Triple S SV-12 Operating & Maintenance Instructions

WET/DRY VACUUM

MODEL

SV-12

OPERATING & MAINTENANCE

INTRODUCTION INSTRUCTIONS

This operator’s book has important information for the use
and safe operation of this machine. Read this book care­fully before starting the machine. Keep this book and tell
all operators to read the book. If you do not follow the
instructions, you can cause an injury or damage equipment,
furniture or buildings.

For additional information refer to the Triple S website
www.triple-s.com or write to:
Triple S

2 Executive Park Drive
Billerica, MA 01862

Carefully inspect all components to ensure that there is no
concealed freight damage. If such damage is discovered,
file a “CONCEALED DAMAGE REPORT” immediately
with the delivering carrier.

READ THIS BOOK

The contents of this manual are based on the latest product
information available at the time of publication. Triple S
reserves the right to make changes or improvements to its
machines without notice.

FOR YOUR CONVENIENCE, RECORD THIS
IMPORTANT INFORMATION:

MODEL_______________________________

SERIAL NUMBER______________________

PART NUMBER ________________________

DATE PURCHASED ____________________

IMPORTANT SAFETY INSTRUCTIONS

READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS

BEFORE USING THIS MACHINE!

WARNING! To reduce the risk of fire, electric shock, or injury:

1. You must be trained to operate this machine. This machine is to be operated for its intended use
only.

2. Do not operate this machine unless it is completely assembled.

3. Always use a three-wire electrical system connected to the electrical ground. For maximum protection
against electrical shock, use a circuit that is protected by a ground fault circuit interrupter. Consult
your electrical contractor.

4. To prevent electrical shock: Always remove the electrical plug from the electrical outlet before perform­ing any repairs, maintenance or cleanup and when leaving the machine unattended.

5. To prevent electrical shock: Keep the machine surface dry; Do not subject to rain; Store the machine
in a dry building area; Clean the machine with a dry cloth only.

6. Machines can cause an explosion when near flammable materials and vapors. Do not use or store
this machine with or near fuels, grain dust, solvents, thinners, or other flammable materials. Do not
use flammables to clean this machine.

7. Maintenance and repairs must be done by a qualified or authorized person.

8. If the machine is not working as it should, has been dropped, damaged, left outdoors, or dropped into
water, return it to a service center.

9. To avoid damage to the machine’s electrical cord, always lift the machine over the cord. Do not run
the machine over the electircal cord.

10. Make sure all labels, decals, warnings, cautions and instructions are fastened to the machine.

Grounding Instructions

This machine must be grounded. If it should malfunction or break down,
grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This machine is equipped with a cord having an
equipment-grounding conductor and grounding plug. The plug must be
inserted into an appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.

WARNING - Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. Check with a qualified electrician
or service person if you are in doubt as to whether the outlet is properly
grounded. Do not modify the plug provided with the machine - if it will not
fit the outlet, have a proper outlet installed by a qualified electrician.

This machine is for use on a nominal 120-volt circuit, and has a grounded
plug that looks like the plug illustrated in figure A. A temporary adapter
that looks like the adapter illustrated in figures B and C may be used to
connect this plug to a 2-pole receptacle as shown in figure B if a properly
grounded outlet is not available. The temporary adapter should be used only
until a properly grounded outlet (figure A) can be installed by a qualified
electrician. The green colored rigid ear, lug, or the like extending from
the adapter must be connected to a permanent ground such as a properly
grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by the
Canadian Electrical Code

EXTENSION CORDS

Use only three-wire 16/3 or larger gauge approved extension cords that have
three-prong grounding type plugs and three-pole receptacles that accept the
appliance’s plug. Replace or repair any damaged cords or plugs.

When servicing, refer to authorized person only. Use only identical
replacement parts.

NOTE: Do not use adapters shown in figures B & C in Canada

2

OPERATING PROCEDURES

WARNING! For the safe operation of this machine
follow the instructions given in this booklet and the
training given by your supervisor. Failure to do so can
result in personal injury and/or damage to machine and
property!

DO NOT OPERATE MACHINE IN AN EXPLOSIVE
ENVIRONMENT!

