Trionic Veloped 12er M, Veloped 12er L, Veloped 14er L, Veloped 14er M User Manual

User Manual
English
User Manual
Dear user,
ank you for choosing our product! We truly hope you will experience many pleasant moments and enjoy your Trionic Veloped both o-road and in the city.
Please read the User Manual carefully before use and follow all the guidelines, especially the Safety Instructions.
e Veloped is primarily made for outdoor use.
Trionic Veloped
e Veloped has a unique 3-wheel design, but as you can see it has in fact four wheels. It’s aimed to be used as a walking aid, especially for people with the desire to be physically active out­doors. Developed with a focus on walking and facilitating access for the user, the Veloped is one of a kind. Its main characteristic is a dual front wheel with the capacity to overcome obstacles up to 13 cm high. e force required to overcome a smaller obstacle is also greatly reduced, when compared to a traditional wheel. e 3-wheel design, coupled with the front wheel’s suspension and the air-lled tires, increases both comfort and accessibility on all uneven surfaces.
e Veloped is tested and approved according to the internatio­nal standard ISO-11199-2:2005, for a maximum user weight of 150 kg.
The Product
Technical Data
12er M 12er L 14er M 14er L
Min. height: 75 cm 82 cm 77 cm 84 cm
Max. height: 95 cm 102 cm 97 cm 104 cm
Width: 76 cm 79 cm 76 cm 79 cm
Length: 102 cm 102 cm 107 cm 107 cm
Seat height: 58 cm 63 cm 60 cm 65 cm
Seat width: 44 cm 44 cm 44 cm 44 cm
Wheel size: 12”/31 cm 12”/31 cm 14”/36 cm 14”/36cm
Size folded: L106xW42xH75 cm L106xW42xH82 cm L111xW42xH77 cm L111xW42xH84 cm
Size folded w/o wheels: L84xW42xH59 cm L84xW42xH68 cm L84xW42xH59 cm L84xW42xH68 cm
Weight (w/o bags): 12,3 kg 13,0 kg 12,8 kg 13,5 kg
Weight w/o wheels: 7,2 kg 7,9 kg 7,2 kg 7,9 kg
Max. user weight: 150 kg 150 kg 150 kg 150 kg
Safety
Both brakes should be locked in par­king mode before you use the seat.
Before you start walking with the Velo­ped, make sure it’s completely unfolded.
Be extra careful in steep terrain and on slanting ground.
e stability of the Veloped is tested with a basket load of 5 kg. If you load additional weight to the basket, make sure to distribute the weight evenly in the basket.
Veloped Seat & Basket
Seat cover
e seat cover is made of water-repellent and resistant 600D polyester fabric. It is easily mounted on the seat by the use of push-buttons. Handwash 30°C.
Basket
e basket has a zippered compartment, ideal for keeping valuables such as a wallet, keys or a small handbag. e basket is made of water-repellent and resistant 600D polyester fabric, and it is attached through three velcro sections. In the zip-pocket there’s a small rain cover that you can wrap around the items you carry in the basket. Hand-wash 30°C.
1. Attach the rear wheels to the
frame’s rear axle holes by press­ing the black button in the cen­tre of the wheel and then push­ing the axle all the way into the axle hole. Release the push button.
2. Check that the wheels are properly attached by pulling/ pushing them sideways.
3. Attach the front wheel sus­pension to the front bottom end of the frame in the same manner, i.e. press the black button at the bottom of the
First Time Use
axle and press the axle into the axel hole from underneath. Release the push button.
4. Check that the front wheel is securely fastened by lifting the frame from the surface and pulling the front wheel down­wards.
5. Adjust the height of the han­dlebar as described in Chapter «Gripbar Adjustment».
1. Unfold the Veloped by pull-
ing the gripbar handles side­ways, away from each other.
Walking Mode
2. Check that the Veloped locks in walking mode; when unfolding it make sure you hear a click from the telescopic stay locking into position.
3. e seat can be slid forward and rearward. Push it forward to obtain maximum walking space.
Before using the seat, reaching the basket or folding the Vel­oped, pull the seat rearwards.
Folding the Veloped
1. Pull the seat to the rear.
2. Press the button on the right
of the telescopic stay.
3. Simultaneously lift and fold one frame half against the other.
4. Press the other button on the left of the telescopic stay.
5. Simultaneously lift and fold one frame half against the other in order to fully fold the Veloped together.
To operate the motion brake, pull the brake lever upwards. Brake with both levers at the same time.
You can engage the parking brake in 3 dierent ways.
Option 1: Push the lower red parking trigger downwards with your index nger, while you pull the brake lever at the same time. Make sure that the parking brake is engaged, and that the Veloped does not move.
Motion Brake Parking Brake
Option 2: Pull the upper red par­king trigger rearwards with your thumb, while you pull the brake lever at the same time. Make sure that the parking brake is engaged.
