Page 1
R
TRIAD
Printing Forms with the
Pacemark 3410 Printer
Page 2
This manual contains reference information about Triad’s hardlines and lumber
line of software products. The software described in this manual, as well as the
manual itself, are furnished under the terms and conditions of a license agreement. The software consists of software options which are separately licensed. It
is against the law to copy the software on any medium, or to enable any software
options, except as specifically permitted under the license agreement. In addition, no other part of this manual may be copied or transmitted in any form or by
any means without the prior written permission of Triad.
From time to time, Triad makes changes to its software products. Therefore,
information in this manual is subject to change, and the illustrations and screens
which appear in the manual may differ somewhat from the version of the software provided to you.
Created by
Learning Products Development
for Triad Systems Corporation
©
Copyright
1995 Triad Systems Corporation. All rights reserved. Printed in the
United States of America.
Triad and the stylized logo are registered trademarks of Triad Systems Corporation.
Eagle™ is a trademark of Triad Systems Corporation.
Hardlines and Lumber Division
3055 Triad Drive
Livermore, CA 94550-9559
Publication No. 1075183
Revision No. 4902
Page 3
V
V
V
V
V
V
V
Printing Forms with the
Pacemark 3410 Printer
Printinting Forms with the Pacemark 3410 Printer
This document explains how to print forms on the Triad system with the
Pacemark 3410 Printer. Insert this document into the
System
printer, see the
To print a form, refer to the Printing Forms table on page 2 to:
, the tabbed section, Printers. For additional information about the
Pacemark 3410 Printer Handbook,
V Identify the form to print.
Determine the printer settings.
Guide to Your Triad
which came with the printer.
Identify the form used for the report.
For additional information, see:
“Using Printer Menus” on page 3.
“Changing Printer Settings” on page 4.
“Identifying Triad Default Printer Settings” on page 5.
“Printing Current Printer Settings” on page 6.
“For More Information about Printing Forms” on page 7.
Printinting Forms with the Pacemark 3410 Printer
1
Page 4
V
V
V
Printing Forms
To use the Printing Forms table below, read:
For this form... to identify the form you wish to print.
Use these printer settings... to identify the printer settings required to
print the form. Sometimes the printer settings for the DX10 system differ
from those for the Eagle system and are indicated as such in this column.
Use for this report... to determine the form used for a report.
For additional information about printing forms, see “Using Printer Menus” on
page 3 and “Changing Printer Settings” on page 4.
Printing Forms
For this
form...
8 1/2 x 11 inch
paper
15 x 8 1/2 inch
paper
Accounts
Payable Checks
Accounts
Receivable
Statements
Accounts
Receivable
Mailing Labels
Use these
printer settings...
Change CPI to 17
Leave all others at Triad
defaults
Change LPI to 8
Leave all others at Triad
defaults
If DX10, change LPI to 8
If Eagle, change LPI to 6
Leave all others at Triad
defaults
Leave at Triad defaults RSM (Statement Report)
Leave at Triad defaults RML (Customer Mailing
Use for this report...
All reports
All reports
If DX10, RACK (Check
Processing)
If Eagle, APCM (Check
Processing)
Labels Report)
Bin Labels Change LPI to 8
Leave all others at Triad
defaults
Invoices Change CPI to 17
Leave all others at Triad
defaults
2
RBL (Bin Label Printing
Report)
POS (Point-of-Sale)
invoices
CPOS (Contractor Pointof-Sale) invoices
Printing Forms
Page 5
If you skip a menu setting, keep pressing the
appropriate menu button to cycle through the
menu again.
Tip
Printing Forms ( continued )
For this
form...
Use these
printer settings...
Use for this report...
Payroll Checks Leave at Triad defaults If DX10, PRM #4 (Payment
Processing)
If Eagle, PPTU (Payment
Processing)
Price Labels Leave at Triad defaults RLA (Price Label Printing
Report)
W-2 Forms Change LPI to 8
Leave all others at Triad
defaults
If DX10, PRM #10 (Print
Year-End W-2 Forms)
If Eagle, RPW2 (Print YearEnd W-2 Forms)
Using Printer Menus
You need to know how to use printer menus to change printer settings. The
printer menus are directories of printer features. Menus are organized into
three levels, which correspond to these printer buttons:
Use the buttons on the front panel of the printer to change printer settings as
shown in the table below.
GROUP
,
ITEM
, and
SET
.
The
can use them. To activate these buttons, press
PITCH
printer paper indicating the buttons are activated.
The
(CPI), is ready for use and does not require activation.
For an example of how to change a printer setting, see “Changing Printer
Settings” on page 4.
Printer Button How to use it...
GROUP
ITEM
SET
EXIT
Using Printer Menus
,
,
,
GROUP
ITEM
SET
EXIT
, and
buttons must be activated before you
PRINT
PRINT
QUALITY
and
CHARACTER
on the front printer panel at the same time. Menu Mode prints on the
CHARACTER
PITCH
button, which is used to change the characters per inch
Press repeatedly to cycle through the groups in the
menu. Stop when the setting you want prints on
the printer paper.
Press to change an item within a group.
Press to change an item setting.
