User
manual
Dishwasher
TDF 221
Content
Safety information - - - - - - - - - - - - - - - - - -3
Control panel and functions - - - - - - - - - - -4
Programme table - - - - - - - - - - - - - - - - - - -6
Before the first use - - - - - - - - - - - - - - - - -7
Setting the water softener - - - - - - - - - - - - -7
Filling with dishwasher salt - - - - - - - - - - -10
Filling with rinse aid - - - - - - - - - - - - - - - -11
Adjusting the dosage of rinse aid - - - - - - -11
Loading cutlery and dishes - - - - - - - - - - -12
Filling with detergent - - - - - - - - - - - - - - -14
Unloading the dishwasher - - - - - - - - - - - -14
Cleaning and care - - - - - - - - - - - - - - - - - 15
Environmental concerns - - - - - - - - - - - - - 16
Something not working- - - - - - - - - - - - - - 17
Technical data- - - - - - - - - - - - - - - - - - - - 19
Consumption values - - - - - - - - - - - - - - - 19
Hints for test institutes - - - - - - - - - - - - - - 20
Installation - - - - - - - - - - - - - - - - - - - - - - 21
Service and spare parts - - - - - - - - - - - - - 24
Guarantee conditions - - - - - - - - - - - - - - - 25
2
Safety information
In the interest of your safety and to ensure the correct use, before installing and first using the
appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary
mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly
familiar with its operation and safety features. Save these instructions and make sure that they
remain with the appliance if it is moved or sold, so that everyone using it through its life will be
properly informed on appliance use and safety.
Correct use
● This dishwasher is only intended for washing
household utensils suitable for machine
washing.
● Do not put any solvents in the dishwasher.
This could cause an explosion.
● Knives and other items with sharp points
must be loaded in the cutlery basket with
their points down or placed in a horizontal
position in the upper basket.
● Only use products (detergent, salt and rinse
aid) suitable for dishwashers.
● Avoid opening the door whilst the appliance
is in operation, hot steam may escape.
● Do not take any dishes out of the dishwasher
before the end of the dishwashing cycle.
● After use, isolate the appliance from the
power supply and turn off the water supply.
● This product should be serviced only by an
authorised service engineer, and only
genuine spare parts should be used.
General safety
● Dishwasher detergents can cause chemical
burns to eyes, mouth and throat. Could
endanger life! Comply with the safety
instructions of the dishwasher detergent
manufacturer.
● The water in your dishwasher is not for
drinking. Detergent residues may still be
present in your machine.
● Ensure that the door of the dishwasher is
always closed when it is not being loaded or
unloaded. In this way you will avoid anybody
tripping over the open door and hurting
themselves.
● Do not sit or stand on the open door.
Child safety
● This appliance is designed to be operated by
adults. Don’t allow children to use the
dishwasher unsupervised.
● Keep all packaging well away from children.
There is risk of suffocation.
● Keep all detergents in a safe place out of
children’s reach.
● Keep children well away from the dishwasher
when the door is open.
Installation
● Check your dishwasher for any transport
damage. Never connect a damaged
machine. If your dishwasher is damaged
contact your supplier.
● All packaging must be removed before use.
● Any electrical and plumbing work required to
install this appliance must be carried out by
a qualified and competent person.
● For safety reasons it is dangerous to alter
the specifications or attempt to modify this
product in any way.
3
● Never use the dishwasher if the electrical
1
2
3
4
5
supply cable and water hoses are damaged;
or if the control panel, work top or plinth area
are damaged such that the inside of the
appliance is freely accessible. Contact your
local Service Force centre, in order to avoid
hazard.
● All sides of the dishwasher must never be
drilled to prevent damage to hydraulic and
electric components.
WARNING!
For electrical and water connection carefully
follow the instructions given in specific
paragraphs.
Control panel and functions
Programme selector dial and On/Off switch
Programme phase indicator lights
Delay start button
Programme guide
Programme selector
dial and On/Off switch
4
Start/Cancel button
Salt and rinse aid refilling lights
● when in this position, the machine is switched off (corresponding light off),
● when the marker on the dial corresponds with a programme, the machine
is switched on and a programme is selected (corresponding light on)
Start / cancel button
Delay start button
● Starting the washing programme:
1. Select a washing programme.
2. Press the start / cancel button (corresponding light on).
IMPORTANT!
