Tripp Lite CSC32AC User Manual

Owner’s Manual

Charging Station Cart

32-Outlet Models: CSC32AC (CSC32ACW)

Table of Contents

1. Important Safety Instructions 2

2. Overview 2

3. Feature Identiﬁcation 3

4. Setup 4

4.1 Power Requirements 4

4.2 Installing the Handle Bracket 4 and Power Cord Manager 4

4.3 Adjusting Storage Shelf Dividers 4

4.4 Connecting Devices and 5 Powering the AC Unit

4.5 Door Locks 5

5. Wall Installation 6

5.1 Removing Casters and Handle 6

5.2 Wall-Mounting the Charging Station 6

6. Speciﬁcations 7

7. Storage, Service and Cleaning 7

8. Warranty and Product Registration 8 Español 9 Français 17

PROTECT YOUR INVESTMENT!

You could also win an ISOBAR6ULTRA surge protector—a $100 value!

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

1. Important Safety Instructions

SAVE THESE INSTRUCTIONS

This Manual contains instructions and warnings that must be followed during the installation and operation of the product described in this manual.

Failure to comply may invalidate the warranty and cause property damage or personal injury.

AC Unit:

• To remove the AC unit from the supply mains, the power cord serves as a disconnect device.

• If any of the following situations arise, schedule an appointment to have your equipment inspected by a service technician:

• The equipment has been exposed to moisture

• The equipment has been dropped and damaged

• The equipment shows obvious signs of breakage

• The equipment is not functioning properly or is not functioning according to the instructions described in this Owner’s Manual

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended.

Charging Station Cabinet:

• Keep the charging station in a controlled indoor environment away from moisture, temperature extremes, flammable liquids and gasses, conductive contaminants, dust and direct sunlight.

• Leave adequate space around the charging station for proper ventilation. Do not block, cover or insert objects into the charging station’s external ventilation openings.

• The charging station is extremely heavy. Use caution when handling the charging station. Do not attempt to unpack or mount it unassisted. Use a mechanical device such as a forklift or pallet jack to move the charging station in the shipping container.

• Do not place any object on the charging station, especially containers of liquid, and do not stack items on the cabinet.

• Inspect the shipping container and the charging station for shipping damage. Do not use the charging station if it is damaged.

• Use caution when cutting packing materials. The charging station could be scratched, causing damage not covered by the warranty.

• Save all packing materials for later use. Repacking and shipping the charging station cabinet or equipment without the original packing materials may cause product damage that will void the warranty.

For Mobile Applications:

• The charging station comes with four pre-installed locking/swivel casters.

• Always use the included handle when moving the charging station (see section 4.2 Installing the Handle Bracket and Power Cord Manager for more information).

• When moving the charging station cabinet, always push it from behind; never pull it toward you.

• A rolling charging station can cause personal injury and property damage if not properly supervised. If rolling the charging station down a ramp is required, use extreme caution. Do not attempt to use ramps that have a slope grade greater than 12%.

For Wall-Mount Installations:

• Casters ship pre-installed with the charging station. Remove the casters and handle before attempting to mount the charging station to a wall (see section 5.1 Removing Casters and Handle for more information).

• Before mounting, first make sure that the wall surface can safely support the combined load of the charging station, equipment stored and all attached hardware and components.

• Always use suitable mounting means when installing to cinder block, concrete, drywall or wood studs.

2. Overview

Your charging station is an all-in-one solution for storing and charging for up to 32 devices. With four pre-installed locking/swivel casters and an attachable, reversible handle accessory, your charging station is ideal for mobile applications. Your charging station can also be conveniently mounted to walls, as well as configured for stationary desktop or floor placement. To prevent theft and device tampering, your charging station enclosure comes equipped with locking steel doors.

3. Feature Identification

CSC32AC(W)

Locking Split Doors

Adjustable Storage Shelves (Holds up to 16 Devices per Shelf)

Blanking Panels (Removable)

Reversible Handle

Swivel/Locking Casters

Power Cord Manager

Power Cord Access Holes (1 Located on Each Side)

Padlock Hasp (User Supplies Lock)

Cable Lock Routing Holes (User Supplies Lock)

Side Panel with Keyhole Wall Mount Slots

(See Section 5 for More Information)

Not Shown: AC Charger Units (In Interior of Unit)

Included Accessory Hardware

12 x Hex Screws

Hex Key

4. Setup

Caution! Read All Instructions and Warnings Before Installation!

Warning: Charging stations can be extremely heavy. Do not attempt to unpack or mount the charging station without assistance. Follow the unpacking instructions document that shipped with this product before proceeding with setup. Use extreme caution when handling the charging station and be sure to follow all handling and installation instructions. Do not attempt to install equipment without first stabilizing the charging station.

4.1 Power Requirements

The charging station can be plugged into an AC outlet with a dedicated circuit. An AC outlet with a 20-amp (NEMA 5-20R) AC circuit is recommended for powering the charging station. The AC outlet used to power the charging station should not be shared. The total wattage of the charging station and all connected components should not exceed 1440 watts.

4.2 Installing the Handle Bracket and Power Cord Manager

To install the handle bracket, use the included hex key tool to attach four (4) hex screws to the charging station cabinet A. To install the cord manager, use the same hex key tool to secure the eight hex screws that attach the cord manager brackets (four per bracket) to the charging station cabinet B.

