Page 1
Evaluation Board for 3-Phase BLDC/PMSM
EVALUATION BOARD
TMC6100-EVAL Evaluation Kit
Document Revision V1.00 • 2019-Dec-20
The TMC6100-EVAL is designed for evaluating all features of the TMC6100. The evaluation board
is part of TRINAMICs user-friendly plug-in system for chip evaluation. Just connect the TMC6100EVAL with Landungsbruecke, the associated base board. Therefore, use the dedicated connector
board, called Eselsbruecke. Eselsbruecke offers test points for every connector pin.
Features
•
3-phase BLDC/PMSM motor with
up to 10A coil current
•
Gate Drive Programmable 0.5A/1A/1.5A
• Supply Voltage 12. . . 48V (55V max)
•
SPI Interface for diagnostics / con-
figuration
•
Optional BBM logic for single line
control
•
Programmable Control Interface with
3 or 6 line drive
•
Full Protection & programmable Diagnostics
Applications
• Onboard Current Shunt Amplifiers
• PMSM FOC drives
• BLDC motors
• Robotics
Simplified Block Diagram
• CNC Machines
• Industrial Drives
• LEV
• Factory Automation
• Blowers
• Pumps
©2019 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany
Terms of delivery and rights to technical change reserved.
Download newest version at: www.trinamic.com
Read entire documentation.
Page 2
TMC6100-EVAL Evaluation Kit • Document Revision V1.00 • 2019-Dec-20
2 / 6
Contents
1 Getting Started 3
1.1 First Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Hardware Information 5
3 Revision History 6
3.1 Document Revision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
©2019 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany
Terms of delivery and rights to technical change reserved.
Download newest version at www.trinamic.com
Page 3
TMC6100-EVAL Evaluation Kit • Document Revision V1.00 • 2019-Dec-20
1 Getting Started
3 / 6
You need
• TMC6100-EVAL
•
Landungsbruecke or Startrampe with latest
firmware. We recommend the Landungs-
bruecke as it offers faster USB communication.
•
Latest TMCL-IDE (please download from
www.trinamic.com) and PC
• 1x Eselsbruecke adapter board
• TMC4671-EVAL (Hardware FOC Controller)
• BLDC motor
• USB interface
• Power Supply
• Cables for interface, motors and power
Precautions
•
Do not mix up connections or short-circuit pins.
• Avoid bounding I/O wires with motor wires.
•
Do not exceed the maximum rated supply supply voltage!
•
Do not connect or disconnect the motor while
powered!
•
Please check schematics for Jumper settings
and input/output connector description.
• START WITH POWER SUPPLY OFF!
Figure 1: TMC6100-EVAL -Kit view
NOTICE
©2019 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany
Terms of delivery and rights to technical change reserved.
Download newest version at www.trinamic.com
The Landungsbruecke operates on USB Power Supply. All other voltages are
generated from +VM. Kit works only, when +VM is applied.
Page 4
TMC6100-EVAL Evaluation Kit • Document Revision V1.00 • 2019-Dec-20
1.1 First Start-Up
1.
Make sure that the latest version of the TMCL-IDE is installed. The TMCL-IDE can be downloaded
from www.trinamic.com/support/software/tmcl-ide/.
2. Open the TMCL-IDE and connect the Landungsbruecke or Startrampe via USB to the computer. For
Windows 8 and higher is no driver needed, on Windows 7 machines the TMCL-IDE is installing the
driver automatically.
3.
Verify that the Landungsbruecke or Startrampe is using the latest firmware version. The firmware
version is shown in the connected device tree.
4 / 6
Figure 2: Firmware Version
4.
The TMCL-IDE 3.0 needs room to show all important information and to provide a good overview.
Therefore, arrange the main window related to your needs. We recommend using full screen. For
evaluation boards it is essential to have access to the registers. Therefore open up the Register
Browser (left side). For a better view click top right on the normal icon to get a maximized register
browser window.
5.
Figure 3: Landungsbruecke Dialogue
©2019 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany
Terms of delivery and rights to technical change reserved.
Download newest version at www.trinamic.com
Page 5
TMC6100-EVAL Evaluation Kit • Document Revision V1.00 • 2019-Dec-20
6. There is 1 solder option on the TMC6100-EVAL as highlighted in red in the image below.
It allows for changing the VCCIO between 3.3V and 5V.Resistor R402 (0Ω) selects VCCIO = 3.3V and is
assembled by default. R401 is not assembled in this case.If R401 (0Ω) is assembled instead of R402,
then VCCIO = 5V.
5 / 6
Figure 4: Solder jumper on the TMC6100-EVAL
2 Hardware Information
All design files for our evaluation boards are available for free. The TMC6100-EVAL has been done with
KiCAD. We offer the original ECAD files, Gerber data, the BOM, and PDF copies.
The files can be downloaded from the evaluation boards’ website directly at
support/eval-kits/.
Note
If files are missing on the website or something is wrong please send us a note.
https://www.trinamic.com/
©2019 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany
Terms of delivery and rights to technical change reserved.
Download newest version at www.trinamic.com
Page 6
TMC6100-EVAL Evaluation Kit • Document Revision V1.00 • 2019-Dec-20
3 Revision History
3.1 Document Revision
Version Date Author Description
1.00 2019-12-20 SK Initial release.
Table 1: Document Revision
6 / 6
©2019 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany
Terms of delivery and rights to technical change reserved.
Download newest version at www.trinamic.com
Loading...