• Use caution when attempting to evaluate if a dangerous voltage is present. The meter will not read
)airetircIITAC,tupnixamstloV006(EGATLOVCD
EGNAR NOITULOSER YCARUCCA
TUPNI
ECNADEPMI
DAOLREVO
NOITCETORP
Vm004Vm1.0
±tgd3+gdr%8.0
M0001>Ω
CD/CAV006
V0.4V100.0
M01Ω
V04V10.0
V004V1.0
V006V1±tgd3+gdr%0.1
)airetircIITAC,tupnixam,eniszH06,stloV006(EGATLOVCA
EGNAR NOITULOSER YCARUCCA
YCNEUQERF
ESNOPSER
DAOLREVO
NOITCETORP
Vm004Vm1.0±tgd5+gdr%5.1
zH004-04CD/CAV006
V0.4V100.0
±tgd5+gdr%2.1V04V10.0
V004V1.0
V006V1±tgd5+gdr%5.1
M01:ecnadepmItupnI Ωsegnarllano
ECNATSISER
EGNAR NOITULOSER YCARUCCA NOITCETORPDAOLREVO
004Ω1.0Ω
±tgd3+gdr%0.1
CD/CAV006
K0.4ΩK100.0Ω
K04ΩK10.0Ω
K004ΩK1.0Ω
M0.4ΩM100.0Ω
M04ΩM10.0Ω± tgd5+gdr%0.3
TNERRUCCD
EGNAR NOITULOSER YCARUCCA NOITCETORPDAOLREVO
004µA1.0µA
±tgd5+gdr%0.2
tsaF
esuFV052/A5.0
0004µA1µA
Am04Am10.0
±tgd5+gdr%5.1
Am004Am1.0
TNERRUCCA
EGNAR NOITULOSER YCARUCCA
YCNEUQERF
ESNOPSER
DAOLREVO
NOITCETORP
004µA1.0µA
±tgd5+gdr%5.2
zH004-04
tsaF
esuFV052/A5.0
0004µA1µA
Am04Am10.0
±tgd5+gdr%0.2
Am004Am1.0
)YLNOEGNAROTUA(YCNEUQERF
EGNAR NOITULOSER YCARUCCA
.XAM
YTIVITISNES
DAOLREVO
NOITCETORP
)nimzH01(zH05zH10.0
±tgd2+gdr%20.0smrV5CD/CAV006
zH005zH1.0
zHK5zHK100.0
ELCYCYTUD
EGNAR YCARUCCA YCNEUQERF.XAM
%9.99ot1.0±tgd2+gdr%2
zHK01
)YLNOEGNAROTUA(ECNATICAPAC
EGNAR NOITULOSER YCARUCCA EMITESNOPSER
DAOLREVO
NOITCETORP
Fn04Fn10.0±tgd51+gdr%0.5
ces2.xorppA
CD/CAV006
Fn004Fn1.0
±tgd01+gdr%5.2
4µF100.0µF
04µF10.0µFces5.xorppA
001µF1.0µF± tgd51+gdr%0.3ces01.xorppA
TSETEDOID
YALPSIDXAMTNERRUCTSETYCARUCCA NOITCETORPDAOLREVO
V999.0Am5.0ot1.0%01.xorppACD/CAV006
TSETYTIUNITNOC
YALPSIDXAMEGATLOVTSETTNERRUCTSETXAMYCARUCCA
DAOLREVO
NOITCETORP
9.993ΩV5.0.xorppAAm1.xorppA±tgd3+gdr%0.1CD/CAV006
03nahtssel@sdnuoSrepeeBΩ).xorppA(
AC voltage if it is set to DC, nor will it read DC if it is set to AC. For example, if the meter is set to
200VDC, it will not measure a dangerous AC voltage, even if the probes are inserted into a household
AC wall outlet.
TRIPLETT
• Do not touch the metallic portion of one test lead if the other test lead is connected to a live circuit.
The current from the live circuit may pass through the meter and appear on the unconnected test
Model 2030-C
Pocket-Sized DMM
INSTRUCTION MANUAL
lead. Failure to observe this warning may result in user injury.
• Remove the batteries when the meter may be left unused for longer than 1 month. Chemical leakage
from the batteries could damage the meter, leading to user injury.
