Initial Testing
Instruc tion Manual
Continuity Test
Introduction
The Triplett FireFly Rapid LAN Mapping
Tool is an innovation in mapping and
identication technology. A simple patent
pending concept leads to unparalleled
speed in ID’ing large numbers of unmarked
LAN cables during the installation phase of
large LAN systems. While the FireFly can be
used on any size LAN system,it saves the most
time for installers on systems exceeding
25 ports. The basic FireFly comes with
100 Remotes, or ‘Flies’, and is upgradeable to
use a limitless number of optional Flies.
In addition to rapid mapping, the FireFly
includes a Reverse Polarity test, and a
Short/Continuity test. An included adapter
allows the FireFly to function
as a standalone Continuity tester.
While developed primarily for LAN systems,
the FireFly will work on any wiring that
terminates with RJ-45 connectors. Cables
with RJ-45 connectors, once seen mostly
in LAN applications, are becoming industry
standards for numerous other wiring
installations. Some examples include
Telephone, Alarm, Security, Video, Audio, and
even Lighting. As the uses continue to
expand, the FireFly stands ready to meet
the industries mapping and ID
requirements.
Startup
Installing / Replacing Battery:
Remove the single screw on the back
of the FireFly’s case. Carefully remove
the front panel and install / replace the
9 volt battery. Replace the front panel
and reinstall screw.
The FireFly sends a test signal to a Fly to make
it ash. This is easily demonstrated by
plugging a Fly into the RJ-45 jack on the
FireFly. The FireFly detects the presence of the
Fly, ashing the green Remote Detected LED
on the FireFly, and the green LED in the Fly
itself. Although it can’t be easily
demonstrated, if the connection to the Fly is
reversed in polarity, the Fly will ash red
(The FireFly will continue to ash green, since
it still detects the presence of the Fly). If a Fly
is not connected to the FireFly, the green
LED will not ash. If the FireFly detects a Short
instead of a Fly, the red Short / Continuity LED
will turn on and a beeper will sound. An
adapter test lead is provided to allow the
FireFly to be used as a Continuity tester.
Logistics
It is best to use the FireFly with 2 persons,
one in the IT room and one who will travel
to the location of each far end jack / plug.
They should be in communication with each
other, typically by cell phone or walkie talkies.
Mapping Procedure
a) Terminate both ends of the wires/cables
with RJ-45 connectors.
b) In the IT room, attach the terminated
cables to a patch panel.
c) Install Flies in all jacks being used in the
panel
d) One person stays in the IT room and
observes the Flies.
e) The other person travels to each far end
location and connects the FireFly to the
RJ-45 there. He should see the green
Remote Detected LED ash on the FireFly.
The person in the IT room should
immediately see a Fly ashing green. Mark
the ends of the cable appropriately.
Remove the Fly from the panel to indicate
that that jack is done. If FireFly
does not ash the green LED, the cable is
defective or a Fly is not connected to this
cable. If the Fly ashes red, the cable is
connected to the FireFly, but the polarity
is reversed.
f) Move to next location and test, etc. etc.
The FireFly can be used as a standalone
continuity tester. Simply plug the provided
alligator test lead into the FireFly’s RJ-45
connector, and connect the clips to the
item that will be tested for continuity. If
continuity is found, the FireFly’s red
Short / Continuity LED will light and
the beeper will sound.
Specications
Maximum Test Distance
Determined by wire resistance.
Workable up to 1000 Ohms.
(equiv to 15,000ft of 24ga CAT5 LAN cable)
Battery
Standard 9 volt battery
Battery Life
Approx 50 hours continuous use (ID mode)
In actual typical use, battery lasts several
months.
Test Current
Less than 40mA
Continuity Threshold
Approx 1V
Size
FireFly: 2.45” x 3.75” x 1.2”
Fly: 0.5” x 0.6” x 1.5”
Complete Kit in Box: 2.5” x 5.75” x 10.25”
Weight
1.25 lbs (FireFly with 100 Remotes)
PN: 3290
Warranty on reverse
Note: Replace battery when LEDs becomes
dim or product operates erratically.
Manchester, NH USA triplett.com 800-triplett
Triplett One Year Limited Warranty
Triplett warrants instruments and test equipment manufactured by it to be
free from defective material or workmanship and agrees to repair or replace
such products which, under normal use and service, disclose the defect to be
the fault of our manufacturing, with no charge within one year of the date of
original purchase for parts and labor. If we are unable to repair or replace the
product, we will make a refund of the purchase price. Consult the Instruction
Manual for instructions regarding the proper use and servicing of instruments
and test equipment. Our obligation under this warranty is limited to repairing,
replacing, or making refund on any instrument or test equipment which proves
to be defective within one year from the date of original purchase.
This warranty does not apply to any of our products which have been repaired
or altered by unauthorized persons in any way so as, in our sole judgment, to
injure their stability or reliability, or which have been subject to misuse, abuse,
misapplication, negligence, accident or which have had the serial numbers
altered, defaced, or removed. Accessories, including batteries and fuses, not of
our manufacture used with this product are not covered by this warranty.
ALL WARRANTIES IMPLIED BY LAW ARE HEREBY LIMITED TO A PERIOD OF
ONE YEAR FROM DATE OF PURCHASE, AND THE PROVISIONS OF THE WAR
RANTY ARE EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES EXPRESSED
OR IMPLIED.
The purchaser agrees to assume all liability for any damages and bodily injury
which may result from the use or misuse of the product by the purchaser,
his employees, or others, and the remedies provided for in this warranty are
expressly in lieu of any other liability Triplett may have, including incidental or
consequential damages.
Some states (USA ONLY) do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion may not apply
to you. No representative of Triplett / Jewell Instruments or any other person
is authorized to extend the liability of Triplett in connection with the sale of its
products beyond the terms hereof.
cations, price or design, without notice and without incurring any obligation.
which vary from state to state.
Loading...