Tripp SU16KRTHW Product Data Sheet

NETWORK/SERVER UPS

SmartOnline

Hot-Swappable UPS Systems (12 to 20 kVA)

MAXIMIZE AVAILABILITY

You invest in UPS systems to maintain system availability, but

the wrong UPS system will actually cause downtime. Traditional

UPS systems typically require you to power down equipment

for an hour or more during UPS maintenance and repair.

You may even need to disconnect your equipment and hire a

repair technician to rewire power connections before you can

restore operation.

ON-LINE DOUBLE CONVERSION

• Parallel Hot-Swappable Power Modules

• Built-in N+1 Redundancy

• Best-in-Class Energy Efficiency

• High Output Power Factor (0,9)

• Industrial Overload Capacity

• Wide Input Voltage Range

• Pure Sine Wave Output

• Scalable Runtime

Tripp Lite’s SmartOnline Hot-Swappable UPS Systems

maximize uptime, simplify maintenance and reduce service

expenses. You can remove one or both power modules without

powering down your equipment or hiring repair technicians.

The detachable PDU remains connected to your AC source and

your equipment, maintaining system availability without any

interruption to normal operation.

Remove the Power Modules… …And Your Equipment Stays On

SmartOnline Hot-Swappable UPS Systems allow you to remove both power modules without powering down your equipment.

SmartOnline Hot-Swappable UPS Systems Eliminate Downtime!

Traditional UPS System (5+ kVA)

Schedule Downtime (Typically After Hours) Hours to Days

Wait for UPS Repair Technician 4 to 24 hours

Shut Down and Disconnect Equipment 10+ minutes

Disconnect and Remove Old UPS 15 minutes

Install New UPS in Rack and Power Up 20 minutes

Plug In, Start Up and Test Equipment 15+ minutes

SmartOnline Hot-Swappable UPS System (5+ kVA)

Schedule Downtime Not Required

Wait for UPS Repair Technician Not Required

Turn Bypass Switch and Detach PDU 1 minute

Remove Old Power Module 1,5 minutes

Install New Power Module 1,5 minutes

Reattach PDU and Turn Bypass Switch 1 minute

Estimated Time to Repair 5 to 25+ hours

Estimated System Downtime 60+ minutes

Estimated Time to Repair 5 minutes

Estimated System Downtime Zero

NETWORK/SERVER UPS

PROVIDE BUILT-IN REDUNDANCY

SmartOnline Hot-Swappable UPS Systems automatically

provide N+1 redundancy when the equipment load is ≤

the UPS capacity. If one of the parallel power modules requires

maintenance, repair or replacement, equipment still receives

perfect power and battery backup from the redundant power

module. If the equipment load is > 50% of the UPS capacity,

the parallel power modules work together to support the

heavier load.

50% of

SAVE ENERGY AND REDUCE COSTS

SmartOnline Hot-Swappable UPS Systems provide exceptional

energy efﬁciency. For each 80 kVA of on-line UPS capacity,

SmartOnline Hot-Swappable UPS Systems can save more than

100 megawatt-hours of electricity and USD $10 000 per year

while reducing CO2 emissions by nearly 70 metric tons.*

* The estimate compares a SmartOnline Hot-Swappable UPS System operating at 96% efﬁciency in Economy Mode to a traditional on-line UPS system operating at 86% efﬁciency. The calculations assume a 24x7 duty cycle and estimated electricity cost of USD $0,10 per kilowatt-hour. Savings vary with application and actual electricity cost.

SUPPORT HEAVIER LOADS

A high output power factor (0,9) allows you to connect more

equipment to the UPS and better utilize your facility’s existing

circuits and space. Industrial-grade overload capacity supports

higher inrush currents at equipment startup and ﬂuctuating

power demands during operation without interrupting

production lines. SmartOnline Hot-Swappable UPS Systems

handle overloads up to 150% for brief periods and transfer

to bypass dynamically to sustain productivity during higher

overloads for extended periods.

SUPPLY PERFECT POWER

On-line operation with continuous double conversion

corrects input voltages as low as 100 V and as high as 300 V.*

SmartOnline Hot-Swappable UPS Systems deliver pure sine

wave output, regulate output voltage within 2% of nominal,

regulate frequency within 0,1% of nominal and comply

with international standards for voltage- and frequency-

independent operation.**

* Input voltage range is 156 to 280 V at 100% load, plus 281 to 300 V at 90% load and 100 to 155 V with linear derating to 50% load at 100 V. ** Voltage- and frequency-independent (VFI-SS-111) operation complies with EN 62040-3:2001.

CENTRALIZE POWER MANAGEMENT

SmartOnline Hot-Swappable

UPS Systems connect to the

network through the optional

SNMPWEBCARD accessory

or through a networked

computer connected to the

built-in USB or serial port.

The included PowerAlert

Network Management System (NMS) allows you to manage

hundreds of networked UPS systems and PDUs over the

network.

PowerAlert Software

INCREASE RUNTIME

The included hot-swappable batteries provide sufﬁcient

backup runtime to support uninterrupted operation during

typical outages. For applications or adverse power conditions

that require additional runtime, you can connect as many

external battery packs as you need.

Estimated Battery Backup Runtime

Connected Equipment Load

Model

12 kVA UPS (Included Batteries)

12 kVA UPS and (2) BP192V12-3U

16 kVA UPS (Included Batteries)

16 kVA UPS and (2) BP240V10RT3U

20 kVA UPS (Included Batteries)

20 kVA UPS and (2) BP240V10RT3U

Runtime varies with load, temperature, battery condition and other factors. Visit www.tripplite.com for additional runtime options.

2 kW 4 kW 6 kW 8 kW 10 kW 12 kW 14 kW 16 kW 18 kW

29 min 12 min 7 min 4,5 min 2,8 min — — — —

133 min 59 min 36 min 25 min 18 min — — — —

80 min 35 min 20 min 13 min 11 min 8,4 min 6,7 min — —

184 min 84 min 52 min 36 min 27 min 21 min 17 min — —

80 min 35 min 20 min 13 min 11 min 8,4 min 6,7 min 4,9 min 4,3 min

184 min 84 min 52 min 36 min 27 min 21 min 17 min 17 min 14 min

+ 2 hidden pages