Triplett Test Equipment & Tools 8150 User manual

CamView5 IP 1080P
HD CCTV Tester

USER MANUAL

8150

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Thank you for purchasing the IP camera tester. Please read the manual before
using the IP camera tester.
Please first read the「Safety Information」carefully in the manual.
The manual should be kept with unit in case reference is needed.
Keep the S/N label for after-sale service within warranty period. Product without
S/N label will be charged for repair service.
If there is any question or problem while using the IP camera tester, or damage to
the product, please contact our technical department.

（V01.00）

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

1. Safety information ................................................................................................1

2. IP Camera Tester Introduction ...............................................................................1

2.1 General.........................................................................................................1

2.2 Packing list...................................................................................................1

2.3 Function interface .........................................................................................2

3. Operation..............................................................................................................3

3.1 Installing the Battery..................................................................................... 3

4. IP camera test .......................................................................................................3

4.1 Power output ................................................................................................3

4.2 IPC Test pro .................................................................................................4

4.3 IP discovery................................ ................................................................ ..4

4.4 Rapid ONVIF test .........................................................................................5

4.5 Non-Onvif IP camera test..............................................................................8

5. Analog camera test................................................................................................9

5.1 CVBS...........................................................................................................9

5.2 Auto HD................................................................................................ .......9

5.3 CVI camera test ..........................................................................................10

5.4 TVI camera test ........................................................................................111

5.5 AHD camera test ........................................................................................12

6. Other functions ...................................................................................................12

6.1 Network tool ..............................................................................................13

6.2 RJ45 cable TDR test ...................................................................................14

6.3 Cable Tester ...............................................................................................14

6.4 PoE power / DC12V 3A power output .........................................................15

6.5 Update........................................................................................................16

6.6 File explorer ............................................................................................... 16

6.7 System Setting............................................................................................17

6.8 HDMI out (*Optional) ................................................................................19

7. Specifications .....................................................................................................19

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

1. Safety information

◆ The tester is intended for use in compliance with the local rules for electrical testers.

◆ To prevent the functional failure, the product should not come in contact with water.

◆ The exposed part of the tester should not be exposed to any liquids.

◆ During transportation and use, avoid vibration of the tester.

◆Do not leave the tester unattended while charging. If the battery becomes overheated, the tester should be immediately removed from the

electrical source. The tester should not be charged over 6 hours.

◆ Do not use the tester in high humidity conditions. Once the tester becomes damp, power off immediately.

◆ The tester should not be used in an environment with the flammable gas.

◆ Do not disassemble the instrument. There are no user replaceable parts inside.

◆ The instrument should not be used in an environment with strong electromagnetic interference.

◆ Do not touch the tester with wet hands.

◆ Do not use detergent to clean the unit. A dry cloth is recommended. If the dirt is not easy to remove, a damp cloth with water can be used.

2. IP Camera Tester Introduction

2.1 General

The 5-inch IPS touch screen IP camera tester is designed for maintenance and installation of IP cameras, analog cameras, TVI, CVI, AHD,
SDI/EX-SDI cameras, as well as testing 4K H.264 /4K H.265 camera by mainstream. The 1920x1080 resolution enables it to display a high
resolution image from the camera. The meter supports many ONVIF and analog PTZ controls. The combination of touch screen and touch
control keys make the IP camera tester very user- friendly.

2.2 Packing list

1) Tester

2) Adaptor DC12V 1A

3) Network cable tester

4) Lithium ion battery

5) BNC cable

6) RS485 cable

7) RJ45-BNC converter (Only for optional function cable tracer)

8) DC12V Power cable

9) Audio cable

10) Safety cord

11) Wrist belt

12) Tool bag

13) Manual

1

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

2.3 Function interface

1

Menu key

2

Confirm key

3

Return: Return or cancel while setting parameters of the menu

4

4x zoom the image display

5

LED light

6

The RS485 data transmission and received indicator lights red while the data is

being transmitted or received.