• Do not use the meter if there is evidence of chemical leakage from the batteries. Leakage could
damage meter and lead to injury of user.
• Do not modify the meter. Changing the design may make the meter unsafe and may result in injury to
INTRODUCTION
The Triplett 2030-C Pocket Digital Multimeter uses modern technology to provide the user with a convenient, compact, feature packed measuring instrument. The 2030-C measures AC and DC Voltage
and Current, tests Diodes, measures Resistance, Frequency and Capacitance and incorporates a Continuity Beeper. It features Autoranging or Manual ranging in the voltage and resistance measuring modes,
as well as a battery saving Auto Power Off mode. These abilities make the 2030-C useful in the lab,
shop, car, or home.... by the Electrician, Technician, or Hobbyist.
FEATURES
• Autoranging Pocket-Sized DMM
• 3 3/4 Digit, 4000 Count Display
• AC/DC Volts to 600V
• AC/DC Current to 400mA
• Resistance to 40MΩ
• CAT II 600V Rating on Voltage Ranges
• Capacitance Test to 100µF
• Frequency Range to 10KHz
• Duty Cycle
• Diode Check
• Continuity Beeper
• Relative Mode
• Data / Range Hold
• Auto Power Off
• Low Battery Indicator
• Hard, Protective Case
• One Year Warranty
WARNING!!!
This meter is NOT to be used to measure High Energy circuits (power circuitry fused at
greater than 4KW, such as distribution circuits, power entrance circuits, etc.)
or circuits classified by CE as CATEGORY III (CAT III).
SAFETY RULES AND WARNINGS
• Read all instructions in this manual before using this meter.
• Prior to using the meter in any situation which could result in injury to the user, in order to verify that
the meter is functional and producing a valid reading, test the meter on a circuit(s) known to have
the user.
• Do not attempt to use meter when no display is present on LCD. Doing so may damage the meter
and/or injure the user.
• Use Caution when the meter is in the HOLD mode. In this mode, the meter will not display a new
reading, and consequently, may not indicate the presence of dangerous voltages. i.e. If the meter is
in HOLD and is displaying 1 volt, the meter will continue to display 1 volt, even though 500 volts is
applied to the meter’s test leads.
• When replacing the batteries, dispose of the depleted batteries in accordance with any prevailing
safety or environmental regulations.
SPECIFICATIONS
Display . . . . . . . . . . LCD, Resolution: 3 3/4 digit, 4000 count
Ranging . . . . . . . . . A total of 36 ranges / functions (see following specs)
Polarity . . . . . . . . . . Automatic, minus (-) sign indicates negative polarity
Overrange . . . . . . . LCD displays “OL”
Battery . . . . . . . . . . 2 - 1.5 Volt, LR-44 or SR-44, Triplett part number 37-51
Battery Life . . . . . . . Approx 150 hours typical
Dimensions . . . . . . . 3.2 x 4.8 x 0.8 inch
Weight . . . . . . . . . . . Approx 4 oz.
Agency Approvals . . CE CAT II 600 (on voltage ranges only)
potentials equivalent to the potential that is to be measured. For example, before using the meter to
determine if an AC power line is energized with 120VAC, test the meter on a line known to be
energized with 120VAC.
• Do not exceed the maximum voltage limitations of this meter (see product specifications). Doing so
may damage the meter and/or injure the user.
• When using this meter in schools and workshops, responsible teachers or skilled personnel must
control the usage of this meter.
• Follow the recommendations of any Trade Organizations or Regulatory Agencies whose scope
encompasses the use of this meter.
• Do not use this meter with its battery cover open, its rear case open, or with parts removed.
• Do not open this meter for maintenance without first disconnecting the test leads from all external
circuitry.
• Repairs and maintenance must only be carried out by qualified service personnel or qualified electri cians /technicians who know the dangers of, and the safety rules applicable to this type of equipment.
• Use caution when measuring circuits containing capacitors. Capacitors can store dangerous levels of
electricity, even when the circuitry which they are in has been disconnected from its power source.
• Use caution when working with voltages above 25 volts AC or 35 volts DC. Such voltages may cause
a life threatening electrical shock.
• This meter is not for use by children.
