Triplett CD100 User Manual

User Manual

CD100

Conductivity / TDS / Salinity / Temperature Meter

- 0 -

Introduction

Thank you for selecting the Triplett CD100 Conductivity/Total Dissolved
Solids (TDS) / Salinity meter. With the CD100’s dynamic cell-constant
technology it is possible to measure a wide range of Conductivity, TDS,
and Salinity with the same electrode. Careful use and maintenance
provide years of reliable service.

- 1 -

Description

METER DESCRIPTION

1. Battery compartment cap

2. LCD Display

3. MODE / HOLD button

4. CAL / RECALL button

5. ON/OFF button

6. Electrode collar

7. Conductivity Electrode

LCD DISPLAY

1. Bar graph reading

2. Measurement Units

3. Main Display

4. RENEW Indicator

5. HOLD Indicator

6. RANGE Calibration

Indicator

7. Low Battery Indicator

8. Temperature Display

- 2 -

Powering On

The CD100 uses four (4) CR2032 Lithium Ion Batteries (included). If the
batteries are weak, the ‘Low Battery’ indicator appears on the LCD.
Press the ON/OFF key to turn the CD100 on or off. The auto power off
feature shuts the CD100 off automatically after 10 minutes of inactivity to
preserve battery life.

Getting Started

 Remove the cap from the bottom of the CD100 to expose the

conductivity electrodes.

 Before the first use or after storage, rinse the electride in water

and dry.

 For best results, calibrate for conductivity with a standard in the

expected range of the sample. For maximum accuracy calibrate from
low conductivity value standards to high value standards.

 Store dry.

- 3 -

Measurement Procedure

Sample Preparation:

1. For Conductivity, TDS or Salinity place the test
sample in a sample cup with enough depth (2.5cm
minimum) to cover the electrode. Stir the solution to
remove any air bubbles.

Measurement:

1. Press the ON button. ( and then “SELF CAL” will appear in the
display during the turn-on diagnostics)

2. Depress and hold the MODE/HOLD key to scroll to the desired
measurement mode.

3. Insert the electrode into the sample making sure that the electrodes
are completely submersed.

4. Slowly stir the solution with the electrode to remove air bubbles.

5. The meter will auto-range to the proper range and then display the
reading.

- 4 -

Changing Measurement Function

The meter can be set to measure Conductivity, TDS or Salinity.

To change the mode:

1. Press and Hold the MODE/HOLD button for 2 seconds and the

display will begin to scroll through the units.

µS (Conductivity); ppm S (Salinity); ppm (TDS); mg/l (TDS);

Note: The “HOLD” function cannot be on when changing the

measurement function. If “HOLD” is displayed in the lower left corner of
the display, briefly press the MODE/HOLD button to turn it off.

2. When the desired units are displayed, release the MODE/HOLD

button.

TDS Compensation Ratio

The TDS value is determined by multiplying a conductivity reading by a
known ratio factor. The meter allows for selecting a conversion ratio in
the range of 0.40 to 1.00. The ratio varies with the application, but is
typically set between 0.50 and 0.70.

Note: The stored ratio will briefly appear in the lower temperature
display when the meter is first turned on, or when changing
measurement function to TDS.

Note: In the Salinity mode the ratio is 0.40 to 0.60 auto.

To change the ratio, while in the TDS measurement mode (ppm or mg/l):

1. Press and release the CAL/RECALL button twice in

succession. The stored ratio will appear in the
display.

2. Press the MODE/HOLD button to increase the ratio value in steps of 0.01.

3. When the desired ratio is displayed, press and
release the CAL/RECALL button to store the
value and return to the normal mode.

4. If no buttons are pressed for 5 seconds, the
meter returns to measure mode.

- 5 -

Storing Readings

1. Press the MODE/HOLD button to store a reading.
The storage location number will be displayed on
the lower display, while the main display shows
the stored reading. The meter will enter the HOLD
mode and the “HOLD” indicator will appear.

2. Press the MODE/HOLD button again to exit the
HOLD mode and return to normal operation.

3. If more than 25 readings are stored, previously
stored readings (starting with number 1) will be
overwritten.

Recalling Stored Readings

1. Press the CAL/RECALL button and then press the MODE/HOLD
button. A location number (1 through 25) will briefly appear and then
the value stored in that location will appear. The displayed units will
flash, indicating that the storage recall mode is active.