WARNING! NEVER USE THIS MACHINE TO PICK
UP VOLATILE OR EXPLOSIVE MATERIALS.

OPERATION

To prepare the machine for operation, make sure it is of the
correct voltage and properly assembled. If in doubt, ask
your supervisor.

FOR DRY PICK-UP:

“Dry” refers to material such as dust, dirt, debris and dry
foam shampoo.

1. Release the clamp on the side of the tank and head as­sembly. Lift the head assembly off and set it aside.

2. Then lift the cloth filter assembly out of the collector
tank. Clean the cloth filter if needed (reference the
“Maintenance” section).

3. Empty the collector tank of all dust and debris. If the
debris is wet, empty and dry the inside of the tank
thoroughly.

FOR WET PICK-UP:

“Wet” refers to liquids such as water, scrub solutions and
detergents; NOT volatile or explosive materials.

1. Release the clamp on the side of the tank and head as­sembly. Lift the head assembly off and set it aside.

2. Then lift the cloth filter assembly out of the collector
tank. Store the filter assembly for future, dry pick-up
use. DO NOT REINSTALL.

3. Empty the collector tank of all dust and debris. Also

wipe the inside of the collector tank to remove cling
ing dust.

4. Check the float shut-off device on the lower portion of
the head assembly. The float should have free move­ment. When the recovered liquid soilage reaches the
collector tank capacity, the float will rise to shut off the
air flow, stopping the liquid recovery. This prevents
damaging overflow and signals the operator when to
empty the collector tank.

5. Replace the head assembly and fasten the clamp. Attach
the hose, wand and floor tool of choice (reference page

5).

6. Plug the power cord into a 115-volt, 60 cycle grounded
outlet.

7. Turn the machine’s motor on by pressing the rocker
switch which is located on the head assembly.

4. Place the cloth filter assembly back into the collector
tank. Check for a good seal around the outer filter lip
and tank rim.

5. Replace the head assembly and fasten the clamp. Attach
the hose, wand and floor tool of choice (reference page

5).

6. Plug the power cord into a 115-volt, 60 cycle grounded
outlet.

7. Turn the machine’s motor on by pressing the rocker
switch which is located on the head assembly.

3

MAINTENANCE

Good maintenance procedures assure better operation, fewer
repairs and longer life to your machine.

DISCONNECT THE ELECTRICAL PLUG OF THE
MACHINE FROM THE ELECTRICAL OUTLET
BEFORE DOING ANY CLEANUP, REPAIRS OR
MAINTENANCE OF THE MACHINE AND WHEN
LEAVING THE MACHINE UNATTENDED.

CLEAN THE MACHINE AFTER EACH USE:

1. Wipe the outside with a clean cloth.

2. Clean the collector tank: Release the clamps on each
side of the tank and head assembly. Lift the head as­sembly off and set aside. Lift the filter assembly out of
the collector tank and set aside. Then wipe the inside
of the collector tank with a clean cloth.

3. Empty and check the filter assembly: Empty the re­covered soilage into a suitable container and shake to
remove clinging dirt. Brush the outside of the filter bag
to remove embedded dirt. Check the filter assembly for
tears or holes; repair or replace if necessary. Install the
clean filter assembly into the clean collector tank.

ELECTRICAL CABLE:

Check the cord for any nicks, cuts or damage. Report
these to your supervisor for correction.

VACUUM HEAD ASSEMBLY:

1. Gaskets: Clean the vacuum head gasket and the float
shut-off gasket.

2. Float Shut-Off Device: This should move freely. Re­move any debris or strings from the float cage.

3. Head Assembly: Replace and leave ajar if the collector
tank is damp to prevent mildew.

WHEELS AND CASTERS:

Check these for cuts and nicks. Remove any strings or
debris that may restrict the free movement of the wheels.
Wipe the treads clean.

CARBON BRUSH INSPECTION:

Check for wear at six month intervals or every 600 hours
of operation. The carbon brushes must be replaced if worn
shorter than 3/8 inch.

4

TOOL KIT

PART #54157 (608809)

1

9

21

2

8

20

22

3

23

17

18

4

5

19

7 - 16” Bristle Floor

6

Tool Accessory

9

8

12

8

10

15

16

14

24

11

23

ITEM PART NO. DESCRIPTION QTY.

