Triplex MP4 SDVR User Manual

Triplex MP4 SDVR

DVR SYSTEM

MANUAL

Stand Alone Type

050131041130

Firmware 2.0 Version
Revision Date : 2005. 01. 31.

• MODIFICATION CONTENTS

Firmware ver 2.0

Modification Date: 2005.01.31

Please refer the below message to confirm the modify contents.

1. PTZ CONTROL

* ADD PRESET FUNCTION : FOR PELCO-D PROTOCOL

* ADD SWING FUNCTION : FOR DONGYANG CAMERA (D-MAX)

2. CD-RW ( CD Read&Write Burner )

* ADD CD-RW FUNCTION FOR DATA BACK-UP

3. IE BROWSER

•ADD IE BROWSER ( ALLOW FOUR USERS MONITORING AT THE

SAME TIME )

•INDEX

■ CHAPTER 1 . ( Specification & System Organization )

1.1 Specification ------------------------------------------------------ 7

1.2 Product Contents List ------------------------------------------------ 8

1.3 System Organization ------------------------------------------------ 9

■ CHAPTER 2 . ( Description )

2.1 Front Panel ------------------------------------------------------- 10

2.2 Rear Panel ---------------------------------------------------- 11

2.3 Remote Controller ----------------------------------------- 12

■ CHAPTER 3 . ( Installation )

3.1 Hard Disk Installation ------------------------------------------------ 13

3.2 Camera Connection ------------------------------------------------ 15

3.3 Monitor Connection ------------------------------------------------- 15

3.4 Computer Connection --------------------------------------------- 15

3.5 Network Connection ------------------------------------------------ 15

3.6 Alarm/Relay/PTZ Connection ------------------------------------------- 16

3.7 Power Connection -------------------------------------------------- 16

3.8 Finishing Installation ------------------------------------------------- 16

※ Hard Disk Format ------------------------------------------------- 17

■ CHAPTER 4 . ( Monitoring )

4.1 System Power ON --------------------------------------------------- 18

4.2 Select Screen Mode ------------------------------------------------- 18

4.3 Convert Screen Mode ------------------------------------------------ 19

4.4 Control PTZ/Focus -------------------------------------------------- 19

4.5 System Power OFF -------------------------------------------------- 20

■ CHAPTER 5 . ( Search )

◎ Go to Search ----------------------------------------------- 21

5.1 Search by Date/Time ------------------------------------------------ 21

5.2 Search by Event -------------------------------------------------- 22

•INDEX

■ CHAPTER 6 . ( Menu )

◎ Go to Menu ----------------------------------------------------- 24

◎ Menu Initial ------------------------------------------------------- 24

6.1 Display ---------------------------------------------------------- 25

6.2 Record ---------------------------------------------------------- 25

6.2.1 Size/Rec. Rate/Quality ---------------------------------------- 25

6.2.2 Timer Recording Setup -------------------------------------26

6.2.3 Motion Detection Setup -------------------------------------- 27

6.2.4 Alarm Recording Setup ----------------------------------------- 27

◎ Time Recording Weekly Setup -------------------------------------- 28

◎ Partial Motion Region Setup ----------------------------------------- 29

6.3 Camera ---------------------------------------------------------- 30

6.3.1 Status/Title Setup ----------------------------------------------- 30

6.3.2 Covert/PTZ Setup --------------------------------------------- 30

6.3.3 Color Setup -------------------------------------------------- 31

6.4 AUDIO -------------------------------------------------------- 31

6.4.1 Audio Recording Setup ------------------------------------------- 31

6.4.2 Live Audio Setup ------------------------------------------------ 32

6.5 ALARM --------------------------------------------------------- 32

6.5.1 Alarm Input Setup ----------------------------------------------- 32

6.5.2 Relay Output Setup ---------------------------------------------- 33

6.6 SYSTEM -------------------------------------------------------- 33

6.6.1 Date/Time --------------------------------------------------- 33

6.6.2 Network ------------------------------------------------------- 34

6.6.3 Buzzer Setup --------------------------------------------------- 34

6.6.4 Password ---------------------------------------------------- 34

6.6.4.1 Administrator Password --------------------------------------- 34

6.6.4.2 Manager Password ------------------------------------------ 35

6.6.4.3 Operator Password ---------------------------------------- 35

6.6.4.4 Network Password --------------------------------------- 35

6.6.5 Disk Write Mode ----------------------------------------------- 36

6.6.6 System Information --------------------------------------------- 36

6.6.7 Factory Default ------------------------------------------------ 36

•INDEX

6.7 CD-RW Back-up ----------------------------------------------------- 37

■ CHAPTER 7 . ( Remote Agent )

◎ System Requirement --------------------------------------------38

◎ DVR Remote Agent 1.0 Installation ------------------------------- 39

7.1 Monitoring

7.1.1 Function Introduction ------------------------------------------ 41

7.1.2 Screen Division Selection ----------------------------------------- 42

7.1.3 PTZ Control --------------------------------------------------- 42

7.1.4 Selection Network ID -------------------------------------------- 42

7.1.5 AVI File Conversion -------------------------------------------- 43

7.1.6 Color Adjustment ------------------------------------------- 43

7.2. Search

7.2.1 Function Introduction ------------------------------------------- 44

7.2.2 Search Method ------------------------------------------------- 45

7.2.3 Search Option --------------------------------------------- 46

7.3. Setting

7.3.1 Connection ID Setup ----------------------------------- 51

7.3.2 Option Setting ----------------------------------------------- 52

■ CHAPTER 8

Time Table ------------------------------------------------------ 53

PTZ Protocol --------------------------------------------------- 54

PTZ Control ----------------------------------------------- 55

8.1 PTZ Reset --------------------------------------------------56

8.2 Swing ------------------------------------------------ 56

Cross cable making tip ------------------------------------------- 57

• SUPPLEMENT LIST

1. PTZ Control

1.1 PTZ Control -------------------------------------------------- 77

1.2 FOCUS/IRIS Control ------------------------------------------- 77

1.3 PRESET Control ----------------------------------------------- 78

11.4 SWING Control ----------------------------------------------- 78

2. Cross Cable Making Tip ----------------------------------------- 79

• Specification & Organization

1.1 Specification

7

• Specification & Organization

1.2 Product Contents List

Please confirm the contents when you open packing.

