TI-PE80
8-Port Industrial Fast Ethernet PoE+ DIN-Rail Switch
TI-PE80 (v1.0R)
• 8 x Fast Ethernet PoE+ ports
• 200W PoE power budget
• 1.6Gbps switching capacity
• Hardened IP30 rated metal switch
• Includes DIN-Rail mount and wall mount brackets
• Wide operating temperature range of -40° – 75° C (-40° – 167° F)
• Dual inputs provide redundant power with overload current protection
• Alarm relay triggered by power failure
• Power supply sold separately (model: TI-S24048)
• Lifetime Warranty
TRENDnet’s Industrial Fast Ethernet PoE+ DIN-Rail Switches feature a rugged IP30 rated metal enclosure. These industrial
unmanaged PoE+ switches are designed to withstand a high degree of vibration and shock, while operating in both high and low
temperatures for industrial environments within -40° – 75° C (-40° – 167° F). Redundant power inputs with overload current
protection on each industrial unmanaged PoE+ switch minimizes network downtime.Installers and integrators can save on equipment
costs and reduce installation time with TRENDnet’s Industrial Fast Ethernet Switches by delivering up to 30W per port of PoE power
and data over existing Ethernet cables. With PoE technology, users only need one set of cables to deliver both data and power from
the industrial unmanaged PoE+ switch. With these industrial unmanaged PoE+ switches, easily network PoE devices such as highpower wireless access points, PTZ and other advanced IP cameras, VoIP phone systems, IPTV decoders, access controls, and
more.
TI-PE80
PoE+ Power
A 200W PoE+ power budget supplies up to
eight Power over Ethernet devices with PoE+
power.
NETWORKING SOLUTION
Redundant Power
Dual power inputs provide redundant power
with overload current protection, and an output
alarm relay to indicate input power failure.
Industrial Hardened Design
Equipped with a rugged IP30 rated housing,
designed to withstand a high degree of
vibration, shock, and operate within a wide
temperature range of -40° – 75° C (-40° –
167° F).
FEATURES
TI-PE80
PoE+ Power
The industrial unmanaged PoE+
switches each supply up to 30W of
power per port and data over a single
Ethernet cable to PoE devices
Redundant Power
Dual inputs provide redundant power
with overload current protection
(power supply sold separately, model:
TI-S24048)
Electro Magnetic Compliance
Complies with industrial EMS
certifications (IEC 61000-4-2) ESD:
Contact: 6kV | Air: 8kV, (IEC
61000-4-4) EFT: Power: 2kV | Signal:
2kV, (61000-4-5) Surge: Power: 2kV |
Signal: 2kV
Easy Installation
No configuration needed, simply
connect PoE+ network devices to the
industrial unmanaged PoE+ switch
Wide Temperature Range
A wide operating temperature range of
-40° – 75° C (-40° – 167° F) allows for
installations in industrial environments
with extreme hot or cold conditions
Grounding Point
Each industrial unmanaged PoE+
switch features a grounding point to
protect equipment from external
electrical surges
Mounting Hardware
IP30 rated metal enclosure with DINRail mount and wall mount hardware
included
Shock and Vibration Resistant
Rated for shock (EN 60068-2-27),
freefall (EN 60068-2-32), and vibration
(EN 60068-2-6)
SPECIFICATIONS
Standards
• IEEE 802.3
• IEEE 802.3u
• IEEE 802.3ab
• IEEE 802.3x
• IEEE 802.3af
• IEEE 802.3at
Device Interface
• 8 x Fast Ethernet PoE+ ports
• 6-pin removable terminal block
• LED indicators
• DIN-Rail mount
• Wall mount
• Grounding point
Data Transfer Rate
• Ethernet: 10Mbps (half duplex), 20Mbps (full
duplex)
• Fast Ethernet: 100Mbps (half duplex),
200Mbps (full duplex)
Performance
• Data RAM Buffer: 1MB
• Switching Fabric: 1.6Gbps
• MAC Address Table: 1K entries
• Forwarding rate: 1.19Mpps (64-byte packet
size)
DC Power
• Input: 48 – 56V DC
• Recommended power supply: TI-S24048 (sold
separately)
• Max. consumption: 5.76W (no PoE)
• PoE
• PoE budget: 200W
Terminal Block
• Redundant power inputs, alarm relay contact, 6
pin
• Wire range: 0.34mm^2 to 2.5mm^2
• Solid wire (AWG): 12-24/14-22
• Stranded wire (AWG): 12-24/14-22
• Torque: 5 lb. – In / 0.5Nm / 0.56Nm
• Wire strip length: 7-8mm
• Alarm Relay Contact
• Relay outputs with current carrying capacity of
1A, 24V DC
• Open circuit mode when two power sources
are connected
• Short circuit mode when only one power
source is connected
MTBF
• 510,304 hours
Special Features
• Hardened components rated for extreme
temperatures
• Dual redundant power inputs
• ESD 8KV support
• Low-profile design
Housing
• IP30 metal case
• DIN-Rail mount
• Wall mount
• Grounding point
Operating Temperature
• - 40° – 75° C (-40° – 167° F)
Operating Humidity
• Max. 95% non-condensing
Dimensions
• 142 x 105 x 37mm (5.6 x 4.1 x 1.5 in.)
Weight
• 486g (17.1 oz.)
TI-PE80
Certifications
• CE
• FCC
• UL
• Shock (IEC 60068-2-27)
Package Contents
• TI-PE80
• Quick Installation Guide
• Removable terminal block
• DIN-Rail and wall mount kit
• Freefall (IEC 60068-2-32)
• Vibration (IEC 60068-2-6)
Warranty
• Lifetime
TRENDnet offers a lifetime warranty for all of its metal-enclosed network switches that have been purchased in the United States/Canada on or after 1/1/2015. Cooling fan and internal power supply carry a one-year
warranty.
All references to speed are for comparison purposes only. Product specifications, size, and shape are subject to change without notice, and actual product appearance may differ from that depicted herein.
20675 Manhattan Place • Torrance • CA 90501 • USA • T: 1-888-326-6061 • F: 1-310-961-5511 • sales@trendnet.com • www.TRENDnet.com
TRENDnet is a registered trademark. Other Brands and product names are trademarks of their respective holders. Information provided in this document pertain to TRENDnet products and is subject to change at
any time, without notice. For the most recent product information please visit http://www.trendnet.com. Copyright © TRENDnet. All Rights Reserved. Updated: 8/19/2019
Loading...