Once the programme has started, if you want to change the selection made
you must cancel the washing programme in progress.
● Cancel the washing programme in progress:
1. Press and hold the start / cancel button until the corresponding light
turns off.
2. Release the start / cancel button.
3. Turn the programme selector dial to the Off position or select a new
washing programme (check that there is detergent in the detergent
dispenser.
This option allows the start of the programme to be delayed by 3 hours.
Once the washing programme has been set, press the delay start button.
The corresponding indicator light illuminates.
Press the start / cancel button, the countdown of the delay start begins
automatically.
Once the countdown has elapsed the washing programme will start
automatically. The delay start indicator light turns off.
Cancel the delay start in progress:
press and hold the start / cancel button until the start / cancel and delay start
indicator lights turn off.
To start the washing programme press the start / cancel button.
Wash light
Drying light
End light
Illuminates when the washing and rinsing phases are running.
Illuminates when the drying phase is running.
Illuminates when the washing programme has ended. Switch off the
dishwasher by returning the programme selector dial to the Off position. The
On/Off light turns off.
It also has added functions of visual signalling as:
- the setting of the water softener,
- intervention of an alarm due to the malfunction of the machine.
5
Salt refilling light
Illuminates when special salt needs to be filled.
It can remain illuminated several hours after the salt has been filled.
Rinse aid refilling
Illuminates when rinse aid needs to be filled.
light
Programme table
Programme Use Cycle description
POWER WASH 70° Heavy soil. Prewash - Main wash
NORMAL WASH 65° Normal soil. Prewash - Main wash
1 Crockery, cutlery, 2 intermediate rinses -
pots and pans Final rinse - Dry
2 Crockery and cutlery 2 intermediate rinses -
Final rinse - Dry
QUICK WASH 65° Light soil. Main wash-
ECO WASH 50° Normal soil. Prewash - Main wash
RINSE & HOLD Any. Prewash
3 Crockery and cutlery Final rinse
4 Crockery and cutlery 1 intermediate rinse -
Final rinse - Dry
5 Partial load (to be completed later in the
day). This programme does not require the
use of detergent.
6
Before the first use
When using separate special
(dishwasher) salt, rinse aid and
detergent:
- set the water softener
- add special (dishwasher) salt
- fill up with rinse aid
When using tablets that integrate
rinse aid and detergent:
there is no need to fill up with rinse aid
- set the water softener
- add special (dishwasher) salt
When using tablets that integrate
rinse aid, detergent, salt function
and other additives:
there is no need to fill up with special salt or
rinse aid.
Check whether these detergents are suitable
for your water hardness. Follow the
manufacturers instructions.
- Set the water hardness to level 1.
IMPORTANT!
If the drying results are not satisfactory we
recommend that you:
1. Fill up the rinse aid dispenser with rinse aid.
2. Set the rinse aid dosage to position 2.
If you decide in future to use separated
detergents, we advise that you:
- Fill up the salt and rinse aid container.
- Adjust the water hardness setting to the
highest level and perform 1 normal washing
programme without loading any dishes.
- Adjust the water hardness setting according
to the hardness of the water in your area.
- Adjust the rinse aid dosage
Setting the water softener
The dishwasher is equipped with a water
softener designed to remove minerals and salts
from the water supply, which would have a
detrimental or adverse effect on the operation
of the appliance.
The softener should be adjusted according to
the hardness of the water in your area. Your
local Water Authority can advise you on the
hardness of the water in your area.
IMPORTANT!
The water softener must be set in both ways:
manually and electronically.
7
Water hardness Number of flashes of the Adjustment of the water
“end of programme” light hardness setting
in Clarke
1)
in °TH2)in mmol/l
3)
manually electronically
64 - 88 91 - 125 9,0 - 12,5 10 2 level 10
53 - 63 76 - 90 7,6 - 8,9 9 2 level 9
46 - 52 65 - 75 6,5 - 7,5 8 2 level 8
36 - 45 51 - 64 5,1 - 6,4 7 2 level 7
28 - 35 40 - 50 4,0 - 5,0 6 2 level 6
23 - 27 33 - 39 3,3 - 3,9 5 2 level 5
18 - 22 26 - 32 2,6 - 3,2 4 1 level 4
13 - 17 19 - 25 1,9 - 2,5 3 1 level 3
5 - 12 7 - 18 0,7 - 1,8 2 1 level 2
< 5 < 7 < 0,7 1 1 level 1
no salt necessary
1) Clarke degree, measure of the water hardness.