Option 3: Use both hands. Pull the upper red parking trigger rearwards with one hand, while you pull the brake lever with your other hand. Make sure that the parking brake is engaged.
To release the parking brake, brake in the same manner as for using the motion brake.
1. Release both quick-release
levers by folding them out­wards.
2. Adjust the gripbar to
required height, the most ade­quate being the distance from the wrist to the ground when standing with the arms hang­ing freely. Use help to measure!
NOTE: e easiest way to adjust the gripbar is when sit­ting on the seat; this way you can see the height indication marks clearly, thus simplifying height adjustment.
Gripbar Adjustment
3. Lock both quick-release levers by folding them inwards.
NOTE! Do not operate the quick-release levers like wing nuts or screws. e quick­release levers can be replaced with screws and nuts if there is a risk that the user accidentally releases the levers while using the Ve lo p e d.
e angle of the grips can be adjusted so that you get a com­fortable hand position and an optimal support.
1. Loosen the screw on the rear
end of the grip with a 4 mm allen key.
2. Turn/rotate the grip to your chosen angle.
3. Tighten the screw on the rear end of the grip with a 4 mm allen key.
Grip Angle Adjustment
Installing the Rear Wheels
e rear wheels are removable to simplify transportation of the Ve lo p e d.
1. To remove the wheel, press the black button at the centre of the wheel and pull the wheel o.
2. To attach the wheel, press
the black button at the cen­tre of the wheel and push the wheel axle into the axle hole. Release the button when the wheel is in its end position.
3. Hold the tire and push/pull the wheel back and forth lat­erally to check if the wheel is properly secured.
1. If the brakes works poorly,
loosen the adjustment screw on each brake lever (counter­clockwise) and lock it in posi­tion by screwing the lock-nut towards the handle (clock­wise).
Contact your retailer, or the person responsible for servic­ing your Trionic Veloped, if the brakes still works poorly.
Brake Adjustment
e front wheel suspension is removable to simplify trans­portation of the Veloped.
1. Press the black button under
the front hinge to release the front wheel suspension.
2. To remove the entire wheel suspension, lift the frames front end from the surface while pulling the wheel sus­pension downwards.
3. To install the front wheel suspension, lift the front end of the frame, press the black
button and push the wheel axle into the axle hole placed under the frame. Release the black push button. Check that the front wheel suspension is secured by lifting the front end of the frame from the ground and then pulling the wheel sus­pension downwards.
Removing/Installing the Front Wheel
Air Pressure
Check the tire air pressure reg­ularly. Trionic recommends a
1.5 – 2.0 bar tire pressure.
Maximum tire air pressure is
2.5 bar/35 psi.
ere is an adjustment handle on the front wheel, placed in the between the wheels, that can be shifted between two settings.
Lower position:
Oers easy turning with retained climbing capacity.
Upper position:
Oers increased climb­ing capacity, suspension on uneven surfaces and a higher directional stability.
Turn the front wheel 180 degrees for easier access to the adjustment handle.
1. Grab the left wheel with your left hand and lift the Vel­oped front end slightly o the ground.
2. While holding the Veloped lifted with your left hand, grab the black knob with the green dot with your right hand, and pull it outwards (towards you).
Change Front Wheel Setting: City mode/Off-road mode
3. Slide the adjustor (right hand) either downwards or upwards. It is important that you slide the adjustor to its very bottom or upper end posi­tion.
4. Release the black knob and it will spring back and lock the front wheel to your chosen set­ting.
e basket of the Trionic Veloped has a 22-litre load­ing capacity. It has a small zippered pocket at the rear end for valuables and smaller objects. e Veloped basket is removable, and is attached to the frame basket rails with three velcro sections.
1. Wrap the rear velcro aps around the rails from under­neath, between the frame and the basket rail. Fold them inwards and x the velcro sec­tions on the inner of the basket lining.
2. Attach the front velcro ap in the same manner.
Removing/Attaching the Basket
3. If necessary, adjust the velcro sections to ensure that the basket is properly fastened.
NOTE! Make sure to insert the plastic plate into the bot­tom sleeve of the basket before attaching the basket to the frame.
e Veloped’s sliding seat is comprised of a seat base and a removable cover xed with nine push buttons.
1. Hold the seat cover with the text Trionic to the right. Wrap the long ap between the teles­copic stay and the seat base.
2. Attach the three front push buttons of the long ap to the seat base.
3. Press the three push buttons on the short ap onto the seat base.
Removing/Installing the Seat
4. Finally, press the three last push buttons of the long ap onto the short ap.
Safety Instructions
Before use, check that your Trionic Veloped functions properly:
• Check the function of the motion and parking brakes.
• Make sure that the frame is locked in unfolded walking mode.
• Check that the gripbar is properly secured at the correct
height.
