Page 1
I105 V.92/V.90 PCI MODEM USER’S MANUAL
TABLE OF CONTENT
1. Contents of Package .................................................................2
2. Comprehensive Modem Installation Instructions...................2
2.1 System Requirements ...........................................................2
2.2 Hardware Installation .............................................................3
2.3 System Setup ........................................................................4
2.3.1 Setup Instructions for Windows 98SE.......................................4
2.3.2 Uninstall Modem from Windows 98SE...................................... 7
2.3.3 Setup Instructions for Windows ME ..........................................8
2.3.4 Uninstall Modem from Windows ME .......................................10
2.3.5 Setup Instructions for Windows 2000 ..................................... 11
2.3.6 Uninstall Modem from Windows 2000.....................................13
2.3.7 Setup Instructions for Windows XP.........................................14
2.3.8 Uninstall Modem from Windows XP........................................18
2.4 Testing your modem ............................................................20
2.5 Install Communication Software..........................................20
3. Troubleshooting ......................................................................21
Appendix 1: Modem Specifications ...........................................23
Appendix 2: Government Compliance....................................... 24
Rev.1.01.4.05.04
- 1 -
Page 2
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Section 1 Contents of Package
! One V.92/V.90 PCI bus window modem
! One telephone cable
! One CD-ROM disk comprises Communication software, Modem Driver & User's Manual
! Quick installation guide
Please contact the place of purchase if any of the above listed items are missing.
Section 2 Comprehensive Modem Installation Instructions
Section 2.1 System Requirements
The modem operates on a personal computer equipped with the following:
! Windows 98SE / ME / 2000 / XP Operating System
! Pentium(r) MMX 200MHz or faster CPU
! 8 MB hard disk space
! 64 MB RAM
! One vacant 32-bit PCI slot
! One available IRQ: 3 through 15
Rev.1.01.4.05.04
- 2 -
Page 3
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Section 2.2 Hardware Installation
Please refer to Fig. 2 - 1 and proceed to following steps for how to insert your modem into the computer and
connect telephone wire.
Model: I105
Figure 2-1 Internal modem diagram
1. Turn off and unplug your computer from the AC outlet.
2. Unplug any peripheral devices (keyboard, monitor, etc.) from your computer to avoid the
risk of electric shock.
3. Take the cover off your computer, review computer's manual if you need further instructions.
4. Find an empty PCI slot.
5. Unscrew the PCI slot bracket and save the screw, then remove the bracket.
6. Plug the modem into the PCI slot carefully until the modem is properly seated.
7. Fasten the modem bracket firmly with the screw saved in step 5.
8. Reassemble your computer cover and re-plug cables for peripheral.
9. Plug one end of telephone cord into the "LINE" jack at the modem's bracket. Plug another end of the
telephone cord into the telephone wall jack
10. Some models may comprise a phone jack for an optional telephone. If you wish to use a phone through
the same telephone wall jack when the modem is not in use, plug the telephone cord of the phone into
"PHONE" jack at the modem's bracket now. Lift the handset and listen for a dial tone to check for a
properly connection.
11. Plug the power cord into the computer and turn the computer on.
12. Up to now, the hardware installation has been finished. If you have not encountered any problems, you
can go to Section 2.3 System Setup. If you are having problems, see Section 3 Troubleshooting.
NOTE : The telephone wall jack you use must be for an ANALOG phone line (the type found in most homes).
Many offices are equipped with digital phone lines. Please be sure you know which type of line you have. The
modem will be damaged if you use a digital phone line.
Rev.1.01.4.05.04
- 3 -
Page 4
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Section 2.3 System Setup
Section 2.3.1 Setup instructions for Windows 98SE
STEP 1. After you complete the modem hardware installation and turn on your PC, Windows system will
automatically detect your new added devices. Windows system will then prompt you with an Add
New Hardware Wizard screen as shown in figure.
Then click on Cancel.
STEP 2. Run <CD-ROM letter>:\Drivers\Win9x\HXFSetup.exe as shown in figure.
Then click on OK.
STEP 3. Keep the Modem Driver CD-ROM disk attached with your modem in the CD-ROM drive device.
Then click on OK.
STEP 4. And then, a prompt screen will ask you to assign where your driver is located. Please select
<CD-ROM letter>:\Drivers\Win9x as shown in figure.
Then click on OK.
Rev.1.01.4.05.04
- 4 -
Page 5
I105 V.92/V.90 PCI MODEM USER’S MANUAL
STEP 5. You must be to select the correct region setting of modem for the best performance and
compatible.
Right click on My Computer icon in windows desktop then click on Properties.
STEP 6. Choose Device Manager tab. To expand Modem item, then select Generic SoftK56 Data Fax
Voice Speakerphone CARP as shown in figure.