• Always set the meter to the appropriate range or mode before connecting it to the circuitry to be
tested.
• Never attempt to make voltage measurements with the Function switch set to DIODE
Continuity Beeper
meter and/or injure the user.
• Do not rotate the Function switch with the test leads connected to the circuitry to be tested. Doing so
may damage the meter and/or injure the user.
• Before using the meter, examine both the meter and the test leads for damage. Do not use the meter
if damage (damaged insulation, exposed metal, cracked case, burnt smell, etc.) is evident.
•
locations with steam, explosive gases or dusts. Doing so may damage the meter and/or injure the user.
• Do not use the meter if either the meter or the test leads are wet, either from exposure to the weather,
or after cleaning the case of the meter. Doing so may cause injury to the user.
• Avoid usage near strong magnetic fields (magnets, loudspeakers, transformers, motors, coils, relays,
contactors, electromagnets, etc.). The meter may display readings that are in error, causing the user
to misinterpret the hazards present. For example, the meter may indicate a low voltage when high
voltages are actually present.
•
etc.). The meter may display readings that are in error, causing the user to misinterpret the hazards
Do not use this meter to make measurements in adverse environments such as rain, snow, fog, or
Avoid usage near strong electrostatic fields (high voltage power lines, televisions, computer monitors,
present. For example, the meter may indicate a low voltage when high voltages are actually present.
• Avoid usage near strong RF fields (radio or television transmitters, etc.). The meter may display
readings that are in error, causing the user to misinterpret the hazards present. For example, the
meter may indicate a low voltage when high voltages are actually present.
• Do not touch the tips of the test leads when making a measurement. Do not touch live circuitry when
making a measurement.
• Do not apply more than 600 volts DC/AC rms between the test leads and the earth ground. Doing so
may damage the meter and/or injure the user.
• If there is any doubt about the condition of the meter (i.e. safe vs unsafe), remove the meter from
service and secure it in a location that will prevent its unintentional use.
• Do not use the meter if it does not appear to work correctly on all ranges and in all modes.
• Do not use the meter if it has undergone long-term storage under unfavorable conditions.
• Do not use the meter if it may have been damaged in transport.
• Do not attempt immediate use of the meter when bringing if from a cold environment to a warm
environment. Condensation of water, inside and outside of the meter, may produce dangerous
measuring conditions. Allow the meter to warm to room temperature before using.
• Do not use meter in condensing atmospheres. That is, do not use meter in conditions where ambient
temperature and humidity could cause condensation of water inside of meter. Doing so may cause
injury to the user.
• Do not continue to use meter when the “low battery” symbol
may be in error and lead the user to believe that no hazard exists, when in fact, dangerous voltages
or currents may be present.
, Frequency (Hz, KHz), or Capacitance . Doing so may damage the
_
+
is displayed. The displayed reading
, OHM Ω,
Size: 0.42" (10.6 mm) high
Annunciators: mV, V, Ω, K Ω, M Ω, µF, nF, AC, Hz, KHz, µA, mA
_
, ,
+
, H , and AUTO
MAKING MEASUREMENTS, GENERAL INFORMATION
TRIPLETT
To make a measurement, open the lid of the meter and rotate the rotary switch to the position appropriate to the quantity to be measured. If appropriate, press the pushbuttons to further define the desired
type of measurement. The AutoRanging feature of the meter will automatically select the range which
will produce the most accurate reading. Alternately, the user may manually select the range by pressing
CONTINUITY BEEPER
WARNING!!! REMOVE ALL POWER FROM THE CIRCUIT BEING TESTED. FOLLOW
APPROPRIATE PROCEDURES TO REMOVE CHARGE FROM ANY CAPACITORS IN THE CIRCUIT.
NEVER CONNECT THE TEST LEADS TO ANY SOURCE OF VOLTAGE
and releasing the RANGE button. Note the position of the decimal point, and the annunciator (like mV
or V) to determine the selected range. Note: The Capacitance (
) and Frequency (Hz) measurement
functions are Autorange only.
The selected range should be higher than the expected input value. For example, if a 120 Volt AC
household circuit is to be measured, set the meter to the 400 Volt AC range. If a 12 Volt car battery is to
be measured, set the meter to the 40 Volt DC range. If the level of the quantity being measured is
unknown, always set the meter to the highest appropriate range.
