Trenton TPLP Series Product Data And Installation Instructions

Download

Page 1

PRODUCT DATA &

23/12/16

INSTALLATION

Bulletin T30-TPLP-PDI-11

TPLP Pre-Assembled

Low Prole

Evaporators

1087152

Questions about this product?

Email: evaps@t-rp.com

Call: 1-844-893-3222 x520

Air & Electric Defrost

Electrical Power: 115/1/60, 208-230/1/60, 208-230/3/60, 460/1/60

See Page 22 for details

CONTENTS Page

Nomenclature................................................................................................................... 2

Features & Options.......................................................................................................... 2

Pre-Assembled Features................................................................................................. 3

Capacity Data.................................................................................................................. 4

Electrical Data.................................................................................................................. 5-7

Wiring Diagrams - Models with standard PSC motors .................................................... 8-15

Wiring Diagrams - Models with optional EC Motors /

Shipping Weights............................................................................................................. 20

Dimensional Data............................................................................................................. 21-22

Recommended Expansion Valve Selections................................................................... 23

Installation Instructions.................................................................................................... 24-25

Generic Service Parts ..................................................................................................... 26

Warranty........................................................................................................................... 27

Project Information........................................................................................................... 27

“As Built” Service Parts.................................................................................................... Back

.............................. 16-19

Page 2

NOMENCLATURE

23/12/16

T30-TPLP-PDI-11

- 2 -

TPLP

T = Trenton

Pre-Assembled

Low Prole Evaporator

Number of Fans Nominal Capacity:

x 1000 @ 10°F TD, Btu/H, R404A

Application Range:

M = Medium to High Temp 6 FPI (10°F to 45°F (-12°C to 7°C) Evap Temp) L = Low Temp 6 FPI (-40°F to 0°F(-40°C to -17°C) Evap Temp) V = Low Temp 4 FPI (-40°F to 0°F (-40°C to -17°C) Evap Temp)

T P LP 3 15 L E S2 B R6 - PSC

STANDARD FEATURES

60Hz

Motor Designation:

PSC = PSC Permanent Split Capacitor EC2 = EC Motor

Refrigerant Designation:

R2 = R407A / R407C / R22 R6 = R404A R7 = R407A

Generation: B = 2

Voltage:

S1 = 115/1/60 (air defrost models only) S2 = 208-230/1/60 S4 = 460/1/60 (2 to 6 fan models only) T3 = 208-230/3/60

Defrost*:

A = Air E = Electric

• Compatable with Low GWP Refrigerants

• PSC motors

• Streamlined cabinet style

• Highe󰀩ciency,durablefanguard

• Front access

• Compact

• Internally enhanced tubing

• Spacious electrical and refrigeration compartments

• Low heater wattage

• Proven motor/fan/motor mount design

OPTIONAL FEATURES

• EC motors with patented SmartSpeed® Technology. See page 16

• Heat exchanger - shipped loose

• Heresite Coating

• Factory installed expansion valve,

solenoid valve and room thermostat

• Schrader valve on suction header

• Positive slope, hinged drain pan

• Central drain connections (approximate)

• 3/4”IDUniversaldrainttingfor3/4”MPT

 or3/4”aretting

• Factory installed distributor nozzle

• 460/1/60 PSC motor only

• Copper or GW Aluminum “Gold Coat” Fins

• Wire fan guard

• Painted Cabinet

Page 3

TPLP

23/12/16

T30-TPLP-PDI-11

- 3 -

PRE-ASSEMBLED FEATURES

60Hz

Thermostat Mounted on Front of Unit

Solenoid Valve and TXV Mounted

Solenoid Valve Wire pulled through and labeled on each end

Schrader Valve Located Outside

Page 4

CAPACITY DATA - ALL MODELS

23/12/16

T30-TPLP-PDI-11

- 4 -

TPLP

Medium Temperature Models - Capacity @ 6 F.P.I. *

Medium Temp. Models 104M 106M 107M 209M 211M 214M 317M 320M 423M 426M 532M 639M Number Of Fans 1 1 1 2 2 2 3 3 4 4 5 6

R407A

Capacity

BTUH

(WATTS)

Evap

Temp.

25°F

(-4°C)

R407C

R404A

R507

R22

Air Flow CFM (L/S) Refrigerant **

Charge

R407A

LB. (KG)

Low Temperature Models - Capacity @ 6 F.P.I. *

Low Temp. Models 104L 105L 106L 207L 209L 211L 314L 317L 419L 422L 527L 631L Number Of Fans 1 1 1 2 2 2 3 3 4 4 5 6

Capacity

BTUH

(WATTS)

Air Flow CFM (L/S) Refrigerant **

Charge

Evap

Temp.

-20°F

(-29°C)

R407A

R404A

R507

LB. (KG)

4090 5230 6460 8170 10450 13300 16200 19000 21900 24700 30400 37100

(1197) (1530) (1891) (2394) (3059) (3895) (4731) (5567) (6403) (7230) (8902) (10830)

3870 4950 6120 7740 9900 12600 15400 18100 20800 23500 28900 35200

(1134) (1449) (1791) (2268) (2898) (3690) (4482) (5274) (6066) (6849) (8433) (10260)

4300 5500 6800 8600 11000 14000 17000 20000 23000 26000 32000 39000

(1260) (1610) (1990) (2520) (3220) (4100) (4980) (5860) (6740) (7610) (9370) (11400)

4090 5230 6460 8170 10500 13300 16200 19000 21900 24700 30400 37100

(1197) (1530) (1891) (2394) (3059) (3895) (4731) (5567) (6403) (7230) (8902) (10830)

1010

(470)

0.7

(0.3)

3610 4560 5510 7030 8550 10500 13300 16200 18100 20900 25700 29500

(1055) (1340) (1615) (2062) (2508) (3059) (3895) (4731) (5292) (6118) (7515) (8626)

3800 4800 5800 7400 9000 11000 14000 17000 19000 22000 27000 31000

(1110) (1410) (1700) (2170) (2640) (3220) (4100) (4980) (5570) (6440) (7910) (9080)

1010

(470)

0.7

(0.3)

950

(450)

1.1

(0.5)

950

(450)

1.1

(0.5)

900

(430)

1.5

(0.7)

900

(430)

1.5

(0.7)

2020

(950)

1.3

(0.6)

2020

(950)

1.3

(0.6)

1910

(900)

1.4

(0.6)

1910

(900)

1.4

(0.6)

1800

(850)

2.0

(1.2)

1800

(850)

2.0

(1.2)

2860

(1350)

3.0

(1.4)

2860

(1350)

3.0

(1.4)

2700

(1270)

4.0

(1.8)

2700

(1270)

4.0

(1.8)

3810

(1800)

3.9

(1.8)

3810

(1800)

3.9

(1.8)

60Hz

3600

(1700)

(2.4)

3600

(1700)

(2.4)

(2120)

3.3

(2120)

3.3

4500

6.5

(3.0)

4500

6.5

(3.0)

5400

(2550)

7.8

(3.5)

5400

(2550)

7.8

(3.5)

Low Temperature Models - Capacity @ 4 F.P.I. *

Low Temp. 4 FPI Models 103V 104V 105V 206V 208V 209V 312V 315V 416V 419V 523V 627V Number Of Fans 1 1 1 2 2 2 3 3 4 4 5 6

Capacity

BTUH

(WATTS)

Air Flow CFM (L/S) Refrigerant **

Charge

Capacities rated using 10°F (5.6°C) TD & 100°F (38°C) liquid temperature. Capacities at other TD within a range of 8 to 15 °F (4.4 to 8.3°C) are directly proportional to TD, or use formula: Capacity = Rated capacity ÷ 10 x TD. For capacities at TD outside of range 8 to 15 °F (4.4 to 8.3°C), or liquid temperature lower than 75°F (24°), consult factory . Capacities for R407A and R407C are based on mean temperature. Mean temperature is the average temperature between the saturated suction temperature and the temperature feeding the evaporator. For dew point ratings, consult factory.