23

1 600206 Adaptor, 1-1/2 Hose, Vac End 1

2 604108 Hose, 1-1/2x10ft. (w/out adaptors) 1

604114 Hose Asm,1-1/2x10ft.(w/adaptors) 1

3 600205 Adaptor, 1-1/2 Hose, Wand End 1

4 609810 Wand Asm., with Tool Adaptor 1

5 606710 Disconnect Pin Assembly 1

6 600204 Adaptor, Wand 1

7 608810 16” Bristle Floor Tool Asm. 1

8 601803 Top Casting with Adaptor 1

9 601804 Base Casting, Bristle Tool 1

10 600901 Brush, Bristle Tool 1

11 602011 Clamp, Brush 2

12 600701 Blade, Squeegee Pickup 4

14 607212 Retainer 2

15 601802 Base Casting-Squeegee Tool 1

16 608812 16” Squeegee Floor Tool Asm. 1

17 608816 1-1/2” Crevice Tool 1

18 608820 3” Round Dusting Tool 1

19 600210 Tool Adaptor, 1-1/4 to 1-1/2 1

20 608811 16” Carpet Tool Asm. 1

21 607901 Carpet Shoe 1

22 600902 Brush Strip 1

23 964022 Screw 6

24 10-24x3/8 Self-Tapping Screw 5

TOOL KIT ASSEMBLY:

1. Connect the hose to the collector tank by inserting the large,
grooved hose adapter end into the tank adapter. Press the
pawl on Wet/Dry Vacuum to allow the hose adapter to slide
further in. Release the pawl to engage the large groove.

2. Insert the upper wand half firmly into the lower wand assem­bly. The dimple on the lower wand aligns with the groove
of the upper half to assure a rigid fit.

3. Insert the wand end into the free end of the vacuum hose.
Then fasten the proper floor tool to the to the wand by insert­ing the mating end of the floor tool into the adapter collar of
the wand assembly. Pull the tool locking pin to allow total
engagement of the adapter and tool. Release the pin to lock
the tool to the wand.

4. The hand tools may also be used by inserting their adapter
directly into the free end of the vacuum hose.

5. Tool Selection: Choosing the proper tool will give the best
results. To vacuum dust and debris from floors or walls-select
the bristle floor tool. To remove water, liquid waste, strip
solution, etc. from hard surfaced floors-use the squeegee floor
tool. When vacuuming carpets or rugs-choose the carpet
tool.

5

Not included with machine.

SV-12

6

SV-12 PARTS LIST

ITEM PART NO. DESCRIPTION QTY.

1 601540 Cover 1

2 602340 Cap, Motor 1

3 964020 Screw 8

4 608010 Switch 1

5 608511 Strain Relief 1

6 908020 Cord Assembly 1

7 602009 Clamp, Cord 1

8 964165 Screw 2

9 964025 Screw 4

10 600214 Adaptor 1

11 603414 Gasket 1

12 605210 Motor - Vacuum, 115V 1

605211 Motor - Vacuum, 230V 1

600903 Brush, Carbon for 605210 & 605211 (2 req’d/mtr) 2

13 603410 Gasket 1

14 600215 Adaptor, Lower Motor 1

15 603442 Gasket, Dome 1

16 603412 Gasket, Float 1

17 603312 Float 1

18 602413 Cage 1

19 964139 Screw 1

20 920628 Nut 1

23 608617 Tank, Vacuum 1

24 608303 Spring 1

25 603415 Gasket, Coupler 1

26 602409 Coupler 1

27 607001 Pawl 1

28 964143 Screw 2

29 602010 Clamp 2

30 930011 Rivet 4

31 603910 Handle 2

32 600530 Filter Bag Assembly 1

34 964026 Screw 4

35 601308 Base Carriage 1

36 603908 Handle, Transport 1

37 925005 Pin, Dowel 4

38 609713 Wheel 2

39 600216 Adaptor 1

40 601508 Cap, Wheel Shaft 2

41 600218 Adaptor, Lower Motor 1

42 605004 Knob 1

43 609714 Caster 2

44 600804 Bracket 1

45 600807 Bracket, Antistatic 1

51 911267 Terminal Board 1

53 604801 Insulation, Sound 1

55 608101 Sleeve, Motor Cooling Air 1

SSS WET/DRY VACUUM, MODEL SV-12

LIMITED WARRANTY

The SSS Wet/Dry Vacuum, Model SV-12 has been manufactured, tested and inspected in accordance with specific engineering requirements,
and is WARRANTED by the manufacturer to be free from defects in workmanship and materials.