① Basic Contents

User’s Manual

② Option Contents

DVR Machine

Remote Controller

12V Adaptor Power Cable

Remote Client Program
Install CD

AAA Battery X 2

80GB HDD

VGA OUT Install Kit

8

• Specification & Organization

1.3 System Organization

Alarm Sensor #1-4 Relay Out

Remote Client PC

Camera #1-4

Video In

Alarm Input/Out

AVR 400s

VCR

Video Out

VGA
Monitor

NETWORK

TCP/IP

Image Printer

Remote
Controller

AV Monitor

9

• Description

2.1 Front Panel

3

112

4

6

9

10

12

1. Power : System Power On/Off.

2. LED Indicator : Indicate Present System Situation
( POWER: System On/Off , RECORD: Record On/Off , 1

NETWORK: Client Network Connect On/Off , ALARM: Alarm Sensor On/Off )

3. Channel Select Button : When Select Channel or Input Password

4. SCR Mode : When Select Screen Division Mode or Rotation Mode

5. Menu : Go to System Menu

6. Search : Go to Search Mode for Searching Recorded Video

7. PTZ/Focus : Go to Camera PTZ/Focus Control

8. Remote Controller Sensor Input

75

8

11

9. Search Controller : Searching Recorded Video or Control Menu & PTZ/Focus

10. Enter : Press Enter to Apply Changing Setup

11. Return : Cancel Setup or Return Previous Mode

12. CD-RW Burner

Tip

• Power Button is soft style to Prevent System Failure by wrong operation.

• Channel Selection Button is prior to SCR mode.

• When Remote Controller Sensor Input is blocked by something, it cause 1
remote controller do not work properly.

• When press any button, it operate with Beep Sound.

10

• Description

2.2 Rear Panel

①

②

① Video In : BNC Port which Connected DVR & Camera (4 Camera Connectable)

② Loop Back : Output DVR Camera Video to Loop Back Port (4 BNC Port)

③ Monitor Out : Output DVR Video when connected AV Monitor

④ Spot Out : Output Spot-out Video to AV Monitor

⑤ NTSC/PAL : Select NTSC or PAL Type

⑥ VGA Out : Connected VGA Card to Output Video at Computer Monitor (Optional)

⑦ SVHS : Output Video to Connect SVHS Terminal

⑧ Audio Out : Output Recorded Audio

③

⑥⑨

④⑤

⑦

⑧⑩⑪⑬

⑫

⑨ Audio In : AV Terminal which Connected Camera #1~4 for Input Audio
⑩ Ethernet (TCP/IP) : Connect Port for LAN Cable (Possible to Remote Survey to Connect

to Client)

⑪ Alarm/Relay/RS-485 : Connect Port for Sensor & Relay, PTZ

⑫ RS-232C : For Program Debug & Expand Connection (NOT AVAILABLE NOW)

⑬ DC Power Input Terminal : Power Supply by DC 12V Adaptor

Tip

• When System Installation, Please Connect when System Off.

• Please Use Specific Adaptor when Power Supply.

19

• Description

2.3 Remote Controller

POWER

System
ON/OFF

RETURN

Cancel
Setup or
Return to
Previous

MENU: Open menu

Channel Select Button
(4ch Available, #1~4 Button)

ENTER: Apply Setup Change

Search Controller : Control Playback Option

(EX. Speed of Playback, Move on Menu,

1Control PTZ/Focus)

• Unused Button’s Description is Omitted.

• Every Button is Operated Same as Front Panel Button.

• Remote Controller can Operate when Remote Controller Sensor Input Part Reacted.

※ If there are many DVRs at the same place, they are reacted together when press remote controller

Change Screen
Mode

20

Open
Search Mode

PTZ/IRIS
Mode

• Installation

3.1 Hard Disk Installation

① Jumper Setup Master or Slave

※ Example of Samsung HDD Jumper Setup

• Jumper Setup as Master or Slave refer to Explanation of 1
Surface Hard Disk

• Jumper is located at Hard Disk Data Cable or Rear 1 Side
of Hard Disk

• If One Hard Disk Installation, Setup as Master

1 If Two Hard Disk Installation, Second One Setup as Slave

‼ When Hard Disk Add or Exchange, Must System Off

Properly (Power Button System Off). If not, it’s a cause of

Fatal Error of Disk.

• Refer to General Pin Setting in Jumper Pin Setting on HDD Surface

• When One HDD Install, Setup Pin as Master

1 and Connect Pin at the Left end of Jumper

• When Two HDD Install or Add HDD, One is for Master and 11the
Other is for Slave. Slave Setup has No Pin.

• When More than Two HDD Installation, Setup as Master & Slave

1 to Connect One IDE Cable the Same Method of Above

‼

② IDE Cable Connection to Main Board

!!Please use HDD which can supply higher than UDMA66.!!

• Confirm the IDE Cable Inside of Product

• Among the Three Connector, Indicated Blue Color 1
Connector Must be Connected with Main Board. Other 1
Connectors Connected with HDD

13

• Installation

② Connect IDE Cable to Hard Disk

• Insert Disk, Red Cable Head to Power Cable Plug

• Connect Power Cable to Hard Disk in the Same Way

※ If One HDD Install, Connect with End of Connector (Black)

Recommended.

If Add HDD, Connect with Middle Connector (Gray)
Recommended.

