TRENTON DP2, DP2GX User Manual

TRENTON Technology Inc.
2350 Centennial Drive • Gainesville, Georgia 30504
Sales [phone] • Phone [phone] • Fax [phone]

Technical Information – Jumpers, Connectors and Memory
DP2/DP2GX (5664-xxx) System Host Board

Layout Diagram

Jumpers & LEDs

The setup of the configuration jumpers on the SHB is described below. An asterisk (*) indicates the default value of
each jumper.
NOTE: For two-position jumpers (3-post), "RIGHT" is toward the bracket end of the board; "LEFT" is toward the
memory sockets.

JU7

COMBO I/O (P5A) SPEAKER CONNECT

(Also refer to JU18 - Combo I/O Reset Connect.)

INSTALL= Connect speaker data signal to pin 8 of Combo I/O connector (P5A) *

REMOVE= Disconnect

JU8 Password Clear

Install for one power-up cycle to reset the password to the default (null password).
Remove for normal operation. *

JU9

CRT TYPE SELECT

LEFT = Monochrome
RIGHT = Color *

JU10/11 SYSTEM FLASH ROM OPERATIONAL MODES

The Flash ROM has two programmable sections: the Boot Block for "flashing" in the BIOS and the Main
Block for the executable BIOS and PnP parameters. Normally only the Main Block is updated when a new
BIOS is flashed into the system.

Program All (Boot and Main)

Normal PnP (Program Main Block)

Write Protect

JU12 CMOS Clear

JU10 JU11

Right Right

Right * Left *

Left

Left

Trenton Support Center – DP2/DP2GX Technical Information -- Jumpers, Connectors and Memory

1

TRENTON Technology Inc.
2350 Centennial Drive • Gainesville, Georgia 30504
Sales [phone] • Phone [phone] • Fax [phone]

INSTALL = Clear CMOS
REMOVE = Operate *

NOTE: The CMOS Clear jumper works on power-up. To clear the CMOS, power down the system, install
the jumper, then turn the power back on. CMOS is cleared during the POST routines. Then power down the
system again and remove the jumper before the next power-up.

JU13 SCSI TERMINATION ENABLE

(Not available on BASIC model)

INSTALL= Disable on-board active termination for SCSI interface

REMOVE= Enable *

JU14 FAN SPEED MONITOR

This jumper must be removed (disabled).

JU15 3.3V MONITOR ENABLE

INSTALL = Enable 3.3V monitor
REMOVE = Disable monitor *

NOTE: JU15 enables the 3.3V monitor, which monitors the 3.3V power plane of the backplane. This voltage
is routed to the SBC via the PICMG® connector. The monitor generates a RESET to the SBC if 3.3V is
below tolerance. If your system does not supply 3.3V to the backplane, this jumper must be removed
(disabled).

JU16 WATCHDOG TIMER

LEFT = Normal reset *
RIGHT = Enable watchdog

JU17 INTERRUPT 12 (IRQ12) SELECT

INSTALL = IRQ12 dedicated to PS/2 mouse *
REMOVE = IRQ12 available for system use

JU18 COMBO I/O (P5A) RESET CONNECT

(Also refer to JU7 = Combo I/O Speaker Connect.)

INSTALL= Connect reset data signal to pin 1 of Combo I/O connector (P5A) *

REMOVE= Disconnect

JU19 SCSI ACTIVITY LED ENABLE

(not available on BASIC model)

INSTALL= Light the hard drive LED for SCSI drive activity*

REMOVE= No SCSI drive (i.e., the SCSI controller is not being used)

JU20 DUAL PROCESSOR ENABLE

INSTALL = Enable dual processor operation *
REMOVE = Single processor operation

CPU SPEED JUMPERS

There are four jumpers (W3, W4, W5 and W6) which must be set correctly to allow the SBC to take full
advantage of the speed of the Pentium II/III microprocessor. These jumpers must be set as specified below.

