Page 1
Flat Par 7x3W
Copyright triAngle lights
Last updated on Mach 28
th
2012
triangle.lights@gmail.com
1/8 Copyright 2011 triAngle lights
1. INTRODUCTION
Please read this user manual carefully and thoroughly before
operation.
1.1 What is Included
a) 1X flat par 7x3w with lead
b) 1X user manual
Carefully unpack the carton, check the contents to ensure that all
parts are present and in good condition. Contact your supplier if any
part is missing or damaged.
1.2 Safety Instructions
▪ This product is intended for indoor use only!
▪ Always turn off, unplug power and allow fixture to cool before
servicing.
▪ Ensure that fixture is properly grounded.
▪ Please keep this User Guide for future reference.
▪ Always make sure that you are connecting to the proper voltage
and that the line voltage you are connecting to is not higher than that
stated on decal or rear panel of the fixture.
▪ To prevent risk of fire or shock, do not expose fixture to rain or
moisture.
▪ Make sure power cord is never crimped or damaged.
▪ Do not look into the beam from a distance of less than 40 cm (16
inches).
WARNING!!! To reduce risk of fire, electric shock, or
injury, follow these important safety instructions
Page 2
2/8 Copyright 2011 triAngle lights
1.3 Product Features
▪ Super bright 3W RGBW leds
▪ 4 modes: Sound, Auto, DMX, Master/Slave
▪ DMX 3/6CH
▪ Linear dimmer 0-100%
▪ Digital LED Display
▪ IP20 rating
▪ Power failure memory
3/8 Copyright 2011 triAngle lights
2. SET UP
2.1 Mounting
With adjustable mounting double brackets, this unit may be wall
mounted, free standing, or clamp mounted.
IMPORTANT!!! Safety cables must always be used. The safety
cable must be capable of holding 10 times the weight of the
fixture.
2.2 Fixture Linking
To run your light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures in master/slave
operating mode, you need DMX cables to link the units from DMX IN to
DMX OUT.
2.3 AC Power
The fixture is designed to work on 100V-240V 50/60Hz.
Warning!!! All fixtures must be connected to circuits
with a suitable Earth Ground.
Page 3
4/8 Copyright 2011 triAngle lights
3 OPERATION INSTRUCTIONS
3.1 Menu Map
Display Function
A00R
A001-A255 7CH mode, A001 also for slave mode
B001-B255 3CH mode
RL Red Dimmer
GL Green Dimmer
BL Blue Dimmer
FLAS Color Change Auto Run
FADE Color Fading Auto Run
SOUA
Sound Mode with Color Changing Effects, no sound static
light
SOUF Sound Mode with Color Fading Effects, no sound no light
3.2 Auto Mode
In this mode, you can set the unit to run in static colors, strobe, or do
color changing without a dmx controller.
1. Press MENU button until display reads: “ FLAS ” or “FADE”.
2. Press Enter button and use UP/DOWN button to select FL00 to FL12, or
FA00 to FA12 for different speed.
3.3 Dmx Mode
In DMX mode, you can control the fixture with a DMX controller.
1. Press MENU button until display reads: “ A00R ”.
2. Then press Enter button to reach “A xxx” for 7CH mode and use
Up/Down button to set DMX address for the fixture. Similarly, Bxxx for 3CH
mode.
5/8 Copyright 2011 triAngle lights
Dmx Table: 7CH
Ch1 0-255 Master Dimmer
CH2 0-255 Master Strobe
Ch3 0-255 Red dimmer
Ch4 0-255 Green dimmer
Ch5 0-255 Blue dimmer
Ch6
0-100 Color change
101-150 Color fade
151-200 Sound active mode 1
201-255 Sound active mode 2
Ch7 0-255 Auto run speed for selected program
* Master dimmer must be on for Ch2-Ch6 to work
Dmx Table: 3CH
Ch1 0-255 Red dimmer
Ch2 0-255 Green dimmer
Ch3 0-255 Blue dimmer
3.4 Master/Slave Mode
In this mode, multiple units can be linked together as one system and
run in sync. Maximum 31pcs can be linked in a daisy chain as
Master/Slave system.
1. Use DMX cable to link your Armor pars together from DMX OUT to DMX
IN connector.
2. One of the fixtures is to be set as Master and this Master unit needs to
work under Auto , Static Color mode. Others are to be set Slave mode
(A001).
3. Operate the Master fixture to run the whole system.
Page 4
6/8 Copyright 2011 triAngle lights
4.SERVICING
4.1 Fuse Replacement
1. Unscrew the fuse holder and remove the damaged fuse.
2. Replace with exact same type fuse and screw the fuse holder back in
its place.
4.2 Cleaning
To maintain optimum performance fixtures should be cleaned
frequently.
Unplug fixture from power and allow the fixture to cool down. Use a
vacuum or air compressor and a soft brush to remove dust collected on
the plastic cover or lens.
4.3 Trouble Shooting
1. Unit does not respond to DMX:
Check that the DMX cables are connected properly and are wired
correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’).
It does matter which way the inputs and outputs are connected.
Disconnect from mains before servicing.
7/8 Copyright 2011 triAngle lights
5.TECHNICAL SPECIFICATIONS
WEIGHT&DIMENSIONS
Length 20cm
Depth 20cm
Height 12cm
Weight 1.5kg
POWER
AC Power AC110-240V 50/60Hz
Power Consumption 40w MAX.
Fuse
LIGHT SOURCE 7x3W rgb leds
Beam Angle 25 degree
IMPORTANT INFORMATION!
In order to optimize the recovery and recycling of the materials that
old appliances contain and reduce the impact on human health
and the environment, ensure that this product is recycled at the
end of its life.
N INTRODUCTIO
Loading...