One HDD Installation Two HDD Installation

③ After Finishing Cable Connection, Attach Hard Disk with Screw & Bracket

Tip

• IDE Hard Disk can connect two equipment at one
cable (port). For the purpose of prevent confusing, two

equipment named ‘Master’ & ‘Slave’. ’Master’ is one
hard disk or first hard disk and ‘Slave’ is below second

hard disk.

ㅡMaster, Slave?

14

• Installation

3.2 Camera Connection

Connect Camera at BNC Port in Back Side Panel.

3.3 Monitor Connection

Connect Monitor Terminal or S-VHS Terminal to Monitor

3.4 Computer Connection

Connect VGA OUT Terminal to Computer Monitor

3.5 Network Connection

Connect Ethernet Terminal and Network Cable

15

• Installation

3.6 Alarm/Relay/PTZ Connection

①②

①ALARM

Alarm Input - ‘IN1, IN2, IN3, IN4’ : Connect Sensor Input by Channel

‘GND’ : Connect Ground System

② RELAY

Alarm Output – ‘NO, NC’ : After Checking Alarm Output Type (Normal Open or Normal Close)

and Connect to ‘NO, NC’
‘COM’ : Connect Remain Grounding Conductor

③ RS-485

Connect PTZ Camera – ‘D+, D-’ : Connect PTZ Camera Control Line (+ , – Terminal)

RS485

D+

D-

PTZ 14 Pin Cable

⑨ R+

⑩ R-

③

⑪ T+

⑫ T-

3.7 Power Connection

Connect DC Power Input Terminal and Specific Adaptor

3.8 Finishing Installation

System Start by Power Button after Finishing Installation

16

• Installation

※ Hard Disk Format

- If Do Not New Hard Disk Format, System Can’t Recognize the HDD.
So there’s Same Situation of No HDD. Please Format HDD when Insert New HDD.

(Only Display Possible, Not Work Menu & Search)

Checking Hard Disk Drives ...
Di sk0 [SANSU NG SP 0 0 0 2N]
Total 1 H ard Di sk Drive Found.
New Syst em Disk Detected.
All Disks will be formatted.
Format All Disks ? NO (0 )

1. Power On

3. System Start

(Initial Mode)

17

2. New HDD Format

(Select Play , Backward Play Key)

SETUP

Use r
Pa sswo rd

Ad m i n istra to r

•Sys pwron

4.1 System Power ON

Picture for Power On
after Finishing Installation

• Press Power Button to Start System

• After Checking Hard Disk, Need input Password to

1 Operation

• Initial Screen View Mode is Quad Division Mode

1 and Recording Mode

CAMERA

2004/01/01

00:00:00

• Each Channel Indicate Camera Name & Recording Status

• Present Time & Date Indicate at Monitor Central Lower Side

Tip

• Check System Condition at LED

POWER : Showing System On/Off
RECORD : Showing Record On/Off
NETWORK : Showing Client Connection Status
ALARM : Lighting when Sensor Alarm Activate

4.2 Select Screen Mode

• Select One Channel among 4 Channels

• Move to One Enlargement Watch Mode when Quad Screen Division Mode

• Move to One Enlargement Watch Mode when Rotation Mode

18

•Monitoring

4.3 Convert Screen Mode (SCR MODE)

• User can Select 3 Kinds Watch Mode

SCR MODE

① Quad (4CH) Division Watch Mode

② Selected 1CH Watch Mode

③ 4CH Rotation Watch Mode

• Quad (4CH) Watch Mode is Initial Mode when System Start

Quad (4CH) Division
Watch Mode

4.4 PTZ/FOCUS Control

• Control Camera PTZ (Pan/Tilt/Zoom) & Focus (Only Useable for Proper Camera)

PTZ/FOCUS

• Press PTZ/FOCUS Button to Open PTZ Menu at Right-Under Side and Control by

1 Search Controller

• Press PTZ/FOCUS Button Second Time to Open FOCUS/IRIS Menu and Control by 1
Search Controller

Selected 1CH
Watch Mode

PTZ CTL

UP

LEFT RIGHT

DOWN

FOCUS/IRISCTL

UP

LEFT RIGHT

DOWN

4CH Rotation Mode

Control Camera PTZ &
Focus by Search Controller
on PTZ Menu

Search Controller

19

• Monitoring

4.5 System Power OFF

S HUTDOWN

Use r
Pa sswo rd

Tip

Ad ministra tor

• Press Power Button to System Off

• Input Password and Press Enter to Shutdown System

• System Log-On Possible ID : ‘Administrator’, ‘Manager’, ‘Operator’, ‘Network’

Administrator: All Function Access (System On, Shutdown, Setup, Search)
Manager: System On and Search
Operator: System On
Network: Connect by Remote Program

20

• Search

⊙ Go to Search Mode

Se a rc h

1. Se arch by Dat e/Time

1. Se arch by Dat e/Time

>

>

Search Recorded Data

5.1 Search by Date/Time

- Possible to Search Recorded Date & Time

20 04

56

4

12 13

11

19 20

18

25

567

12

19

27

26

14

13

20

21

1
8

15

Mar

Su n M on Tu e We d Th u Fr i Sa t

123

78 9

14 15 16 17

21 22 23

28 29 30 31

23

10

10

9

16

17

10

24

4

11

18

SEARCH

• Press Search Button and Log-In
Administrator or Manager

• Use Direction Key to Move Menu

ENTER

RETURN

• Return to Previous.
(Move to Previous Menu or Exit Search

• To Open Each Menu Press Enter

1 Mode and Return to Watch Mode)

① Move Cursor to Selected Date in Calendar

(Recorded Date & Time Indicated by Gray Color)

② Press Enter to Open Selected Date

③ Recorded Time Appear to Under Side

④ Press Enter at Selected Time

(One Scale is 15 Minutes)

⑤ Menu Disappear and Output Recorded Video

• Showing Recorded Date & Time at Left-Upper Side 1 as
Watch Mode. 1 Showing Playing
Condition at Right-Under Side.