2) (°TH) French degree, measure of the water hardness.
3) (mmol/l) millimol per litre, international unit for water hardness
factory
setting
Setting the water softener manually (see table)
The water softener is factory set at position 2.
Set switch to position 1
or 2
8
Setting the water softener electronically (see table)
The water softener is factory set at position 5.
The dishwasher must
be switched off
The End light might
flash 5 times, for
example. The flashing is
repeated every 5
seconds.
Press and hold the start / cancel button and turn
the programme selector dial clockwise till the first
programme. Keep the button pressed until the
programme selector light and the start / cancel light
start flashing.
To change the level,
press the start / cancel
button. Each time the
button is pressed the
level increases. (Level 1
follows level 10).
The End light indicates
the new setting.
Release the button. The
End light will flash. The
number of flashes
corresponds to current
level set.
To memorise the
operation, turn the
programme selector dial
to position off.
9
Filling with dishwasher salt
CAUTION!
Use only special salt suitable for dishwashers
Remove any trace of
salt.
Replace the cap tightly
turning it clockwise until
it stops with a click.
IMPORTANT!
Top up the special salt when the light on the
control panel illuminates.
IMPORTANT!
Water will overflow from the container as salt is
added.
Only before filling with
salt for the first time,
fill the salt container
with water
Using the funnel
provided, pour in the
salt until the container is
filled with salt.
IMPORTANT!
Immediately start a complete programme.
10
Filling with rinse aid
Open the lid. Fill up with rinse aid.
The maximum level for
filling is indicated by
"max".
IMPORTANT!
Top up the rinse aid when the light on the
control panel illuminates.
CAUTION!
Never fill the rinse aid dispenser with any other
substances (e.g. dishwasher cleaning agent, liquid
detergent). This would damage the appliance.
Adjusting the dosage of rinse aid
Increase the dose if there are drops of water or
lime spots on the dishes after washing.
Reduce the dose if there are whitish streaks
on the dishes or a bluish film on glassware or
knife blades.
Clean up any rinse aid
which overflows. Close
the lid and press until it
locks.
Open the lid. Set the dosage level.
(The dose is factory set
in position 4).
Close the lid and press
until it locks.
11
Loading cutlery and dishes
● The following items are not suitable for use
in the dishwasher:
- Cutlery with wooden, horn, china or
mother-of-pearl handles
- Plastic items that are not heat resistant
- Older cutlery with glued parts that are not
temperature resistant
- Bonded cutlery items or dishes
- Pewter or copper items
- Lead crystal glass
- Steel items prone to rusting
- Wooden platters
- Items made from synthetic fibres
● When loading the dishwasher, make sure
that you:
- Remove all left over food and debris.
- Soften remnants of burnt food in pans
- Load hollow items such as cups, glasses,
pans, etc. with the opening downwards so
that water cannot collect in the container
or a deep base.
- Dishes and items of cutlery must not lie
inside one another, or cover each other.
- To avoid damage to glasses, they must
not touch.
- Lay small objects in the cutlery basket.
● Plastic items and pans with teflon have a
tendency to retain water drops; these
items will not dry as well as porcelain and
steel items.
IMPORTANT!
Before closing the door, ensure that the spray
arms can rotate freely.
Load cutlery.
For best results we
recommend you to use
the cutlery grid provided
(if the size and
dimensions of the
cutlery allow it.
12
Place knives and other
items of cutlery with
sharp points or edges
with their handles facing
upwards.
Risk of injury!
Load the lower basket.
Arrange serving dishes and large lids around the
edge of the basket.
Load upper basket.
Light items (plastic
bowls etc.) must be
loaded in the upper
basket and arranged so
they do not move.
For taller items, the cup
racks can be folded
upwards.
If plates are to be loaded in the upper
basket:
load them starting from the rear positions;
tilting them slightly forwards and avoiding the
front positions near the door.
Adjusting the height of the upper basket
If washing very large plates you can load them in the lower basket after moving the upper basket
to the higher position.
Maximum height of the dishes in:
upper basket lower basket
With upper basket raised 20 cm 31 cm
With upper basket lowered 24 cm 27 cm
To move to the higher position proceed as
follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards until the
mechanism is engaged and the basket is stable.
To lower the basket to the original position
proceed as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards and then allow
the mechanism to drop back down slowly,
keeping hold of it.