Click on Properties
Rev.1.01.4.05.04
- 5 -
Page 6
I105 V.92/V.90 PCI MODEM USER’S MANUAL
STEP 7. Choose Region Select tab then select a region in which this modem will be used as shown in
figure.
Click on Apply and then click on OK.
Rev.1.01.4.05.04
- 6 -
Page 7
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Section 2.3.2 Uninstall Modem from Windows 98SE
STEP 1. Open Control Panel window then click on Add/Remove Programs icon.
STEP 2. Choose Install/Uninstall tab, then select Generic SoftK56 Data Fax Voice Speakerphone
CARP item as shown in figure.
Click on Add/Remove… .
Rev.1.01.4.05.04
- 7 -
Page 8
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Section 2.3.3 Setup instructions for Windows ME
STEP 1. After you complete the modem hardware installation and turn on your PC. Windows system will
automatically detect your new added devices. A prompt screen will ask you to select Specify the
location of the driver or Automatic search for a better driver as shown in figure.
Click on Cancel.
STEP 2. Please insert the Modem Driver CD-ROM disk into your CD-ROM drive device, then run
<CD-ROM letter>:\Drivers\WinMe\HXFSetup.exe as shown in figure.
Then click on OK.
STEP 3. You must be to select the correct region setting of modem for the best performance and
compatible.
Open Control Panel window, then click on HSF Modem Region Select icon as shown in figure.
Rev.1.01.4.05.04
- 8 -
Page 9
I105 V.92/V.90 PCI MODEM USER’S MANUAL
STEP 4. Then, a prompt screen will ask you to select a region in which this modem will be used.
Select the correct region and then click OK.
Rev.1.01.4.05.04
- 9 -
Page 10
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Section 2.3.4 Uninstall Modem from Windows ME
STEP 1. Open Control Panel window, then clock on Add/Remove Programs icon ash shown in figure.
STEP 2. Choose Install/Uninstall tab, then select Generic SoftK56 Data Fax Voice Speakerphone
CARP item as shown in figure.
Click on Add/Remove… .
STEP 3. You must restart your computer before the new settings will take effect.
Click on Yes
Rev.1.01.4.05.04
- 10 -
Page 11
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Section 2.3.5 Setup instructions for Windows 2000
STEP 1. After you complete the modem hardware installation and turn on your PC. Windows system will
automatically detect your new added devices. Windows system will then prompt you with a Found
New Hardware Wizard screen as shown in figure.
Click on Cancel.
STEP 2. Please insert the Modem Driver CD-ROM disk into your CD-ROM drive device, then run
<CD-ROM letter>:\Drivers\Win2K\HXFSteup.exe as shown in figure.
Then click on OK.
STEP 3. And then, the several prompt screens will be warning you that the digital signature of programs
have not found as shown in figure.
Please always click on Yes.
Rev.1.01.4.05.04
- 11 -
or
Page 12
I105 V.92/V.90 PCI MODEM USER’S MANUAL
STEP 4. The prompt screen will ask you to assign your driver is located. Please select <CD-ROM
letter>:\Drivers\Win2K as shown in figure.
Then click on Retry.
STEP 5. You must be to select the correct region setting of modem for the best performance and
compatible.
Open Control Panel and click on HSF Modem Region Select icon as shown in figure.
STEP 6. Then, a prompt screen will ask you to select a region in which this modem will be used.
Select the correct region and then click OK.
Rev.1.01.4.05.04
- 12 -
Page 13
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Section 2.3.6 Uninstall Modem from Windows 2000
STEP 1. Open Control Panel windows then click on Add/Remove Programs icon as shown in figure.
STEP 2. Select Generic SoftK56 Data Fax Voice Speakerphone CARP item then click on
Change/Remove.
The uninstall procedures have finish, when the Generic SoftK56 Data Fax Voice Speakerphone
CARP item had disappeared from the listed.
Rev.1.01.4.05.04
- 13 -
Page 14
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Section 2.3.7 Setup instructions for Windows XP
STEP 1. Right click on My Computer icon on Desktop and then select Properties as shown in figure.
STEP 2. The System Properties window will appear and then select Hardware tab as shown in figure.
Then, click on Device Manager.
STEP 3. Expand Modems item and then right click on Generic SoftK56 device as shown in figure.
Then, click on Update Driver.
Rev.1.01.4.05.04
- 14 -
Page 15
I105 V.92/V.90 PCI MODEM USER’S MANUAL
STEP 4. The Hardware Update Wizard will appear and then choose Install from a list or specific
location [Advanced] item as shown in figure.
Then click on Next.