7

The power indicator lights red while the tester is powered on by the adapter

Top interface

Bottom interface

CCTV TESTER User Manual

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

2

CCTV TESTER User Manual

8

Press more than 2 seconds to turn on or off, short press to turn on or off the menu display

9

Micro SD card removeable, supports up to 32G

10

DC12V 3A power output, temporarily supply power to the camera

11

PoE power supply output/LAN test interface

12

HDMI output

13

Video image /AHD/TVI/CVI signal input（BNC interface）

14

LED lamp

15

DC 12V 1A charging interface

16

RS485 Interface: RS485communication for PTZ control

17

Audio input

18

UTP cable port: UTP cable tester port/ Cable tracer port (Optional)

3. Operation

3.1 Installing the Battery

The tester has a built-in lithium ion rechargeable battery. The battery should be disconnected for safety during transportation!
Prior to the use of the instrument, please remove the battery insulation paper. Pressing the key to power on /off the tester.

Notice: Please use the original adaptor and connected cable of the device!

When the battery icon is full or the charge indicator turns off, battery charging is completed.

Notice: When the Charge Indicator turns off, the battery is approximately 90% charged. Charging time can be extended for about

1 hour and the charging time under 12 hours will not damage the battery.

Notice: Press the key several seconds to restore the default settings when the instrument works abnormally.
Notice: While Charging, someone must be present.

4. IP camera test

4.1 Power output

Camera can be powered from the DC 12V/3A output or by Power over Ethernet.

3

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

4

4.2 IPC Test pro

Camera test often needs to open multiple apps, "IPC TEST PRO" app, using new technology and combing multiple functions into one APP,
can increase efficiency.

Application:

Support multi-segment IP address scan, can visually display camera brand, click IP address to display the image. Can supply the power to
PoE camera.
Real-time display network port connection status.
Use one key to connect camera test tool, browser can login and configure camera.
Batch activate Hikvision and Dahua cameras.

4.3 IP discovery

Press IP discovery , tester to auto-scan the entire network segment IP, as well as auto-modify the tester’s IP to the same network
segment with the scanned camera's IP. The meter auto-search the entire network segment IP, and auto-add the IP from different network
segments.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

5

Local IP: Tes ter’s IP address , Tester can auto-modify the tester’s IP to the same network segment with the scanned camera's IP .
Discovery IP: Connected tester equipment’s IP address . If the camera is connected to the tester directly, the tester will display the camera’s

IP address, if the tester connects to Local Area Network, it displays the current IP address.

Start: PING function, click "Start", can PING camera’s IP.
ONVIF: Rapid ONVIF Quick link.
IPC TEST: IPC TEST Quick link, Non-OnVIF IP camera test.

4.4 Rapid ONVIF test

Rapid ONVIF can disp lay 4K H.265/H.264 camera image by tester’ s mainstream.
The meter auto-scans all ONVIF cameras in different network segments. It lists cameras ’ name and IP address on the left of screen. Tester
can auto login camera and display camera image. Factory default uses admin password to auto login, if you modified the password, then
default uses the modified password to login.

Click the button “Refresh”, the tester will scan the ONVIF camera again. Click the newly displayed ONVIF camera on the “Device List”.
The tester will sh ow the IP camera’s relative information and settings.
Pop-up settings menu when you click the “setting” icon in the upper left corner.

Across network segments scan: After opening this function, Rapid ONVIF function can scan across network segments to scan camera’s
IP.

Auto Login: After opening this function, the tester can auto login camera and display camera image (The login default password is
"admin")

Video transmission protocol: UTP and TCP protocol.
Show focus Info: Focus Information.
View manual: Opens the Manual.
Restore Defaults: Restore “Rapid ONVIF” to default settings.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

6

Confirm: Save the modified parameters.

Click “MENU” icon to open camera setting.

While in the “Live video” menu, click “Video Menu” at the top right of the ima ge to access the following tools: Snapshot, Record, Photo,

Playback, Lens simulation, PTZ and Settings.
Network setting: Click “Network Set” to change the IP address. Some cameras cannot support change IP address, so there is no change

after saving.

When using the network video input, the tester supports resolutions up to 1080p, the input image remains clear after it is enlarged. This is
helpful to installers to ensure the IP camera’s video coverage and determine the IP camera’s install site.
Lens simulation: Simulate different lenses’ display area. Supported lens: “2.8/3.6/4/6/8/12/16/25mm", for choosing the su itable camera
lens.