CPU Synthesizer Jumpers

Speed Frequency

850MHz 100MHz In Out In Out

800MHz 100MHz Out In In Out

750MHz 100MHz Out Out Out In

Trenton Support Center – DP2/DP2GX Technical Information -- Jumpers, Connectors and Memory

W4* W3 W6 W5

2

TRENTON Technology Inc.
2350 Centennial Drive • Gainesville, Georgia 30504
Sales [phone] • Phone [phone] • Fax [phone]

700MHz 100MHz Out In Out In

650MHz 100MHz Out Out In In

600MHz 100MHz Out In In In

550MHz 100MHz In Out Out Out

500MHz 100MHz In In Out Out

450MHz 100MHz In Out In Out

400MHz 100MHz In In In Out

350MHz 100MHz In Out Out In

333MHz 66MHz In In Out Out

300MHz 66MHz In Out In Out

266MHz 66MHz In In In Out

NOTE: In revision D-D-02 and earlier, W4 was hard-wired in an "In" position

ETHERNET LEDS AND CONNECTORS

The Ethernet interface has two LEDs for status indication and an RJ-45 network connector.

LED/Connector

Link/Activity LED

Speed LED

RJ-45 Network
Connector

(flashing)

Description

Green LED which indicates the link status.

Off = The Ethernet interface did not find a valid link on the network connection. Transmit and receive are

not possible.

On =

The Ethernet interface has a valid link on the network connection and is ready for normal operation.

(solid)

The Speed LED identifies connection speed.

On =

Indicates network transmit or receive activity.

Amber LED which identifies connection speed.

Off = Indicates a 10Mb/s connection.

On = Indicates a 100Mb/s connection.

The RJ-45 network connector requires a category 5 (CAT5) unshielded twisted-pair (UTP) 2-pair
cable for a 100-Mb/s network connection or a category 3 (CAT3) or higher UTP 2-pair cable for a
10-Mb/s network connection.

Trenton Support Center – DP2/DP2GX Technical Information -- Jumpers, Connectors and Memory

3

TRENTON Technology Inc.
2350 Centennial Drive • Gainesville, Georgia 30504
Sales [phone] • Phone [phone] • Fax [phone]

Connectors

NOTE:

Pin 1 on the connectors is indicated by the square pad
on the PCB.