IMPORTANT!
Never lift or lower the basket on one side only
IMPORTANT!
When the basket is in the higher position you
will not be able to use the cup racks.
13
Filling with detergent
IMPORTANT!
Only use detergents suitable for dishwashers.
Observe the manufacturer’s dosing and storage recommendations.
Open the lid.
For programmes with
prewash add an
additional detergent
dose in compartment B.
When using detergent
tablets:
place detergent tablets
in compartment A.
Unloading the dishwasher
IMPORTANT!
Open the dishwasher’s door, leave it ajar and
wait a few minutes before removing the
dishes; hot dishes are sensitive to knocks. In
this way they will be cooler and the drying will
be improved.
Fill in the detergent in
compartment A.
Close the lid.
● Empty the lower basket first and then the
Observe the dosing
levels.
upper one; this will avoid water dripping from
the upper basket onto the dishes in the lower
one.
● Water may appear on the sides and the door
of the dishwasher as the stainless steel will
eventually become cooler than the dishes.
14
Cleaning and care
Cleaning the filters
IMPORTANT!
NEVER use the dishwasher without filters.
Incorrect repositioning and fitting of the filters will produce poor washing results.
The dishwasher must
be switched off
Remove filter A from the
base of the washing
compartment.
Put the flat filter A back
in the base of the
washing compartment
and ensure that it fits
perfectly under the two
guides D.
IMPORTANT!
NEVER try to remove the spray arms.
If residues of soil have clogged the holes in the
upper spray arm, remove them with a
toothpick.
Clean filters A, B and C
thoroughly under
running water.
Replace the filters and
lock by turning the
handle clockwise to the
stop.
Turn the handle about
1
/4turn anticlockwise
and remove filters B
and C.
15
External cleaning
Clean the external surfaces of the machine and
control panel with a damp soft cloth. If
necessary use only neutral detergents. Never
use abrasive products, scouring pads or
solvent (acetone, trichloroethylene etc....).
Ensure that the seals around the door, the
detergent and rinse aid dispensers are cleaned
regularly with a damp cloth.
We recommend every 3 months to run a 65°C
wash programme without dishes using
detergent.
Prolonged periods of non-operation
If you are not using the machine for any period
of time you are advised to:
1. Unplug the appliance and then turn off the
water.
2. Leave the door ajar to prevent the formation
of any unpleasant smells.
3. Leave the inside of the machine clean.
Environmental concerns
Frost precautions
Avoid placing the machine in a location where
the temperature is below 0°C. If this is
unavoidable, empty the machine, close the
appliance door, disconnect the water inlet pipe
and empty it.
Moving the machine
If you have to move the machine (moving
house etc....):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge
hoses.
4. Pull the machine out together with the
hoses.
5. Only transport the dishwasher in an upright
position, otherwise salt water may run out.
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PE<, >PS<, etc. Please dispose of the
packaging materials in the appropriate
container at the community waste disposal
facilities.
WARNING!
When a unit is no longer being used:
- Pull the plug out of the socket.
- Cut off the cable and plug and dispose of
them.
- Dispose of the door catch.
This prevents children from trapping
themselves inside and endangering their
lives.
16
Old appliance
The symbol on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it shall
be handed over to the applicable collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product.
For more detailed information about recycling
of this product, please contact your local city
office, your household waste disposal service
or the shop where you purchased the product.
Something not working
IMPORTANT!
The dishwasher will not start or stops during operation.
Certain problems are due to the lack of simple maintenance or oversights, which can be solved
with the help of the indications described in the chart, without calling out an engineer.
Switch off the dishwasher, open the door and carry out the following suggested corrective actions.
Fault code / malfunction Possible cause Solution
The water tap is blocked or furred Clean the water tap.
The dishwasher does not fill with
water.
- continuous flashing of the
start / cancel light
- 1 flash of the "End" light
with limescale.
The water tap is turned off. Turn the water tap on.
The filter (where present) in the . Clean the filter in the.
threaded hose fitting at the water threaded hose fitting.
inlet valve is blocked.
The water inlet hose has not been Check the water inlet hose
correctly laid or it is bent or connection.
squashed.
The dishwasher will not drain.
- continuous flashing of the
start/cancel light
- 2 flashes of the "End" light
- continuous flashing of the
start / cancel light
- 3 flashes of the "End" light
The programme does not start.