* CAPACITY CORRECTION FACTORS FOR LOW TEMPERATURE UNITS

SATURATED SUCTION

TEMPERATURE °F (°C)0 (-17.8)

NO CORRECTION FACTOR REQUIRED FOR MEDIUM TEMP. UNITS

Evap

Temp.

-20°F

(-29°C)

R407A

FACTOR 1.06 1.03 1.0 0.92 0.85

R407A

R404A

R507

LB. (KG)

2850 3900 4750 6080 7410 8840 11400 14300 15200 18100 21900 25700

(836) (1140) (1397) (1786) (2176) (2584) (3344) (4171) (4456) (5292) (6403) (7515)

3000 4100 5000 6400 7800 9300 12000 15000 16000 19000 23000 27000

(880) (1200) (1470) (1880) (2290) (2720) (3520) (4390) (4690) (5570) (6740) (7910)

1070

(510)

(0.3)

0.7

-10

(23.3)

1010

(480)

1.1

(0.5)

(450)

-20

(-28.9)

950

1.5

(0.7)

2140

(1010)

(0.6)

-30

(-34.4)

1.3

-40

(-40)

2020

(950)

1.4

(0.6)

1910

(900)

2.0

(1.2)

3030

(1430)

3.0

(1.4)

** REFRIGERANT CHARGE CONVERSION FACTORS

R407C R404A

0.99 0.92 0.93 1.02 1.03

2860

(1350)

4.0

(1.8)

4040

(1910)

3.9

(1.8)

R507

3810

(1800)

3.3

(2.4)

R22

4770

(2250)

R134a

6.5

(3.0)

5720

(2700)

7.8

(3.5)

Page 5

ELECTRICAL DATA

23/12/16

T30-TPLP-PDI-11

- 5 -

TPLP

MODEL FPI

104MAS1 106MAS1 1 1/15 1.0 100 1.3 15 1/15 1.0 60 1.3 15 107MAS1 1 1/15 1.0 100 1.3 15 1/15 1.0 60 1.3 15 209MAS1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 211MAS1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 214MAS1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 317MAS1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 320MAS1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 423MAS1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 426MAS1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 532MAS1 5 1/15 5.0 500 5.3 15 1/15 5.0 300 5.3 15 639MAS1 6 1/15 6.0 600 6.3 15 1/15 6.0 360 6.3 15

QTY.

1 1/15 1.0 100 1.3 15 1/15 1.0 60 1.3 15

115/1/60 - AIR DEFROST MODELS

FAN MOTORS

PSC MOTORS EC MOTORS

FLA

TOTAL

WATTS

MIN. CIRC.

AMPACITY (A)

MAX. FUSE

(AMPS)

FLA

TOTAL

WATTS

AMPACITY (A)

60Hz

MIN. CIRC.

ELECTRICAL DATA

208-230/1/60 - AIR DEFROST MODELS

MAX. FUSE

(AMPS)

FAN MOTORS

MODEL FPI

104MAS2 106MAS2 1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.8 15 107MAS2 1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.8 15 209MAS2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 211MAS2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 214MAS2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 317MAS2 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 320MAS2 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 423MAS2 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 426MAS2 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 532MAS2 5 1/15 2.5 500 2.6 15 1/15 3.0 300 3.2 15 639MAS2 6 1/15 3.0 600 3.1 15 1/15 3.6 360 3.8 15

QTY.

1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.8 15

FLA

TOTAL

PSC MOTORS EC MOTORS

WATTS

MIN. CIRC.

AMPACITY (A)

MAX. FUSE

(AMPS)

FLA

TOTAL

WATTS

MIN. CIRC.

AMPACITY (A)

MAX. FUSE

(AMPS)

ELECTRICAL DATA

460/1/60 - AIR DEFROST MODELS

FAN MOTORS

MODEL FPI

209MAS4 211MAS4 2 1/15 0.8 200 0.9 15 214MAS4 2 1/15 0.8 200 0.9 15 317MAS4 3 1/15 1.2 300 1.3 15 320MAS4 3 1/15 1.2 300 1.3 15 423MAS4 4 1/15 1.6 400 1.7 15 426MAS4 4 1/15 1.6 400 1.7 15 532MAS4 5 1/15 2.0 500 2.1 15 639MAS4 6 1/15 2.4 600 2.5 15

QUANTITY

2 1/15 0.8 200 0.9 15

FLA

TOTAL

PSC MOTORS

WATTS

MIN. CIRC.

AMPACITY (A)

MAX. FUSE

(AMPS)

Page 6

ELECTRICAL DATA -

23/12/16

T30-TPLP-PDI-11

- 6 -

208-230/1/60 & 208-230/3/60

60HzTPLP

ELECTRIC DEFROST MODELS

FAN MOTORS DEFROST HEATERS

MODEL FPI

104ME* 106ME* 1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.8 15 1060 4.6 5.8 15 3.0 3.8 15 107ME* 1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.8 15 1060 4.6 5.8 15 3.0 3.8 15 209ME* 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15

211ME* 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 214ME* 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 317ME* 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 2730 11.9 14.8 15 7.7 10 15 320ME* 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 2730 11.9 14.8 15 7.7 10 15 423ME* 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 3560 15.5 19.3 20 10 12 15 426ME* 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 3560 15.5 19.3 20 10 12 15 532ME* 5 1/15 2.5 500 2.6 15 1/15 3.0 300 3.2 15 4400 19.1 23.9 25 12 15.1 20 639ME* 6 1/15 3.0 600 3.1 15 1/15 3.6 360 3.8 15 5230 22.7 28.4 30 15 18 20

104LE*

105LE* 1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.75 15 1060 4.6 5.8 15 3.0 3.8 15

106LE* 1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.75 15 1060 4.6 5.8 15 3.0 3.8 15

207LE* 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15

209LE* 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15

211LE* 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15

314LE* 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 2730

317LE* 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 2730 11.9 14.8 15 7.7 10 419LE* 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 3560 15.5 19.3 20 10 12 15 422LE* 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 3560 15.5 19.3 20 10 12 15 527LE* 5 1/15 2.5 500 2.6 15 1/15 3.0 300 3.2 15 4400 19.1 23.9 25 12 15.1 20 631LE* 6 1/15 3.0 600 3.1 15 1/15 3.6 360 3.8 15 5230 22.7 28.4 30 15 18 20 103VE* 104VE* 1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.75 15 1060 4.6 5.8 15 3.0 3.8 15 105VE* 1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.75 15 1060 4.6 5.8 15 3.0 3.8 15 206VE* 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 208VE* 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 209VE* 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 312VE* 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 2730 11.9 14.8 15 7.7 10 15 315VE* 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 2730 11.9 14.8 15 7.7 10 15 416VE* 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 3560 15.5 19.3 20 10 12 15 419VE* 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 3560 15.5 19.3 20 10 12 15 523VE* 5 1/15 2.5 500 2.6 15 1/15 3.0 300 3.2 15 4400 19.1 23.9 25 12 15.1 20 627VE* 6 1/15 3.0 600 3.1 15 1/15 3.6 360 3.8 15 5230 22.7 28.4 30 15 18 20

* = S2 or T3. Refer to Nomenclature for details

QTY.

1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.8 15 1060 4.6 5.8 15 3.0 3.8 15

1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.75 15 1060 4.6 5.8 15 3.0 3.8 15

PSC MOTORS EC MOTORS

FLA

TOTAL

WATTS

MCA

(A)

MAX.

FUSE

(AMPS)

FLA

TOTAL

WATTS

MCA

(A)

MAX. FUSE

(AMPS)

TOTAL

WATTS

208-230/1/60 208-230/3/60

MCA

(A)

MAX. FUSE

(AMPS)

TOTAL

AMPS

MCA

(A)

TOTAL

AMPS

11.9 14.8 15 7.7 10 15

(AMPS)

MAX.