• Channel Selection Button in Watch Mode & SCR Mode 1 Button
are Apply the Same as Search Mode.

(But Menu, Search, and PTZ/Focus Buttons are Exception)

21

2004/01/01
00:00:00

>

• Search (Event)

• Control Playing Video

① : Basic Playing Mode (Normal Speed (1X) Forward Playing)

② : Normal Speed Backward Playing

③ : Pause Video

④ : Fast Forward (2 ~ 64 Speed)

⑤ : Fast Backward (2 ~ 64 Speed)

⑥ : Same Function as # ④,⑤

※ Press Normal Forward/Backward Button in Pause, Move to Next/Previous Frame.

5.2 Search by Event

- Searching Video with Event Occurrence to Set up Period

Tip

• Alarm, Motion, System can be Select plural by Check (V)-(ENTER)

• To Change Setup, Press Enter and Press Direction Key
After Changing Setup, Press Enter to Exit.

Set up Period to Select Start Date & Finish Date for
Searching Event

Alarm : Searching Alarm Event during the Selected

1 Period

Motion : Searching Motion Detected Event during 1
the Selected period .

Timer : Searching Schedule Change or Recording

1 Setup Change Event

System : Searching Power On/Off Event (etc.) 1
Concerned System Event

Event List Showing at Below Output Window

22

• Search

• Date : Indicate Event Occurrence Order & Date

Time : Indicate Event Occurrence Time

Event : Indicate Event Contents & Camera No.

• Event Searching Method

① User can Search Event Using by Direction key

② Search Event to Press Enter at Selected Event

from Event Occurrence Time

③ Control Video is the same way as Time Mode Control

Tip

• The Search by Event is not Base on Video, but Event Occurrence Time.

31

• Menu

⊙ Go to Menu

Use r
Pa sswo rd

SETUP

Ad ministra tor

① Press Menu Button on Front Panel in Watch Mode

② Ask Password

③ Input Password Using by Channel Select Button

1 [1][2][3][4])

④ After Input Password Press Enter to See Menu

Tip

⊙ Menu Initial

1. Disp la y

2. Record

3. Camera

4. Audi o

5. Alarm

6. System

• Initial Administrator, User, Network Password is 1234.

• Showing Password as *

• Changing Password (MENU->6.System->4.Password )

• Only Watch Mode can go to Menu.
(Search & PTZ/Focus Mode can’t move to Menu)

• Every System Setup can Change or Maintain

1 at Menu (6 Setup)

MENU

•

>

>

>

>

>
>

•

ENTER

To Open Detail Menu or to Apply Input

Move to Menu Using by Up &
Down Button

•

RETURN

Return to Previous Menu or Return to Watch Mode

24

• Menu

6.1 Display

- Video Setup for Watch Mode

1. Date/Time : Date & Time Mark On/Off

2. Title : Camera Name On/Off

3. Status : Record Condition Mark On/Off
(Recording: Red, Pre-recording : Green)

4. Border : Border Mark On/Off when
4CH Division Watch Mode

5. Border Color : Select Border Color
(White, Blue, Red, Yellow, Green, Gray)

6. Sequence Dwell : Setup Rotation Cycle Time (1~60
Sec.) when 4CH Rotation Mode at Watch Mode

7. Spot-Out Dwell : Setup Spot-Out Time Cycle (1~60
Sec.) to Transmit Video

8. Deinterlace Mode : Remove Screen Spread on High
Resolution , Low Frame
※Only Applying When D1(704X480)

6.2 Record

- Setup Image Record

6.2.1 Size/Rec.Rate/Quality – Setup Recording Resolution, Compression Rate, Quality

-Camera : Indicate Camera No. to Setup

-Size : Setup Resolution

-Rec.Rate : Setup Compression Rate

-Quality : Setup Quality of Recording Video

25

• Menu

• Size : 352*240, 704*240, 704*480

Rec.Rate : Possible to Select (1~30)

Quality : Possible to Select 3 levels (High, Low, Standard)

• Indicate Frame No. to Control Size & Rec. Rate

Overlimit Recording Capacity

Tip

• When Setup, Please Refer to Below NTSC & PAL Type

NTSC : 352*240(120fps), 704*240(60fps), 704*480(30fps)
PAL : 352*288(100fps), 704*288(50fps), 704*576(30fps)

• Possible to Setup Size & Rec. Rate, Quality per Each Channel

• When Applying Change Setup, Press Enter, 1
When Cancel Change Setup, Press Return.

• If Frame Over, Showing a Message ‘Overlimit Recording 1
Capacity’ and Impossible to Change Size & Rec. Rate

6.2.2 Timer Recording Setup – Record On/Off or Time, Motion Setup

• Camera : Indicate Camera No. to Setup

• Record : Record On/Off

• Start : Setup Recording Start Time (0~24 hr)

• Stop : Setup Recording Finish Time (0~24 hr)

* Recording Time is between Start Time and Finish Time.

• Motion : Motion Detection Recording On/Off
(Record Setup must be ‘On’, when Motion Detection 1

Recording.)

26

• Menu

6.2.3 Motion Detection Setup – Motion Detection Area & Sensitivity

• Camera : Indicate Camera No. to Setup

• Sensitivity : Control Sensitivity (1~100)

• Region : Setup Motion Detect Range

• When Choose Region as Partially, Move to Partial 1

Range Setup. Press Enter After Partial Range Setup

1 to Finish Region Setup.

• Pre-Motion Duration : Setup Pre-Motion Duration Time.

1 (1~5 sec)

• Post-Motion Duration : Setup Motion Detect Recording 1

Time after Motion Detected (5sec~3min)

Large No. is More Sensitive.