4.3 Adjusting Storage Shelf Dividers

Your charging station comes with two storage shelves with adjustable dividers that can each accommodate up to 16 personal electronic devices per shelf.

Remove any personal electronic devices stored on the shelf tray. Then remove the blanking panel. To remove the shelf tray from the cabinet, push the shelf tray forward to disengage from the mounting hook, then pull the tray up and out. Once the shelf is removed, remove or rearrange the dividers by pushing in the two tabs securing the divider to the rear end A, then push the divider forward to disengage from the shelf tray B. Repeat as necessary for additional shelf dividers.

4. Setup

4.4 Connecting Devices and Powering the AC Unit

The charging station contains two storage shelves to store and charge your devices. Each storage shelf features 16 strain relief bushings that prevent the devices’ power connectors from slipping through the bushing. To connect a device power connector to the charging station’s AC unit, first remove the blanking panels by inserting your fingers into its left and right holes, and lifting the blanking panel up and pulling out A. Connect the device’s power plug into one of the AC charger unit’s receptacles B, then run the power connector through the storage shelf’s power cord opening to establish a power connection C. Repeat for all devices and reattach the blanking panels.

BA C

With the bottom blanking panel removed, find the AC unit’s input plug and cable located in the charging station’s bottom compartment, then push the input plug through the one of the cable access hole grommets located on the either side of the charging station cabinet D (using the same cable access hole side as the power cord manager is recommended). Plug the power cord into the nearest 3-prong, grounded wall outlet and reattach the blanking panel to the unit.

4.5 Door Locks

The split doors contain a lock that is accessible with the included keys.

5. Wall Installation

To use your charging station in a wall-mounting installation, first remove the casters and handle.

5.1 Removing Casters and Handle

Warning: Do not attempt to remove casters from the tablet charge and sync station with any laptops, tablets or other personal electronic devices inside.

To remove the casters and handle for stationary or wall-mount applications, unscrew the sixteen M6 screws securing the four casters (four per caster) to the enclosure A. If the handle and cord manager are attached to the unit per section 4.2, remove using the included hex key tool to unscrew the handle’s four (4) hex screws and the cord manager’s eight hex screws from the charging station cabinet B.

Note: Save the casters, handle and all hardware for future use.

5.2 Wall-Mounting the Charging Station

For wall mounting, you will need:

• Level

• Appropriate tools for wall mounting

• Appropriate hardware for wall mounting (not included)

Warning: Do not attempt to mount the charging station to the wall with any personal electronic devices inside.

There are 4 keyhole cutouts on the charging station cabinet’s side panel. Each keyhole can accommodate an M5 or 3/16” bolt. Each of the keyhole sets are centered 16” apart horizontally and 28.5” vertically (see the corresponding model diagram for exact keyhole locations).

Using a level, measure to position your mounting areas precisely. Use appropriate fasteners (not included) to secure the charging station to the wall. Once the charging station is safely hanging on the fasteners and secured to the wall, open the unit from the rear door and tighten all mounting hardware.

Note: The charging station must be installed by a qualified technician. Before mounting, use a level and tape measure to position your mounting area precisely. Use appropriate fasteners (not included) to secure the charging station to the wall. Use suitable mounting means when installing to cinder block, concrete, drywall or wood studs. Warning: The supporting surface must be able to safely support the combined load of the

charging station, equipment stored and all attached hardware and components. Go to the Specifications section for more information on your model’s weight and dimensions.

16”

28.5”

6. Specifications

Model CSC32AC/CSC32ACW

Cabinet Dimensions (H x W x D) 35.6 x 23.6 x 21.6“ (905 x 600 x 549 mm) Load Capacity* 250 lb. (113 kg) Stationary or Rolling AC Receptacles 32 x 5-15R, 1 x 5-15R AC Dongle (Reserved for Future Expansion) Power Requirement Input: 120V AC, 50/60 Hz, 12 Amps Operating Temperature 32° to 104° F (0° to 40° C) Operating Humidity 5 to 95% RH, Non-Condensing

*Full wall-mount load capacity requires a mounting surface capable of bearing the full load of the charging station and all connected components. Speciﬁcations may be subject to change without further notice.

7. Storage, Service and Cleaning

Storage

The enclosure should be stored in a controlled indoor environment away from moisture, temperature extremes, flammable liquids and gasses, conductive contaminants, dust and direct sunlight. Store the enclosure in its original shipping container if possible.

Service

The enclosure is covered by the limited warranty described in this manual. For more information, visit www.tripplite.com/support.

Cleaning

Before cleaning, always power off the charging station by unplugging it from its AC source. Dampen a clean, lint-free cloth with water and wipe down the unit, as necessary. Allow the surface area to dry before plugging in the unit.

Note: Avoid using abrasive cloths, solvents or aerosol sprays to clean the charging station; doing so can damage the unit.

8. Warranty and Product Registration

2-Year Limited Warranty

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 2 years from the date of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, at its sole discretion.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction).

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.

Product Registration

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marketing name or model number of the product.

FCC Notice, Class B

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications to this equipment not expressly approved by Tripp Lite could void the user’s authority to operate this equipment.

WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country)

• Send the new equipment back for recycling when this ultimately becomes waste

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

+ 16 hidden pages