• Avoid contact with the front end when unfolding the frame
as there is a risk of pinching.
• e user’s weight may not exceed 150 kg.
• Do not use the Trionic Veloped as a wheel chair or for trans-
porting people.
• e Veloped is aimed to be used as a walking aid, mainly for
outdoor use.
• An annual control of the product is recommended to ensure
its function, either by your dealer or service representative authorized by Trionic.
• Do not use a defect Veloped.
Service Instructions
In order to maintain function and safety, make sure the following is carried out regularly:
• Clean the Veloped with normal dish washing liquid, water and a dishcloth. Make sure it’s properly dried.
• Keep the wheels clean with dish washing liquid, water and a plastic brush.
• Check that screws and levers are tightened properly.
• If your Veloped is not in perfect condition: please immedia­tely contact your retailer/dealer or service representative authorized to service your Trionic Veloped.
Trionic does not take responsibility for any alterations (adjust­ments or inadequate repairs) done to the product without prior authorization.
Seminariegatan 29 C
SE-752 28 Uppsala, SWEDEN
www.trionic.se, info@trionic.se
Tel.: +46 8 522 100 50, Fax.: 08-522 100 59
MAX
SN: 201202-000138
ART no: 11-00-011
Max Weight: 150 kg Width: 76 cm Length: 102 cm Height: 75-94 cm 2010-02
Primarily for outdoor use
ISO 11199.2:2005
S
Guarantee
e Trionic Veloped includes a 10-year guarantee, excluding parts that are subject to normal wear (tires, tubes, brake pads, brake cables, brake cable housings, grips and textile parts). e guarantee is valid from the date of purchase, and covers Trionic original parts only.
___________________________________________________________ Serial Number
___________________________________________________________ Date/Stamp/Signature
CE - Trionic Sverige AB ensures that the above mentioned pro­duct meets the relevant legislation requirements (1993:584) con­cerning medical products as well as the specications contained in the provisions for medical products (LVFS 2003:11). e pro­duct meets the specications in EC’s directive regarding medi­cal technical products 93/42/EEC.
Label
e Veloped is tested and approved accor­ding to the provisions in the international standard for walking aid products: ISO 11199-2:2005 «Walking aids manipulated with both arms».
e user’s weight may not exceed 150kg.
Manufacturing Date
Serial Number
Read the manual
before use
According to ISO
standard it is primarily
for outdoor use.
Max. and Min.
Height
Width
Max. User Weight
Manufacturer
Article Number
Aid approved according to
93/42/EEC
Product Code: EAN 13
Length
Troubleshooting
If your Trionic Veloped does not work satisfactory, you can check it by following the troubleshooting guide below. If the guide does not help you solve the problem, please contact your retailer, service provider, distributor or Trionic Sverige AB.
Environmentally Friendly
e Trionic Veloped is manufactured in the way to have as little negative impact on the environment as possible during its lifecy­cle. When the product has served its purpose it can be scrapped and the parts can be recycled.
e product’s aluminium components are separated from the remaining parts when sorted for recycling. e parts are sorted into metal, plastic and mixed materials.
e greater part of the product is made of aluminium, steel and plastic.
Examples of components made of mixed materials are the brake levers, wheels and gripbar.
If you are uncertain of how to handle the recyclable mate­rial, please contact your local authorities, as dierent muni­cipalities/recycling companies follow dierent recycling methods.
Trionic Sverige AB is a member of REPA, PRO Europe (Die Grüne punkt) and fully implements the European Directive on Packaging and Packaging Waste dated December 20, 1994.
Problem: The seat is sagging/too low. Possible cause: The rear velcro band under
the seat base needs to be tightened, or the Veloped is not correctly unfolded. Action: Remove the seat cover and tighten the rear velcro band of the seat base, with the Veloped fully unfolded. Do not tighten the Velcro band too much since it may turn the sliding of the seat back and forth more difcult.
Problem: Difcult steering. Possible cause: The front wheel is adjusted
for irregular terrain/upper position. Action: Change the setting of the front wheel suspension to the easy turning mode/ lower position, as described in the chapter
«Change the Front Wheel Setting».
Problem: Poor brake function. Possible cause: The brake hub or brake band
is worn out, or the cable is not tight enough. Action: Adjust the brake cable tension as described in the chapter «Brake Adjustment».
Problem: The rear or front wheels are not secured. Possible cause: The wheel has not been cor­rectly attached. Action: Check that the push button of the axle locks correctly. Please contact your service provider if the wheel does not lock correctly in position.
Trionic Sverige AB
Seminariegatan 29 C
SE-752 28 Uppsala
SWEDEN
www.trionic.biz
info@trionic.se
Telephone: +46 8 522 100 50
Fax: +46 8 522 100 59
Corp.ID: 556698-1527. VAT Reg. No SE556698152701
Loading...