The sink spigot is blocked. Clean out the sink spigot.
The water drain hose has not been Check the water drain hose
correctly laid or it is bent or connection.
squashed.
Anti-flood device is activated. Close the water tap and
contact your local Service
Force Centre.
The dishwasher door has not been Close the door
properly closed.
The main plug is not plugged in. Insert the mains plug
The fuse has blown in the household Replace the fuse.
fuse box.
Once these checks have been carried out; close the door, switch on the dishwasher and press the
start / cancel button. The programme will continue from the point at which it was interrupted. If
the malfunction or fault code reappears contact the Service Force Centre.
For other combinations of fault codes not described in the above chart, please contact your
Service Force Centre.
17
The dishes are not clean
The dishes are wet and
dull
There are streaks, milky
spots or a bluish coating
on glasses and dishes
Water drops have dried
onto glasses and dishes
The wash results are not satisfactory
●
The wrong washing programme has been selected.
●
The dishes were arranged in such a way as to stop water reaching all parts
of the surface. The baskets must not be overloaded.
●
The spray arm do not rotate freely due to incorrect arrangement of the load.
●
The filters in the base of the washing compartment are dirty or incorrectly
positioned.
●
Too little or no detergent has been used.
●
Where there are limescale deposits on the dishes; the salt container is
empty or the incorrect level of the water softener has been set.
●
The drain hose connection is not correct.
●
The salt container cap is not properly closed.
●
Rinse aid was not used.
●
The rinse aid dispenser is empty.
●
Decrease rinse aid dosing.
●
Increase rinse aid dosing.
●
The detergent may be the cause, Contact the detergent manufacturer’s
consumer care line.
If after all these checks, the problem persists,
contact your local Service Force Centre,
quoting the model (Mod.), product number
(PNC) and serial number (S.N.).
This information can be found on the rating
plate located on the side of the dishwasher
door (see picture).
So that you always have these numbers at
hand, we recommend you to make a note of
them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S.N. :. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
Technical data
Dimensions Width 60 cm
Electrical connection Information on the electrical connection is given on the rating plate on
Voltage - Overall power - Fuse the inner edge of the dishwasher’s door.
Water supply pressure Minimum 0,05 MPa (0.5 bar)
Capacity 12 place settings
Max. weight 41
Noise level 51 dB (A)
Height 85 cm
Depth. 61 cm
Maximum 0,8 MPa (8 bar)
Consumption values
The consumption values are intended as a
guide and depends on the pressure and the
temperature of the water and also by the
variations of the power supply and the amount
of dishes.
Programme Programme duration Energy Water
(minutes) (kWh) (litres)
POWER WASH 70° 85 - 95 1,7 - 1,9 23 - 25
NORMAL WASH 65° 108 - 118 1,7 - 1,8 24 - 26
QUICK WASH 65° 25 - 35 0,7 - 0,8 8
ECO WASH 50°
(Test programme for 140 1,05 18
Test Institutes)
RINSE & HOLD 12 < 0,1 4
19
Hints for test institutes
Testing in accordance with EN 60704 must be
carried out with appliance fully loaded and
using the test programme (see "Consumption
values").
Amount of detergent required: 5 g + 25 g (Type B)
Rinse aid setting: position 4 (Type III)
Upper basket
Cutlery basket
Test in accordance with EN 50242 must be
carried out when the salt container and rinse
aid dispenser have been filled with salt and
rinse aid respectively and using the test
programme (see "Consumption values").
Full load:
12 standard place settings
Lower basket
20
Cup racks: position A
Installation
WARNING!
Any electrical and/or plumbing work required to install this appliance should be carried out by a
qualified electrician and/or plumber or competent person.
Water connection
WARNING!
The dishwasher must not be connected to
open water appliances or instantaneous water
heaters. This dishwasher must be fed with cold
WARNING!
Only use, for connection to the water mains,
new hose-set; old hose-set must not be
reused.
water.
CAUTION!
If the machine is connected to new pipes or pipes which have not been used for a long time, you
should run the water for a few minutes before connecting the inlet hose.
Inlet hose
Connect the inlet hose to a water tap with an
external thread of 3/4”.
The inlet hose can be turned either to the left or the
right to suit the installation by means of the locknut.
The locknut must be correctly fitted to avoid water
leaks.
Drain hose
- Connect drain hose to the sink. Secure it with the
supplied hose clamp.
