SANJOSE-II Main Board
[ Back to Previous ]
SANJOSE-II Jumper Settings
CPU clock setting
jumper J25 J26 J27 J28 J29 J30
DX/DX2 OPEN OPEN 3-4 1-2,3-4 OPEN OPEN
SX OPEN OPEN OPEN 2-3 OPEN OPEN
P24T 2-3,4-5 1-2 2-3 1-2,3-4 1-2 1-2
CX486S 1-2,3-4 2-3 OPEN 2-3 1-2 2-3
CX486DX2,CX486DX(M7) 1-2,3-4 2-3 3-4 1-2,3-4 1-2 2-3
SL SX 2-3,4-5 OPEN OPEN 2-3 1-2 OPEN
SL DX/DX2,DX4 2-3,4-5 OPEN 3-4 1-2,3-4 1-2 OPEN
J32: 2-3 (initial setting)
P24D: Same as SL DX2, close J36, J37, J38.
AMD DX4 : Same installation as P24D. However, select 3.45V for CPU power.
Set CPU Voltage
JP1
CPU Voltage Selection
+5V(486 Serise)
+3.45V(486DX4-75/100MHz), Cx 486DX2-
(V)50/66MHz), 3.3V(AMD 486DX4-100MHz)
J15, J16 Close Open
J17, J18 Open Close
CPU clock setting
jumper
CPU clock setting (25 MHz) CPU clock setting (33 MHz)
SX/25,DX/25,DX2/50,DX4/75 SX/33,DX/33,DX2/66,DX4/100
J7 1-2 2-3
J8 2-3 1-2
J9 1-2 1-2
CPU vendor settings
jumper Intel/AMD Cyrix
J22 1-2 2-3
J24 1-2 1-2
set password
JP14 Password Selection
2-3 Enabled
1-2 Disabled
ECP Mode DMA setting
jumper DRQ1 & DAK #1 DRQ3 & DAK #3
J39 1-2 2-3
J40 1-2 2-3
cache memory settings
type: 28-pin DIP type (processed as a socket)
speed: 15ns
expansion: Up to 256 KB
jumper 128KB 256KB
J19 1-2 2-3
J20 1-2 2-3
J21 2-3 1-2
캐시 메모리가 설치되지 않은 경우 J19:1-2, J20 : 1-2, J21 : 2-3으로 설정 바람
SANJOSE-II CPU
CPU clock setting
jumper J25 J26 J27 J28 J29 J30
DX/DX2 OPEN OPEN 3-4 1-2,3-4 OPEN OPEN
SX OPEN OPEN OPEN 2-3 OPEN OPEN
P24T 2-3,4-5 1-2 2-3 1-2,3-4 1-2 1-2
CX486S 1-2,3-4 2-3 OPEN 2-3 1-2 2-3
CX486DX2,CX486DX(M7) 1-2,3-4 2-3 3-4 1-2,3-4 1-2 2-3
SL SX 2-3,4-5 OPEN OPEN 2-3 1-2 OPEN
SL DX/DX2,DX4 2-3,4-5 OPEN 3-4 1-2,3-4 1-2 OPEN
J32: 2-3 (initial setting)
P24D: Same as SL DX2, close J36, J37, J38.
AMD DX4 : Same installation as P24D. However, select 3.45V for CPU power.
Set CPU Voltage
JP1
CPU Voltage Selection
+5V(486 Serise)
+3.45V(486DX4-75/100MHz), Cx 486DX2-
(V)50/66MHz), 3.3V(AMD 486DX4-100MHz)
J15, J16 Close Open
J17, J18 Open Close
CPU clock setting
jumper
CPU clock setting (25 MHz) CPU clock setting (33 MHz)
SX/25,DX/25,DX2/50,DX4/75 SX/33,DX/33,DX2/66,DX4/100
J7 1-2 2-3
J8 2-3 1-2
J9 1-2 1-2
CPU vendor settings
jumper Intel/AMD Cyrix
J22 1-2 2-3
J24 1-2 1-2
SANJOSE-II Memory Settings
cache memory settings
type: 28-pin DIP type (processed as a socket)
speed: 15ns
expansion: Up to 256 KB
main memory
type: 72-pin SIMM module
speed: 70ns
Volume: 1MB, 2MB,4MB,8MB, 16MB, 32MB 64MB available
expansion: up to 256MB
How to install
When installing two memories to [Bank 0 and Bank 1] (or [Bank 2 and Bank 3]), SIMM modules of the same type must be installed.