FUSE

Page 7

ELECTRICAL DATA - 460/1/60

23/12/16

T30-TPLP-PDI-11

- 7 -

TPLP

MODEL FPI

209MES4 211MES4 2 1/15 0.8 200 0.9 15 1890 4.1 5.1 15 214MES4 2 1/15 0.8 200 0.9 15 317MES4 3 1/15 1.2 300 1.3 15 320MES4 3 1/15 1.2 300 1.3 15 423MES4 4 1/15 1.6 400 1.7 15 426MES4 4 1/15 1.6 400 1.7 15 532MES4 5 1/15 2.0 500 2.1 15 4400 9.6 12.0 15 639MES4 6 1/15 2.4 600 2.5 15 5230 11.4 14.2 15

207LES4 209LES4 2 1/15 0.8 200 0.9 15 1890 4.1 5.1 15 211LES4 2 1/15 0.8 200 0.9 15 314LES4 3 1/15 1.2 300 1.3 15 317LES4 3 1/15 1.2 300 1.3 15 419LES4 4 1/15 1.6 400 1.7 15 422LES4 4 1/15 1.6 400 1.7 15 527LES4 5 1/15 2.0 500 2.1 15 4400 9.6 12.0 15 631LES4 6 1/15 2.4 600 2.5 15 5230 11.4 14.2 15

206VES4 208VES4 2 1/15 0.8 200 0.9 15 1890 4.1 5.1 15 209VES4 2 1/15 0.8 200 0.9 15 312VES4 3 1/15 1.2 300 1.3 15 315VES4 3 1/15 1.2 300 1.3 15 416VES4 4 1/15 1.6 400 1.7 15 419VES4 4 1/15 1.6 400 1.7 15 523VES4 5 1/15 2.0 500 2.1 15 4400 9.6 12.0 15 627VES4 6 1/15 2.4 600 2.5 15 5230 11.4 14.2 15

QTY.

2 1/15 0.8 200 0.9 15

ELECTRIC DEFROST MODELS

FAN MOTORS DEFROST HEATERS

FLA

TOTAL

PSC MOTORS

WATTS

MCA

(A)

MAX. FUSE

(AMPS)

TOTAL

WATTS

1890 4.1 5.1 15

1890 4.1 5.1 15 2730 5.9 7.4 15 2730 5.9 7.4 15 3560 7.7 9.7 15 3560 7.7 9.7 15

1890 4.1 5.1 15

1890 4.1 5.1 15 2730 5.9 7.4 15

2730 5.9 7.4 15 3560 7.7 9.7 15 3560 7.7 9.7 15

1890 4.1 5.1 15

1890 4.1 5.1 15 2730 5.9 7.4 15

2730 5.9 7.4 15 3560 7.7 9.7 15 3560 7.7 9.7 15

TOTAL

AMPS

60Hz

MCA

(A)

MAX. FUSE

(AMPS)

Page 8

CONDUCTORS/WIRING

AND NATIONAL CODES.

-TERMINAL BLOCK TERMINAL

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL

-COMPONENT TERMINAL

4). MAY BE FACTORY INSTALLED-MOUNTED AND

3). OVERCURRENT PROTECTION FOR

1). USE COPPER CONDUCTORS ONLY

VALUE SHOWN ON EVAPORATOR NAMEPLATE.

HEATERS MUST NOT EXCEED MAXIMUM

EVAPORATOR FAN MOTORS AND DEFROST

2). USE 75°C WIRE (OR HIGHER)

WIRED ON EVAPORATOR .

NOTES

TERMINALS

OPTIONAL FACTORY OR

1-LP AIR 09/06

BY OTHERS

WIRING BY OTHERS

FACTORY WIRING

WITHOUT DEFROST TIME CLOCK

REQUIREMENTS

REFER TO EVAPORATOR

NAMEPLATE FOR ELECTRICAL

PARAGON # 8145

DEFROST CLOCK OR EQUIVALENT

THERMOSTAT

CIRCUIT

FUSE OR

NOTE #3

BREAKER

SWITCH

PUMP DOWN

(IF USED)

NOTE #4

SPACE

LIQUID LINE

SOLENOID VALVE

NOTE #4

N.C.

WITH DEFROST TIME CLOCK

GND

SOLENOID VALVE

THERMOSTAT

BREAKER NOTE #3

FUSE OR CIRCUIT

SPACE

NOTE #4

IF(N)

2ND FUSE

OMIT

LIQUID LINE

NOTE #4

N.C.

L2(N)

REFER TO EVAPORATOR DATA PLATE FOR MOTOR QUANTITY

GND.

FAN

MTR

FAN MTR

EVAPORATOR

TERMINAL BOARD

FAN MOTOR POWER PLUGS

FAN MTR

FAN

MTR

FAN MTR

GND.

TERMINAL BOARD

REFER TO EVAPORATOR DATA PLATE FOR MOTOR QUANTITY

FAN MOTOR POWER PLUGS

EVAPORATOR

IF(N)

OMIT 2ND

L2(N)

TO MULTIPLE EVAPS

(IF APPLIC)

EVAPORATORS (IF APPLIC)

TO MULTIPLE

FUSE

GND

REQUIREMENTS

REFER TO EVAPORATOR

NAMEPLATE FOR ELECTRICAL

TPLP

23/12/16

T30-TPLP-PDI-11

- 8 -

WIRING DIAGRAM - 115/1/60, 208-230/1/60

STANDARD PSC MOTORS

AIR DEFROST MODELS

PSC

60Hz

Page 9

CONDUCTORS/WIRING

AND NATIONAL CODES.

-TERMINAL BLOCK TERMINAL

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL

-COMPONENT TERMINAL

4). MAY BE FACTORY INSTALLED-MOUNTED AND

3). OVERCURRENT PROTECTION FOR

1). USE COPPER CONDUCTORS ONLY

VALUE SHOWN ON EVAPORATOR NAMEPLATE.

HEATERS MUST NOT EXCEED MAXIMUM

EVAPORATOR FAN MOTORS AND DEFROST

2). USE 75°C WIRE (OR HIGHER)

WIRED ON EVAPORATOR .

NOTES

TERMINALS

OPTIONAL FACTORY OR

6-LP 460 AIR 09/06

BY OTHERS

WIRING BY OTHERS

FACTORY WIRING

WITHOUT DEFROST TIME CLOCK

PARAGON # 8145

DEFROST CLOCK OR EQUIVALENT

THERMOSTAT

CIRCUIT

FUSE OR

NOTE #3

BREAKER

SWITCH

PUMP DOWN

(IF USED)

NOTE #4

SPACE

LIQUID LINE

SOLENOID VALVE

NOTE #4

N.C.

WITH DEFROST TIME CLOCK

380/400-1-50Hz

CONTROL VOLTAGE

GND

IF(N)

2ND FUSE

OMIT

REFER TO EVAPORATOR DATA PLATE FOR MOTOR QUANTITY

GND.

FAN MTR

EVAPORATOR

FAN MOTOR POWER PLUGS

FAN MTR

FAN

MTR

GND.

TERMINAL BOARD

REFER TO EVAPORATOR DATA PLATE FOR MOTOR QUANTITY

FAN MOTOR POWER PLUGS

EVAPORATOR

IF(N)

OMIT 2ND

TO MULTIPLE

EVAPORATORS (IF APPLIC)

TO MULTIPLE

FUSE

GND

L2(N)

460-1-60 Hz

TERMINAL BOARD

THERMOSTAT

NOTE #4

N.C.

