Tripp Lite SmartOnline SU6K, SmartOnline SUIOK, SmartOnline SU10K Owner's Manual

SmartOnline

1111 W. 35th Street

Chicago, IL 60609 USA

Customer Support: [phone]

Application Services: [phone]

www.tripplite.com

Safety: p. 2

Control Panels: p. 3 - 5

On-Line, Extended-Run UPS Systems

Owner's Manual

TM

• SU6K (6kVA)

• SU10K (10kVA)

ESPAÑOL: p. 18

FRANÇAIS: p. 35

Installation: p. 6 - 9

Operation: p. 9 - 12

Communications: p. 13 - 14

Service: p. 15

Warranty & Insurance: p. 15

Function Block Diagram: p. 16

Specifications: p. 17

Copyright © 2001 Tripp Lite. All rights reserved. SmartOnlineTM is a registered trademark of Tripp Lite.

1

Safety

This manual contains important instructions and warnings that should be followed
during the installation, operation and storage of all Tripp Lite SmartOnline UPS
Systems.

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, dust or direct
sunlight.

• Install your UPS in a structurally sound area. Your UPS is extremely heavy; take
care when moving and lifting the unit.

• Only operate your UPS at indoor temperatures between 32° F and 104° F (between
0° C and 40° C). For best results, keep indoor temperatures between 62° F and
84° F (between 17° C and 29° C).

• Leave adequate space around all sides of the UPS for proper ventilation: 12 in. (30
cm.) clearance at the rear; 4 in. (10 cm.) at sides and on top.

• Do not install the UPS near magnetic storage media, as this may result in data
corruption.

UPS Connection Warnings

• The power supply for this unit must be single phase rated in accordance with the
equipment nameplate. It also must be suitably grounded.

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems in life support applications in which a mal­function or failure of a Tripp Lite UPS System could cause failure or significantly
alter the performance of a life support device.

• Connect your UPS's Grounding Terminal to a grounding electrode conductor.

• The SU6K contains its own energy source (battery). The output terminals may be
live even when the UPS is not connected to an AC supply.

Battery Warnings

• Your UPS does not require routine maintenance. Do not open your UPS for any
reason. There are no user-serviceable parts inside.

• Because the batteries present a risk of electrical shock and burn from high short­circuit current, batteries should be changed only by trained service personnel
observing proper precautions. Replace the existing batteries with the same number
and type of new batteries [(Sealed Lead-Acid) SU6K (twenty 12V/7AH batteries);
SU10K (forty 12V/7AH batteries)]. Do not open the batteries. Do not short or
bridge the battery terminals with any object.

• The UPS batteries are recyclable. Refer to local codes for disposal requirements, or
if in the USA call 1-800-SAV-LEAD (1-800-728-5323) for complete recycling
information. Do not dispose of the batteries in a fire.

• Connect only Tripp Lite battery packs to your UPS’s external battery connectors.

• Do not operate your UPS without batteries.

• Fuses should be replaced only by factory authorized personnel. Blown fuses

should be replaced only with fuses of the same number and type.

• Potentially lethal voltages exist within this unit as long as the battery supply is

connected. Service and repair should be done only by trained personnel. During
any service work, the UPS should be turned off or put into manual bypass (see pg.

12).

• During “hot-swap” battery replacement (when the UPS is on manual bypass and
connected equipment is turned ON) your UPS will be unable to provide battery
backup in the event of a blackout.

• Do not connect or disconnect the battery cabinets while the UPS is operating from
the battery supply or when the unit is not in bypass mode.

2

Control Panels

Familiarize yourself with the location and function of the front and rear panel
features before installing and operating your UPS.

FRONT PANEL

3

4 5 6 7

1. “ON/OFF” Switch: This momentary rocker switch turns the UPS System’s inverter

ON and OFF.

2. “SELECT” Button: This button performs two functions: it allows you to browse

through different power readings on the LCD Display by momentarily pressing the
button; it also allows you to silence the UPS alarm by pressing and holding the button
for 3 seconds.

9

8

12

3. LCD Display: This backlit (16x2 character) dot matrix display indicates a wide range

of UPS operating conditions and diagnostic data. It will illuminate after you have
properly completed installation and start-up and after the “ON/OFF” Switch is turned
ON.

