?
?Windows 98SE/Me/2000/XP/2003 Server/Vista
?Enrutador inalámbrico o por cable
?Un servidor DHCP disponible, los enrutadores inalámbricos tienen por lo
general un servidor DHCP integrado
1
Español
Aplicación
2-Port USB/Parallel Print Server
(TE100-P11)
4-Port Gigabit Firewall Router
Internet
Parallel
Printer
10/100Mbps
USB
Printer
Cable/DSL
Modem
Workstation with
10/100Mbps PCI Adapter
(TE100-PCIWN)
Wireless 2-Port
USB/Parallel Print Server
(TEW-P11G)
Workstations with
Wireless N USB Adapter
(TEW-644UB)
(TWG-BRF114)
Worstation with
10/100Mbps PCI Adapter
(TE100-PCIWA)
Wireless N Home Router
(TEW-652BRP)
Wireless g 54Mbps
Parallel
Printer
USB
Printer
2
Español
Internet
Cable/DSL Modem
2. Cómo se instala
Nota: Por favor apague todas las impresoras antes de conectarlas al servidor
de impresoras. A continuación, encienda cada impresora después de realizar
todas sus conexiones de hardware.
1. Conecte un cable de red RJ-45 del
puerto LAN de su enrutador al
puerto LAN del servidor de
impresión.
2. Conecte una impresora USB o
Parallel a los de
impresora.
3. Conecte el adaptador de
alimentación AC al servidor de
impresión y luego a una toma de
corriente.
servidor
4. Encienda la impresora.
3
Español
3. Configuración del servidor de impresora
Nota:
Deshabilite cualquier programa antivirus o firewall (cortafuegos) antes
de empezar la instalación de hardware.
Para usuarios de Windows
1. Introduzca el CD-ROM del
controlador.
2. Haga clic en Run autorun.exe
(sólo para Windows Vista).
3. Haga clic en Setup Wizard
(Asistente de configuración).
4. Haga clic en Next (Siguiente).
4
Español
5. Seleccione el servidor de
impresión y luego haga clic en
Next (Siguiente).
6. Si lo desea, cambie el Nombre del
dispositivo, Nombre del dominio
y añada un Comentario (opcional)
Luego haga clic en Next
(Siguiente).
7. Seleccione Obtain IP Address
automatically (automáticamente
obtener dirección IP) y luego hacer clic en Next (Siguiente).
Nota: Si tiene el TE100-P11, vaya al paso 11. Si tiene el TEW-P11G, continúe
con el paso 8.
8. Seleccione la red inalámbrica
deseada y después pulse Next
(Siguiente).
5
Español
9. Las opciones de configuración
inalámbrica correspondientes se
configurarán de forma automática.
Luego haga clic en Next
(Siguiente).
10. Si se habilita, introduzca la clave
de encriptación de su red
inalámbrica y luego haga clic en
Next (Siguiente). Este ejemplo
muestra la WPA2-PSK.
11. Haga clic en Finish (Finalizar).
6
Español
12. Haga clic en OK.
13. Desconecte el cable RJ-45 y
desconecte la alimentación.
Luego, vuelva conectar la
alimentación (sólo en el
TEW-P11G)
La configuración del Servidor de Impresora se ha finalizado
Para información más detallada sobre cómo añadir impresoras para Windows
98SE/Me/2000/XP/2003 Server/Vista, consulte la Guía del Usuario que se
incluye en el CD-ROM del controlador y de la herramienta o en el sitio Web de
TRENDnet en www.trendnet.com
Para asegurar los más altos niveles de servicio y apoyo al cliente, registre su producto
Registre su producto
en línea en: www.trendnet.com/register
Gracias por elegir TRENDnet
7
Español
Troubleshooting
The Setup Wizard is unable to see my printer server. What should I do?
Q1.
First, double check your hardware connections; make sure that the print
A1.
server is powered ON and is properly connected. Second, click Refresh. Third,
disable any software firewall programs (e.g. ZoneAlarm). If your computer is
running Windows XP or Vista, disable the built in firewall program. Fourth, unplug
the power to the print server, wait 15 seconds, then plug the power back in.
How do I add a printer to my computer?
Q2.
Please refer to the User's Guide on the CD-ROM for instructions on adding a
A2.
printer.
I configured my print server to automatically receive an IP Address from a
Q3.
DHCP server but I can't log in to the browser configuration for the print server.
Open the Setup Wizard (See 3. Configure the Print Server) to locate your print
A3.
server's IP Address. Then type in the IP address into your browser.
After I successfully configured the TEW-P11G to match my wireless network
Q4.
settings, I can not connect to the print server.
First, verify that the wireless settings match your wireless network settings.
A4.
Second, make sure to disconnect the Ethernet cable from the print server and
verify that the WIRELESS LED is lit.
If you still encounter problems or have any questions regarding the TE100-P11/TEW-P11G, please refer to the User's Guide included on the Utility CD-ROM or contact
TRENDnet's Technical Support Department.
8
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com/register