2. The last stored reading will be displayed first. Pressing and releasing
the MODE/HOLD button will scroll through the stored readings one at
a time. The location number is displayed first, followed by the reading
stored in that location.

3. To exit the storage mode, press the CAL/RECALL button and the
meter will return to normal operation, after displaying “End”.

Clear Stored Memory

With the unit on, press and hold ON/OFF for 4 seconds. “CLr” will be
briefly displayed when the memory is cleared.

- 6 -

Changing Temperature Units

To change the displayed temperature units (oC or oF):

1. With the unit OFF, press and hold down the CAL/RECALL button.

2. With the CAL/RECALL button depressed momentarily press the

ON/OFF button. When “SELF CAL” appears in the display release the
CAL/RECALL button. The unit will power on with temperature

displayed in the new units.

Data Hold Mode

Press the MODE/HOLD button to hold (freeze) a reading in the display.
The meter will enter the HOLD mode and the “HOLD” indicator will
appear.

Note: This also stores the reading.

Press the MODE/HOLD button again to return to normal operation.

Auto Power OFF

The auto power off feature automatically shuts the meter off 10 minutes
after the most recent button press.

Auto Power OFF Disable

To disable the Auto Power Off feature:

1. Turn the unit on.

2. Press CAL/RECALL once (Quickly)

3. Immediately and simultaneously press the MODE/HOLD and ON/OFF

buttons for approximately 2 seconds, until “oFF” is briefly displayed

To disengage this feature, turn the unit off with the ON/OFF button. The
next time the unit is powered up, Auto Power OFF mode will be engaged
again.

- 7 -

Low Battery Indication

When the batteries become weak the “ ” icon will appear in the
display. Refer to the Maintenance section for battery replacement
information.

Measurement and Display Considerations

If the unit appears to be locked (display frozen). It is possible that the
Data Hold mode has been inadvertently accessed by pressing the
MODE/HOLD button. (“HOLD” will be displayed in the bottom left of the
LCD.) Simply press the MODE/HOLD button again or turn the meter off
and then on.

For maximum accuracy, allow sufficient time for the temperature of the
probe to reach the temperature of the sample before calibrating. This will
be indicated by a stable temperature reading on the display.

Reset Calibration Data

Follow this procedure to clear all calibration data from the meter.
Resetting the calibration data may be necessary when new calibration
solutions are used or accuracy of measurements is in question.

1. Turn off the meter.

2. Press and Hold the Cal/Recall and Mode/Hold buttons.

3. Momentarily press the On/Off button, as soon as the display comes
on, release all 3 buttons.

4. The display will show “dFLt rSt” (default reset) and all of the
calibration data will be erased. If “dFLt rSt” does not appear, retry the
procedure.

5. Proceed to the calibration routine for Conductivity.

Calibration - Conductivity

Meter accuracy verification should be performed on a periodic basis.
Once per month is the recommended cycle for normal use. If calibration
is required, a conductivity standardizing solution must be obtained. The
meter can be calibrated in any or all of the three ranges. Standardizing
solutions of 84µS/cm, 1413µS/cm or 12.88mS/cm (12,880µS/cm) are
used for the automatic calibration recognition procedure. No other
calibration values are permitted.

- 8 -

Calibration is always done in conductivity mode. Since salinity and TDS
values are calculated from conductivity values, this procedure also
calibrates the salinity and TDS ranges.

Fill a sample cup with the standardizing solution.

1. Turn the meter ON and insert the electrode into the solution. Tap or
move the electrode in the sample to dislodge any air bubbles.

2. Press and hold the CAL/RECALL button (approximately 2
seconds) until “CAL” appears in the lower (temp) display. The main
display will start flashing.

3. The meter will automatically recognize and calibrate to the
standardizing solution. The display will briefly indicate “SA”, End
and then return to the measurement mode after a calibration.

4. Note: The “SA” will not appear if the calibration fails.

5. The “range calibrated” symbol will appear in the display for each
range that is calibrated during that power on cycle.

Low range, 84µS/cm

Medium range, 1413µS/cm

Note: Each time the calibration mode is entered all calibration symbols on
the display are cleared, but only the calibration data for the currently
calibrated range is replaced. The other two ranges keep the existing
calibration data, just the symbols are removed. Calibration of all three
ranges must be performed during one power on period for all three range
calibration symbols to appear.