P2 - KEYLOCK CONNECTOR

5 pin single row header, Amp #640456-5

PIN SIGNAL

1 LED Power

2 Key

3 Gnd

4 Keylock Data

5 Gnd

P3 - FLOPPY DRIVE CONNECTOR

34 pin dual row header,
Robinson Nugent #IDH-34LP-S3-TR

PIN SIGNAL

1 Gnd

3 Gnd

PIN SIGNAL

2 N-RPM

4 NC

P11 - PRIMARY IDE HARD DRIVE CONNECTOR

40 pin dual row header,
Robinson Nugent #IDH-40LP-S3-TR

PIN SIGNAL

1 Reset

3 Data 7

5 Data 6

7 Data 5

9 Data 4

11 Data 3

13 Data 2

15 Data 1

17 Data 0

19 Gnd

21 DRQ 0

23 IOW

25 IOR

PIN SIGNAL

2 Gnd

4 Data 8

6 Data 9

8 Data 10

10 Data 11

12 Data 12

14 Data 13

16 Data 14

18 Data 15

20 NC

22 Gnd

24 Gnd

26 Gnd

5 Gnd

7 Gnd

9 Gnd

11 Gnd

13 Gnd

15 Gnd

17 Gnd

19 Gnd

21 Gnd

23 Gnd

25 Gnd

27 Gnd

29 Gnd

31 Gnd

33 Gnd

6 D-Rate0

8 P-Index

10 N-Motoron 1

12 N-Drive Sel2

14 N-Drive Sel1

16 N-Motoron 2

18 N-Dir

20 N-Stop Step

22 N-Write Data

24 N-Write Gate

26 P-Track 0

28 P-Write Protect

30 N-Read Data

32 N-Side Select

34 Disk Chng

27 IORDY

29 DACK 0

31 IRQ 14

33 Add 1

35 Add 0

37 CS 1P

39 IDEACTP

28 SELPDP

30 Gnd

32 NC

34 Gnd

36 Add 2

38 CS 3P

40 Gnd

P11A - SECONDARY IDE HARD DRIVE CONNECTOR

40 pin dual row header,
Robinson Nugent #IDH-40LP-S3-TR

PIN SIGNAL

1 Reset

3 Data 7

5 Data 6

7 Data 5

9 Data 4

11 Data 3

PIN SIGNAL

2 Gnd

4 Data 8

6 Data 9

8 Data 10

10 Data 11

12 Data 12

Trenton Support Center – DP2/DP2GX Technical Information -- Jumpers, Connectors and Memory

4

TRENTON Technology Inc.
2350 Centennial Drive • Gainesville, Georgia 30504
Sales [phone] • Phone [phone] • Fax [phone]

Connectors (Continued)

P4 - KEYBOARD CONNECTOR

6 pin mini DIN, Kycon #KMDG-6S-BS-PS

PIN SIGNAL

1 Kbd Data

2 Reserved

3 Gnd

4 Kbd Power (+5V fused) with self-resetting fuse

5 Kbd Clock

6 Reserved

P4A - KEYBOARD HEADER

5 pin single row header, Amp #640456-5

PIN SIGNAL

1 Kbd Clock

2 Kbd Data

3 Key

4 Kbd Gnd

5 Kbd Power (+5V fused) with self-resetting fuse

P5 - SPEAKER PORT CONNECTOR

4 pin single row header, Amp #640456-4

PIN SIGNAL

1 Speaker Data

2 Key

3 Gnd

4 +5V

P5A - COMBO I/O CONNECTOR

8 pin single row header, Amp #640456-8

PIN SIGNAL

1 Reset (See JU18 in Configuration Jumpers above.)

2 Gnd

3 NC

4 Kbd Clock

5 Kbd Data

13 Data 2

15 Data 1

17 Data 0

19 Gnd

21 DRQ 1

23 IOW

25 IOR

27 IORDY

29 DACK 1

31 IRQ15

33 Add 1

35 Add 0

37 CS 1S

39 IDEACTS

14 Data 13

16 Data 14

18 Data 15

20 NC

22 Gnd

24 Gnd

26 Gnd

28 SELPDS

30 Gnd

32 NC

34 Gnd

36 Add 2

38 CS 3S

40 Gnd

P12 - HARD DRIVE LED CONNECTOR

4 pin single row header, Amp #640456-4
(This connector is used for both IDE and SCSI drives. See

PIN SIGNAL

1 +5V Pullup

2 Light

3 Light

4 +5V Pullup

JU19 in the Jumpers section.)

P13 - PCI ULTRA3 SCSI CONTROLLER CONNECTOR

(not available on BASIC models)
50/68 high density SCSI connector, Amp #749069-7

PIN SIGNAL

1 Gnd

2 Gnd

3 Gnd

4 Gnd

5 Gnd

6 Gnd

7 Gnd

PIN SIGNAL

35 SCZDB12

36 SCZDB13

37 SCZDB14

38 SCZDB15

39 SCZDBPH

40 SCZDB0

41 SCZDB1

Trenton Support Center – DP2/DP2GX Technical Information -- Jumpers, Connectors and Memory

5

TRENTON Technology Inc.
2350 Centennial Drive • Gainesville, Georgia 30504
Sales [phone] • Phone [phone] • Fax [phone]

6 Kbd Lock Data

7 Kbd Power (+5V fused) with self-resetting fuse

8 Speaker Data

Connectors (Continued)