OSD Menu: Select OSD and popup the OSD menu. include time, channel name and other optional items.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

After selecting a channel, you can edit the channel name, modify the display position, and switch the font size. Select “Content location ­Default location”. Select “Cus tomize” to arbitrarily adjust the channel name and display location.
Click “OK” to save the modification. Press return key or click any area on the screen to return to the previous interface.

Video files can play in the Video player on the main menu.

PTZ
Set preset position: Move the camera to preset position, enter the preset number on the bottom right corner to complete position preset.
Call the preset position: Select the preset number on the left, click "Call" to call preset.

PTZ speed set: Horizontal and Vertical speed set.

7

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

8

Doc: Click "Create document”, to create a test report document for the camera, . Click “Preview” to view the report document
Enter the camera test information, click "Create Document" to complete the report.
Click doc menu again, you can preview the report document.

Icons description: The description of function icons on the bottom toolbar.

4.5 Non-OnVIF IP camera test

Display image from the 4K H.265 camera by mainstream.

Note: Currently, the IPC Test App only sup ports some brand s’ spe cific IP cameras, these include specific models made by ACTI,

AXIS, Dahua, Hikvision, Samsung, and many more. If the camera is not fully integrated, please use the ONVIF or RTSP apps.

Local IP: This is th e tester’s IP address . Click “Edit” to enter “IP setting” and change the tester’s IP addres s settings.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

9

IP camera type: Click on the IP Camera type to select the manufacturer and model number of the connected IP camera.
Manual: Click IP camera type, list Honeywell, Kodak, Tiandy, Aipu-waton, ACTi, WoshiDA IP camera etc. If the brand has official

original protocols, pls select camera type, input IP camera address, username and password, click “official” to enter the camera image
display interface.
Stream code: When testing the camera via RTSP, you can select mains tream or sub stream to test (if camera’s RTSP ha s not been started,
it will prompt “auto match” fail, please switch to manual selection.
IP Camera's IP: Enter the IP camera’s IP address manually or click “Search” to auto-scan for the camera’s IP addres s. It is better to
directly connect the IP camera to the tester so the search results will only display the camera’s IP address .

IPC Port: When you select the IP camera type, it will default the camera’s port number and does not need to be changed.
After all settings are completed, click “Enter” to view the live v ideo .

5. Analog camera test

5.1 CVBS

Analog camera test and PTZ control.

Check and set the protocols, address, interface and baud, all must be consistent with the dome camera for the tester to work. After setting
the parameter, the tester can control the PTZ and lens.

5.2 Auto HD

Automatically recognize type and resolution of TVI/CVI/AHD camera and display an image.
Support coaxial PTZ and call OSD menu. Support CVBS and 8MP TVI/CVI/
AHD cameras. Select relative function on the right toolbar to operate, fu nctions including “Photos”, “Snapshot”, “Record”, “Playback”,
“PTZ”, “Set”.
Double tap on the screen to display in full screen.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

10

5.3 CVI camera test

When HD CVI signal input, the tester will display the image resolution at the top of the screen. Double tap on the screen to display the
image in full screen.
The tester supports resolution up to 3840 x 2160P 12.5/15 FPS.

（1） PTZ control

1.1 Coaxial PTZ control

Click the icon “PTZ” on the right toolbar to do the corresponding setting.
“Port”: select coaxial control

Enter PTZ address to perform parameters setting.

The PTZ address in the tester must be consistent with the dome camera or decoder for the IPC tester to work. After setting the

parameter, the tester can control the PTZ and lens.
Set preset position:
Move the PTZ camera to the preset position, tap it and input preset position number. Tap “Set position” to comp lete set preset position.
Call preset position:
Tap the preset position area, input preset position number. Tap “call position” to complete call pres et pos ition .

1.2 RS485 control

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

（2） Coaxial camera menu setting

Inp ut calling dome camera menu address code, you can press the key “Enter” or click the icon to call the dome camera menu.

set the parameters by

5.4 TVI camera test

When using an HD TVI signal input, the tester will display the image resolution at the top of the screen. Double tap on the screen to display
the image in full screen.
The tester supports resolution up to 3840 x 2160P 12.5/15 FPS.
Coaxial camera menu settings:
Tap icon “UTC”, select “MENU” to enter the dome camera menu.

