Model 9200-A Mini AC Clamp-On
Instruction Manual
1. Triplett Model 9200-A Features
• Economical, Compact AC Current Clamp-On
• Easily Fits in Shirt Pocket!
• Measures from 0 to 300 Amps AC in Two Ranges
• Simple, Two Button Operation
• Large, 3 3/4 Digit, 4000 Count Display
• Autoranging
• Data Hold
• Overrange Indication
• Auto Power Off
• Low Battery Indication
• Powered by one 3V Battery
• Carrying Case, Wrist Strap and Battery included
• 1 Year Limited Warranty
2. Model 9200-A Specifications
Display: 3 3/4 Digit, 4000 Count LCD, 12mm high
Operating Principle: Dual Slope Integration
Range Selection: Autoranging
Overload Indication: “OL” is displayed when input
exceeds 405 A
Low Battery Warning: “BAT” symbol is displayed
Sampling Rate: 2.5 times per second
Data Hold: Holds reading when DH Button
Overload Protection: AC Current, 400A AC for 60
Seconds Max
Operating Temperature & Humidity: 32° F to 104° F,
Storage Temperature & Humidity: 14° F to 122° F,
Safety / Agency Approvals: CE Mark,
Auto Power Off: Power turns off after 12 min. of
Battery: 1 - 3 Volt CR2032 Button Type (Included)
if product was turned on in the package.
If so, replace battery with a fresh one.
Battery Life: 100 Hours Continuous Operation
Conductor Size: 27mm Max (1.14 “)
Dimensions: 5.8” (L) x 1.8” (W) x 0.8” (H)
Weight: 3.4 oz.
is pressed
less than 80% non-condensing
less than 70% non-condensing atmosphere
IEC 1010-1 Overvoltage CAT III 300VAC,
Class II and EMC Test Passed
non-use
Note: Power consumption is reduced in
Auto Power Off. For maximum battery
life, turn the power off manually.
Note: The installed battery may be depleted
egnaRnoituloseRycaruccAtnerruCtupnI.xaM
A00.04Am01
A0.003Am001
:noitcetorPdaolrevO:noitcetorPdaolrevO
:noitcetorPdaolrevO:noitcetorPdaolrevO xaMsdnoceS06rofCAA004
:noitcetorPdaolrevO
:esnopseRycneuqerF:esnopseRycneuqerF
:esnopseRycneuqerF:esnopseRycneuqerF tgd5ddaA4.0~0*,zH06~zH05
:esnopseRycneuqerF
tnerruCCA
*)tgd5±gdr%8.1(±
ycaruccaevobaot%5.1dda,zH005~zH04
A003
)eniLV003xaM(
3. Front Panel, Display Details
Figure 1
3.1 Model 9200-A LCD
~ : Alternating Current (AC)
BAT : Low Battery Warning
AUTO : Autoranging
DH : Data Hold
A : Amps
APO : Auto Power Off
3.2 On/Off and Data Hold Buttons
Momentarily press the ON/OFF Power Button to turn
the unit on or off.
To save a reading in the display, momentarily press the
DH (Data Hold) Button. The DH symbol will appear in
the LCD display. To clear the saved reading, momentarily press the DH button again.
3.3 Clamp Head
When measuring AC Current, open Clamp Head by
pressing the Lever and clamp around a single conductor to be tested.
NOTE: You cannot measure the current to an appliance by clamping around its power cord. You must
clamp around only the HOT or NEUTRAL conductor,
not the entire cord.
3.4 Safety Guard
For safety, fingertips must NOT go past the Safety
Guard.
4. SAFETY PRECAUTIONS
Electrical measurements can be very dangerous without proper knowledge of the risks involved. To reduce
the possibility of injury, the following precautions must
be observed. However, no written warnings or cautions
can prevent the misuse, abuse, or careless operation
of the product. Safe measurements are only possible if
the user follows safety guidelines.
SAFETY CONSIDERATIONS
Read all WARNINGS and CAUTIONS in this manual,
especially those identified with the symbol,
prior to using the product. Failure to do so may
result in product damage or injury to the user.