- Required height: 30 to 100 cm above bottom of
the dishwasher.
- If you use a drain hose extension the total length
should not be longer than 4 metres. Likewise the
internal diameter of the couplings used for
connections to the waste outlet must be no
smaller than the diameter of the hose provided.
21
Ensure that the hoses
are not kinked, crushed
or entangled.
Electrical connection
WARNING!
Safety standards require the appliance to be
earthed. The manufacturer accepts no liability
for failure to observe the above safety
precautions.
Prior to using the appliance for the first time,
ensure that the rated voltage and type of
supply on the rating plate match that of the
supply where the appliance is to be installed.
The fuse rating is also to be found on the rating
plate.
Always plug the mains plug into a correctly
installed shockproof socket.
CAUTION!
Always be sure, that there is no water leakage
from hoses and their connections after the
installation.
WARNING!
Multi-way plugs, connectors and extension
cables must not be used. This could constitute
a fire hazard through overheating.
If necessary, have the domestic wiring system
socket replaced. In case that the electrical
cable has to be replaced, contact your local
Service Force centre.
The plug must be accessible after the
appliance has been installed.
Never unplug the appliance by pulling on the
cable. Always pull the plug.
22
Fitting under a counter
By removing the dishwasher’s worktop, you
can install it under a close fitting sink unit or a
pre-existing top.
Unscrew the two screws
at the rear.
Levelling
Good levelling is essential for correct
closure and sealing of the door.
When the appliance is correctly levelled,
the door will not catch on either side of the
cabinet.
Be sure that once the appliance has been
installed, it is easily accessible for the service
engineer in the event that a repair is required.
Push the top backwards
about 1 cm.
Check if the dishwasher
is levelled.
Lift top at the front and
remove it.
If not, loosen or tighten
the adjustable feet until
the appliance is
perfectly levelled.
23
Service and spare parts
In the event of your appliance requiring
service, or if you wish to purchase spare parts
please contact your local Service Force Centre
by telephoning:
08705 929929
Your telephone call will be automatically routed
to the Service Force Centre covering your post
code area.
For the address of your local Service Force
Centre and further information about Service
Force, please visit the website at
.serviceforce.co.uk
www
Before calling out an engineer, please ensure
you read the details under the heading
"Something not working".
When you contact the Service Force Centre
you will need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the
appliance (found on the rating plate)
5. The purchase date
Customer Care Department
For general enquiries concerning your Tricity
Bendix appliance or for further information on
Tricity Bendix products please contact our
Customer Care Department by letter or
telephone at the address below or visit our
website at www.tricity-bendix.co.uk
Customer Care Department
Major Appliances
Tricity Bendix
Addington Way
Luton
Bedfordshire
LU4 9QQ
Tel: 08705 950950 (*)
calls to this number may be recorded for training purposes
*
Please note that a valid purchase receipt or
guarantee documentation is required for inguarantee service calls.
For Customer Service in The Republic of
Ireland please contact us at the address below:
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: + 353 (0)1 4090751
Email: service.eid@electrolux.ie
24
Guarantee conditions
Standard Guarantee Conditions
We, Tricity Bendix, undertake that if within 12
months of the date of purchase this Tricity
Bendix appliance or any part thereof is proved
to be defective by reason only of faulty
workmanship or materials, we will, at our
option repair or replace the same FREE OF
CHARGE for labour, materials or carriage on
condition that:
● The appliance has been correctly installed
and used only on the electricity supply stated
on the rating plate.
● The appliance has been used for normal
domestic purposes only, and in accordance
with the manufacturer’s instructions.
● The appliance has not been serviced,
maintained repaired, taken apart or
tampered with by any person not authorised
by us.
● All service work under this guarantee must
be undertaken by a Service Force Centre.
● Any appliance or defective part replaced
shall become the Company’s property.
● This guarantee is in addition to your
statutory and other legal rights.
Exclusions
This guarantee does not cover:
● Damage or calls resulting from
transportation, improper use or neglect, the
replacement of any light bulbs or removable
parts of glass or plastic.
● Costs incurred for calls to put right an
appliance which is improperly installed or
calls to appliances outside the United
Kingdom.
● Appliances found to be in use within a
commercial environment, plus those which
are subject to rental agreements.
● Products of Tricity Bendix manufacture which
are not marketed by Tricity Bendix.