Entirely – Setup Entire Screen

Partially – Setup Partial Screen

6.2.4 Alarm Recording Setup – Recording Setup for Alarm Activated

• Camera : Indicate Camera No. to Setup

• Record : Setup Record On/Off when Alarm Activated

• Start : Setup Alarm Recording Start Time (0~24 hr)

• Stop : Setup Alarm Recording Finish Time (0~24 hr)

• Pre-Alarm Duration : When Alarm Recording, Setup

1 Start Recording Time before Alarm Activate (1~5sec)

• Post-Alarm Duration : Setup Alarm Recording Time

1 after Alarm Activate (5sec~3min)

Tip

• Motion Setup Work by Time Schedule and Alarm Schedule Work Independently.

27

• Time recording

⊙ Time Recording Weekly Setup

①②

Weekly mode Setup at Record Setup

Scheduled Region Indicated Yellow

③④

After ‘Deselect’ Schedule, Activated Region by
Press ‘ENTER’ and Select Date & Time to Move

Cursor

After Selecting Region and Press ‘ENTER’ Again to

Finish Schedule Setup (Red)

⑤⑥

Setup Date & Time Schedule in the Same Way.
After Finishing Schedule Setup,

Press ‘Return’ for Save & Exit

• Select All : Entire Region Select

• Deselect All : Cancel Region

• Save & Exit : Save Changing Setup & Exit

• Cancel : Cancel Changing Setup & Exit

28

• Menu

⊙ Partial Motion Region Setup

:Non-Activate Move Cursor :Activate Partial Setup Cursor :Partial Setup Finish Cursor :Non-Activated Region

①②③

Region Initial View

④

When Select Multi Region,
Using Direction Key in ② to
Expand Non-Activate Region

⑦

Move Cursor by Direction Key and
Press Enter at Selected Region

⑤ ⑥

Press Enter to Select Multi Non­Activate Region

⑧

• Select All : Select Entire Region

• Deselect All : Cancel Region Setup

• Save&Exit : Save the Change Setup & Exit

• Cancel : Cancel Change Setup & Exit

Press Enter again to see Region
as a Blue Color and Setup Non­Activate Region

Same Method as ④⑤, Possible to
Expand Non-Activated Region

For Reducing Partial Region,
Cancel Non-Activate Region in
Same Way as ④⑤

When Finishing Partial Region
Setup, Press Enter to Save &
Exit

29

• Menu

6.3 Camera

- Setup Camera

6.3.1 Status/Title Setup – Camera Connection Status & Camera Name Setup

• Camera : Indicate Camera No. to Setup

• Status : Indicate Camera Status
(Connected/Disconnected)

• Title : Setup Camera Name to Show Left-Upper Side

Tip

• Title Input Method

Using Direction Key, Up & Down Keys for Alphabet A~Z, Numerical No. 0~9

1 Left-Right Keys for Move to another Letter.

6.3.2 Covert/PTZ Setup

• Camera : Indicate Camera No. to Setup

• Covert : Setup Covert On/Off
*What’s Covert?

When Covert On Watch Mode, Display Video is 11

Hidden, but Recording is On.

• PTZ Address : Select PTZ Camera Address

• PTZ Protocol : Select Kind of PTZ Camera

• Baud Rate : Setup PTZ Communication Speed

(2400, 4800, 9600 BPS)

※PTZ Supplied Protocol :

Samsung(MRX-1000), HoneyWell(GC/GMC-755 Zoom)
Kalatel(KTD-312), Panasonic(WV-CS850),
Panasonic(WV-CSR604), PELCO-D, PELCO-P,
Sensormatic-ADPT8, Vicon(surveyor99), Sunin DSC-230
D-MAX ,HoneyWell(GC-655N)

30

• Menu

6.3.3 Color Setup – Control Video Color

6.4 Audio

- Setup Audio

6.4.1 Audio Recording Setup – Audio In Setup

• Camera : Indicate Camera No. to Setup

• Bright : Control Monitor Bright

• Contrast : Control Monitor Contrast

• Color : Control Monitor Color

• Tint : Control Monitor Tint

* All Setup Possible to Control 0~100

• Camera : Indicate Camera No. for Setup

• Audio Rec. : Setup Recording On/Off from External 1
Audio In Terminal

• Audio Ch. : Setup Audio In Terminal Channel &

1 Audio Output Camera

Tip

• User can Listen Saved Audio with Saved Video

• Audio Check in Search is Possible Only Normal Speed (1X) Forward 1
Playing at 1CH Mode (Audio Recorded Channel)

31

• Menu

6.4.2 Live Audio Setup – Audio Out Setup

6.5 Alarm

- Setup Alarm & Relay

6.5.1 Alarm Input Setup – Alarm Sensor Setup

• Live Audio : Audio Output ON/OFF
Live Audio Output from Audio In Terminal

• Monitoring Ch. : Select Channel for Audio Output

1 Nr. 1~4 Audio In

• Alarm : Indicate Alarm Input Terminal No.

• Status : Setup Alarm Sensor Connection Status
(Connected/Disconnected)

• Camera : Input Camera No.1~4 to Connect Alarm

• Type : Setup Alarm Sensor N/Open, N/Close Type

Tip

• Generally Alarm Sensor can be Divided Two Types.

Normal Open Type is Open Sensor Electrically and Reacted when 1

Signal is Connected.

Normal Close Type is Close Sensor Electrically and Reacted when 1

Signal is Disconnected.

32

• Menu

6.5.2 Relay Output Setup – Alarm Relay Setup

• Alarm : Indicate Alarm Input Terminal No.

• Relay Out : Setup Relay Connect with Alarm Sensor

• Mode : Setup Reacted Relay as Latched/Transparent Mode

• Duration : Setup Reacted Relay Time 1
(5sec~5min or Until key-in)

• Relay Type : Setup Relay Type N/Open or N/Close

Tip

• Latched/Transparent

Latched – When Sensor Alarm Activated, Relay Reacted in Setup Duration
Transparent – Relay Reacted Temporary During Sensor Alarm Activate

6.6 System

- Basic Environment Setup

6.6.1 Date/Time – Date & Time Setup

• Date : Setup Present Date (YYYY-MM-DD).
(If Time Setup to Past Date, Ask Delete Data for the Past Date.