STEP 5. Select Don’t search. I will choose the driver to install item as shown in figure.
Then, click on Next.
STEP 6 Select Generic SoftK56 item in Models listed. as shown in figure.
Then, click on Have Disk.
Rev.1.01.4.05.04
- 15 -
Page 16
I105 V.92/V.90 PCI MODEM USER’S MANUAL
STEP 7. Insert the Modem Driver CD-ROM disk attached with your modem into the CD-ROM drive device,
then specific the driver location as [F:\Drivers\WinXP] (“F” is CD-ROM drive letter).
Then click on OK.
STEP 8. The Wizard will find the updated device Generic SoftK56 Data Fax Speakerphone CARP and
then click on Next.
STEP 9. The prompt screen will appear to ask you to ensure the driver for your modem as shown in figure.
Then, click on Continue Anyway.
Rev.1.01.4.05.04
- 16 -
Page 17
I105 V.92/V.90 PCI MODEM USER’S MANUAL
STEP 10. The Hardware Update Wizard will appear again. System has finished the installation.
Click on Finish.
STEP 11. You must be to select the correct region setting of modem for the best performance and
compatible.
Open Control Panel window and then click on HSF Modem Region Select as shown in figure.
STEP 12. Then, a prompt screen will ask you to select a region in which this modem will be used.
Select the correct region then click OK.
STEP 13. You must be to reboot your system now for available use.
Rev.1.01.4.05.04
- 17 -
Page 18
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Section 2.3.8 Uninstall Modem from Windows XP
STEP 1. Right click on My Computer icon on Desktop and then select Properties as shown in figure.
STEP 2. The System Properties window will appear and then select Hardware tab as shown in figure.
Then, click on Device Manager.
STEP 3. Expand Modems item and then right click on Generic SoftK56 Data Fax Speakerphone CARP
device as shown in figure.
Then, click on Uninstall.
Rev.1.01.4.05.04
- 18 -
Page 19
I105 V.92/V.90 PCI MODEM USER’S MANUAL
STEP 4. A prompt screen will ask you to ensure to remove the selected modem.
Then, click on OK.
Rev.1.01.4.05.04
- 19 -
Page 20
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Section 2.4 Testing Your Modem
Before you set up your software, start with a quick test to check that your modem is working. Once you have
determined that your modem is setup properly, go on to Section 2.5 Install Communication Software to
install your communications software. If you are having problems, see Section 3 Troubleshooting.
Click on Start and point to Setting. Then click on Control Panel. When the Control Panel window opens.
Scroll down to the Modem icon and double click on it. Click on the Diagnostics tab and highlight the COM
port for your modem. Then click on More Info, your computer will automatically communicate with your new
modem using AT commands and receiving responses from your modem. A list of response means the
modem is setup properly.
Section 2.5 Install Communication Software
You can install the communication software from the CD-ROM disc attached with your new modem. Please
consult the software manual in the CD-ROM disc for the detail of software installation.
You do not have to use the communication software attached with your new modem. The modem was
designed for and tested using a wide range of communications software packages. Many communication
applications identify the modem automatically and configure themselves for the correct operating settings.
Some of the communication applications will ask you to select the type of modem you are using. Select a
Generic Fax class 1 modem will let you use basic communication and fax functions.
Rev.1.01.4.05.04
- 20 -
Page 21
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Section 3 Troubleshooting
Your modem is designed to provide reliable and trouble-free functionality, however, should you experience
any difficulty, the information contained in this section will assist you in determining and resolving the source
of the problem.
Problem: Modem does not respond to AT commands
Possible solutions:
1. Make sure the modem is not configured with a conflicting COM port and IRQ setting. Make sure the
communication software is configured with the correct COM and IRQ settings (the same COM port
and IRQ as the modem). Your communications software will not be able to send or receive any data if it
is not configured to match the COM port and IRQ settings for the modem.
DOS based communication program is not working with this modem neither can you operate the
modem in MS-DOS prompt screen.
2. Make sure the modem is properly initialized using the driver software. The software may improperly
Initialize your modem because you have selected an incorrect modem type. You may also be prompted
to enter an initialization string by the software. Use AT&F as your initialization string.
Problem: Modem dials but does not connect
Possible solutions:
1. Be sure the IRQ setting is identical on the modem and the software.
2. Make sure that the phone line is working properly. A noisy line will prevent proper modem operation.
Problem: Modem makes a connection but no data appears on screen
Possible solutions:
3. Make sure all communication parameters (baud rate, data, stop, and parity bits) are properly configured
and are identical on both sides. Be certain hardware flow control (RTS/CTS - default) is enabled in both
the modem and the communication software.
4. Press the ENTER key several times. The remote system may be waiting to receive your data before it
begins.
