TIGER Main Board
[ Back to Previous ]
TIGER Jumper Settings
Jumper and DIP switch settings
- PENTIUM 60MHz or 66MHz microprocessor (depending on model type)
DIP SW setting function _
One
ON When using a password
OFF When not using a password
2
ON When using a color video board
OFF When using a mono video board
4
ON VESA Local 1 Wait State
OFF VESA Local 0 Wait State
5
ON Over Local BUS SPEED 33MHz
OFF Local BUS SPEED less than 33MHz
* Set No. 6 and 7 of SW1 to OFF.
SW1&JP 128KB 512 KB
3 ON OFF
JP4,JP5 IN OUT
TIGER MEMORY SETUP
Cache memory capacity setting (128 KB or 512 KB, depending on model)
main memory
type
72-pin SIMM module
Single Density SIMM: 1MB, 4MB, 16MB
Double Density SIMM: 2MB, 8MB, 32MB
speed 70ns
Volume Available in 1MB, 2MB, 4MB, 8MB,16MB, 32MB
expansion Up to 128MB (default 8MB built into motherboard)
How to install
memory size
bank 0 bank 1
(SIMM1) (SIMM2) (SIMM3) (SIMM4)
2m 1M 1M -- --
4M 2m 2m -- --
1M 1M 1M 1M
6M 1M 1M 2m 2m
8m 4M 4M -- --
2m 2m 2m 2m
10M 1M 1M 4M 4M
12M 2m 2m 4M 4M
16M 8m 8m -- --
4M 4M 4M 4M
18M 1M 1M 8m 8m
20M 2m 2m 8m 8m
24M 4M 4M 8m 8m
32m 8m 8m 8m 8m
16M 16M -- --
34m 1M 1M 16M 16M
36m 2m 2m 16M 16M
40M 4M 4M 16M 16M
48M 8m 8m 16M 16M
64M 16M 16M 16M 16M
32m 32m -- --
66m 1M 1M 32m 32m
68M 2m 2m 32m 32m
72m 4M 4M 32m 32m
80M 8m 8m 32m 32m
96M 16M 16M 32m 32m
128M 32m 32m 32m 32m
TIGER Main B/D CMOS SETUP
use key
Move by each item up, down, left, right arrow keys
Go to setup screen page PaUp or PaDn key (composed of two screens)
select each item
+ or - 키
When booting, press Ctrl + ALT + S KEY
menu item option item
Standard System Parameters (2/1 page)
System Time time setting
System Date set date
Floppy Disk A Not / 360K 5.¼/ 1.2M 5.¼ / 720KB ½ / 1.44M ½ / 2.88M ½
Floppy Disk B Not / 360K 5.¼/ 1.2M 5.¼ / 720KB ½ / 1.44M ½ / 2.88M ½
Hard Disk C Not Install, 1~47(47 Minutes User Define Type)
Hard Disk D Not Install, 1~47(47 Minutes User Define Type)
Video Card EGA/VGA, MONO, CGA 40, CGA 80
Keyboard Installed, Not Installed
CPU Speed Fast, Slow
PS/2 Mouse Installed, Not Installed
Serial Port COM1 + COM2, COM1(3F8), COM2(2F8), Disabled
Parallel Port LPT1(3BC), LPT2(378), LPT278
Base Memory XXX KB
Extended Memory XXXXXX KB
FDD ASSIGN No Changed, Changed --> A: B: changeable without cable change
NumLock ON No, Yes
ON B/D IDE Enabled, Disabled
ON B/D FDC Enabled, Disabled
Parallel Direction Uni-D, Bi-D
OPTI 82C596 / 82C597 Chip Set Feature Control
System BIOS Shadow Enabled, Disabled
Video BIOS Shadow Enabled, Disabled
System BIOS Cache Enabled, Disabled
Video BIOS Cache Enabled, Disabled
Password Not Installed
a. Disabled password
b. Enabled BOOT password
c. Enabled SETUP password
d. Enabled BOOT/SETUP password
e. Change, Enter new password
Enable BOOT and SETUP password check
Enable SETUP password check
Enable BOOT password check
Loading...