NO->Date/Time No Change, YES->After Delete Past Data and Change Date/Time )

• Date Format : Select Date Output Type (Ex: 2004-00-00, 2004/00/00)

• Time : Setup Present Time

• Time Format : Setup Time Type as 12 Hour Base or 24 Hour Base

• Daylight Saving : Summer Time Applying Status

33

• Menu

6.6.2 Network – Setup TCP/IP

6.6.3 Buzzer Setup – Setup Key Sound to Speaker

• IP Address : Input IP Address

• Gateway : Input Gateway IP for Internet Server

• Subnet Mask : Input Subnet Mask IP

• Network Speed : Setup Network Speed
(Network Speed from System, Depend on Network Status)

※ If Change Network Setup, New Change Apply

when after Rebooting.

• Alarm Input : Alarm On/Off when Alarm Activate

• Videoloss : Alarm On/Off when Camera Disconnected

• Disk Full : Alarm On/Off when Hard Disk Full

• Disk Error : Alarm On when Hard Disk Error

• Key Input : Setup Key Input Sound

6.6.4 Password – Setup Password

6.6.4.1 Administrator Password – Setup Menu & System On/Off

• Current Password : Input Current Password (Initial Password : 1234)

• New Password : Input New Password

• Re-enter the Password : Re-Confirm New Password

• Save&Exit : Applying New Password

34

• Menu

6.6.4.2 Manager Password – Possible System On & Search, But Can’t Change Setup

6.6.4.3 Operator Password – Possible System On, But Can’t Change Setup and Search

• Current Password : Input Current Password
(Initial Password : 1234)

• New Password : Input New Password

• Re-enter the Password : Re-Confirm New Password

• Save&Exit : Applying New Password

• Current Password : Input Current Password
(Initial Password : 1234)

• New Password : Input New Password

• Re-enter the Password : Re-Confirm New Password

• Save&Exit : Applying New Password

6.6.4.4 Network Password – Setup Remote Connection Program Password

• Current Password : Input Current Password
(Initial Password : 1234)

• New Password : Input New Password

• Re-enter the Password : Re-Confirm New Password

• Save&Exit : Applying New Password

35

• Menu

6.6.5 Disk Write Mode – Setup Hard Disk

• Disk Overwrite : Select Overwrite Permission when

1 Hard Disk Full

O N: Overwrite Hard Disk from Oldest Data
OFF: When Hard Disk Full, Stop Recording and 1

Buzzer Activate (Refer to Menu 6.3 Buzzer Setup)

• Disk Initialize Now : Refreshment Hard Disk
All Recorded Data Deleted

• When Select Disk Initialize, Alarm Message Showing.

1 Select ‘Yes’ to Start Disk Initialize.

※When Change Disk Overwrite ON/OFF Mode, the Change will be Applied from Changing Time.

For Example When Overwrite On Mode & HDD Full, Change to Overwrite Off Mode and then it will be Applied New Data
Fill HDD Full after Changing Time.

6.6.6 System Information – Product information (

6.6.7 Factory Default – Every Setup Initializing

Version etc)

• S/W Version : Indicate Software Version of the Product

• H/W Version : Indicate Hardware Version of the Product

• Video Signal Type : Indicate Video Signal Type

• Disk Size : Indicate Hard Disk Capacity

• Number of HDD : Indicate Present Installed HDD No.

• IP Address

• MAC Address

• Press Enter to Start Initialize

• Showing Warning Message and Press OK to Run Initialize

• If do Factory Default, Every Setup is Initialized, but

1 Saving Image is Not Erase.

36

• Menu ( CD-RW Back-up )

6.7 CD-RW Back-Up

⊙ Go to Menu

Use r
Pa ssword

1. Display

2. Record

3. Camera

4. Audio

5. Alarm

6. Syst em

7. Back Up

7. Back Up

Device

Start Tim e
End Time

All Ch1

Vide o

Audi o

Ti tle

SETUP

Adminis tra tor

SETUP

>
>
>
>
>
>

>

ASUS CRW-S282 AX

2005.01.31 15:21

2005.01.31 15:24

>

Ch2 Ch3

>
>

>

Back Up CD Event

>

① Press Menu Button on Front Panel in Watch Mode

② Ask Password

③ Input Password Using by Channel Select Button

1 [1][2][3][4])

④ After Input Password Press Enter to See Menu

• Use the Up-Down button to move the cursor

to 7. Back Up icon .

Note : Move to Icon Start and press

Enter to CD burning after all

set .

CD-RW Proceed

St a rt

Ch4

1
2
3

4
5
6

•1. CD-RW Burner Display

• 2. Fill the start time in

• 3. Fill the end time in

• 4. Channel selection

• 5. Video backup selection

• 6. Audio backup selection

• 7. Event backup selection

• 8. Title backup selection

End Time

8

7

36

• Remote Agent

• System Requirement

① Main Board (CPU): Celeron 500-700(Minimum), Pentium 4 recommend
② OS: More than Windows 98,DirectX 7.0A
③ Memory (RAM): More than 128 M
④ VGA: Overlay YV12 Format Graphic Card

All Radeon, Nvidia (Above Geforce) Matrox (Above G400) Compatible Video Card

※ Above DIVX Codec 5.1 (When Use Media Player)

• DVR Remote Agent 1.0 Install

① Open CD-ROM Drive and Run DvrRemoteAgentSetup.exe and then Appear Setup Menu

② Close All Running Software and Press Next to Move Next Step

38

• Remote Agent

③ Ask designate Folder to Install DvrRemoteAgent 1.0,

Recommend Basic setup c:\program files:\DvrRemote Agent 1.0
Click Next

④ Showing Progress of Copy of Files

⑤ Appear DirectX 7.0a Install Menu. If DirectX Version Lower than 7.0a, Press Yes to Start Install

39

• Remote Agent

⑥ When Finishing Installation, System must be Restarted. Click ‘Yes’

⑦ Finish DvrRemoteAgent 1.0 Program Installation

40

• Remote Agent

7.1 Monitoring

7.1.1 Function Introduction

①

②

③

④

⑤

⑥

⑦

⑧

⑨

⑩

⑪

⑫

① Main Screen Image : Showing Present Surveillance Camera Image

② Camera Selection Button : Indicate Connected Camera No. & Select Image to Click Camera No.

