OWNER’S MANUAL
Before using this product, please read
and understand the entire manual
WARNING: Riding scooters can be a hazardous activity. Scooters are
a moving vehicle and therefore it is possible for the user to get into
dangerous situations and/or lose control and/or fall. If such things occur,
the user and/or other persons can be seriously injured or killed. LIKE ANY
OTHER MOVING VEHICLE, USING A SCOOTER CAN BE A DANGEROUS
ACTIVITY AND MAY RESULT IN INJURY OR DEATH EVEN WHEN USED
WITH PROPER SAFETY PRECAUTIONS, USE AT YOUR OWN RISK AND
USE COMMON SENSE
• Safety equipment such as helmet, knee pads, wrist pads should be worn at all times.
• Always ride on smooth and paved surfaces away from motor vehicles.
• Scooter may encounter pitching motion/wheel entrapment or suddenly stop if it comes into contact
with sharp bumps, rocks/sticks, sudden surface changes or drains.
• Never ride on surfaces where there is water, sand, gravel, dirt, leaves or other debris. Use while
raining impairs traction, braking and visibility.
• Brake by putting pressure down on the rear flex brake with your foot connecting brake with the
wheel. Brake will get hot from continuous use. Do not touch after braking.
• Avoid excessive speed associated with downhill rides.
• Adults should assist children in assembling this scooter.
• Always obey all local traffic laws and regulations.
• Respect pedestrians while riding on footpaths.
• Replace worn or broken parts immediately.
• Do not exceed 220 pounds (100kg).
• Children under the age of eight years old should not use this scooter without adult supervision.
Adult guidance is advised for all children using this scooter.
• It’s the parents decision to allow his or her child to ride this product. It’s also their responsibility to
judge if the child’s maturity, skill and ability is suitable and safe to ride this product.
• This scooter was manufactured for performance and durability, however not impervious to damage.
Stunt riding can over stress or damage any product, including this scooter and the rider assumes
all risks associated with high-stress activity.
WARNING
SAFETY
Parental supervision is required. Always wear personal protective equipment when riding
a scooter. Only use the scooter in a controlled environment that is free of potential traffic
hazards and not on public streets. Avoid use in any areas where there are any motor
vehicles operating. Have two hands on the handle bars at all times. Never allow more
than one child at a time to ride the scooter. Never use near steps, slopes, driveways, hills,
roadways, alleys or swimming pool areas.
Do not ride a scooter in wet weather. Scooters are intended and made to be used on
concreted or smoothed paved areas that are flat, clean and dry, free from any loose
debris such as rocks, sticks or gravel. Wet, slick or uneven and rough surfaces may
impair traction and contribute to possible accidents. Avoid riding this scooter in mud, ice,
puddles or water. Avoid excessive speeds that can be associated with downhill rides. Do
not ride at night or when visibility is impaired.
Always ensure child is wearing proper protective equipment such as a certified safety
helmet. A helmet may be legally required by local law, we advise you to check with your
local law enforcement. User should always wear shoes that are fully enclosed with flat
soles.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS FURTHER
INCREASES RISK OF SERIOUS INJURY. USE AT YOUR OWN RISK AND WITH
APPROPRIATE AND SERIOUS ATTENTION TO SAFE OPERATION. USE CATION.
WARNING: ALWAYS INSPECT SCOOTER PRIOR TO RIDING. Proper inspection and
maintenance of your scooter can reduce the risk of injury. Always inspect your scooter
before riding and regularly maintain it.
RIDING SMART SAFETY EQUIPMENT
Tightening your compression:
If your bars start to shake or move side to side, this means your compression needs to be tightened. Do so by
removing your handle bars and using a allen key to tighten the compression ring. Turning it in a clock- wise
direction, tighten until some pressure is felt in the allen key. You want to be able to still spin your forks freely,
however if over tightened, you can restrict the movement and damage your compression or headset. This
should be done by an adult or a professional mechanic.