SOLENOID VALVE

SPACE

LIQUID LINE NOTE #4

GND

L2(N)

460-1-60 Hz

380/400-1-50Hz

CONTROL VOLTAGE

NOTE #3

CIRCUIT

BREAKER

FUSE OR

TPLP

23/12/16

T30-TPLP-PDI-11

- 9 -

WIRING DIAGRAM - 460/1/60

STANDARD PSC MOTORS

AIR DEFROST MODELS

PSC

60Hz

Page 10

WARNING

EVAP FIELD MODIFICATION

MUST BE MADE

REFER TO EVAPORATOR

COMPR INTERLOCK

FOR ALL MODELS WITHOUT DEFROST HEATER CONTACTOR

THERMOSTAT

NOTE #4

EVAPORATOR FAN MOTORS AND DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 75°C WIRE (OR HIGHER)

FAN

MTR

DEFROST TERMINATION

CONTROL

(10.0A MAX.)

& FAN DELAY

FD-FAN DELAY

DT-DEFROST TERM

GND.

(IF USED)

SWITCH

OR EQUIVALENT

PUMP DOWN

SPACE

(IF USED)

DEFROST CLOCK PARAGON # 8145

EVAPORATOR

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

2-LP ED 12/07

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

DATA PLATE FOR MOTOR QUANTITY

EVAPORATOR

REFER TO

POWER PLUGS

FAN MOTOR

NOTE #4

SOL VALVE

L2L1

N.C.

LIQUID LINE

GND

NAMEPLATE FOR ELECTRICAL

REQUIREMENTS

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

DEFROST HEATERS

CIRCUIT BREAKER

FUSE OR

USING MAXIMUM 15A HEATER OVERCURRENT PROTECTION

15A

FAN

MTR

FAN MTR

ORANGE JUMPER

SWITCH

LIMIT

HEATER

(10.0A MAX.)

FROM H2 TO N

INSTALL ORANGE JUMPER (SUPPLIED LOOSE)

N TO H1 AS SHOWN

RELOCATE WHITE WIRE FROM

SEE NOTE:

TPLP

23/12/16

T30-TPLP-PDI-11

- 10 -

WIRING DIAGRAM - 208-230/1/60

STANDARD PSC MOTORS

PSC

60Hz

ELECTRIC DEFROST MODELS - SINGLE EVAPORATOR 10A MAX.

Page 11

COMPR INTERLOCK

FOR ALL MODELS USING DEFROST HEATER CONTACTOR

THERMOSTAT

NOTE #4

EVAPORATOR FAN MOTORS AND DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 75°C WIRE (OR HIGHER)

(IF USED)

SWITCH

OR EQUIVALENT

PUMP DOWN

SPACE

(IF USED)

DEFROST CLOCK PARAGON # 8145

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

3-LP ED CONTACTOR SINGLE 12/07

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

NOTE #4

SOL VALVE

N.C.

LIQUID LINE

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

CIRCUIT BREAKER NOTE #3

FUSE OR

CONTACTOR

DEFROST HEATER

NOTE #3

BREAKER

FUSE OR CIRCUIT

GND

L2L1

(10.0A MAX.)

REFER TO

POWER PLUGS

MOTOR QUANTITY

DATA PLATE FOR

EVAPORATOR

FAN MOTOR

621

DEFROST TERMINATION

FD-FAN DELAY

DT-DEFROST TERM

FAN MTR

GND.

FAN MTRMTR

FAN

(10.0A MAX.)

CONTROL

& FAN DELAY

LIMIT

SWITCH

HEATER

EVAPORATOR

DEFROST HEATERS

REFER TO EVAPORATOR NAMEPLATE

FOR ELECTRICAL REQUIREMENTS

TPLP

23/12/16

T30-TPLP-PDI-11

- 11 -

ELECTRIC DEFROST MODELS - SINGLE EVAPORATOR

WIRING DIAGRAM - 208-230/1/60

STANDARD PSC MOTORS

PSC

60Hz

Page 12

COMPR INTERLOCK

FOR ALL MODELS USING 3 PHASE DEFROST HEATER CONTACTOR

THERMOSTAT

NOTE #4

EVAPORATOR FAN MOTORS AND DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 75°C WIRE (OR HIGHER)

(IF USED)

SWITCH

OR EQUIVALENT

PUMP DOWN

SPACE

(IF USED)

DEFROST CLOCK

PARAGON # 8145

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

3A-LP ED 3ph.CONTACTOR SINGLE 12/07

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

NOTE #4

SOL VALVE

N.C.

LIQUID LINE

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

CIRCUIT BREAKER NOTE #3

FUSE OR

CONTACTOR

DEFROST HEATER

NOTE #3

BREAKER

FUSE OR CIRCUIT

GND

L2L1

DEFROST HEATERS

H2 H3

DATA PLATE FOR MOTOR QUANTITY

12 6

CONTROL

(10.0A MAX.)

& FAN DELAY

DT-DEFROST TERM

DEFROST TERMINATION

FD-FAN DELAY

MTR

FAN

MTR

FAN

GND.

SWITCH

(10.0A MAX.)

MTR

FAN

FAN MOTOR

REFER TO EVAPORATOR

POWER PLUGS

HEATER

LIMIT

EVAPORATOR

REFER TO EVAPORATOR NAMEPLATE

FOR ELECTRICAL REQUIREMENTS

TPLP

23/12/16

T30-TPLP-PDI-11

- 12 -

ELECTRIC DEFROST MODELS - SINGLE EVAPORATOR

WIRING DIAGRAM - 208-230/3/60

STANDARD PSC MOTORS

PSC

60Hz

Page 13

WIRING DIAGRAM - 460/1/60

REFER TO EVAPORATOR NAMEPLATE

FOR ELECTRICAL REQUIREMENTS

COMPR INTERLOCK

FOR ALL 460V MODELS USING DEFROST HEATER AND FAN CONTACTORS

THERMOSTAT

NOTE #4

EVAPORATOR FAN MOTORS AND

DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 75°C WIRE (OR HIGHER)

MTR

FANFAN

MTR

FAN

MTR

GND.

(IF USED)

SWITCH

OR EQUIVALENT

PUMP DOWN

SPACE

(IF USED)

BREAKER

NOTE #3

CIRCUIT

FUSE OR

DEFROST CLOCK PARAGON # 8145

EVAPORATOR

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

7-LP ED CONTACTOR SINGLE 12/07

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

DATA PLATE FOR MOTOR QUANTITY

EVAPORTOR

REFER TO

POWER PLUGS

FAN MOTOR

NOTE #4

SOL VALVE

L2L1

N.C.

LIQUID LINE

GND

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

CIRCUIT

BREAKER

NOTE #3

FUSE OR

GND

L2(N)

CONTACTOR

DEFROST HEATER

EVAP FAN

CONTACTOR

COIL DEFROST HEATERS

H1 H2

DEFROST TERMINATION

CONTROL

& FAN DELAY

(10.0A MAX.)

FD-FAN DELAY

DT-DEFROST TERM

(10.0A MAX.)

LIMIT

SWITCH

HEATER

23/12/16

T30-TPLP-PDI-11

- 13 -

TPLP

STANDARD PSC MOTORS

ELECTRIC DEFROST MODELS - SINGLE EVAPORATOR

PSC

60Hz

Page 14

MUST BE MADE

EVAP#2 FIELD MODIFICATION

WARNING

COMPR INTERLOCK

FOR ALL MODELS USING DEFROST HEATER CONTACTOR

THERMOSTAT

NOTE #4

EVAPORATOR FAN MOTORS AND DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 75°C WIRE (OR HIGHER)

MTR

FANFAN

MTR

FAN MTR

DEFROST TERMINATION

CONTROL

(10.0A MAX.)

& FAN DELAY

FD-FAN DELAY

DT-DEFROST TERM

GND.

(IF USED)

SWITCH

OR EQUIVALENT

PUMP DOWN

SPACE

(IF USED)

BREAKER

NOTE #3

CIRCUIT

FUSE OR

DEFROST CLOCK

PARAGON # 8145

EVAPORATOR

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

4-LP ED CONTACTOR MULTI 12/07

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

DATA PLATE FOR MOTOR QUANTITY

EVAPORATOR

REFER TO

POWER PLUGS

FAN MOTOR

NOTE #4

SOL VALVE

N.C.