Home visits are made between 8.30am and
5.30pm Monday to Friday. Visits may be
available outside these hours in which case a
premium will be charged.
25
European guarantee
This appliance is guaranteed by Electrolux, in
each of the countries listed in the following
page, for the period specified in the appliance
guarantee or otherwise by law. If you move
from one of these countries to another of these
countries the appliance guarantee will move
with you subject to the following qualifications:
● The appliance guarantee starts from the date
you first purchased the appliance which will
be evidenced by production of a valid
purchase document issued by seller of the
appliance.
● The appliance guarantee is for the same
period and to the same extent for labour and
parts as exists in your country of residence
for this particular model or range of
appliances.
● The appliance guarantee is personal to the
original purchaser of the appliance and
cannot be transferred to another user.
● The appliance is installed and used in
accordance with instructions issued by
Electrolux and is only used within the home,
i.e. is not used for commercial purposes.
● The appliance is installed in accordance with
all relevant regulations in force within your
new country of residence.
The provisions of this European Guarantee do
not affect any of the rights granted to you by
law.
26
www.electrolux.com
Albania +35 5 4 261 450 Rr. Pjeter Bogdani Nr. 7 Tirane
Belgique/België/Belgien +32 2 363 04 44 Bergensesteenweg 719, 1502 Lembeek
Česká republika +420 2 61 12 61 12 Budějovická 3, Praha 4, 140 21
Danmark +45 70 11 74 00 Sjællandsgade 2, 7000 Fredericia
Deutschland +49 180 32 26 622 Muggenhofer Str. 135, 90429 Nürnberg
Eesti +37 2 66 50 030 Mustamäe tee 24, 10621 Tallinn
España +34 902 11 63 88 Carretera M-300, Km. 29,900
France www.electrolux.fr
Great Britain +44 8705 929 929 Addington Way, Luton, Bedfordshire
Hellas +30 23 10 56 19 70 4 Limnou Str., 54627 Thessaloniki
Hrvatska +385 1 63 23 338 Slavonska avenija 3, 10000 Zagreb
Ireland +353 1 40 90 753 Long Mile Road Dublin 12
Italia +39 (0) 434 558500 C.so Lino Zanussi, 26 - 33080 Porcia (PN)
Latvija +37 17 84 59 34 Kr. Barona iela 130/2, LV-1012, Riga
Lietuva +370 5 27 80 609 Verki˜ 29, LT-09108 Vilnius
Luxembourg +35 2 42 43 13 01 Rue de Bitbourg, 7, L-1273 Hamm
Magyarország +36 1 252 1773 H-1142 Budapest XIV, Erzsébet királyné útja 87
Nederland +31 17 24 68 300 Vennootsweg 1, 2404 CG - Alphen aan den Rijn
Norge +47 81 5 30 222 Risløkkvn. 2, 0508 Oslo
Österreich +43 18 66 400 Herziggasse 9, 1230 Wien
Polska +48 22 43 47 300 ul. Kolejowa 5/7, Warsaw
Portugal +35 12 14 40 39 39 Quinta da Fonte - Edificio Gonçalves Zarco -
Romania +40 21 451 20 30 Str. Garii Progresului 2, S4, 040671 RO
Schweiz/Suisse/Svizzera +41 62 88 99 111 Industriestrasse 10, CH-5506 Mägenwil
Slovenija +38 61 24 25 731 Electrolux Ljubljana, d.o.o.
Slovensko +421 2 43 33 43 22 Electrolux Slovakia s.r.o., Electrolux
Suomi +35 8 26 22 33 00 Konepajanranta 4, 28100 Pori
Sverige +46 (0)771 76 76 76 Electrolux Service, S:t Göransgatan 143,
Türkiye +90 21 22 93 10 25 Tarlabafl› caddesi no : 35 Taksim Istanbul
–ÓÒÒˡ +7 495 9377837 129090 ГУТН‚‡, ŒОЛПФЛИТНЛИ ФУТФВНЪ,
Alcalá de Henares Madrid
LU4 9QQ
Q 35 - 2774 - 518 Paço de Arcos
Tržaška 132, 1000 Ljubljana
Domáce spotrebiče SK,
Seberíniho 1, 821 03 Bratislava
S-105 45 Stockholm
16 ¡ч СŒОЛПФЛНо
27
www.electrolux.com
www.tricity-bendix.co.uk
Subject to change without notice156998 37/0
Loading...