11

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

12

Input calling dome camera menu address code, after finishing the parameter settings, you can press the key “Enter” or click the icon to
call the dome camera menu.

5.5 AHD camera test

When using an AHD signal input, the tester will display the image resolution at the top of the screen. Double tap on the screen to display
the image in full screen.
The tester supports resolution up to 3840 x 2160P 15 FPS.
(1) Coaxial PTZ control
UTC control: Select “PTZ or PTZ-2” (AHD camera has two different order, if the “PTZ” not working, pls go “PTZ-2” )

To use coaxial PTZ control with the AHD camera, no parameter settings are needed.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

13

6.1 Network tool

(1) IP address scan
Connect the cable to the LAN port, click icon to enter, set your IP address search range by changing the Start and End IP addresses.
Click the “Start” b utton to scan the IP address range. You can also input an IP address in the Port Number Scan to scan for o pen ports.

(2) PING Test

Application: PING testing is the most conventional network debugging tool. It is used for testing if the connected. IP camera or other
network equipm ent’s Ethernet port is working normally, and the IP address is correct.
It is normal that the first data packet will be lost when testing starts.

(3) Network test (Ethernet bandwidth test)

To use the Network tester, you will need two IP testers. One is used as a Server and the other as a Client. In order to communicate, both
devices must be on the same network segment.

(4) Port Flashing

Application:

The tester will send special signals to make the connected LAN port flicker at special frequency, which will aid the installer in finding the
connected Ethernet cable easily and quickly. This function can prevent mistakenly inserting or disconnecting the wrong cable and
interrupting network connection.

(5) DHCP server

Click on the DHCP icon to open the DHCP server app. Select the “Start” ch eck box at the top and make any desired changes to t he network
settings. Click “Save” to star t assigning dy namic IP addres ses fo r IP cameras and other networked devices. Click the “Refresh” button to
check your Client list.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

14

(6) Trace route

It is used to determine the path of the IP packet access target.
Note: Trace route testing results only for reference, for accurate test route tracking, use a professional Ethernet tester.

(7) Link monitor

This app is used to see if an IP address is occupied by other network devices. This will avoid new address conflicts.

6.2 RJ45 cable TDR test

Connect cable to tester’s LAN port, click icon “ ” to enter app.

Single test: Test cable status, length and attenuation.
Repeat test: Continue to test cable status, length and attenuation.
Status: After link-up, the screen displays “online”, or for an open circuit, the screen displays “open circuit”, if the cable pair has a short

circuit, the screen displays “sho rt circuit”.
Length: The max test length is 180 meters, when the cable is open circuit or short circuit, can test the cable length, if screen display
“online”, the testing res ult would not be accurate.
Cable quality test: Green is good quality cable, Yellow is poor quality cable, Red is water damaged cable, the attenuation value will be
displayed when a cable is over 10 meters.

Advanced Test: Test cable pair status, length, attenuation, reflectivity, impedance, skew and other parameters.
Attenuation reflectivity: After link-up, if the reflectivity value is 0, it is the best quality communication
Impedance: After link-up, if the impedance value is 100 Ω, it is the best quality communication, the range is generally in 85-135 Ω
Skew: After 1000M link up, if the skew value is 0ns, it is the best quality communication, if over 50ns, it will cause a Bit Error Rate in the

transmission.
Click “Help”, check the instruction of all parameters.

6.3 Cable Tester

Click icon to enter.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

Test LAN cable or telephone cable.
Connect LAN cable or telephone cable with the CCTV tester and cable tester. And then the connecting status, cable type and the sequence
of wires as well as the serial number of the cable tester kit will be displayed.
The number of the cable tester is 255.
Quickly detect the near-end, mid-end and far-end fault point of RJ45 cable connector

Cable test:

Tap "Diagram of the cable sequence", pop up the connection diagram of Straight-through cable and crossover cable. You can then create a
test report.