Lubricating your bearings:
You will need to take off your wheels to lubricate your wheel bearings. Insert the 6mm allen keys, in each axle
head and turn them anti clock- wise (1x6mm for rear axle). The wheels may need some encouragement to slide
out. Using a damp cloth wipe off any dirt or grime on your wheels and bearings. Using bicycle bearing oil,
place 3 to 4 drops directly on the bearing covers and allow the oil to sink in. If the wheels do not spin freely
after this you may need to replace the bearings.
Cleaning your scooter:
Never use alcohol or any strong cleaning agents to clean your scooter. Doing so may damage paint or fragile
materials. Warm water and a damp cloth should be enough. Avoid putting water directly on the grip tape and
never submerge your scooter in water.
SAFETY REMINDERS –
When using this scooter for the first time, check that all the bolts are tightened. Inspect all moving parts,
including wheels and headset and ensure they are operating smoothly. -Check and secure all bolts before
every ride. Loose parts may damage your scooter or increase the risk of a fall. - Replace worn or broken parts
immediately. - Ensure you are wearing all required safety equipment before operating this scooter.
MAINTENANCE
Once the clamp is firlmy in position
tighten bolts to 8Nm with 6mm hex key
Insert handlebar & clamp
to the fork using the indicators
for precision alignment
Laser etched
center alignment
indicators
21
Instructional diagram for Infraction
Tightening order - 1,2 with quarter turns,
repeat this process to ensure both bolts are
tightened equally
Once the clamp is firmly in position
tighten bolts with a 6mm hex key
Once the clamp is firlmy in position
tighten bolts to 8Nm with 6mm hex key
Insert handlebar
and align the indicators
for precision alignment
Laser etched
center alignment
indicators
21
Insert handlebar & clamp
to the fork using the indicators
for precision alignment
Laser etched
center alignment
indicators
21
*Your scooter may vary from those illustrated,
however the assembly procedure is the same
*Do not over tighten any bolts on this scooter.
We recommend you always use a torque wrench
to measure the tightness of each bolt. We
recommend all bolts to be tightened to 10Nm.
Over tightening bolts can result in damaging the
bolt and or part.
Once the clamp is firmly in position
tighten bolts with a 6mm hex key
*Do not over tighten any bolts on this
scooter. We recommend you always use
a torque wrench to measure the tightness
of each bolt. We recommend all bolts to be
tightened to 10Nm. Over tightening bolts can
result in damaging the bolt and or part.
*Your scooter may vary from those illustrated,
however the assembly procedure is the same
Instructional diagram for HIC/IHC Instructional diagram for SCS
Tightening order - 1,2 with quarter turns,
repeat this process to ensure both bolts are
tightened equally
Tightening order - 1,3,2,4 with quarter turns,
repeat this process to ensure all bolts are
tightened equally
Once the clamp is firmly in position
tighten bolts with a 6mm hex key
WARRANTY
At Triad Scooters we take great pride in the quality and build integrity of our products
and back it with a manufacturer’s warranty which covers all manufacturing faults and
defects. Our manufacturer’s warranty can vary depending on the product and is only
from the original date of purchase (receipt required). This does not apply to normal wear
and tear, malfunctions or failures that result from abuse, neglect, improper assembly,
improper maintenance, alteration, collision, corrosion, crash or misuse. Installation of
components, parts, or accessories not originally intended for use with or compatible with
Triad Scooters and components will void any warranty offered.
For our full warranty policy please visit triadscooters.com for more information
Congratulations on selecting a Triad Scooter.
Please scan the relevant QR Code below to access a guided
instructional assembly video that will help you complete the assembly
of your TRIAD Scooter.
Once you have a QR Code reader installed on your device, your ready to scan
your instructional assembly video QR Code.
Follow these simple steps.
1. Open the QR Code reader on your device
2. Hold your device over the QR Code so that it’s clearly visible within your
device’s screen. Two things can happen when you have the QR Code in the
correct place - The phone automatically scans the code. Or, on some readers, you
have to press a button to snap a picture.
3. Your device will read the code and navigate to the video using your web browser
4. The video will then open and all you need to do is watch, assemble and ride!
QR Code for IHC assembly
www.triadscooters.com/qr/ihcassembly/ www.triadscooters.com/qr/scsassembly/
QR Code for SCS assembly
EN 14619
Loading...