This warranty is, however, subject to the following qualifications, conditions and limitations which are set forth to provide you and all users
of the SSS Wet/Dry Vacuum, Model SV-12 with information concerning the duration, extent, availability and applicability of this Limited

Warranty, the procedure to be taken to obtain its performance and other information concerning the manufacturer’s warranty policy.

1. TO WHOM EXTENDED AND DURATION OF ITEMS COVERED

This warranty extends to the original consumer purchaser from the date it
was purchased and for the items and periods as follows:

Five (5) years parts, one (1) year labor - Stainless Tank

One (1) year parts & labor - All other components unless excluded below.

2. PARTS NOT COVERED BY WARRANTY

Certain parts of the SSS Wet/Dry Vacuum require replacement in the or­dinary course of use due to normal wear by reason of their characteristics.
This warranty does not cover wear parts and accessories of the machine
such as electrical cords, carbon motor brushes, floor brushes, hoses, tools,
filters, casters, wheels, etc.

3. EXCEPTIONS AND EXCLUSIONS FROM WARRANTY

The SSS Wet/Dry Vacuum is required to be used on electric current as
indicated on the nameplate. Otherwise damage, defects, malfunctions or
other failures of the SSS Wet/Dry Vacuum arising from use on electric
current not as indicated are excepted and excluded from this warranty.

Defects, malfunctions, failure or damage of the SSS Wet/Dry Vacuum
caused by improper, unreasonable or negligent use or abuse while in the
possession of the consumer are likewise excluded from this warranty.

If repair is done on your SSS Wet/Dry Vacuum by anyone other than those
below designated as authorized to perform such work without first having
obtained factory instructions, the manufacturer, at its sole option, may
determine that this warranty will not apply and that reimbursement for
such repair will not be made because of the failure to comply with such
factory specified instructions.

If you are unable to locate the Dealer, you may write or otherwise com­municate with Triple S, 2 Executive Park Drive, Billerica, MA 01862
for instructions before repair service is performed by anyone else. In such
event Triple S will provide either the location of a closely available Triple
S Distributor Service Department or other factory instructions.

Upon compliance with the above procedure, all warranted defects will
be repaired, at no additional charge or costs to the consumer, and the
repaired product returned to the consumer, with all shipping and delivery
charges prepaid.

In following the procedures above set forth PLEASE MAKE CERTAIN
to state the Triple S model, type and serial number as shown on the name
plate of the SSS Wet/Dry Vacuum.

REPLACEMENT

In the event of the defect, malfunction or failure of your SSS Wet/Dry
Vacuum or any warranted part to conform with this warranty, the manu­facturer may at its sole option and own expense, replace the SSS Wet/Dry
Vacuum or any warranted part with another new identical or reasonably
equivalent model or part in lieu of repairing the defect.

5. NO REFUND OF PURCHASE PRICE

Triple S will not, as a matter of its warranty policy, refund the consum­er’s purchase price.

6. WARRANTY REGISTRATION CARD FOR YOUR SSS WET/

DRY VACUUM AND REQUESTS FOR INFORMATION

Please fill out the warranty registration card accompanying your SSS
Wet/Dry Vacuum, giving complete information as requested on the card,
and return to Triple S.

4. PROCEDURE TO BE TAKEN TO OBTAIN PERFORMANCE
OF WARRANTY

To secure repair of the SSS Wet/Dry Vacuum or any warranted parts under
this warranty, the following procedure should be taken: The inoperative SSS
Wet/Dry Vacuum or warranted parts, together with satisfactory evidence
of the purchase date, must be delivered with shipping and delivery charges
prepaid to the Dealer from whom purchased.

8/04 605606

This warranty is in lieu of all other expressed or implied warranties.