LIQUID LINE

GND

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

DEFROST HEATERS

CIRCUIT BREAKER NOTE #3

FUSE OR

DEFROST HEATER

CONTACTOR

EVAPORATOR

MTR

FAN

MTR

FANFAN

MTR

FAN MOTOR POWER PLUGS

EVAPORATOR

MOTOR QUANTITY

DATA PLATE FOR

REFER TO

GND.

DEFROST TERMINATION

DT-DEFROST TERM FD-FAN DELAY

(10.0A MAX.)

CONTROL

& FAN DELAY

DEFROST HEATERS

* Remove & Insulate

* Fan delay not used on second evap / use fan contactor if total fan amps exceeds 10A

PRIMARY

SECONDARY

FUSE OR

BREAKER NOTE #3

CIRCUIT

H1NH2

H1N

LIMIT

(10.0A MAX.)

SWITCH

HEATER

LIMIT

(10.0A MAX.)

SWITCH

HEATER

REFER TO EVAPORATOR NAMEPLATE

FOR ELECTRICAL REQUIREMENTS

RELOCATE WHITE WIRE FROM

N AS SHOWN

SEE NOTE:

REMOVE AND INSULATE

AS SHOWN

TPLP

23/12/16

T30-TPLP-PDI-11

- 14 -

ELECTRIC DEFROST MODELS - MULTIPLE EVAPORATORS

WIRING DIAGRAM - 208-230/1/60

STANDARD PSC MOTORS

PSC

60Hz

Page 15

WARNING

EVAP#2 FIELD MODIFI-

CATION MUST BE MADE

COMPR INTERLOCK

FOR ALL 460V MODELS USING DEFROST HEATER AND FAN CONTACTORS

THERMOSTAT

NOTE #4

EVAPORATOR FAN MOTORS AND DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 75°C WIRE (OR HIGHER)

MTR

FANFAN

MTR

FAN

MTR

GND.

(IF USED)

SWITCH

OR EQUIVALENT

PUMP DOWN

SPACE

(IF USED)

BREAKER

NOTE #3

CIRCUIT

FUSE OR

DEFROST CLOCK PARAGON # 8145

EVAPORATOR

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

8-LP 460v ED CONTACTOR MULTI 09/06

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

DATA PLATE FOR MOTOR QUANTITY

EVAPORATOR

REFER TO

POWER PLUGS

FAN MOTOR

NOTE #4

SOL VALVE

N.C.

LIQUID LINE

GND

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

CIRCUIT BREAKER

NOTE #3

FUSE OR

GND

L2(N)

CONTACTOR

DEFROST HEATER

EVAP FAN

CONTACTOR

MTR

FAN

MTR

FAN

GND.

EVAPORATOR

REFER TO EVAPORATOR

MOTOR QUANTITY

DATA PLATE FOR

MTR

FAN

POWER PLUGS

FAN MOTOR

NOTE #3

FUSE OR CIRCUIT BREAKER

PRIMARY

SECONDARY

* Note: Fan Delay not used on second evap

DEFROST HEATERS

H1 H2

DEFROST TERMINATION

DT-DEFROST TERM FD-FAN DELAY

CONTROL

(10.0A MAX.)

& FAN DELAY

DEFROST TERMINATION

DT-DEFROST TERM FD-FAN DELAY

CONTROL

(10.0A MAX.)

& FAN DELAY

DEFROST HEATERS

H1 H2

HEATER SWITCH

LIMIT

(10.0A MAX.)

LIMIT

SWITCH

HEATER

N AS SHOWN

RELOCATE WHITE WIRE FROM

REFER TO EVAPORATOR NAMEPLATE

FOR ELECTRICAL REQUIREMENTS

TPLP

23/12/16

T30-TPLP-PDI-11

- 15 -

ELECTRIC DEFROST MODELS - MULTIPLE EVAPORATORS

WIRING DIAGRAM - 460/1/60

STANDARD PSC MOTORS

PSC

60Hz

Page 16

TPLP

SmartSpeed

Evaporators

Energy Consumption (Watt

EVAP w/ PSC

EVAP with SmartSpeed

REFRIGERATION = FULL SPEED = 60W PER MOTOR

OFF CYCLE = LOW SPEED = 13W PER MOTOR 40 % EXTRA ENERGY SAVINGS vs. FIXED SPEED EC MOTOR ON EVAPORATOR

10 % EXTRA ENERGY SAVINGS ON COMPRESSOR WHEN USING SMARTSPEED EVAPORATOR

DESIGN HIGHLIGHTS

NO COMPLEX CONTROLS, NO COST ADDER, SIMPLE TO UNDERSTAND

PATENT

PENDING

23/12/16

T30-TPLP-PDI-11

- 16 -

US Patent No.

8,635,883

DESIGN FEATURES

• Standard on all EC Motors

ECM

60Hz

• Refrigeration mode – EC motor operates at full speed.

•O󰀨Cyclemode–ECmotoroperatesatreducedspeed.

• NO special controls required.

Consumption 60 W per motor

Consumption 13 W per motor.

•Energysavingbenetonmotorandcompressorwattageconsumption:

20000

ENERGY CONSUMPTION COMPA RISON:

ADDITIONAL ENERGY SAVINGS WHEN USING SMARTSPEED EVAPS

-Hours)

18000

16000

14000

12000

10000

8000

6000

with PSC vs ECM vs SmartSpeed Evaporator Fan Motors

Compressor w/ PSC Compressor w/ ECM

Compressor w/ SmartSpeed

4000

2000

0 50 100 150 200 250 300 350 400 450 500

Time (minutes)

Note: Data collected on a typical freezer application with a 3HP low temp condensing unit and a 4 fan TPLP evaporator

EVAP w/ ECM

INSTALLATION NOTES

EC motors are factory wired for SmartSpeed operation on evaporators equipped with a factory installed thermostat.

For SmartSpeed operation on Evaporators without a factory installed thermostat,

aeldwiredSPDTtypethermostatisrequired.

Page 17

TPLP

23/12/16

T30-TPLP-PDI-11

- 17 -

WIRING DIAGRAM - 115/1/60, 208-230/1/60

OPTIONAL EC MOTORS with

AIR DEFROST MODELS

ECM

60Hz

Page 18

TPLP

23/12/16

T30-TPLP-PDI-11

- 18 -

WIRING DIAGRAM - 208-230/1/60

OPTIONAL EC MOTORS with

ELECTRIC DEFROST MODELS

ECM

60Hz

Page 19

TPLP

23/12/16

T30-TPLP-PDI-11

- 19 -

ELECTRIC DEFROST MODELS - MULTIPLE EVAPORATORS

WIRING DIAGRAM - 208-230/1/60

OPTIONAL EC MOTORS with

ECM

60Hz

Page 20

TPLP

23/12/16

T30-TPLP-PDI-11

- 20 -

SHIPPING WEIGHTS

60Hz

Air Defrost Models

MODEL

NUMBER

104MA 45 (20) 106MA 47 (21) 107MA 49 (22) 209MA 70 (32) 211MA 74 (33) 214MA 78 (35) 317MA 101 (46) 320MA 107 (48) 423MA 117 (53) 426MA 135 (61) 532MA 163 (74) 639MA 192 (87)

SHIPPING WEIGHT LB. (kg)

Electric Defrost Models

MODEL NUMBER

104ME 104LE 103VE 49 (22) 106ME 105LE 104VE 51 (23) 107ME 106LE 105VE 53 (24) 209ME 207LE 206VE 76 (34) 211ME 209LE 208VE 80 (36) 214ME 211LE 209VE 84 (38) 317ME 314LE 312VE 109 (49) 320ME 317LE 315VE 115 (52) 423ME 419LE 416VE 127 (58) 426ME 422LE 419VE 145 (66) 532ME 527LE 523VE 176 (80) 639ME 631LE 627VE 207 (94)

SHIPPING WEIGHT

LB. (kg)

Page 21

.438 SLOTS IN MOUNTING BRACKETS

AIR THROW APPROX 35' IN OPEN SPACE

MINIMUM

11 7/83 1/8

[305][302] [79]

[76]

[403]

15 7/8

[35]

1 3/8

3/4 MPT / 3/4 FLARE DRAIN CONNECTION

4, 5 AND 6 FAN MODELS.