4. “I/P” (Input) LED: This green light will illuminate constantly to indicate an AC input

supply is present.

5. “AC/DC” (Converter) LED: This green light will illuminate constantly to indicate the

UPS’s AC/DC converter is activated.

6. “DC/AC” (Inverter) LED: This green light will illuminate constantly to indicate the

UPS’s DC/AC inverter is activated.

7. “O/P” (Output) LED: This green light will illuminate constantly to indicate your UPS

is supplying AC power to connected equipment.

8. “BYPASS” LED: This green light will illuminate when the UPS is providing filtered

mains power without engaging its converter or inverter. Connected equipment will not
receive battery power in the event of a blackout.

9. “BATTERY” LED: This red light will illuminate when the UPS is discharging the

battery to provide connected equipment with AC power. An alarm will sound which
can be cancelled by pressing and holding the “SELECT” switch for 3 seconds. The
alarm will be cancelled, but the LED will remain illuminated.

3

Rear Panels

5

16

ON LINE
MODE
ECONOMY
MODE

10

11

8

6

7

12

9

15
17

1

5

13

2

14

3

4

18

SU10KBP

SU10KPM

11

ON LINE
MODE
ECONOMY
MODE

16

10

8
7

2

5

12

5

6

17

1

9

15

5

12

SUBP

4

13

14

2
4

L1 L2

3

18

SU6K

REAR PANELS

1. Manual Bypass Switch: This red and yellow dial is used in one step of putting the UPS

in "BYPASS” mode, which must be done before performing any maintenance on the UPS
with the connected load supported. (See page 12 for step-by-step instructions for going
into "BYPASS.") While this switch is on "BYPASS," connected equipment will receive
filtered AC mains power, but will not receive battery power in the event of a blackout.

2. Input Terminal Block: Use these terminals to connect your UPS to the AC main

power input. Unscrew and remove terminal block plate for access. The optional SUBP
battery pack's IEC-320 connector accepts its charger's input power cord.

3. Output Terminal Block: Use these terminals to connect your UPS to equipment.

A plate covering the terminal block must be unscrewed and removed for access.

4. Input Voltage Select Terminal Block: Use these terminals to set your UPS's to

receive your 208V AC or 240V AC line voltage. A plate covering the terminal block
must be unscrewed and removed for access.

5. External Battery Connector: Use this to connect Tripp Lite Battery Packs. The

SU10K requires a SU10KBP or SUBP to operate; additional SUBP's can be added to
SU6K or SU10K systems for extra runtime. Refer to instructions available with the
optional SUBP Battery Pack for connection instructions and safety warnings.

6. Exhaust Fan: This cools and ventilates the inside of the UPS.

7. AS-400 Interface Port: This female DB9 port connects your UPS to an IBM AS-400

computer interface via the AS-400 Cable included. It uses AS-400 communications
to report UPS status and power conditions. Using this port, an IBM AS-400 computer
can automatically save open files and shut down its operating system during a
blackout. See "Communications," pg. 13, for details.

8. “Smart” RS-232 Interface Port: This female DB9 port connects your UPS to a

workstation or server. It uses RS-232 communications to report UPS and power
conditions. It is used with Tripp Lite software and the included RS-232 Cable to
monitor and manage network power and to automatically save open files and shut
down equipment during a blackout. See "Communications," pg. 13, for details.

9. Dry Contact Interface Port: This female DB9 port sends contact-closure signals to

indicate line-fail and low-battery status. See "Communications," pg. 14, for details.

10. Accessory Slot: Remove the small cover panel and use optional accessories

to remotely control and monitor your UPS. Contact Tripp Lite Customer Support for
more information and a list of available SNMP, network management and connec­tivity products.

11. “Battery Start” Switch: This momentary rocker switch allows you to “cold-start” your

UPS and use it as a stand-alone power source when utility-supplied AC power is not
present. The switch enables the UPS’s DC/AC Inverter. Before “cold-starting” your
UPS, make sure your UPS and external battery cabinets are properly installed. Press
and hold the “Battery Start” Switch and then press the “ON/OFF” switch to turn your
UPS ON. To turn it OFF after “cold-start,” press the “ON/OFF” Switch.