5. Make sure the correct terminal emulation mode is being used in the software (refer to software manual).
Problem: Modem displays errors while on-line with a remote modem
Possible solutions:
6. Make sure Call Waiting is turned off.
7. Make sure RTS/CTS hardware flow control is enabled (do not use XON/XOFF software flow control
when transferring binary files).
Rev.1.01.4.05.04
- 21 -
Page 22
I105 V.92/V.90 PCI MODEM USER’S MANUAL
8. Make sure the data speed is not faster than your computer capability. Operating too many applications
at the same time may cause communication problem. Close unnecessary application in your system.
Problem: Modem exhibits poor voice recording or playback
Possible solutions:
9. Make sure the correct modem type is selected in the Voice/FAX software. Volume adjustment is
available in control panel.
10. Make sure your computer is fast enough to handle voice operations (38.4 Kbps). Voice operations are
CPU intensive and require a better CPU sharing when running under Windows.
Problem: No dial tone
Possible solutions:
11. Ensure that the telephone cord it securely connected at both modem and wall outlet.
12. Unplug the telephone cord from the computer and connect it directly to a telephone from the wall outlet.
Check for a dial tone. If there is none, the problem is in the telephone cord or system. Call your
telephone service provider.
13. Double-check your country setting. Different country setting will cause different modem performance.
Please select the correct country as you located.
14. Check modem performance with a direct line from your telephone company. Some PBXs may cause the
telephone line condition change and affect modem performance.
Problem: The modem does not answer incoming calls
Possible solutions:
15. Ensure that the automatic answer parameter is set to one of the enabled options, using the ATS0
command (ATS0=1 to answer after one ring, and so on).
16. Ensure that no other devices, such as fax or answering machines, are answering calls before the
modem does.
If you can not resolve your situation after reading this section, contact your dealer or vendor for assistance.
Rev.1.01.4.05.04
- 22 -
Page 23
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Appendix 1 Modem Specifications
Modulation standard : V.92 & V.90, K56flex, V.34, V.32bis, V.32, V.22bis, V.22, V.23, V.21, Bell 212A, Bell 103
Compression : V.44, V.42bis, MNP Class 5
Error Correction : V.42, MNP Class 2-4
Host Interface : PCI bus
FAX Group : Group III
FAX Command : EIA/TIA 578 class 1
Power : 0.3 W max
Temperature : 0 to 40 degrees C, operating; -20 to 60 degrees C, non-operating
Rev.1.01.4.05.04
- 23 -
Page 24
I105 V.92/V.90 PCI MODEM USER’S MANUAL
Appendix 2 Government compliance notices
FCC compliance
This equipment complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among
other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment.
You must, upon request, provide this information to your telephone company.
If your telephone equipment causes harm to the telephone network, the Telephone Company may
discontinue your service temporarily. If possible, they will notify in advance. But, if advance notice isn’t
practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the
FCC.
Your telephone company may make changes in its facilities, equipment, operations, or procedures that could
affect proper operation of your equipment. If they do, you will be notified in advance to give you an opportunity
to maintain uninterrupted telephone service.
The FCC prohibits this equipment to be connected to party lines or coin-telephone service.
In the event that this equipment should fail to operate properly, disconnect the equipment from the phone line
to determine if it is causing the problem. If the problem is with the equipment, discontinue use and contact
your dealer or vendor.
FCC Class B statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Notice: 1) Shielded cables, if any, must be used in order to comply with the emission limits.
2) Any change or modification not expressly approved by the Grantee of the equipment
Rev.1.01.4.05.04
- 24 -
Page 25
I105 V.92/V.90 PCI MODEM USER’S MANUAL
authorization could void the users authority to operate the equipment.
DOC compliance information
NOTICE: The Canadian Department of Communications label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network protective, operational and safety
requirements. The Department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users ensure that it is permissible to be connected to the facilities of the local
Telecommunications Company. The equipment must also be installed using an acceptable method of
connection. The customer should be aware that compliance with the above conditions might not prevent
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by
the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may
give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.
NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to
be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a
loop may consist of any combination of devices subject only to the requirement that the sum of the Load
Numbers of all the devices does not exceed 100.
European CTR 21 compliance
The equipment has been approved in accordance with Council Decision 98/482/EC for pan-European single
terminal connection to the public switched telephone network (PSTN). However, due to differences between
the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional
assurance of successful operation on every PSTN network termination point. In the event of problem, you
should contact your equipment supplier in the first instance.
Note: The manufacturer should ensure that the vendor and user of the equipment is clearly informed of the
above information by means of package and /or user manuals of the forms of user instructions.
Rev.1.01.4.05.04
- 25 -
Loading...