6 1/2

[165]

MTG SLOTS

13 7/16

[341]

(TOP VIEW)

REFRIGERATION CONNECTIONS. SUCTION & LIQUID.

ELECTRICAL CONNECTIONS.

13 7/16

MTG SLOTS

[165]

6 1/26 1/2

TYP

[102]

[341]

1, 2 AND 3 FAN MODELS. (TOP VIEW)

TPLP

23/12/16

T30-TPLP-PDI-11

- 21 -

DIMENSIONAL DATA

60Hz

LIQUID CONNECTION (ID)

SWEAT

R407A

R22

R404A

MODEL

NO. OF

FANS

A B C

IN (mm) IN (mm) IN (mm)

SUCTION

CONNECTION

(ID) SWEAT

104M^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 3/8 3/8 106M^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 3/8 3/8 107M^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 3/8 3/8 209M^ 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 3/8 3/8 211M^ 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 3/8 3/8 214M^ 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 3/8 3/8 317M^ 3 62 1/4 (1581) 49 1/4 (1251) N/A N/A 7/8 3/8 3/8 320M^ 3 62 1/4 (1581) 49 1/4 (1251) N/A N/A 7/8 3/8 3/8

423M^ 4 78 1/4 (1988) 32 5/8 (829) 32 5/8 (829) 1 1/8 3/8 3/8 426M^ 4 78 1/4 (1988) 32 5/8 (829) 32 5/8 (829) 1 1/8 3/8 1/2 532M^ 5 94 1/4 (2394) 32 5/8 (829) 48 5/8 (1235) 1 3/8 1/2 1/2 639M^ 6 110 1/4 (2800) 48 5/8 (1235) 48 5/8 (1235) 1 3/8 1/2 1/2

104L^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 3/8 3/8 105L^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 3/8 3/8 106L^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 3/8 3/8 207L^ 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 3/8 3/8 209L^ 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 3/8 3/8 211L^ 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 3/8 3/8

314L^ 3 62 1/4 (1581) 49 1/4 (1251) N/A N/A 7/8 3/8 3/8 317L^ 3 62 1/4 (1581) 49 1/4 (1251) N/A N/A 1 1/8 3/8 3/8

419L^ 4 78 1/4 (1988) 32 5/8 (829) 32 5/8 (829) 1 1/8 3/8 3/8 422L^ 4 78 1/4 (1988) 32 5/8 (829) 32 5/8 (829) 1 1/8 3/8 3/8 527L^ 5 94 1/4 (2394) 32 5/8 (829) 48 5/8 (1235) 1 3/8 3/8 1/2

631L^ 6 110 1/4 (2800) 48 5/8 (1235) 48 5/8 (1235) 1 3/8 1/2 1/2

^ = A or E. Refer to Nomenclature for details

103V^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 3/8 3/8 104V^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 3/8 3/8 105V^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 3/8 3/8 206V^ 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 3/8 3/8 208V^ 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 3/8 3/8 209V^ 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 3/8 3/8 312V^ 3 62 1/4 (1581) 49 1/4 (1251) N/A N/A 7/8 3/8 3/8 315V^ 3 62 1/4 (1581) 49 1/4 (1251) N/A N/A 1 1/8 3/8 3/8 416V^ 4 78 1/4 (1988) 32 5/8 (829) 32 5/8 (829) 1 1/8 3/8 3/8 419V^ 4 78 1/4 (1988) 32 5/8 (829) 32 5/8 (829) 1 1/8 3/8 3/8 523V^ 5 94 1/4 (2394) 32 5/8 (829) 48 5/8 (1235) 1 3/8 3/8 1/2 627V^ 6 110 1/4 (2800) 48 5/8 (1235) 48 5/8 (1235) 1 3/8 3/8 1/2

Page 22

RECOMMENDED EXPANSION V ALVE

23/12/16

T30-TPLP-PDI-11

- 22 -

TPLP

SPORLAN

MODEL

104M N/A EBQE-AA-*C EBQE-AAA-VC EBQE-AAA-JC 106M L-1/2 EBQE-AA-*C EBQE-AA-VC EBQE-AA-JC 107M L-1/2 EBQE-A-*C EBQE-AA-VC EBQE-AA-JC 209M L-3/4 EBQE-A-*C EBQE-AA-VC EBQE-AA-JC 211M L-1 EBQE-A-*C EBQE-A-VC EBQE-A-JC 214M L-1 EBQE-B-*C EBQE-A-VC EBQE-A-JC 317M L-1 1/2 EBQE-B-*C EBQE-A-VC EBQE-A-JC 320M L-1 1/2 EBQE-B-*C EBQE-B-VC EBQE-A-JC 423M L-2 EBQE-B-*C EBQE-B-VC EBQE-A-JC 426M L-2 EBQE-C-*C EBQE-B-VC EBQE-B-JC 532M L-2 1/2 EBQE-C-*C EBQE-B-VC EBQE-B-JC 639M G-3 EBQE-C-*C EBQE-C-VC EBQE-C-JC

* Varies with refrigerant: S = R404A, P = R507

ALCO

MODEL

104M N/A HFESC 1/4 SC HFESC 1/2 HC HFESC 1/2 MC 106M L-1/2 HFESC 1/2 SC HFESC 1/2 HC HFESC 3/4 MC 107M L-1/2 HFESC 1/2 SC HFESC 1/2 HC HFESC 3/4 MC 209M L-3/4 HFESC 1 SC HFESC 1 HC HFESC 3/4 MC

211M L-1 HFESC 1 SC HFESC 1 HC HFESC 1 MC 214M L-1 HFESC 1-1/4 SC HFESC 1-1/2 HC HFESC 1 MC 317M L-1 1/2 HFESC 1-1/2 SC HFESC 1-1/2 HC HFESC 1-1/2 MC 320M L-1 1/2 HFESC 1-1/2 SC HFESC 2 HC HFESC 1-3/4 MC 423M L-2 HFESC 2 SC HFESC 2 HC HFESC 1-3/4 MC 426M L-2 HFESC 2 SC HFESC 2-1/2 HC HFESC 2-1/2 MC 532M L-2 1/2 HFESC 3-1/2 SC HFESC 2-1/2 HC HFESC 2-1/2 MC 639M G-3 HFESC 3-1/2 SC HFESC 3 HC HFESC 4 MC

DANFOSS

MODEL

104M N/A TUAE-R404A-4-N TUAE-R22-4-N TUAE-R134a-4-N

106M L-1/2 TUAE-R404A-5-N TUAE-R22-5-N TUAE-R134a-5-N

107M L-1/2 TUAE-R404A-6-N TUAE-R22-5-N TUAE-R134a-5-N

209M L-3/4 TUAE-R404A-7-N TUAE-R22-6-N TUAE-R134a-6-N

211M L-1 TUAE-R404A-7-N TUAE-R22-6-N TUAE-R134a-6-N

214M L-1 TUAE-R404A-8-N TUAE-R22-7-N TUAE-R134a-7-N

317M L-1 1/2 TUAE-R404A-8-N TUAE-R22-8-N TUAE-R134a-8-N

320M L-1 1/2 TUAE-R404A-9-N TUAE-R22-8-N TUAE-R134a-8-N

423M L-2 TUAE-R404A-9-N TUAE-R22-8-N TUAE-R134a-9-N

426M L-2 TCAE-R404A-TC1-N TUAE-R22-9-N TUAE-R134a-9-N

532M L-2 1/2 TCAE-R404A-TC2-N TUAE-R22-9-N TCAE-R134a-TC1-N

639M G-3 TCAE-R404A-TC3-N TCAE-R22-TC1-N TCAE-R134a-TC2-N

† If using 407C, superheat setting must be adjusted by turning 1 - 1.5 turns clockwise.