To reset the meter from Manual operation to AutoRange operation, press and hold the RANGE button
until the meter beeps and AutoRange operation commences (the AUTO annunciator will turn on).
NOTE: Carefully remove the test leads from their storage compartment on the meter and extend them
to their full length. Observing the proper polarity (red is positive and black is negative), and following all
applicable safety rules, connect the test leads to the circuit to be measured. Read the voltage on the
LCD display.
If the meter continuously overranges while attempting to measure voltage, immediately disconnect the
test leads from the circuit being measured. Reset the meter to an appropriate range and try making the
measurement again, or discontinue using the meter to perform the test. The quantity that you are trying
to measure may exceed the capability of this meter, and continued attempts at making a measurement
may result in damage to the meter or user injury.
When finished making measurements, carefully fold the test leads back into the storage compartment,
starting with the leads themselves, and finishing by capturing the tips of the probes with the flip cover
and folding it down into the compartment. Before closing the lid of the meter, verify that the test leads
are completely enclosed in the storage compartment, and set the rotary switch to the OFF position.
When the knob is set to OFF, it aligns with the “power slot” in the lid of the case, allowing the lid to be
closed. This feature guarantees that the meter is turned off when the lid is closed, thereby extending
the battery life.
HOLD
A reading appearing in the LCD can be held by pressing and releasing the HOLD button. The HOLD
annunciator
will appear in the display when this feature is activated. This feature allows the user to
H
take a measurement for a few seconds, press the HOLD button, and “capture” the reading on the LCD.
The HOLD mode is released by pressing the HOLD button again, pressing a different button, or by
turning the rotary switch.
WARNING!!! DO NOT TURN ROTARY SWITCH IF AN INPUT IS APPLIED TO THE METER
AUTO POWER OFF
The 2030-C incorporates an Auto Power Off feature designed to lengthen the battery life. If the switch
and the buttons are undisturbed over a period of time, the meter will automatically “go to sleep”. Once
the meter has “gone to sleep”, a press of one of the buttons or turning the rotary switch will “wake it
up”. The time out interval for the 2030-C is approximately 30 minutes.
WARNING!!! DO NOT TURN ROTARY SWITCH IF AN INPUT IS APPLIED TO THE METER
Follow the procedures outlined in the Safety Rules and General Information
1) Set the rotary switch to BEEPER (
Press the SELECT/REL
Select the BEEPER
2) Connect the test leads to the circuit to be tested for continuity.
3) If continuity exists, i.e. the resistance between the test leads is less than about 30 Ohms, the
beeper will sound, and the LCD display will indicate the resistance of the circuit (up to 400 Ohms).
CAPACITANCE MEASUREMENT
WARNING!!! FOLLOW APPROPRIATE PROCEDURES TO REMOVE CHARGE FROM ANY
CAPACITORS TO BE TESTED. PERFORMING TESTS ON CHARGED CAPACITORS MAY RESULT
IN DAMAGE TO THE METER OR USER INJURY. NEVER CONNECT THE TEST LEADS TO
ANY SOURCE OF VOLTAGE WHEN THE METER IS SET TO THE CAPACITANCE MODE.
Note: This meter is not intended to perform in-circuit testing of capacitors.
1) Set the rotary switch to
2) Connect the test leads to the capacitor to be measured, observing the proper polarity of the
leads (if important in your application).
3) Read the displayed capacitance on the LCD.
NOTE 1: The response time of the capacitor measurement mode lengthens as the capacitance being
tested increases. On the highest range (100µF), response time can be 10 seconds or longer.
NOTE 2: The 2030-C will not determine if a capacitor is “good” or “bad”...... it only measures the value
of the capacitor. A capacitor which measures OL may be Shorted or Leaky.
FREQUENCY AND DUTY CYCLE MEASUREMENT
WARNING!!! THE MAXIMUM INPUT VOLTAGE IS 600 VOLTS AC
Follow the procedures outlined in the Safety Rules and General Information
1) Set the rotary switch to Hz.
2) Connect the test leads to the signal to be measured.
3) Read the displayed frequency on the LCD.