12. Battery Fuses (SU6K & SUBP's Only): The 30A/600V fuses protect your connected

battery or battery bank.

13. AC Input Breakers: One double-pole circuit breaker controls input power to the UPS.

14. AC Output Breaker: Triple-pole circuit breakers control output power from the UPS.

15. Remote “Emergency Power OFF” Connector: This RJ11 modular jack allows

remote emergency shutdown. See "Communications," pg. 14, for details.

16. Inverter Operation DIP Switches: Behind this removable panel are four DIP

Switches that should be set to match your input voltage and input frequency. Your
input voltage and frequency DIP switch settings MUST match your input. Your UPS
WILL NOT CONVERT the voltage or frequency.

17. Grounding Terminal: This terminal connects to a grounding electrode conductor.

IT IS NOT SAFE TO OPERATE YOUR UPS WITHOUT CONNECTING IT. The
recommended conductor size is 8 AWG based on the UL 1778 standard.

18. Stabilizers: These supports extend to keep your UPS from rolling or tipping.

5

Installation

1 2 3 4

INVERTER OPERATION DIP SWITCH

ON LINE
MODE
ECONOMY
MODE

SETTINGS (SU10KPM SHOWN)

Using a small tool, set the four Inverter Opera­tion DIP Switches (located on the rear panel of
your UPS, see pg. 4-5 for location) to match
your input voltage, input frequency and
desired operational mode.

Input Voltage Selection

(DIP Switches #1 & #2)

(Input Voltage Select Terminal Block)

These DIP switches and the Input Terminal
Select Block must BOTH be set to match your
input voltage. Your UPS WILL NOT CONVERT
the voltage.

Input Voltage

Input Voltage DIP Switch Position Select Terminal Block

208V #1 UP & #2 UP

208V

240V #1 DOWN & #2 DOWN

240V

Input Frequency Selection

(DIP Switch #3)

Your Input Frequency setting MUST match your input frequency. Your UPS WILL NOT
CONVERT the frequency.

Input Frequency DIP Switch Position

50 Hz #3 UP

60 Hz #3 DOWN

Operational Mode Selection

(DIP Switch #4)

The "On-Line" Mode provides on-line operation with zero transfer time. The "Economy"
Mode provides line-interactive operation for increased efficiency when on-line protection
is unnecessary, thus reducing operating costs without affecting your UPS's output
reliability during a power outage.

Input Frequency DIP Switch Position

On-Line #4 UP

Economy #4 DOWN

6

UPS LOCATION

Move your UPS over short distances using its wheels. Stabilize the UPS by releasing the
stabilizers on each side of the unit. NOTE: Do not stack the UPS Systems or external
battery packs.

INPUT AND OUTPUT CONNECTION

WIRING SELECTION

Choose appropriate cabling (depending on current carried; see chart below) to connect
your UPS to an AC power supply and your equipment to your UPS:

MODEL RATED INPUT RATED OUTPUT RATED OUTPUT OUTPUT

SU6K 30A 8 AWG (8mm

SU10K 50A 6 AWG (14mm

WIRING CONNECTIONS

Connect your wiring to the input and output terminal blocks located on the lower rear
panel of your UPS (see figure below). Before cable connection, turn the UPS OFF and pull
out the fuse holder. Ensure the cable is fitted with a cable sleeve and is secured by a
connector clamp. The minimum tightening torque is 35 lbs. per square inch. Connect
the ground wire (typically colored green and yellow) to the terminal marked with the
letter "G."

CURRENT CURRENT CURRENT PROTECTION

208/240 1Ø 3 Wire 120-208/240V 1Ø 3 Wire 120V 1Ø 3 Wire CIRCUIT

2

/60oC) 30A 8 AWG (8mm2/60oC) 2 x 32A 6 AWG (14mm2/60oC) 32A

2

/60oC) 50A 6 AWG (14mm2/60oC) 2 x 50A 4 AWG (22mm2/60oC) 63A

Cable Connection for 6kVA or 10kVA Output (6kVA shown)

CAUTION: Observe the appropriate
cable connection regulations [e.g.
National Electrical Code (NEC) in
the U.S.] at all times. Using cables
of improper size may damage your
equipment and cause fire hazards.
Ground the UPS and the load
equipment as shown in the figure.

