with these requirements will void the warranty.

AC Power Line Transients: To claim damages, the Tripp Lite product must be plugged into a properly wired and grounded outlet. No extension cords
or other electrical connections may be used. The installation must comply with all applicable electrical and safety codes set forth by the National
Electrical Code (NEC). Except as provided above, this warranty does not cover any damage to properly connected electronic equipment resulting
from a cause other than an "AC power transient". If user meets all of the above requirements, Tripp Lite will repair or replace (at Tripp Lite's option)
equipment up to the specified value (See Ultimate Lifetime Insurance Policy Limits). No coverage is allowed for damage entering from telephone
or data lines, unless they are separately protected, as described below.

Telephone and Data Line Transients: Tripp Lite will repair or replace directly connected equipment that is damaged by transients on telephone and/
or data lines only when all such paths are protected by a Tripp Lite protection product(s) and the AC power (utility) line is simultaneously protected
by a Tripp Lite power protection device (UPS, surge suppressor or line conditioner) with Ultimate Lifetime Insurance coverage. Additional telephone
and/or data line connected devices downstream must have their own telephone and/or dataline protectors.

Reimbursement dollar limits will be equal to that of the Tripp Lite power protection protector. Coverage is excluded where a suitable environment
for the protection device is not provided, including, but not limited to, lack of a proper safety ground. Telephone service equipment must also
include a properly installed and operating "primary protection" device at the telephone service entrance (such devices are normally added during
telephone line installation).

All above warranties are null and void if the Tripp Lite product has been improperly installed, tampered with or altered in any way, or if the connected
equipment was not used under normal operating conditions or in accordance with any labels or instructions. All claims under this warranty must
be submitted in writing to Tripp Lite within 30 days of the occurrence or the claim will not be considered. This warranty does not include damage
resulting from accident or misuse, and applies to the domestic (USA & Canada) use of these products only. Tripp Lite reserves the right to
determine whether the damage to the connected equipment is due to malfunction of the Tripp Lite product by requesting the equipment in question
be sent to Tripp Lite for examination. This policy is above and beyond, only to the extent needed, of that provided by any coverage of connected
equipment provided by other sources, including, but not limited to, any manufacturer's warranty and/or any extended warranties.

EXCEPT AS PROVIDED ABOVE, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid
limitation(s) or exclusion(s) may not apply to purchaser. EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT,
INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE. Specifically, Tripp Lite is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use
of equipment, loss of software, loss of data, costs of substitutes, claims by third parties or other wise. Coverage also does not apply to connected
medical and industrial equipment.

To receive service under this warranty, you must be the original purchaser/user of the product in question. You must obtain a Returned Material
Authorization (RMA) number from Tripp Lite. Products must be returned to Tripp Lite with transportation charges prepaid and must be accompanied
by a brief description of the problem encountered and proof of date and place of purchase.

1111 W. 35th Street Chicago, IL 60609 USA

www.tripplite.com/support

201010194 • 932666-EN

4

201010194 93-2666.indd 4 11/12/2010 9:36:53 AM