4) To measure Duty Cycle, press the SELECT / REL button. To return to frequency measurement, press
the SELECT / REL button again.
REL (RELATIVE) MODE
The 2030-C incorporates a useful REL Mode that works in the Capacitance and Voltage measuring
functions. It does not work in the OHMS, DIODE TEST, CONTINUITY, FREQ, µA, or mA functions.
AC and DC VOLTAGE MEASUREMENTS
WARNING!!! THE MAXIMUM INPUT VOLTAGE IS 600 VOLTS AC/DC
Follow the procedures outlined in the Safety Rules and General Information
Note: The ultra-hi input impedance of the meter may cause the meter’s reading to change randomly
until the test leads are connected to a signal source.
1) Set the rotary switch to the AC ( V
If using the AutoRange feature, proceed to Step 2). If using the MANUAL range mode, refer to the
instructions given under MAKING MEASUREMENTS, GENERAL INFORMATION.
2) Connect the test leads to the circuit to be measured, observing the proper polarity of the leads.
) or DC ( V ) voltage mode as desired.
To “null out” the residual capacitance of the 40nF range (which can be as high as 150 digits), turn the
rotary switch to the CAP range, observe the LCD reading, and then press the SELECT/REL
The displayed reading should drop to 00.00nF. Proceed to measure capacitance as described previously.
Similarly, residual readings on the V AC and V DC ranges can be nulled out, or, for special testing
purposes, actual AC or DC voltage readings can be nulled to zero, and changes in the input quantity
observed as positive and negative deviations from zero.
BATTERY REPLACEMENT
WARNING!!! PRIOR TO CHANGING THE BATTERIES, DISCONNECT THE TEST LEADS FROM
ANY CIRCUITRY THAT THEY MAY BE HOOKED TO AND STORE THE LEADS IN THE CASE.
3) Read the displayed voltage on the LCD.
4) If the minus (-) sign appears (in DC Mode) the positive test lead is connected to a negative polarity.
1) Remove the battery cover on the rear of the meter’s case by removing two screws.
2) Remove the batteries and dispose of them in an approved manner.
AC and DC CURRENT MEASUREMENTS
WARNING!!! THE MAXIMUM INPUT VOLTAGE IS 250 VOLTS AC/DC
Follow the procedures outlined in the Safety Rules and General Information
1) Remove power from the circuit to be tested and connect the test leads of the meter in series with the
circuit, observing polarity as appropriate.
DO NOT INSERT THE METER INTO CIRCUITS WHERE THE OPEN CIRCUIT VOLTAGE EXCEEDS
250V AC/DC. DOING SO MAY DAMAGE THE METER OR RESULT IN USER INJURY.
2) Set meter to appropriate current range (µA or mA). Press the SELECT/REL ∆ button to select AC
or DC measurement.
3) Apply power to circuit being tested and observe the reading on the LCD.
4) If the minus (-) sign appears (in the DC mode) the positive test lead is connected to a negative
polarity.
5) Remove power from the circuit being tested before disconnecting the test leads of the meter.
RESISTANCE MEASUREMENTS
WARNING!!! REMOVE ALL POWER FROM THE CIRCUIT BEING TESTED. FOLLOW
APPROPRIATE PROCEDURES TO REMOVE CHARGE FROM ANY CAPACITORS IN THE CIRCUIT.
NEVER CONNECT THE TEST LEADS TO ANY SOURCE OF VOLTAGE
WHEN THE METER IS SET TO ANY OF THE “OHM” RANGES.
Follow the procedures outlined in the Safety Rules and General Information
Note: This meter is not intended to perform in-circuit testing of resistors.
1) Set the rotary switch to the OHMs mode ( Ω ).
If using the AutoRange feature, proceed to Step 2). If using the MANUAL range mode, refer to the
instructions given under MAKING MEASUREMENTS, GENERAL INFORMATION.
2) Connect the test leads to the circuit to be measured, observing the proper polarity of the leads (if
important in your application).
3) Read the displayed resistance on the LCD.
DIODE TEST
WARNING!!! REMOVE ALL POWER FROM THE CIRCUIT BEING TESTED. FOLLOW
APPROPRIATE PROCEDURES TO REMOVE CHARGE FROM ANY CAPACITORS IN THE CIRCUIT.