[Memory capacity] installed in [Group A] must be greater than memory capacity in [Group B].
memory size group A group B
basic memory Bank 0 (SIMM1) Bank 1 (SIMM2) Bank 2 (SIMM3) Bank 3 (SIMM4)
4M
2m 2m -- --
4M -- -- --
8m
4M 4M -- --
8m -- -- --
12M 4M 4M 4M --
16M
4M 4M 4M 4M
16M -- -- --
24M 8m 8m 4M 4M
32m
8m 8m 8m 8m
16M 16M -- --
32m -- -- --
48M
16M 16M 8m 8m
16M 16M 16M --
64M
16M 16M 16M 16M
32m 32m -- --
64M -- -- --
96M 32m 32m 32m --
128M
32m 32m 32m 32m
64M 64M -- --
160M 64M 64M 32m --
192M 64M 64M 64M --
256M 64M 64M 64M 64M
SANNJOSE-II Main B/D CMOS SETUP
Press DELKEY at bootup
Level 1 Step 2 Step 3 selection option
Setup Standard Date/Time
date, time setting
Floppy A
Not / 360K 5.¼/ 1.2M 5.¼ /
Floppy B
720KB ½ / 1.44M ½
Master Disk
Not / 1~45 / User / ESDI / SCSI
Slave Disk
Advanced Quick Boot On On, Off
Typematic Rate (Chars/Sec) 30
System Keyboard Present Absent, Present
Primary display VGA/EGA
PS/2 Mouse Support Enable Disabled, Enabled
System Boot Up NumLock On On, Off
Floppy Drive Swapping Disabled Disabled, Enabled
System Boot Up Sequence A:, C: A:, C:C:, A:
System Boot CPU Speed High
External Cache Enabled Enabled, disabled
Internal Cache Enabled Enabled, disabled
Password Checking Setup Setup, Always
Video Shadow C000, 32K Enabled Enabled, disabled
Shadow(C800,CC00,D000,D800,DC00), 16K
Adv HDD IDE Pri. Master HDD Block xfer Enabled Disabled, Enabled
IDE Pri. Master HDD LBA Mode Enabled Disabled, Enabled
IDE Pri. Master HDD 32bit xfer Enabled Disabled, Enabled
IDE Pri. Slave HDD Block xfer Enabled Disabled, Enabled
IDE Pri. Slave HDD LBA Mode Enabled Disabled, Enabled
IDE Pri. Slave HDD 32bit xfer Enabled Disabled, Enabled
Number of HDDs in 2nd Connector None None/HDD(+CD)/IDE CD/2HDDs
IDE Sec. Master HDD Block xfer Enabled Disabled, Enabled
IDE Sec. Master HDD LBA Mode Enabled Disabled, Enabled
IDE Sec. Master HDD 32bit xfer Enabled Disabled, Enabled
IDE Sec. Slave HDD Block xfer Enabled Disabled, Enabled
IDE Sec. Slave HDD LBA Mode Enabled Disabled, Enabled
IDE Sec. Slave HDD 32bit xfer Enabled Disabled, Enabled
Power Mgmt Power Management Mode Select Enabled Disabled, Enabled
Doze Mode Timeout 2 min 15sec ~ 512Min
Sleep Mode Timeout 8 Min Disabled, 2Min ~ 512Min
Suspend Mode Timeout 32 min Disabled, 2Min ~ 512Min
Monitor VGA Activity Disabled Disabled, Enabled
IDE Drive Power Down Enabled Enabled, Disabled
Peripheral OnBoard FDC Enabled Disabled, Enabled
OnBoard PCI IDE Enabled Disabled, Enabled
Serial Port 1 3F8H Disabled, 3F8H
Serial Port 2 2F8H Disabled, 2F8H
Parallel Port 378H Disabled, 378H, 278H
Parallel Port Mode Normal Normal, Bi-Dir, EPP, ECP
Internal Speaker Sound Enabled Enabled, Disabled
Utility DetectMaster Automatically reduces the capacity of the hard disk drive connected to the Primary IDE connector.
DetectSlave
Supported (hardware connected to the Secondary IDE connector is automatically recognized without
setting)
Color Set Set-up screen color selection
Security Password Up to 6 digits can be entered
Anti-Virus Prevent virus infection or other data access from being 'Write' to the boot sector.
Default Original Modified to the step immediately before the setup change
Optimal Automatic setting function for optimal environment (Standard, Utility, Password are not changed)
Fail-safe Automatically set the most stable value for users to use the system
Loading...