FACTORY

INSTALLED

NOZZLE

FACTORY

INSTALLED

NOZZLE

FACTORY

INSTALLED

NOZZLE

SELECTIONS - MEDIUM TEMP. MODELS

R404A

R507

R404A

R507

R404A

R507

R407A

R407C

R22

R407A

R407C

R22

R407A

R407C

R22

R134a

†

R134a

If correct nozzle is not

available, the proper

orice size can be

drilled in the eld using

the following chart

NOZZLE

ORIFICE

No.

1/2 .070 3/4 .086

1 .0995

1-1/2 .120

2 .1406

2-1/2 .157

3 .172 4 .199 5 .211 6 .242 8 .266

10 .281

DRILL

SIZE

IN.

60Hz

Above selections based on:

1) 100°F (38°C) vapor free liquid entering expansion valve

2) 110°F (43°C) Condensing temperature

3) 8 -12°F (4.4 -6.7°C) evaporator TD

Page 23

TPLP

23/12/16

T30-TPLP-PDI-11

- 23 -

RECOMMENDED EXPANSION V ALVE

SELECTIONS - LOW TEMP. MODELS

60Hz

SPORLAN -

MODEL

104L L-1/2 EBQE-AAA-VC EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 105L L-3/4 EBQE-AA-VC EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 106L L-1 EBQE-AA-VC EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 207L L-1 EBQE-AA-VC EBQE-AA-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 209L L-1-1/2 EBQE-AA-VC EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40

211L L-2 EBQE-A-VC EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 EBQE-B-VZP40 314L L-2 EBQE-A-VC EBQE-A-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 317L L-3 EBQE-A-VC EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 419L L-3 EBQE-A-VC EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 422L G-4 EBQE-B-VC EBQE-B-VZP40 EBQE-B-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 527L G-4 EBQE-B-VC EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 631L G-5 EBQE-C-VC EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 103V L-1/2 EBQE-AAA-VC EBQE-AAA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 104V L-3/4 EBQE-AAA-VC EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 105V L-1 EBQE-AA-VC EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 206V L-1 EBQE-AA-VC EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-A-VZP40 208V L-1 1/2 EBQE-AA-VC EBQE-AA-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 209V L-2 EBQE-A-VC EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 312V L-2 EBQE-A-VC EBQE-A-VZP40 EBQE-A-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 315V L-2 1/2 EBQE-A-VC EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 416V L-2 1/2 EBQE-A-VC EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 419V G-3 EBQE-A-VC EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 523V G-4 EBQE-B-VC EBQE-B-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 627V G-5 EBQE-B-VC EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40

FACTOR Y INSTALLED

R407A

NOZZLE

0° F (-18° C) EVAP. -10° F (-23° C) EVAP. -20° F (-29° C) EVAP. -30° F (-34° C) EVAP. -40° F (-40° C) EVAP.

SPORLAN -

MODEL

104L L-1/2 EBQE-AA-SC EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP 105L L-3/4 EBQE-AA-SC EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP 106L L-1 EBQE-AA-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 207L L-1 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 209L 1-1/2 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 211L L-2 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 314L L-2 EBQE-B-SC EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP 317L L-3 EBQE-B-SC EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP 419L L-3 EBQE-B-SC EBQE-B-SZP EBQE-C-SZP EBQE-C-SZP EBQE-C-SZP 422L G-4 EBQE-C-SC EBQE-C-SZP EBQE-C-SZP EBQE-C-SZP EBQE-C-SZP 527L G-4 EBQE-C-SC EBQE-C-SZP EBQE-C-SZP EBSE-6-SZP EBSE-6-SZP 631L G-5 EBSE-6-SC EBSE-6-SZP EBSE-6-SZP EBSE-6-SZP EBSE-6-SZP 103V L-1/2 EBQE-AA-SC EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP 104V L-3/4 EBQE-AA-SC EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP 105V L-1 EBQE-AA-SC EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP 206V L-1 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 208V L-1 1/2 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 209V L-2 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 312V L-2 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-B-SZP EBQE-B-SZP 315V L-2 1/2 EBQE-B-SC EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP 416V L-2 1/2 EBQE-B-SC EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP 419V G-3 EBQE-B-SC EBQE-B-SZP EBQE-C-SZP EBQE-C-SZP EBQE-C-SZP 523V G-4 EBQE-C-SC EBQE-C-SZP EBQE-C-SZP EBQE-C-SZP EBQE-C-SZP 627V G-5 EBQE-C-SC EBQE-C-SZP EBQE-C-SZP EBSE-6-SZP EBSE-6-SZP

FACTOR Y INSTALLED

R404A

NOZZLE

0° F (-18° C) EVAP. -10° F (-23° C) EVAP. -20° F (-29° C) EVAP. -30° F (-34° C) EVAP. -40° F (-40° C) EVAP.

Above selections based on:

1) 100°F (38°C) vapor free liquid entering expansion valve

2) 110°F (43°C) Condensing temperature

3) 8 -12°F (4.4 -6.7°C) evaporator TD

Page 24

TPLP

23/12/16

T30-TPLP-PDI-11

- 24 -

INSTALLATION INSTRUCTIONS

60Hz

INSTALLATION

The installation and start-up of evaporators should only

beperformedbyqualiedrefrigerationmechanics.

This equipment should be installed in accordance with all applicable codes, ordinances and local by-laws.

INSPECTION

Inspect all equipment before unpacking for visible signs of damage or loss. Check shipping list against material

received to ensure shipment is complete. IMPORTANT: Remember, you, the consignee, must

make any claim necessary against the transportation company. Shipping damage or missing parts, when discovered at the outset, will prevent later unnecessary and costly delays.

If damage or loss during transport is evident, make claim to carrier, as this will be their responsibility, not the manufacturer’s.

Should carton be damaged, but damage to equipment is

notobvious,aclaimshouldbeledfor“concealed

damage” with the carrier. IMPORTANT: The electrical characteristics of the unit

should be checked at this time to make sure they correspond to those ordered and to electrical power available at the job site.

Save all shipping papers, tags and instruction sheets for reference by installer and owner.

APPLICATION

TPLP evaporators are designed for walker-in cooler and freezer applications used with a wide range of refrigerants. For room temperatures above 35°F (2°C) AND evaporating temperatures above 26°F (-3°C), positive defrosting means (electric) may not be required, otherwise, electric defrost defrost models should be used. Electric defrost models come with defrost termination and fan delay as standard to control the defrost cycle termination and fan delay, while defrost initiation means (e.g. defrost timer) is not included.

The coil must not be exposed to any abnormal atmospheric or acidic environments. This may result in corrosion to the cabinet and possible coil failure (leaks). (Consult manufacturer for optional baked on phenolic

protective coatings).

LOCATION

The unit location in the room should be selected to ensure uniform air distribution throughout the entire space to be refrigerated. Be sure that the product does not obstruct the free circulation of air. Allow a minimum of 24” clearance at each end. Do not locate evaporators over doors. Consideration should be given to the coil location in order to minimize the piping run length to the

condensingunitandoordrain.

EXPANSION VALVE (TXV) PRE-SELECTED

Locate the expansion valve bulb on a horizontal length of suction line preferably 3 to 6 inches from the suction header. Locate the bulb at 4 or 8 clock position and insulate with a waterproof type of insulation. Clamp the bulb to ensure 100% contact of the bulb with the suction line.

After following the manufacturer’s installation instructions and after the room has reached the desired temperature the valve superheat should be checked.

Thiswillconrmthattheevaporatorisoperating properlyandperformingtomaximume󰀩ciency.The

superheat should be around 6 (3.3°C) to 8°F (4.4°C) for a 10 to 12°F T.D (5.6 to 6.7°C). Too high or low a super

heat will result in unsatisfactory system performance and possible compressor problems.