Follow the procedures outlined in the Safety Rules and General Information
Note: This meter is not intended to perform in-circuit testing of diodes.
1) Set the rotary switch to DIODE (
NEVER CONNECT THE TEST LEADS TO ANY SOURCE OF VOLTAGE
WHEN THE METER IS SET TO DIODE TEST.
Ω ).
3) Insert new batteries, observing proper polarity.
4) Replace the battery cover.
FUSE REPLACEMENT
WARNING!!! PRIOR TO CHANGING THE FUSE, DISCONNECT THE TEST LEADS FROM
ANY CIRCUITRY THAT THEY MAY BE HOOKED TO AND STORE THE LEADS IN THE CASE.
1) Remove the battery cover on the rear of the meter’s case by removing two screws.
2) Remove the Wrist Strap from the case.
3) Gently pry the case open, starting at bottom of the case, where the Wrist Strap was attached.
Remove back of case. Note how Lid attaches to case.
4) Replace the fuse.
5) Reassemble.
STAND / WRIST STRAP
The Wrist Strap can also be used to make the lid of the 2030-C act as a Stand. Flip the lid open, and
with it positioned behind the 2030-C, run the handle of the Strap through the slot in the lid, adjusting
the handle so that it does not pull back through the slot. Set the meter down . . . the lid acts as a stand.
The Triplett Corporation warrants instruments and test equipment manufactured by it to be free from defective material or workmanship
and agrees to repair or replace such products which, under normal use and service, disclose the defect to be the fault of our manufacturing, with no charge within one year of the date of original purchase for parts and labor. If we are unable to repair or replace the
product, we will make a refund of the purchase price. Consult the Instruction Manual for instructions regarding the proper use and
servicing of instruments and test equipment. Our obligation under this warranty is limited to repairing, replacing, or making refund on
any instrument or test equipment which proves to be defective within three years from the date of original purchase.
This warranty does not apply to any of our products which have been repaired or altered by unauthorized persons in any way so as, in
our sole judgment, to injure their stability or reliability, or which have been subject to misuse, abuse, misapplication, negligence, accident or which have had the serial numbers altered, defaced, or removed. Accessories, including batteries and fuses, not of our
manufacture used with this product are not covered by this warranty.
To register a claim under the provisions of this warranty , return the instrument or test equipment to Triplett Corporation, Service Department, One Triplett Drive, Bluffton, Ohio 45817, transportation prepaid. Upon our inspection of the product, we will advise you as to the
disposition of your claim.
ALL WARRANTIES IMPLIED BY LAW ARE HEREBY LIMITED TO A PERIOD OF ONE YEAR FROM DATE OF PURCHASE, AND THE
PROVISIONS OF THE WARRANTY ARE EXPRESSL Y IN LIEU OF ANY OTHER WARRANTIES EXPRESSED OR IMPLIED.
The purchaser agrees to assume all liability for any damages and bodily injury which may result from the use or misuse of the product
by the purchaser, his employees, or others, and the remedies provided for in this warranty are expressly in lieu of any other liability
Triplett Corporation may have, including incidental or consequential damages.
Some states (USA ONLY) do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. No representative of Triplett Corporation or any other person is authorized to extend the liability of
Triplett Corporation in connection with the sale of its products beyond the terms hereof.
Triplett Corporation reserves the right to discontinue models at any time, or change specifications, price or design, without notice and
without incurring any obligation.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
TRIPLETT ONE YEAR LIMITED WARRANTY
Press the SELECT/REL ∆ button ( Ω ) while observing the annunciators on the LCD
display. Select the DIODE mode of operation.
2) Connect the test leads to the circuit to be measured, observing the proper polarity of the leads.
3) Read the diode voltage on the LCD.
Triplett Corporation One Triplett Drive Bluffton, OH 45817
800-TRIPLETT FAX: 419-358-7956 www.triplett.com
WHEN THE METER IS SET TO DIODE.
Ω ).
∆
button while observing the annunciators in the LCD display.
mode of operation.
.
TURN THE METER OFF AND CLOSE ITS LID.
TURN THE METER OFF AND CLOSE ITS LID.
∆
button.
PN 84-834
Rev B
Loading...