6.4 PoE / DC12V 3A power output

When the tester is turned on, the DC12V power output functions are automatically turned on.
To use the PoE Power Ou tput function, change the switch “ON” or “OFF”.
The IP camera needs to connect the LAN port before you turn on PoE Power. If the IP camera supports PoE, the PoE power is delivered via
pins 1, 2, 3, and 6 on the LAN port. The IP tester will disp lay “48V ON” at the top of the screen when the POE power is on.

Note:

15

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

16

1. Do not input power into the “DC12/3A OUTPUT” port.

2. Do not output the DC12V/3A power into the DC12V/IN port of the IP camera tester.

3. The IPC tester power output is close to 3A, if the IP camera’s power is over 3A, the tester will auto enter protection mode. Disconnect all
tester connections and then connect the tester with the power adaptor to continue.

4. Before turning on the PoE power output, make sure the IP camera supports PoE power. Otherwise it may damage the IP camera.

5. Before turning on PoE power output, connect the IP camera to the LAN port of tester.

6. Make sure the tester is full charged or more than 80% charged, or it will show “low power”, “not able to supply power”.

6.5 Update

Copy the downloaded update file to SD card "update" directory, if there is no directory, please create one.
Click the icon to open the Upd ate menu. Select “Local Update” to update via the SD card or select “Online Update” to c heck for

updates on the internet. If there are applications that need updating, the applications will be listed in the interface, click related applications,
update to the latest version.

Online update: Connect the Internet to update the apps.
App management: This can uninstall and open APP.

6.6 File explorer

Click “File” on the top toolbar, to select internal or external storage. Click on the upper right corner Icon “...”., to select other operations
from the menu or exit.

Browse

It includes Music, Videos, Pictures, Documents, zip file etc.to conveniently view and manage.

FTP server

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

17

You can choose internal or external SD card.
For other operation details, refer to FTP settings.

6.7 System Setting

Language: Select your desired language: English, Chinese, Korean, Russian, Italian, Polish, Spanish, French or Japanese.

Typewriting: You can select typewriting or install other typewriting:

Date/Time: Set the Date/time of the IP tester.
IP setting: Manually set the IP address, Subnet Mask, Default Gateway and DNS address or select “Dynamic allocation” to use DHCP. To
test multiple network segments, click “Advanced” and then click “Add” to enter another IP add res s for the IP tester.
WLAN Net: Turn WiFi off or on by pres sing the “Open the wifi” button. Once WiFi is turned on, click connected WIFI, to scan for

wireless networks in your area.

Select and pres s “WIFI” several seconds, to set static IP address.
Wi-Fi hotspot: Inpu t “SSID” name and “password”, and then click “ok” to create Wi-Fi hotspot.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

18

Brightness: Set the desired brightness of the IP tester and adjust the sleep time settings.
Volume: Set volume level
SD Card: Displays SD Card Capacity. You can also format the SD card or unmount it before removing it.
FTP server: Once the IP tester connects to a network, a computer can be used to read the SD card files via FTP.

Start the FTP server and then input the tester’s FTP address in the PC’s addres s bar. This will enable the PC to read, copy and edit the files
from the SD card without the use of SD card reader.

Version information: Shows applications version information, press any apps icon several seconds to uninstall.
Screen display rotation: Click on “Screen Rotation” to flip the IP tes ter’s display 180 degrees. This function is very convenient for the

user to connect the LAN cable on the bottom of the unit without having to flip the unit itself.
PTZ address scan: You can toggle the PTZ Address scan off or on before entering the “PTZ controller” app. This needs to be turned on in
order to use the PTZ Scan feature of the PTZ app.

Lock Screen: The meter default is not locked. You can choose password Lock screen, pattern Lock screen or “NO”.
Restore the factory settings: If the tester is restored to factory settings, all of your personal files and apps will be removed.
Power Off: Manually set Auto Off time (0-23h 59min).
Button mode selection: It can select button mode .

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

Model

8150 Camview5 Security Camera Tester

Display

New 5-inch IPS touch screen cctv tester, 1920*1080 resolution

Network port

10/100/1000M auto adjust, RJ45

WIFI

Built in WIFI, speeds150M, display wireless camera image

H.265 Main

stream test

New hardware decoding, 4K H.265/H.264 camera image
display by mainstream testing

IP discovery

Auto-scan the whole network segment camera IP

Rapid ONVIF

Search camera quickly, auto log in and display image from the
camera, activate Hikvision camera

Hik test tool

Batch activate Hikvision camera, display image from the
camera, modify channel, batch modify IP, username and
password parameters etc.

