Tripp-Lite B160-001-VSI Data Sheet

VGA over IP Extender Transmitter over
Cat5/Cat6, RS-232 Serial and IR Control, 1920 x
1440 (1080p), 328 ft. (100 m), TAA

MODEL NUMBER: B160-001-VSI

Converts VGA video + audio to an IP-based signal that is transmitted point-to-point to a receiver 328 ft.
away via Cat5e/6 cable or through a dedicated Ethernet network switch.

Description

The B160-001-VSI VGA over IP Extender Transmitter works with a Tripp Lite B160-Series receiver (sold
separately) to extend and distribute DisplayPort audio/video, RS-232 serial and IR (infrared) remote
signals from the source to the display located up to 328 feet (100 meters) away, which is more than 200
feet farther than a traditional Cat5e/6 solution. By adding a chain of low-cost unmanaged network
switches, such as Tripp Lite’s NG5, you can continue extending the distance between source and display
up to 328 feet per switch.

The B160-001-VSI displays a single source on a single display or distributes a single signal to multiple
displays. Create a multi-in, multi-out installation with up to 64 transmitters and 255 receivers* by
connecting dedicated managed Ethernet network switches** with Internet Group Management Protocol
(IGMP), such as Tripp Lite’s NSS-G16D2.

Highlights

●

Compatible with Tripp Lite
B160-Series A/V over IP
receivers

●

Video source can be sent to any
analog or digital display

●

Supports video resolutions up to
1920 x 1440, including 1080p*

●

HDMI output on transmitter for
connecting local display

●

Plug and play—no software or
drivers required

Package Includes

●

Transmitter unit

●

External power supply (Input:
100–240V, 50/60 Hz, 0.5A;
Output: 5V 2A)

●

Plug adapters for U.S., U.K.,
Europe and Australia

●

IR-Out cable

●

3.5 mm to DB9 adapter cable
(M/F)

●

Mounting hardware

●

Owner’s manual

With a compatible B160-Series receiver, you can send the VGA video source to any analog or digital
display, including HDMI and DisplayPort™, allowing you to mix and match technologies and use existing
monitors. An IGMP-enabled switch will let you manage all connections for centralized control over which
sources show on which displays.

The B160-001-VSI supports video resolutions up to 1920 x 1440, including 1080p, though it’s limited to
the maximum resolution of the receiver. It mounts to a wall, rack or pole using the included hardware. An
HDMI output port allows connection of a local display.

1 / 4

*Unmanaged switch installations are limited to two transmitter units. Number of receivers is limited to
number of ports remaining on unmanaged switch.
**B160-Series designed for use with dedicated network switch. Connecting to a switch used with other
networking equipment will result in degraded or non-functional performance.

Features

Distributes VGA A/V, Serial and IR Control Signals over Cat5/6 Cabling

●

Converts audio/video to an IP-based signal that is transmitted point-to-point to a display 328 ft. away

●

Add low-cost network switches between transmitter and receiver to continue extending distance up to
328 ft. per switch

●

HDMI output for connecting a local display

Create a Multi-In, Multi-Out Installation Using B160-Series Transmitters and Receivers

●

Connect up to 64 transmitters and 255 receivers through multiple dedicated managed network switches

●

IGMP-enabled switches allow centralized control over which sources show on which displays

●

Video source can be sent to any analog or digital display, so you can mix and match technologies and
use existing monitors

Enhanced Technical Features

●

Supports video resolutions up to 1920 x 1440, including 1080p (limited to receiver’s max resolution)

●

Uses H.264 video compression standard

●

Transmits on 20–60 kHz IR frequency

●

Extends IR control signals that control a source from a remote display

●

Supports RS-232 serial baud rates up to 57600 Bps

●

HDCP and 3D compatible

Plug-and-Play Functionality

●

No software or drivers required

●

Hardware included for mounting on wall, rack or pole

●

Compatible with all Tripp Lite B160-Series A/V over IP receivers

TAA-Compliant

●

Compliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases

Specifications

OVERVIEW

UPC Code 037332196682

PHYSICAL

2 / 4