TO THE BUILDING

EARTH

(GROUND)

GROUND

CONNECTION

LOAD 1

UPS

LOAD 2

LOAD 3

7

EXTERNAL BATTERY PACK CONNECTION

(SU6K: Optional; SU10K: Required)

Since SU6K models contain internal batteries, connecting external battery packs (to
extend runtime) is optional. SU10KPM models, however, do not have internal batteries
and require an external battery pack connection to a SU10KBP or a SUBP. Using the
supplied battery connection cable, insert one end into the External Battery Connector
on the rear panel of your UPS and the other end into the Battery Output Connector on
the rear panel of the external battery pack. Use the plug on either end of the supplied
cable, but make sure that it is fully inserted into the connector. See figure below for
daisy-chaining one or more external battery packs to your UPS.

ON LINE
MODE
ECONOMY
MODE

SUBP SU10KBP SU10KPM

Note: Optional Tripp Lite external battery packs (SUBP's) feature individual 120V AC
input line cords and individual internal battery chargers. By adding multiple SUBP's
individually connected to 120V AC input, the recharge time of a battery system will be
dramatically reduced as compared to systems relying on only the UPS's main charger.
While adding SUBP's without connecting their chargers will increase a battery system's
reserve capacity, this will also
increase the system's overall
recharge time. See the figure to the
right for the schematic diagram of
the SUBP external battery pack.

BATTERY FUSE
REPLACEMENT

AC INPUT

120VDC

THE DIAGRAM OF THE EXTENSIBLE BATTERY CABINET

FUSE

CHARGER

20PCS

12V/7Ah

If one of your fuses has blown, you will
notice no output voltage at zero load. Blown
fuses should be replaced as shown in the
diagram on the right. Since SU6K models
contain internal batteries, the battery fuse
holders are located on the rear panel of the

press down
thelatch bar to open

insert th e fuse

UPS. Since SU10K models operate solely
from external batteries, the battery
fuse holders are located on the rear panel of the external battery pack(s). Note: SU6K
models also support connections to optional external battery packs, which may require
battery fuse replacement.

20PCS
12V/7Ah

fus e

fus e

fus e

fus e

close the latch bar

G

G

DC IN PUT

240VDC

DC OUTPUT

240VDC

8

BATTERY CONDITION VERIFICATION

When the UPS is operating from battery power, the alarm and LCD Display will both alert
you to the UPS battery’s charge condition.

Battery Charge Condition Alarm LCD Display

FULL Short Beep (every 2 seconds) ON BATTERY

LOW Short Beep (every 1/2 second) BATTERY LOW

UNDER Continuous Beep BATTERY UNDER

INITIAL BATTERY CHARGING (OPTIONAL)

Your UPS System’s battery is fully charged prior to shipping. However, if your UPS has
been stored for an extended period, recharge its battery for 8 hours. To charge, turn
on the AC Input Breaker. The LCD Display will illuminate and indicate “ON BYPASS.”
DO NOT turn on the AC Output Breaker to apply the load until the battery is fully
charged. Once the UPS is in use, it will charge the batteries and maintain the charge
level automatically.

Operation (Normal Conditions)

BATT = XXV XX%

BATT = XXV XX%

SHUT DOWN

TURNING THE UPS ON

• Make sure the UPS is properly installed (see Installation section) and the Manual
Bypass Key is set to NORMAL.

• Turn the AC Input Circuit Breaker ON, then turn the Output Circuit Breakers ON.

• If your AC input is providing power normally within your selected range (see Input
Voltage Selection, pg. 6, and Specs, pg. 17), your connected load will energize.
However, the UPS's inverter is not yet on. Press the front "ON/OFF" switch ON to
begin inverter operation.

• If your AC input is not providing power normally, you have the option of starting
from battery. (Your battery must be at least partially charged for this operation to
succeed.) Press and hold both the "Battery Start" switch and the "ON/OFF" switch
for three seconds to start your UPS in "ON BATTERY" mode. Note that some
electronic equipment may draw more amps during startup; when starting from
battery, consider reducing the initial load on the UPS.

• The UPS will perform a brief self-test and show the results on the LCD Display. (See
Self-Test section, pg. 10, for display sequence.) After a successful self-test, the UPS
will provide AC power from the inverter to your load.