③ Hide/Exit : Hide DVR Client Window or Exit Program

④ Time Output : Showing Present Time & Date

⑤ Search : Move to Search Mode to Play Video

Setup : Move to Setup to Change Network Setup or Option

⑥ I/D Selection : Select I/D to Connect Server

⑦ Connect : Connect Server (AVR 400S)

Disconnect : Disconnect from Server

⑧ Screen Division Selection : Change Screen Division Mode
⑨ Save by AVI file : Transmission Live Image Save by AVI File
⑩ Color Adjustment : Adjust Color of Live Transmission Image
⑪ PTZ Control Button : Control Camera PTZ & Focus
⑫ Exit : Exit DVR Client

41

• Remote Agent

7.1.2 Screen Division Selection

• 1*1 View : Showing One (1) Video which User Selected
(Selection Video by Camera Selection Button)

• 4*4 View : Quad Screen Division Mode

• Scenario View : One Large Screen Mode Showing One by One (1*1 View)

1 Depend on User Selection Time (Not Work Screen Division Mode)

• Full Screen View : Present Video Move to Full Screen Mode

7.1.3 P/T/Z Control

• P/T/Z Controller : Camera P/T/Z Control by Direction Keys

• FOCUS/ZOOM Select Button : Focus or Zoom Control by +,- Button

Mouse Double Click when Return Previous

*Mouse Double Click Make the Same Function as Full Screen.

• +,- Control Button : Focus or Zoom Control

7.1.4 Selection Network I/D

• Select I/D to Connect Server.

• I/D can be Add, Change, and Delete at Setup

Network Information Icon

• Click Network Information Icon, to See a

1 Popup Window for Connected Server I/D, 1

IP, and Port Information.

42

• Remote Agent

7.1.5 AVI File Conversion

7.1.6 Color Adjustment

• Click AVI Conversion Button to Start AVI File Conversion

• During AVI Conversion Showing a Message and before

1 Click ‘Stop” Save AVI File continuously

• Press ‘Stop’ to Open Designate File Name & Saving

1 Location, and Save AVI File

• Saved AVI File can Open Ordinary Moving Picture Player

• Moving Picture Player Codec Version is Above Divx 5.1.

• Click Controller Possible to Control Color

• Change Brightness, Contrast, Saturation from 0 to 100

• Click OK to Finish Changing Setup

43

• Remote Agent

7.2 Search Mode

7.2.1 Function Introduction

①

③

④

⑤

⑥

⑦

②

① Search Screen : Playing Selected Video

② Search Bar : Search & Indicate Camera Recording Situation by Time Bar

③ LIVE : Return to Watch Mode

SETUP : Open Setup to Change Network Setup or Option

④ Screen Division Selection : Change Playing Screen Division Mode

⑤ SEARCH Option : Backup Video or Search Event

⑥ Camera Selection Button : Select Camera at the 1*1 View

⑦ Quick Search : Find Image to Designate Date & Time

⑧ Search Controller : Control Playing Video

⑧

44

• Remote Agent

7.2.2 Search Method
①

⑤

②③ ④

① Indicate 0~24 Hour

② Indicate Recording Situation (Blue : No Record, Yellow : Recorded Image at the Time)

③ Search Bar : Select Video to Drag Mouse Search Controller in Recorded Area

④ Indicate Camera Channel to Confirm Camera Recording Situation

⑤ Refreshment Recording Information Situation Window by Camera Channel

⑥ If Connected Channel is 5 or More, Another Channel will be Scroll.

⑥

45

• Remote Agent

7.2.3 Search Option

③Save Image

①Backup

②Backup Play

① Backup – Backup Image from Server to Remote PC

• Backup Time : Designate Backup Time (Now or Later)

• Designate Backup Date & Time when Later

• Source :

Input Start Time & End Time.

• Channel : Check Camera Channel for Backup

⑤Log Search

⑥Event Viewer

④Print Image

Designate Backup Image Data Length to 1

•Press OK to Open Backup Status & Start Backup.

•When Finish Backup, Back Status Window Disappear & Backup Data Save at Hard Disk 1
Root Folder in Remote PC.

• Select All
Deselect All

46

• Remote Agent

① Showing Image (Possible to Only 1*1View Mode)

② Backup File Open to Play First Video

Ex. : ch02_04131730_04131735.rec ( Backup File for # 2 ch. Apr.13, 17H30M ~17H35M )

③ Indicate Present Playing Video Camera Channel No.

④ Indicate Present Time & Date and Possible to Search Time & Date

⑤ Search Controller, the Same Way of Previous Search

Tip

• Backup Play Setup in Search Mode is the Same as DVR Player,

so it can be Run Independently without Running Remote Program.

47

• Remote Agent

③ Save Image – Capture Image & Saving Image at Hard Disk or Removable Disk

• Click ‘Save Image’ Icon During Playing Video

• Designate File name, File Type (JPG,BMP), and Location and Press Saving

• Conversion and Saving Image from Remote Viewer

③ Print Image – Present Image Capture and Print Out Image

• During Play Video, Click ‘Print Image’

• After Selecting Printer, Start Image Printing

• Print Out Remote Viewer Image

48

• Remote Agent

③ Log Search – Find Video Centering around Event Log at Server

① Input Start Time and End Time at the Selected Date to Search Event

When Press Search Button, Event Output at the Below Window

② Indicate Event Log Order No. ( Max Event Log No. of 1 Page is 100 )

③ Indicate Event Occurred Camera No.