P6 - SERIAL PORT 1 CONNECTOR

10 pin dual row header, 3M #30310-6002HB

PIN SIGNAL

1 Carrier Detect

3 Receive Data-I

5 Transmit Data-0

Data Terminal

7

Ready-0

9 Signal Gnd

PIN SIGNAL

2 Data Set Ready-I

4 Request to Send-O

6 Clear to Send-I

8 Ring Indicator-I

10 NC

P7 - SERIAL PORT 2 CONNECTOR

10 pin dual row header, 3M #30310-6002HB

PIN SIGNAL

1 Carrier Detect

3 Receive Data-I

5 Transmit Data-0

Data Terminal

7

Ready-0

9 Signal Gnd

PIN SIGNAL

2 Data Set Ready-I

4 Request to Send-O

6 Clear to Send-I

8 Ring Indicator-I

10 NC

P8 - PARALLEL PORT CONNECTOR

26 pin dual row header, 3M #30326-6002HB

PIN SIGNAL

1 Strobe

3 Data Bit 0

5 Data Bit 1

7 Data Bit 2

PIN SIGNAL

2 Auto Feed XT

4 Error

6 Init

8 Slct In

8 Gnd

9 Gnd

10 Gnd

11 Gnd

12 Gnd

13 Gnd

14 Gnd

15 Gnd

16 Gnd

17 TERMPWR

18 TERMPWR

19 NC

20 Gnd

21 Gnd

22 Gnd

23 Gnd

24 Gnd

25 Gnd

26 Gnd

27 Gnd

28 Gnd

29 Gnd

30 Gnd

31 Gnd

32 Gnd

33 Gnd

34 WIDEPS

42 SCZDB2

43 SCZDB3

44 SCZDB4

45 SCZDB5

46 SCZDB6

47 SCZDB7

48 SCZDBP

49 Gnd

50 Gnd

51 TERMPWR

52 TERMPWR

53 NC

54 Gnd

55 SCZATN

56 Gnd

57 SCZBSY

58 SCZACK

59 SCZRST

60 SCZMSG

61 SCZSEL

62 SCZCD

63 SCZREQ

64 SCZIO

65 SCZDB8

66 SCZDB9

67 SCZDB10

68 SCZDB11

P15 - PCI SVGA INTERFACE CONNECTOR

(not available on BASIC models)
15 pin VGA connector, Amp #748390-5

9 Data Bit 3

11 Data Bit 4

13 Data Bit 5

15 Data Bit 6

10 Gnd

12 Gnd

14 Gnd

16 Gnd

PIN SIGNAL

1 Red

2 Green

3 Blue

Trenton Support Center – DP2/DP2GX Technical Information -- Jumpers, Connectors and Memory

PIN SIGNAL

6 Gnd

7 Gnd

8 Gnd

PIN SIGNAL

11 NC

12 EEDI

13 HSYNC

6

TRENTON Technology Inc.
2350 Centennial Drive • Gainesville, Georgia 30504
Sales [phone] • Phone [phone] • Fax [phone]

17 Data Bit 7

19 ACK

21 Busy

23 Paper End

25 Slct

18 Gnd

20 Gnd

22 Gnd

24 Gnd

26 NC

Connectors (Continued)

P9 - PS/2 MOUSE CONNECTOR

6 pin mini DIN, Kycon #KMDG-6S-BS-PS

PIN SIGNAL

1 Ms Data

2 Reserved

3 Gnd

4 Kbd Power (+5V fused) with self-resetting fuse

5 Ms Clock

6 Reserved

P9A - PS/2 MOUSE HEADER

6 pin single row header, Amp #640456-6

PIN SIGNAL

1 Ms Data

2 Reserved

3 Kbd Gnd

4 Kbd Power (+5V fused) with self-resetting fuse

5 Ms Clock

6 Reserved

P10 - EXTERNAL RESET CONNECTOR

2 pin header, Amp #640456-2

PIN SIGNAL

1 External Reset In (Low Active)

2 Gnd

4 NC

5 Gnd

9 +5V

10 Gnd

14 VSYNC

15 EECS

P16 - PCI 10/100BASE-T ETHERNET CONNECTOR

(not available on BASIC models)
8 pin shielded RJ-45 connector, Molex #43202-8110