TURNING THE UPS OFF

• Press the front “ON/OFF” Switch OFF. Your load will still be energized. The inverter
is now off, but your UPS is not fully deactivated. The LCD Display will show “ON
BYPASS."

• Turn the AC Input and Output Circuit Breakers OFF. Your load will no longer be
energized, and the LCD display will be dark.

9

SELF-TESTING

When you turn the UPS ON, it will perform a brief (about 25 second) self-test. See figure
below for display sequence.*

*Note: If starting from battery, the BATTERY LED will be lit and the I/P and BYPASS LEDs will not. The final LCD display in the
diagram below appears when the UPS is operating normally under utility-supplied AC input power.

FREQ OUT = XXHz

INPUT AC OK

BATTERY OK

CHARGER OK

AC/DC OK

WAITING
INVERTER TEST

OR

OR

OR

BAD BATTERY
CALL FOR SERVICE

CHARGER FAILURE!
CALL FOR SERVICE

AC/DC FAILURE!
CALL FOR SERVICE

10

ON INVERTER
LOAD = XXX% X.XXKW

LCD DISPLAY SELECT SWITCH

Momentarily press the “SELECT” switch on the front panel to browse through different
power readings on the LCD Display. The LCD Display will show which one of four
operational modes your UPS is currently in: Normal, Economy, On-Battery, or Bypass.
Also, as you press the “SELECT” switch, the LCD Display will browse through load, input,
bypass, output and battery conditions.

"NORMAL" MODE OPERATION "ON-BATTERY" MODE OPERATION

ON INVERTER

ON INVERTER

LOAD=XXX% X.XXKW

LOAD = XXX% X.XXKW

PRESS SELECT KEY

ON INVERTER

ON IN VERTE R

IN=XXXV XX.XHz

IN = XXXV XX.XHz

PRESS SELECT KEY

ON INVERTER

ON INVERTER

OUT=XXXV XX.XHz

OUT = XXXV XX.XHz

PRESS SELECT KEY

ON INVERTER

ON INVERTER

BATT=XXXV XXX%

BATT = XXXV XXX%

PRESS SELECT KEY

"ECONOMY" MODE OPERATION "ON BYPASS" MODE OPERATION

ON BATTERY

ON BATTERY

LOAD=XXX% X.XXKW

LOAD = XXX% X.XXKW

PRESS SELECT KEY

ON BATTERY

ON BATTERY

IN=XXXV XX.XHz

IN = XXXV XX.XHz

PRESS SELECT KEY

ON BATTERY

ON BATTERY

OUT=XXXV XX.XHz

OUT = XXXV XX.XHz

PRESS SELECT KEY

ON BATTERY

ON BATTERY

BATT=XXXV XXX%

BATT = XXXV XXX%

PRESS SELECT KEY

ECONOMY MODE

ECONOMIC MODE

LOAD = XXX% X.XXKW

LOAD=XXX% X.XXKW

PRESS SELECT KEY

ECONOMY MODE

ECONOMIC MODE
IN = XXXV XX.XHz

IN=XXXV XX.XHz

PRESS SELECT KEY

ECONOMY MODE

ECONOMIC MODE

OUT = XXXV XX.XHz

OUT=XXXV XX.XHz

PRESS SELECT KEY

ECONOMY MODE

ECONOMIC MODE

BATT=XXXV XXX%

BATT = XXXV XXX%

PRESS SELECT KEY

Operation (Special Conditions)

OPERATION ON BYPASS—VOLTAGE OUT OF RANGE

While in Bypass Mode, the UPS monitors the input voltage, which on Bypass equals the
output voltage. If the output voltage passes out of an acceptable range (between 15% higher
and 20% lower than nominal), the UPS displays the condition on its LCD and stops
supplying output power to its load. If power levels return to an acceptable level, the UPS
resumes supplying power to the load, and its LCD reports that output voltage was too high
or too low at one time, but has returned to nominal.