Press to save the printer settings and return to
print mode.
3
Page 6
1.
2.
3.
4.
5.
Printer Button
PRINT
How to use it... ( continued )
Press to print a complete listing of the current
printer settings.
CHARACTER
PITCH
Press to change the CPI.
Depending on your printer settings, this button
may not highlight the CPI you want to select.
If you are unable to use
CHARACTER
PITCH
to
change a CPI setting, follow the example in
“Changing Printer Settings.”
Changing Printer Settings
Depending on the form you want to print, you may need to change the printer
settings. Use the printer buttons as shown in the previous table to change
. The printer
printer settings. After selecting all appropriate settings, press
settings are saved and you are ready to print the form.
The example below shows you how to change the CPI for 8 1/2 x 11 inch paper
from CPI 10 to CPI 17. Use the same procedure shown in this example to
change any printer setting.
EXIT
Tip
If you skip a menu setting, keep pressing the
appropriate menu button to cycle through the
menu again.
PRINT
Press
QUALITY
and
CHARACTER
PITCH
at the same time to enter Menu
Mode.
Menu Mode prints on the printer paper. You can use
PRINT
Press
EXIT
, and
PRINT
to change printer settings.
to print the current printer settings.
GROUP
ITEM
,
,
SET
,
Use the list of current printer settings to identify menus and to determine
which settings you need to change. For example, if you are changing the
CPI, change all occurrences of the CPI shown on the printout.
You can also use the Pacemark 3410 Triad Default Printer Settings table on
page 5 to identify printer menus, and as a reference to the Triad default
printer settings.
Refer to the Printing Forms table on page 2 to determine the CPI for
8 1/2 x 11 inch paper. The table indicates that the CPI should be changed
from CPI 10 (the default) to CPI 17.
Press
until the text on the printer paper matches the example below:
GROUP
Printer Mode Emulation EPSON FX
Font Print Mode HSD
Press
until the text on the printer paper matches the example below:
ITEM
Printer Mode Emulation EPSON FX
Pitch I 10 CPI
(or any CPI)
4
Changing Printer Settings
Page 7
6.
7.
8.
Press
Press
Menu End prints on the printer paper. You are ready to print the form.
Run the report from the terminal.
The form prints. These printer settings remain until you change them.
Use the same procedure to change any printer setting. Make sure that you
change all appropriate settings before you press
until the CPI is 17.
SET
to save the printer settings and return to Print Mode.
EXIT
.
EXIT
Identifying Triad Default Printer Settings
Use the Pacemark 3410 Triad Default Printer Settings table below to identify
printer menus, and as a reference to the Triad default printer settings.
Pacemark 3410 Triad Default Printer Settings
GROUP
Printer Mode Emulation EPSON FX
ITEM
SET
Font Print Mode
Pitch
Style
Size
Symbol Sets Character Set
Language Set
Zero Character
Code Page
Rear Feed Line Spacing
Form Tear-Off
Skip Over Perforation
Page Width
Page Length
Bottom Feed Line Spacing
Form Tear-Off
Skip Over Perforation
Page Width
Page Length
Top Feed Line Spacing
Form Tear-Off
Skip Over Perforation
Page Width
Page Length
HSD
10 CPI
Normal
Single
Set I
American (USA/CANADA)
or British (U.K.)
Slashed
USA
6 LPI
Off
No
13.6"
11"
6 LPI
Off
No
13.6"
11"
6 LPI
Off
No
13.6"
11"
Identifying Triad Default Printer Settings
5
Page 8
Pacemark 3410 Triad Default Printer Settings ( continued )
GROUP
ITEM
SET
1.
2.
Set-Up Graphics
Receive Buffer Size
Paper Out Override
Print Registration
Operator Panel Function
Reset Inhibit
Print Suppress Effective
Auto LF
CSF Bin Select
Time Out Print
Auto Select
Sensor Disable
Serial I/F Parity
Serial Data 7 or 8 Bits
Protocol
Diagnostic Test
Busy Line
Baud Rate
DSR Signal
DTR Signal
Busy Time
Bi-directional
28K
No
0.00 mm
Full Operation
No
Yes
No
Bin 1
Valid
No
No
None
7 Bits
Ready/Busy
No
SSD9600
Invalid
Ready On Power Up
200 ms
Printing Current Printer Settings
Use the list of current printer settings to identify menus and to determine
which settings you need to change. For example, if you are changing the CPI,
change all occurrences of the CPI shown on the printout.
You can also use the Pacemark 3410 Triad Default Printer Settings table on
page 5 to identify printer menus, and as a reference to the Triad default
printer settings.
To print the current printer settings:
Press
Mode.
Menu Mode prints on the printer paper.
Press
PRINT
QUALITY
to print the current printer settings.
PRINT
and
CHARACTER
at the same time to enter Menu
PITCH
6
Printing Current Printer Settings
Page 9
For More Information about Printing Forms
If you have questions about printing forms with the Pacemark 3410 printer,
you can:
Refer to the Pacemark 3410 Printer Handbook, which came with the
printer.
V
Call the Triad Advice Line at 1 (800) 678-7423.
V
or
For More Information about Printing Forms
7
Loading...