WARNING!!!
AC Power Lines are very dangerous and without
proper knowledge, can be lethal to the user. Power
Lines that are considered High Energy Circuits are
especially dangerous. High Energy Circuitry is
usually regarded as any circuitry capable of
supplying over 4000 watts to a load before a safety
device (like a fuse) interrupts the circuit. Arcs of an
explosive nature can develop in this type of
circuitry, causing serious injury or even death.
The Triplett Model 9200-A is not designed for use
in High Energy Circuitry!
4.1 Warnings
Condition of Meter
Make sure that the meter is not damaged in any way
(cracks, missing parts, etc.) before every measurement.
Make sure that the body is free of dust, grease, and
moisture.
Figure 2
High Energy Circuits
This product is not intended for use on High Energy
Circuits such as Distribution Transformers, Bus Bars,
Large Motors. etc., which are very dangerous.
Maximum Voltage and Current
The maximum current is 300A AC. The maximum voltage is 300V AC. Do not attempt to measure current
that might exceed the specified value or current on lines
whose voltage exceeds 300 VAC.
Safety Guard
Do not let fingers go over the Safety Guard when gripping the Model 9200-A.
4.2 General Warnings and Cautions
Warning 1 - Do not let children use this instrument
or those who are unable to recognize the dangers of
electrical measurements.
Warning 2 - Do not make measurements while bare-
footed. This greatly increases the possibility of electrical shock.
Warning 3 - Do not attempt to clean the case with
any harsh solvents. If necessary, use mild detergent
and water.
Warning 4 - Avoid severe mechanical shock or vi-
bration, extreme temperature or very strong magnetic
field.
Warning 5 - Remove the battery when not in use for
an extended period of time. A low battery might leak
electrolyte and corrode the internal components.
5. Measurement Procedures
5.1 Preparation For Use
1. Instruction Manual
Prior to use, read this Instruction Manual carefully and
acquaint yourself with the specifications and functions
of the instrument. Especially read and observe carefully the Safety Precautions in Section 4.
2. Battery
One 3V CR2032 battery is installed in this instrument.
When the battery is low and “BAT” is displayed on the
LCD, open the Battery Cover and replace the battery
with a fresh one. Refer to section 6.1 Battery Replacement for details.
3. Overrange Indication
If the Input Value exceeds approximately 405 Amps
AC, “OL” is displayed on the LCD.
WARNING!!!
DO NOT attempt to make any measurements that
might exceed 300A AC (max 300V Line)
4. Auto Power Off
Approximately 12 minutes after the operation of either
button on the product, the unit will go into a ‘sleep’
mode to reduce its power consumption. In the sleep
mode, the LCD will turn off, but the unit is still operating at low power. To turn the unit off completely (which
maximizes the battery life), press the ON/OFF button
before the unit goes to sleep, or if the unit is sleeping,
press the ON/OFF button to turn the unit on, then press
it again to turn the unit off.
5. Symbols
The following International Symbols shown on the instrument and in this instruction manual aid in the safe
operation of the instrument.
: Caution (Refer to Instruction Manual)
~ : Alternating Current (AC)
: Earth Ground
: Double Insulation
5.2 AC Current (~A) Measurements
WARNING!!!
Maximum Voltage of AC Current Line is 300V AC.
DO NOT attempt to make any current
measurements that might exceed
300A AC, the Maximum Input Current.
Prior to use, read this Instruction manual
carefully and acquaint yourself with the
specifications and functions of the instrument.
Especially, read and observe carefully the
Safety Precautions in Section 4.
1. Momentarily press the ON/OFF button to turn the
power on.
WARNING!!!
For safe measurements, fingertips must be
placed behind the Safety Guard of this instrument.
DO NOT touch any part of the Power Line
or the Electrical Circuit.
2. Open Clamp Head by pressing the Lever and clamp
around a single conductor. See Figure 3.
NOTE: You cannot measure the current to an appliance by clamping around its power cord. You must
clamp around only the HOT or NEUTRAL conductor,
not the entire cord.
