Page 1
User Manual
IRT150
Stem Thermometer with IR
Page 2
Introduction
Congratulations on your purchase of the Triplett IRT150 Stem Thermometer
with built in IR (Infrared) Thermometer. This instrument combines a noncontact infrared thermometer with stem type temperature probe, it can
measure the surface and inside temperature of object, it is a professional
thermometer and very useful for the food industry as well as wide variety of
other applications where external surface and internal temperature
measurements are needed.
Description
METER DESCRIPTION
1. IR Sensor
2. LCD Display
3. Scan/IR Measure/UP Button
4. Flashlight/DOWN Button
5. SET Button
6. Stem Probe
Page 3
LCD DISPLAY
1. IR Temperature Measurement Indicator
2. IR HOLD Icon
3. Temperature Units of Measure (°F/°C)
4. Temperature Measurement
5. Low Battery Indicator
6. Probe Temperature Measurement Indicator
7. HI/LOW ALARM Indicator
Operation
Basic Measurements
Power ON/OFF
IR Measurements
Press the SCAN/ Measure button and point it toward the surface to
be measured. The display will light if the battery is good. Replace
the battery if the display does not light.
While measuring, the scan symbol will appear in the upper left
hand corner of the LCD
Release the SCAN/Measure button and the HOLD display icon will
appear on the LCD indicating that the reading is being held.
The meter will automatically power down after approximately 7
seconds after the button is released.
Page 4
Probe Measurements
Swing the stem probe to the OUT position of the housing. The
meter will automatically turn ON and the LCD will display the probe
temperature.
While measuring, the probe measure icon will appear in the down
of the LCD
Fold the stem probe back to the IN position and the meter will turn
OFF.
Changing Temperature Units (°F/°C)
Press the set button five times, the C/F symbol will flash, then
press the “Light” button or “Meas” button to change the
Setting HI/LOW ALARMS
temperature unit.
Press the SET button once to set high alarm value, the “Hi”
symbol will flash
.
Press the “SCAN/ Meas/ UP ” Button to increase the high alarm
value.
Press the “Flashlight/DOWN” Button to reduce the high alarm
value.
Press the SET button twice to set high alarm ON/OFF,
Press the “SCAN/ Measure Button” or the “Flashlight Button to
disable the ON/OFF High Alarm.
Press the SET button three times to set low alarm value, the
“Low” symbol will flash, Press the “SCAN/ Meas/ UP” button to
increase the high alarm value,
Page 5
Press the “Flashlight/DOWN” button reduce the high alarm value.
Press the SET button four times to set low alarm ON/OFF.
Press the “SCAN/ Measure Button” or the “Flashlight Button to
disable the ON/OFF Low Alarm.
Battery Replacement
When the battery icon appears on the LCD, the batteries must be
replaced.
Open the battery cover, remove the battery, put in the new 2 x “AA”
battery, and then close the battery cover.
**Note**
Instrument is IP65, the probe can be cleaned however avoid condensation
build up around the infrared sensor area or it will affect the accuracy.
Page 6
Maintenance
Please clean the housing with soft cloth, do not let any liquid in to infrared
sensor region.
Please clean the probe before/after using the probe, or disinfect it with water
or cleaner.
Specifications
General Specifications
Data Hold Freezes displayed reading
Measurement Response <500ms
IR Distance to Spot ratio 4:1
IR Spectral response 8 to 14µm
IR Emissivity 0.95 fixed
Resolution 0.1
Repeatability Accuracy <1°C
Low battery indication Battery symbol appears on the LCD
Power supply (2) AA 1.5V Batteries
Operating conditions Meter: 0 to 50
Stem Probe (Thermistor) 3.0” (76mm)
Length
Dimensions / Weight Main instrument: (L) 2.5” x (W) 1.25” x (D) 1.0”
(L) 140mm x (W) 32mm x (D) 25mm
Weight 0.30 lb (4.8 oz.)
o
C (32 to 122oF); 80% RH max.
Page 7
Function
Range
Resolut
ion
Accuracy
Probe Temp
(Thermistor)
-40°F to 536°F
(-40°C to 280°C)
0.1°F/°
C
(4°F/2°C)
32°F to 392°F(0°C
to 200°C)
0.1°F/°C
1.0% reading +1.8°F
1.0% reading +1.0°C
IR Temp
-40 to 68°F
0.1°F/°
C
±5.4°F / 3.0°C
(-40 to 20°C)
68.0 to 536°F
0.1°F/°
C
±1.8°F/1.0%+1°C
(20 to 280°C)
Warranty
Triplett / Jewell Instruments extends the following warranty to the original purchaser of
these goods for use. Triplett warrants to the original purchaser for use that the products
sold by it will be free from defects in workmanship and material for a period of (1) one
year from the date of purchase. This warranty does not apply to any of our products
which have been repaired or altered by unauthorized persons in any way or purchased
from unauthorized distributors so as, in our sole judgment, to injure their stability or
reliability, or which have been subject to misuse, abuse, misapplication, negligence,
accident or which have had the serial numbers altered, defaced, or removed.
Accessories, including batteries are not covered by this warranty
Copyright © 2021 Triplett
www.triplett.com
Loading...