PIN SIGNAL

1 TD+

2 TD-

3 RX+

4 NC

5 NC

6 RX-

7 NC

8 NC

P17 - UNIVERSAL SERIAL BUS (USB) CONNECTOR

8 pin dual row header, Molex #702-46-0821
(+5V fused with self-resetting fuses)

PIN SIGNAL

1 +5V - USB0

3 USB0-

5 USB0+

7 Gnd - USB0

P18 - SYSTEM HARDWARE MONITOR CONNECTOR

6 pin single row header, Amp #640456-6

PIN SIGNAL

1 Gnd

2 GPO (General Purpose Output)

3 CI (Chassis Intrusion Input)

4 FAN1 (Fan 1 Tachometer Input)

5 FAN2 (Fan 2 Tachometer Input)

6 OS# (Temperature Sense Output)

P19 - CPU Fan

3 pin single row header, Molex #22-23-2031

PIN SIGNAL

2 +5V - USB1

4 USB1-

6 USB1+

8 Gnd - USB1

PIN SIGNAL

Trenton Support Center – DP2/DP2GX Technical Information -- Jumpers, Connectors and Memory

7

TRENTON Technology Inc.
2350 Centennial Drive • Gainesville, Georgia 30504
Sales [phone] • Phone [phone] • Fax [phone]

1 Gnd

2 +12V

3 Fan Tach

Trenton Support Center – DP2/DP2GX Technical Information -- Jumpers, Connectors and Memory

8

TRENTON Technology Inc.
2350 Centennial Drive • Gainesville, Georgia 30504
Sales [phone] • Phone [phone] • Fax [phone]

Memory

The DRAM interface consists of two dual in-line memory module (DIMM) sockets and supports auto detection of
memory up to 512MB of Synchronous DRAM (SDRAM) for the 440BX or up to 1GB of SDRAM for the 440GX.
Minimum memory size is 8MB. The System BIOS automatically detects memory type, size and speed.

The SBC uses industry standard 64-bit or 72-bit wide gold finger DIMM DRAM in two 168-pin DIMM sockets.

NOTE: Memory can be installed in one or both DIMM sockets. If only one DIMM module is used, it must be

populated in the top DIMM socket (Bank 1 - BK1). If two modules are used, they must be the same DIMM type,
but may be different sizes (see table below). EDO DIMMs are not supported. All DIMMs must have gold contacts.

The SBC supports DIMM memory modules which are PC-100 compliant and have the following features:

• 168-pin DIMMs with gold-plated contacts

• 100MHz SDRAM

• Non-ECC (64-bit) or ECC (72-bit) memory

• 3.3 volt only

• Single or double-sided DIMMs in the sizes listed below

• Buffered or Registered configuration

DIMM Size DIMM Type Non-ECC ECC

8 MB Unbuffered 1M x 64 1M x 72

16 MB Unbuffered 2M x 64 2M x 72

32 MB Unbuffered 4M x 64 4M x 72

64 MB Unbuffered 8M x 64 8M x 72

128 MB Unbuffered 16M x 64 16M x 72

256 MB Registered 32M x 64 32M x 72

512 MB Registered 64M x 64 64M x 72 **

** DP2GX models only

All memory components and DIMMs used with the SBC must be PC-100 compliant, which means that they comply
with Intel's PC SDRAM specifications. These include the PC SDRAM Specification (memory component specific),
the PC Unbuffered DIMM Specification, the PC Registered DIMM Specification and the PC Serial Presence Detect
Specification.

Trenton Support Center – DP2/DP2GX Technical Information -- Jumpers, Connectors and Memory

9