MOUNTING

Refer to dimensional drawing for recommended mounting arrangements. Ensure adequate clearance is provided behind the coil as well as each end. The

evaporatorsmaybemountedushwithceilingwith

bolts, or hanging down with rod hangers. When using rod hangers, allow adequate space between the top of the unit and the ceiling for cleaning to comply with NSF Standard 7.

Ensure that the ceiling is level since the drain pan has been sloped for drainage during the defrost cycle.

DRAIN LINE

The drain line should be run from the drain connection, sloping at least 1” (25 mm) per foot and should have the size at least as large as the drain connection. A P-Trap in a warm area outside the room must be provided to allow proper draining through the tubing. Connection should be made to proper drainage facilities that comply with local regulations. To prevent freeze-up when the temperature of the refrigerated space is 35°F (2°C) or lower, the drain line should be heated along its run inside the cold room. The heated drain line should be insulated. It is recommended that the heater be energized at all times. A heat input of 20 watts per foot in a 28°F (-2°C) room and 30 watts per foot for -20°F (-29°C) rooms, is satisfactory. Drain line heaters are not required for constant room temperature above 35°F (2°C). Always trap evaporator drain line individually to prevent vapor migration.

Ensure that the drain line has su󰀩cient slope for

proper drainage (prevention of ice build up/blockage in pan).

Page 25

TPLP

23/12/16

T30-TPLP-PDI-11

- 25 -

INSTALLATION INSTRUCTIONS

60Hz

PIPING

Refrigerationgradepipingmustbeusedforalleld

refrigeration piping. Refrigerant line sizes are important and may not be the same size as the coil connections. Consult ASHRAE handbook or other similar reference book for proper line sizing. Refrigerant piping and control system should be designed to prevent possible liquid slugging (from oil or refrigerant) of the compressors on start-up after the defrost cycle. Also, it should prevent oil logging and minimize refrigerant pressure drop.

WIRING

Wire system in accordance with governing standards and local codes. See data and wiring diagrams on pages 4 to 20 for typical wiring arrangement. Electrical wiring is to be sized in accordance with minimum circuit ampacity rating (MCA). Size fuses used must not exceed the Maximum Fuse Size ratings.

For ease of identifying the proper wiring terminal, unit wiring is color coded and terminal block connections are

identied.

When fan delay thermostats (combination fan delay and defrost termination) are installed, on start-up, the fans do not operate until the coil temperature is reduced to approximately 25oF (-4°C). It is normal for the fans to cycle a few times until the room temperature is brought down. At higher evaporating temperatures this control may not close and therefore should either be by-passed temporarily or replaced with an adjustable type. (set for a higher temperature cut-in point).

MAINTENANCE

The unit should be periodically inspected for any dirt or ice

build-uponthensurfaceandcleanedifnecessarywith

a soft whisk or brush. Also ensure coils inner (and outer) drain pans do not have any ice build-up from improper

defrostoperation.Whenreplacingheaterelementsrst

remove heater retainer brackets and heater clips.

SYSTEM CHECK

Before Start-Up:

1. All wiring should be in accordance with local codes.

2. Refrigerant lines should be properly sized.

3. Thorough evacuation and dehydration has been performed.

4. The suction, discharge, and receiver service valves must be open.

5.Thesystempreferablyincludealiquidlinelter  driermoistureindicatorandsuctionlter.

6. Pour enough water into the drain pan to allow a good check on drainage and seal the trap.

After Start-Up:

1. Check the oil level to be sure the oil charge is correct.

2. On initial start up the fans do not start until coil temperature is pulled down to approximately 25°F (-4°C) on the coil. Also, it is normal for the fan to cycle a few times until the room temperature is pulled down.

3. If necessary, temporarily by-pass fan delay control (to run fans until room temp is lowered).

4. Be sure that the expansion valve is properly set to provide the correct amount of superheat.

5. After the box temperature is close to reaching the desired temperature, the evaporator superheat must be checked and adjustment made if necessary. In general, evaporators running with a TD of 10°F (5.6°C ) should have a superheat reading of 6° to 8°F (3.3°C to 4.4°C). For evaporators with another T.D., the general rule is that the superheat should be around 60 to 80% of T .D.

6. Heavy moisture loads are usually encountered

 whenstartingthesystemforthersttime. 

This may cause a rapid build-up of frost on the evaporator. During the initial pull down, we suggest that the frost build-up be watched and defrosted manually as required.

7. Observe that the system goes through at least one complete DEFROST CYCLE.

Page 26

SERVICE PARTS

23/12/16

T30-TPLP-PDI-11

- 26 -

TPLP 60Hz

FOR SERVICE PARTS LOOK-UP:

visit: http://www.t-rp.com/serv_parts.htm

email: parts@t-rp.com

call: 1-844-893-3222 x501

Page 27

FINISHED GOODS WARRANTY

23/12/16

T30-TPLP-PDI-11

- 27 -

The terms and conditions as described below in the General Warranty Policy cover all products manufactured by National Refrigeration.

GENERAL WARRANTY POLICY

Subject to the terms and conditions hereof, the Company warrants all Products, including Service Parts, manufactured by the Company to be free of defects in material or workmanship, under normal use and application for a period of one (1) year from the original date of installation, or eighteen

(18)monthsfromthedateofshipmentfromtheCompany,whicheveroccursrst.Anyreplacement

part(s) so supplied will be warranted for the balance of the product’s original warranty. The part(s) to be replaced must be made available in exchange for the replacement part(s) and reasonable proof

oftheoriginalinstallationdateoftheproductmustbepresentedinordertoestablishthee󰀨ective dateofthewarranty,failingwhich,thee󰀨ectivedatewillbebaseduponthedateofmanufactureplus

thirty (30) days. Any labour, material, refrigerant, transportation, freight or other charges incurred in connection with the performance of this warranty will be the responsibility of the owner at the cur-

rentratesandpricesthenine󰀨ect.Thiswarrantymaybetransferredtoasubsequentownerofthe

product.

THIS WARRANTY DOES NOT COVER

(a)Damagescausedbyaccident,abuse,negligence,misuse,riot,re,ood,orActsofGod(b)damages

caused by operating the product in a corrosive atmosphere (c) damages caused by any unauthorized

alterationorrepairofthesystema󰀨ectingtheproduct’sreliabilityorperformance(d)damagescaused

by improper matching or application of the product or the product’s components (e) damages caused by failing to provide routine and proper maintenance or service to the product (f) expenses incurred for the erecting, disconnecting, or dismantling the product (g) parts used in connection with normal maintenance,

suchasltersorbelts(h)productsnolongeratthesiteoftheoriginalinstallation(i)productsinstalled

or operated other than in accordance with the printed instructions, with the local installation or building codes and with good trade practices (j) products lost or stolen.

No one is authorized to change this WARRANTY or to create for or on behalf of the Company any other obligation or liability in connection with the Product(s). There is no other representation, warranty or condition in any respect, expressed or implied, made by or binding upon the Company other than the above or as provided by provincial or state law and which cannot be limited or excluded by such law, nor will we be liable in any way for incidental, consequential, or special damages however caused.

Theprovisionsofthisadditionalwrittenwarrantyareinadditiontoandnotamodicationoforsubtraction

from the statutory warranties and other rights and remedies provided by Federal, Provincial or State laws.

PROJECT INFORMATION

System Model Number Date of Start-Up

Serial Number Service Contractor Refrigerant Phone Electrical Supply Fax

Page 28

“AS BUILT” SERVICE PARTS LIST

23/12/16

T30-TPLP-PDI-11

- 28 -

Service Parts List

Label

To Be Attached

HERE

Due to National Refrigeration’s policy of continuous product improvement, we reserve the right to make changes without notice.

NATIONAL REFRIGERATION & AIR CONDITIONING CANADA CORP.

159 Roy Blvd. Brantford Ontario Canada N3R 7K1 PHONE: (519) 751-0444 800-463-9517 FAX (519) 753-1140 www.t-rp.com