See Reset Calibration Data to clear all calibration data from the meter.
Note: The meter allows for a 1, 2 or 3 point calibration. If calibration is

done for more than one point the lowest value standard should be done
first to obtain the best accuracy.

High range, 12.88mS/cm (12,880µS/cm)

Considerations and Techniques

Do not touch the inner surfaces of the conductivity electrodes. Touching
the surface of the platinized electodes may damage and reduce the life
of the probe.

Store the electrode dry, in the storage cap.

- 9 -

Always rinse the electrode in de-ionized water between measurements
to avoid cross contamination of the sample. Double rinsing is
recommended when high accuracy is required.

Specifications

Display 2000 count LCD with Bargraph
Conductivity ranges 0.0 to 199.9µS

200 to 1999µS

2.00 to 19.99mS
TDS ranges 0.0 to 99.9ppm or mg/L
(Variable ratio) 100 to 999ppm or mg/L

1.00 to 9.99ppt or g/L
Salinity range 0.0 to 99.9ppm

100 to 999ppm

1.00 to 9.99ppt
TDS Ratio 0.40 to 1.00 adjustable
Salinity Ratio 0.40 to 0.60 auto
Conductivity ATC 2.0% per oC
Conductivity ATC Range 32.0°F to 140oF (0.0°C to 60.0oC)
Temperature Range 32.0°F to 194oF (0.0°C to 90.0oC)
Temperature Resolution 0.1 up to 99.9, 1 >100
Temperature Accuracy ±1.8°F; 1°C
Accuracy Conductivity: ±2% full scale

TDS: ±2% full scale

Salinity: ±2% full scale
Measurement Memory 25 tagged (numbered) readings
Low battery indication ‘ ’ appears on the LCD
Power Four (4) CR2032 Lithium Ion Batteries
Auto power off After 10 minutes (override available)
Operating conditions 23°F to 122oF (-5°C to 50oC)
Dimensions 1.5 x 7.8 x 1.5” (38 x 198 x 38 mm)
Weight 3.3 oz (95 g)

- 10 -

Maintenance

Battery Replacement

1. Twist off the battery compartment cap

2. Replace the four (4) 2032 batteries observing polarity.

3. Replace the battery compartment cap

Electrode Replacement

1. To remove an electrode, unscrew and completely remove the

electrode collar (turn the collar counter-clockwise to remove).

2. Gently rock the electrode from side to side, pulling it downwards,

until it disconnects from the meter.

3. To attach an electrode, carefully plug the electrode into the

meter socket (note that the electrode connector is keyed,
ensuring proper connection).

4. Tighten the electrode collar firmly enough to make a good seal

(a rubber gasket seals the electrode with the meter).

- 11 -

Cleaning Recommendations

brush, maximum of

thoroughly

When cleaning the probe, take care not to scratch or damage the
sensing surface or the platinized electrode surfaces.

Contaminant Cleaning Solution Instructions

Water soluble
substances

Grease & Oil Warm water and

Heavy grease & Oil Alcohol Maximum of 5 minute

Lime and hydroxide
coatings

Deionized water Soak or scrub with a

soft brush. Rinse
thoroughly with DI
water and dry.
Soak or scrub with a

household detergent

10% acetic acid Soak until coating

soft
10 minutes. Rinse
thoroughly with DI
water, and dry.

soak, scrub with a soft
brush. Rinse
with DI water, and dry.

dissolved, maximum of
5 minutes. Rinse
thoroughly with DI
water, and dry.

Warranty

Triplett / Jewell Instruments extends the following warranty to the original purchaser
of these goods for use. Triplett warrants to the original purchaser for use that the
products sold by it will be free from defects in workmanship and material for a period
of (1) one year from the date of purchase. This warranty does not apply to any of our
products which have been repaired or altered by unauthorized persons in any way or
purchased from unauthorized distributors so as, in our sole judgment, to injure their
stability or reliability, or which have been subject to misuse, abuse, misapplication,
negligence, accident or which have had the serial numbers altered, defaced, or
removed. Accessories, including batteries are not covered by this warranty

Copyright © 2021 Triplett

www.triplett.com

- 12 -