Bypass Voltage Condition LCD Display Message

>15% Higher than Nominal BYPASS AC TOO HI

>20% Lower than Nominal BYPASS AC TOO LO

Was Too High, Now Nominal BYPASS AC WAS HI

Was Too Low, Now Nominal BYPASS AC WAS LO

ON BYPASS

ON BYPASS

LOAD=XXX% X.XXKW

LOAD = XXX% X.XXKW

PRESS SELECT KEY

ON BYPASS

ON BYPASS

BYPS = XXXV XX.XHz

BYPS=XXXV XX.XHz

PRESS SELECT KEY

ON BYPASS

ON BYPASS

OUT=XXXV XX.XHz

OUT = XXX V XX.XH z

PRESS SELECT KEY

OPERATION ON OVERLOAD

When the UPS detects an output overload, it will commence a countdown (the length of
time depending on the severity of the overload). If the UPS is still overloaded at the end
of the countdown, the UPS will automatically shut down and go into Bypass Mode.

Overload Condition LCD Display Message Countdown to Shutdown

102% - 125% Overload 102% 1 minute

125% - 150% Overload 125% 30 seconds

>150% Overload 150% 2 seconds

Load=XXX% X.XXKW

Load=XXX% X.XXKW

Load=XXX% X.XXKW

11

BATTERY CHARGE WARNINGS

Since your UPS can provide battery backup only for as long as the batteries remain
charged, these warnings should be acted on immediately.

Battery Charge Warning LCD Display Message

Battery charge nearly depleted BATTERY LOW

AC/DC charger not operating CHARGER FAILURE!

OPERATION UNDER SHUTDOWN

Your UPS will shut down and the LCD will display a message if it detects one of the
following conditions. Note: For all conditions, the “Input,” “Output” and “Bypass” LEDs
will be illuminated.

Condition LCD Display Message

Extended Overload (>150%) OVERLOAD 150%

SHUT DOWN

Output Short Circuit SHORT CIRCUIT!

SHUT DOWN
Remote Shutdown Command REMOTE
(FROM DB9 INTERFACE) SHUT DOWN
Remote Shutdown Command EMERGENCY STOP!
(from RJ11 interface) SHUT DOWN

Internal Faults INVERTER TOO LO

SHUT DOWN

INVERTER TOO HI

SHUT DOWN

DC BUS +/- HIGH/LOW

SHUT DOWN

OVERTEMPERATURE

SHUT DOWN

OPERATION OF MANUAL BYPASS SWITCH

Turn this switch to “BY­PASS” before performing
any maintenance on the
UPS with the connected
load supported. Connected

AC INPUT

UPS

INPUT BREAKER

equipment will receive
filtered AC mains power,
but will not receive
battery power in the event

¡¸LONG BACK-UP

SUBP CHARGER OUTPUT

TIME CHARGER

STD.

BATTERY

BATTERY

CABINET

of a blackout.

SWITCHING UPS TO “BYPASS” MODE

• Turn the “ON/OFF” Switch OFF. (LCD will read "ON BYPASS.")

• Turn the “Manual Bypass” Switch clockwise from NORMAL to BYPASS.

• Turn the AC Input Circuit Breaker OFF.

• Open battery fuse holders and remove the battery fuses from all battery packs
and from all SU6K models.

SWITCHING UPS TO “NORMAL” MODE

• Replace all battery fuses in the battery fuse holders and close the
battery fuse holders.

• Turn the AC Input Circuit Breaker ON.

• Turn the “Manual Bypass” Switch counterclockwise from BYPASS
back to NORMAL.

• Turn the “ON/OFF” Switch ON.

MANUAL BYPASS SWITCH

UPS POWER

¡¸ LONG BACK-UP TIME MODELS CONTAIN LONG BACK-UP TIME CHARGE

SUBP CONNECTED MODELS CONTAIN SUBP CHARGER

¡¸ IN THE CONFINED AREA, ALL COMPONENTS ARE ELECTRIC ISOLATIO N

CURRENT IN THE AREA MARKED BY THE DASHED

W ITH AC LINE

OUTLINE. ALL COMPONENTS ARE ELECTRONICALLY
ISOLATED FROM THE AC LINE.

OUTPUT BREAKER

OUTPUT

12

Communications

RS-232 INTERFACE

This female DB9 port connects your UPS via an RS-232 cable to a workstation or server
equipped with Tripp Lite software. The port uses RS-232 communications to report UPS
status and power conditions. Using this port, Tripp Lite software can monitor and
manage network power and automatically save open files and shut down equipment
during a blackout. Contact Tripp Lite Customer Support at [phone] for informa­tion on available SNMP, network management and connectivity software and products.