④ Indicate Event Occurred Time & Date

⑤ Indicate Event Detail Description

⑥ Move to Previous Page

⑦ Move to Next Page

⑧ Move to User Select Page

⑨ After Select Event, Move Search Bar in Search Mode

⑩ Return to Search Main to Play Event Image

49

• Remote Agent

④ Event Viewer – Showing Present Event in Server & Find Image

① Indicate Event Occurred Order No.

② Indicate Event Occurred Camera No.

③ Indicate Event Occurred Time & Date

④ Indicate Event Detail Description

⑤ After Select Event, Move Search Bar

1 in Search Mode

⑥ Return to Search Main to Play

1 Selected Event Image

①② ③

④

⑤⑥

50

• Remote Agent

9.3 Setting

①

①

②

②

③

④

⑤

⑥

⑦

⑧

⑨

⑩

7.3.1 Connection ID Setup

① ID Status : Indicate Present Saving ID & ID Information

② Input Name to Add or Amend ID

③ Input IP Address to Add or Amend Server

④ Indicate Port No.

⑤ Input ID for Connecting Server

⑥ Input Password for Connecting Server

⑦ Click to Input New ID Information

⑧ After Input All ID Information, Add ID Information at ID Status

⑨ After Amend All ID Information, Applying Change ID Information

⑩ Selected ID Delete at ID Status

③

④

Tip

• Initial ID & Password is ‘NETWORK’ & ‘1234’

51

• Remote Agent

7.3.2 Option Setting

① Control Screen Rotation Time in Scenario Mode at Watch Mode

(Possible to Setup from 1~300 sec.)

② Possible to Select Event Kind Plurally from Server. Remote Client Only can See Selected Event.

(System, HDD, Alarm, Video, REC)

③ Setup Print-Out Image of Information Display from Server (Name, Date, Resolution)

④ Designate Backup Image Saving Folder at Remote PC

52

•Time Table

■ DVR Storage Capacity Calculation (Based on 80GB HDD)

1. Calculation

1. Result

53

• PTZ Protocol List

■ PTZ Protocol List

※ Present DVR supply only PTZ/FOCUS/IRIS function. (Planning other feature)

54

• PTZ CONTROL

1. PTZ Control

PTZ/FOCUS

• Press PTZ/FOCUS Button to Open PTZ Menu at Right-Under Side and Control by

1 Search Controller

• When Press PTZ/FOCUS Button by Turns, Focus/Iris, Preset, Swing Menu will Appear at
the Right-Under Side and possible to Control by Search Controller.

PTZ CTL

UP

LEFT RIGHT

DOWN

Play

Fast

Forward

FOCUS/IRISCTL

UP

LEFT RIGHT

DOWN

PRESET

NUMBER:1

NUMBER CHANGE:UP/DOWN

SET:F1 GOTO:F2

SWING

MODE:PAN SWING

NUMBER CHANGE:UP/DOWN

FIELD CHANGE:LEFT/RIGHT

SET:F1 RUN:F2

Fast

Backward

Backward

Play

Search Controller

1.1 PTZ Control

① Control Camera Movement by ‘Faster’, ‘Slower’, ‘Backward Play’, ‘Play’ Button (Up,Down.Left,Right).

② Zoom In & Out by ‘Fast Backward’, ‘Fast Forward’ Button.

③ Keep Press Button Make Continuous Movement.

1.2 FOCUS/IRIS Control

① Control Iris by ‘Faster’, ‘Slower’ Button.

② Focus On by ‘Backward Play’, ‘Play’ Button.

③ Zoom In & Out by ‘Fast Backward’, ‘Fast Forward’ Button.

④ Keep Press Button Make Continuous Movement.

55

• PTZ CONTROL

8.1 PRESET Control

PRESET

NUMBER:1

NUMBER CHANGE:UP/DOWN

SET:F1 GOTO:F2

① By Preset Function, Possible to Setup Direction and Focus of PTZ Camera.

② After Selecting Position at PTZ Control Mode, Save Data at Preset Mode.

③ Setup ‘NUMBER’ from 1 to 128 by ‘Faster’ & ‘Slower’ Button.

④ Save by Front Panel Key No.1 Button or F1 Button on Remote Controller.

⑤ To Move to Saved Location, Press Front Panel Key Button No.2 or F2 Button on Remote Controller.

8.2 SWING Control

① SWING Function Dedicate Each No. of Saved Preset and Swing as Pan or

SWING

MODE:PAN SWING

NUMBER CHANGE:UP/DOWN

FIELD CHANGE:LEFT/RIGHT

SET:F1 RUN:F2

③ PAN SWING MODE : Rotate Left , Right Side.

TILT SWING MODE : Rotate Up, Down Side.
START PRESET : Select Starting Point. (1~128)
END PRESET : Select End Point. (1~128)
SWING TIME : Select Halt Time as Each Point. (1~64sec)
SWING SPEED : Select Moving Speed of Camera. (1~64)

Tilt.

② Changing Mode by Backward Play Button.

Changing Setup by Faster, Slower Button.

④ Save by Front Panel Key No. 1 Button or F1 Button on Remote Controller.

⑤ For Start SWING Mode, Press Front Panel Key No.2 or F2 Button on Remote Controller.

56

• Cross Cable Making Tip

■ Cross Cable Making Tip

1. LAN Plug

2. LAN Cable

A Part B Part

3. Connection Method

① Connect LAN Cable A part and LAN Plug by Order as One to One.

② Compare to LAN Cable B part & A part, Replace Order No.1 & 3, No. 2 & 6.

③ Connect LAN Cable B part No. 3 to LAN Plug No.1 and Connect the Next by Order.

57