DH test tool

Batch activate Dahua camera, batch modify IP, modify
channel, username and password parameters etc.

IP camera type

ONVIF, ONVIF PTZ, Dahua IPC-HFW2100P, Hikvision
DS-2CD864-E13, Samsung SNZ-5200, Tiandy TD-NC9200S2,
Kodak IPC120L, Honeywell HICC-2300T, RTSP Viewer

Auto HD

Automatically recognize type and resolution of TVI/CVI/AHD
camera and display image. Support coaxial PTZ and call OSD
menu

HD-SDI/EX-SDI

camera test

*(Optional)

1 channel SDI in（BNC interface), resolution support upto
8MP: 720p 60fps / 1080p 60fps /1080i 60fps, EX-SDI:
2560x1440P /25/30FPS, 3840 x 2160P 25/30 FPS

CVI video signal

test

1 channel CVI input（BNC interface, resolution support 8MP
CVI camera test,
3840 x 2160P 12.5/15 FPS, 2880x1920P 20FPS,
2592x1944P 20FPS, 2560x1440p 25/30fps,
1920x1080p 25/30fps, 1280x720p 25/30/50/60fps,
UTC control and call OSD menu

TVI video signal

test

1 channel TVI input（BNC interface ), resolution support 8MP
TVI camera test,
3840 x 2160P 12.5/15 FPS, 2592x1944p12.5/20fps,
2688x1520p 15fps, 2560x1440P 18/25/30fps,
2048x1536p 18/25/30fps, 1920x1080p 25/30fps,

6.8 HDMI out

The built in HDMI output port can output live video from an analog or IP camera, recorded files, media files and images to HDTV
monitors. Connect an HDMI cable from the IP tester to an HDTV monitor at any time. It supports up to 3840x2160P 30FPS resolution.

7. Specifications

7.1 General Specifications

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

19

CCTV TESTER User Manual

20

1280x720p 25/30/50/60fps, UTC control and call OSD men

AHD video signal

test

1 channel AHD input（BNC interface）, resolution support 8MP
AHD camera test,
3840 x 2160P 15 FPS, 2592x1944p12.5/20fps,
2560x1440p 18/25/30fps, 2048x1536p 18/25/30fps,
1920x1080p 25/30fps, 1280x720p 25/30/50/60fps,
UTC control and call OSD menu

Analog video test

1 channel BNC Input, NTSC/PAL (Auto adapt)

Snapshot, Video
record and
playback

Capture current images and record live video as JPG file.
Media player will view photos and playback video

TesterPlay

screen projection: tester, mobile phone and PC display at the
same time

12V/3A power

output

Output DC12V/3A power to camera

PoE power output

48V PoE power output, Max power 25.5W

Theme

Self-define icons, desktop and application interface
background, modify interface sliding effect

Audio test

1 channel audio signal input

PTZ control

Support RS485 control, Baud 600-115200bps, Compatible with
more than 30 protocols such as PELCO-D/P, Samsung,
Panasonic, Lilin, Yaan, etc

Data monitor

Captures and analyzes the command data from controlling
device, also can send hexadecimal

UTP Cable tester

Test UTP cable connection status and display on the screen.
Read the number on the screen

Power

External

power supply

DC 12V 1A

Battery

Different item, battery is different, Built-in 7.4V Lithium ion
battery, 2600mAh/3350mAh

Rechargeable

After charging 3-4 hours, normal working time 5 hours or 6
hours (different item battery is different, the working time is
different

Parameter

Operation setting

OSD menu, select your desired language: English, Chinese,
Korean, Russian, Italian, French, Polish, Spanish, Japanese etc

Auto off

1-30 (mins)

General

Working

-10℃---+50℃

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CCTV TESTER User Manual

Temperature

Working

Humidity

30%-90%

Dimension/Weight

183mm x 110mm x 36.5mm /0.32kg

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

21