RS-232 signals and operations include: load level, battery status, battery level,
operation mode, AC input voltage, AC output voltage, AC input frequency, temperature
inside unit, set shut-down delay time, enable/disable alarm and remote shutdown.

Hardware:
Baud Rate: 2400 BPS
Data Length: 8 bits
Stop Bit: 1 bit
Parity: NONE

AS-400 INTERFACE:

This female DB9 port connects your UPS to an IBM AS-400 computer via the included
AS-400 cable. The port uses AS-400 communications to report UPS status. It can be used
to allow an AS-400 to automatically save open files and shut down its operating system
during a blackout. AS-400 protocol includes: operation on inverter, operation on AC
power supply, operation on battery and low battery alarm.

Pin assignment:

Pin 2: TXD (Transmit Data)
Pin 3: RXD (Receiving Data)
Pin 5: GND (Signal Ground)

Pin assignment:

Pin 5: Common
Pin 6: Operation on AC power supply
Pin 7: Low battery alarm
Pin 8: Operation on inverter
Pin 9: Operation on battery

LOW BATTERY

BATTERY

BACK-UP

DIRECT MAINS

SUPPLY

INVERTER

AS-400 INTERFACE TABLE

Pin 6,5 Pin 7,5 Pin 8,5 Pin 9,5

1

6

2

7

3

8

4

9

5

Battery OFF * ON ON

Low Battery OFF ON ON ON

Direct Mains Supply ON OFF OFF OFF

Inverter OFF * ON *

* Inactive: may be in either state.

13

DRY CONTACT INTERFACE:

U

X

This female DB9 contact-closure port allows your UPS to send contact-closure signals
to indicate that it is on battery back-up mode and if its batteries are running low. The
port can also receive a remote shutdown signal.

Pin assignment:

LOW BATTER Y

NO

NCCOM

MAXIMUM CAPACITY OF DRY CONTACT:

THE MAXIM UN CAPACITY OF DRY CONTACT:

AC 250V/3A
DC 30V/3A

AC 250V/3A
DC 30V/3A

BACK-UP

NO

THE SIGHAL

SIGNAL FROM
COMPUTER

FROM COM PU TER

NCCOM

DRY CONTACT INTERFACE TABLE

UPS Operating Pin 8,3 Pin 1,3
Mode

Normal OPEN OPEN

Back Up CLOSE *

Low Battery CLOSE CLOSE

Im in.>3 .3m A

REMOTE SHUTDOWN SIGNAL

THE REM OTE SH

FROM EXTERNAL

SIGNAL FROM E

>2 sec

12 V

¡Ó3V

0

* Inactive: may be in either state.

REMOTE EMERGENCY POWER OFF:

This RJ11 modular jack allows remote emergency shutdown.

Pin assignment (SU6K Shown)

ON LINE
MODE
ECONOMY

12V

1

X

2

3

1K

4

5

6

X

If there is a short between pins 2 and 3, 2 and 5, 4 and 5, or 3 and 4, the UPS will
power off.

MODE

Pin 1

14

Service

Service

Your SmartOnline UPS is covered by the 2-year limited warranty period described
below. A variety of service contracts is also available from Tripp Lite, including start­up service contracts and 3- to 5-year SafeSure on-site service contracts. For more
information, call Tripp Lite Customer Service at [phone].

Warranty & Insurance

2-Year Limited Warranty

TRIPP LITE warrants its products including batteries to be free from defects in materials and workmanship for a period of two years from the
date of initial purchase. After 90 days from the date of purchase, TRIPP LITE’s obligation under this warranty is limited to replacing parts on
such defective products. To obtain service under this warranty, you must call TRIPP LITE or an authorized TRIPP LITE service center. Products
must be returned to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid and must be accompanied by
a brief description of the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment which has
been damaged by accident, negligence or misapplication or has been altered or modified in any way. This warranty applies only to the original
purchaser who must have properly registered the product within 10 days of purchase.

The warranties of all TRIPP LITE surge suppressors are null and void if they have been connected to the output of any UPS system. The warranties
of all TRIPP LITE UPS Systems are null and void if a surge suppressor has been connected to its output receptacles.

EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties;
therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Specifically, TRIPP LITE is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software,
loss of data, costs of substitutes, claims by third parties, or otherwise.

The policy of TRIPP LITE is one of continuous improvement. Specifications are subject to change without notice.

Ultimate Lifetime Insurance Policy
(Valid in U.S. and Canada ONLY)

TRIPP LITE warrants, for the lifetime of the product, (at TRIPP LITE's option) to repair or replace (on a pro rata basis) directly connected
equipment that is damaged due to power transients while properly connected to TRIPP LITE products offering the ULTIMATE® Lifetime
Insurance Policy. Reimbursement or restoration for data loss is not included. Power transients include spikes and surges on the AC power,
data or telephone lines that the TRIPP LITE products have been designed to protect against (as recognized by industry standards).

AC Power Line Transients: To claim damages, the TRIPP LITE product must be plugged into a properly wired and grounded outlet. No
extension cords or other electrical connections may be used. The installation must comply with all applicable electrical and safety codes set
forth by the National Electrical Code (NEC). Except as provided above, this warranty does not cover any damage to properly connected electronic
equipment resulting from a cause other than an "AC power transient". If user meets all of the above requirements, TRIPP LITE will repair
or replace (at TRIPP LITE's option) equipment up to the specified value (See ULTIMATE® Lifetime Insurance Policy Limits). No coverage is
allowed for damage entering from telephone or data lines, unless they are separately protected, as described below.

Telephone and Data Line Transients: Tripp Lite will repair or replace directly connected equipment that is damaged by transients on telephone
and/or data lines only when all such paths are protected by a Tripp Lite protection product(s) and the the AC power (utility) line is
simultaneously protected by a Tripp Lite power protection device (UPS, surge suppressor or line conditioner) with Ultimate Lifetime Insurance
coverage.

Reimbursement dollar limits will be equal to that of the Tripp Lite power protection product. Coverage is excluded where a suitable
environment for the protection device is not provided, including, but not limited to, lack of a proper safety ground. Telephone service
equipment must also include a properly installed and operating "primary protection" device at the telephone service entrance (such devices
are normally added during telephone line installation).

All above warranties are null and void if the TRIPP LITE product has been improperly installed, tampered with or altered in any way, or if
the connected equipment was not used under normal operating conditions or in accordance with any labels or instructions. All claims under
this warranty must be submitted in writing to Tripp Lite within 30 days of the occurrence or the claim will not be considered. This warranty
does not include damage resulting from accident or misuse, and applies to the domestic (USA & Canada) use of these products only.

Tripp Lite reserves the right to determine whether the damage to the connected equipment is due to malfunction of the Tripp Lite product
by requesting the equipment in question be sent to Tripp Lite for examination. This policy is above and beyond, only to the extent needed,
of that provided by any coverage of connected equipment provided by other sources, including, but not limited to, any manufacturer's
warranty and/or any extended warranties.

EXCEPT AS PROVIDED ABOVE, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties;
therefore, the aforesaid limitation(s) or exclusion(s) may not apply to purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE. Specifically, TRIPP LITE is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss
of software, loss of data, costs of substitutes, claims by third parties or otherwise.

To receive service under this warranty, you must be the original purchaser/user of the product in question. You must obtain a Returned
Material Authorization (RMA) number from TRIPP LITE. Products must be returned to TRIPP LITE with transportation charges prepaid and
must be accompanied by a brief description of the problem encountered and proof of date and place of purchase.

15

BLOCK

OUTPUT

TERMINAL

OUTPUT

BREAKER

XFM

OUTPUT

ISOLATION

BYPASS

SWITCH

MANUAL

LEDS

LCD

TO RS-232

AS-400

DRY CONTACT

ACCESSORY SLOT

REPO

FILTER

OUTPUT

STATIC

SWITCH

BYPASS

INVERTER

DC TO AC

AC TO DC

CONVERTER

INPUT

FILTER

SURGE

PROTECTOR

CPU

CONTROLLER

CHARGER

SUPPLY

POWER

Function Block Diagram

16

BREAKER

AC INPUT

AC INPUT

240 VDC

STANDARD

BATTERIES:

240 VDC

SUBP EXTERNAL

BATTERY CABINET(S):

120 VAC INPUT