3. Read the current on the LCD.
4. To capture the reading, activate the Data Hold by
momentarily pressing the DH button.
6. Maintenance
6.1 Battery Replacement
WARNING!!!
Remove Clamp Head from the circuit being
measured before attempting to replace the battery.
1. If the battery is low and “BAT” is displayed on the
LCD, replace the battery.
2. Turn the Model 9200 off.
3. Remove the screw on the Battery Cover on the back
side of the instrument.
4. Replace the low battery with a fresh one - 3V CR2032
type.
NOTE: A small screwdriver or pair of tweezers may be
helpful in removing the depleted battery. See Figure 4"
5. Replace the Battery Cover and screw. Refer to
Figure 4.
Figure 4
6.2 Periodic Test and Calibration
Periodic tests and calibration are necessary to ensure
safe and accurate measurements. It is recommended
that the instrument be checked and calibrated once each
year and/or after it is repaired.
TRIPLETT PRODUCT
RETURN INSTRUCTIONS
In the unlikely event that you must return your
Triplett equipment for repair,the following steps
must be taken.
1) Call 1-800-TRIPLETT to obtain a Return
Material Authorization (RMA) number from
Customer Service.
2) Enclose a copy of the original sales receipt
showing date of purchase.
3) Clearly print the RMA number on the outside
of the shipping container.
4) Return to: Triplett / Jewell Instruments
850 Perimeter Road
Manchester, NH 03103
ATTN: Repair Dept.
Be sure to include a full description of the problem,
and a telephone number, street address, or email
address, where you can be contacted, and a return
address where the meter can be shipped to upon
repair.
Triplett One Year Limited Warranty
Triplett / Jewell Instruments warrants instruments and test
equipment manufactured by it to be free from defective
material or workmanship and agrees to repair or replace
such products which, under normal use and service, disclose
the defect to be the fault of our manufacturing, with no charge
within one year of the date of original purchase for parts
and labor. If we are unable to repair or replace the product,
we will make a refund of the purchase price. Consult the
Instruction Manual for instructions regarding the proper use
and servicing of instruments and test equipment. Our
obligation under this warranty is limited to repairing,
replacing, or making refund on any instrument or test
equipment which proves to be defective within three years
from the date of original purchase.
This warranty does not apply to any of our products which
have been repaired or altered by unauthorized persons in
any way so as, in our sole judgment, to injure their stability
or reliability, or which have been subject to misuse, abuse,
misapplication, negligence, accident or which have had the
serial numbers altered, defaced, or removed. Accessories,
including batteries and fuses, not of our manufacture used
with this product are not covered by this warranty.
To register a claim under the provisions of this warranty,
contact Triplett / Jewell Instruments’ Customer Service
Department for a Return Authorization Number (RMA) and
return instructions. No returned product will be accepted
without an RMA number. Upon our inspection of the
product, we will advise you as to the disposition of your claim.
ALL WARRANTIES IMPLIED BY LAW ARE HEREBY
LIMITED TO A PERIOD OF ONE YEAR FROM DATE OF
PURCHASE, AND THE PROVISIONS OF THE W ARRANTY
ARE EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES
EXPRESSED OR IMPLIED.
The purchaser agrees to assume all liability for any damages
and bodily injury which may result from the use or misuse
of the product by the purchaser, his employees, or others,
and the remedies provided for in this warranty are expressly
in lieu of any other liability Triplett / Jewell Instruments may
have, including incidental or consequential damages.
Some states (USA ONLY) do not allow the exclusion or
limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. No
representative of Triplett / Jewell Instruments or any other
person is authorized to extend the liability of Triplett / Jewell
Instruments in connection with the sale of its products
beyond the terms hereof.
Triplett / Jewell Instruments reserves the right to discontinue
models at any time, or change specifications, price or design,
without notice and without incurring any obligation.
This warranty gives you specific legal rights, and you may
have other rights which vary from state to state.
Figure 3
5. When measurements are finished, remove Clamp
Head from the conductor.
Triplett Model 9200-A Mini AC Clamp-On Meter
Cat. No.: 9200
Made in China
84-878
Loading...