Trilithic RP1103N User Manual
Redpine Signals, Inc. Proprietary and Confidential
03 Evaluation Board
User Guide
Version 1.5
2011
Redpine Signals, Inc
.
2107 N. First Street, #680
San Jose, CA 95131.
3385
2019
RS9110-N-11-
Ver sion 1.5
August
Tel: (408) 748-
Fax: (408) 705-
Email: info@redpinesignals.com
Website: www.redpinesignals.com
Redpine Signals, Inc. Proprietary and Confidential
Page 2
03 Evaluation Board
R
User Guide
Version 1.5
Disclaimer
d to Redpine
Signals Inc. products. This information is provided as a service to our
customers, and may be used for information purposes only.
Redpine assumes no liabilities or responsibilities for errors or omissions in this
ay be changed at any time at Redpine’s sole
discretion without any prior notice to anyone. Redpine is not committed to
pdating these documents in the future.
Copyright © 2011 Redpine Signals, Inc. All rights reserved.
The information in this document pertains to information relate
document. This document m
u
S91 1 0 -N-1 1 -0 3 Eval u ati on B o ard
RS9110-N-11-
Us e r Gu i d e
Ver s i o n 1.5
Redpine Signals, Inc. Proprietary and Confidential
Page 3
03 Evaluation Board
R
User Guide
Version 1.5
Table
of
Contents
.
1: Test Setup.............................................................................6
.2: Evaluation Software
– Windows
XP.............................
..........7
.3: Evaluation Process on Windows X
P..............................
.........8
.4: Evalua
tion Software
– Linux.........
...............................
..........8
.5: Evaluation Process on Linux.........
...............................
..........9
.6: Evaluation Software
– Windows C
E..............................
.........9
.7: Evaluation Process
on Windows CE......................................10
3.1: SPI/SDIO connector............................................................11
3.2: GPIO Interface Header Details.............................................11
3.3: SD Memory Interface...........................................................1
2
S91 1 0 -N-1 1 -0 3 Eval u ati on B o ard
RS9110-N-11-
Us e r Gu i d e
Ver s i o n 1.5
1: Introduction.......................................................................5
: Wi-Fi Data Transfer Tests...................................................6
3: Connector Details.............................................................11
4: Compliance Statements....................................................12
Redpine Signals, Inc. Proprietary and Confidential
Page 4
03 Evaluation Board
R
User Guide
Version 1.5
Table
of
Figures
Figure 1: RS9110-N-11-03 Evaluation Board and Connectors.........................5
Figure 2: RF Cable Connected to the RS9110-N-11-03 Evaluation Board........6
Figure 3: Test Setup for Throughput Measurement.........................................7
S91 1 0 -N-1 1 -0 3 Eval u ati on B o ard
RS9110-N-11-
Us e r Gu i d e
Ver s i o n 1.5
Redpine Signals, Inc. Proprietary and Confidential
Page 5
03 Evaluation Board
R
User Guide
Version 1.5
1: Introduction
03 evaluation board provides a complete IEEE 802.11abgn
03
02.11abgn WLAN module mounted on it along with few other supporting
components such as 40 MHz reference oscillator and other passives. The
power WLAN module.
The board connects to a host processor through SDIO or SPI interfaces. It
also provides the connectivity for the WLAN module to the Vector Signal
Generator (VSG) and Vector Signal Analyzer (VSA) through a microwave
ector switch.
03 evaluation board facilitates you in carrying out following
tests.
valuation of the Transmit and Receive performance of the radio
end throughput performance
03
evaluation board
The RS9110-N-11W ireless LAN evaluation platform. This basically has the RS9110-N-11-
IEEE 8
RS9110-N-11-03 is a high-performance, low-
coaxial conn
The RS9110-N-11-
S91 1 0 -N-1 1 -0 3 Eval u ati on B o ard
RS9110-N-11-
Us e r Gu i d e
Ver s i o n 1.5
E
Evaluation of the end–to-
The following picture illustrates various connectors on the RS9110-N-11-
Figure 1: RS9110-N-11-03 Evaluation Board and Connectors
Loading...