TE
Treiber- und Dienstprogramm-CD
Anleitung zur Schnellinstallation
USB-Verlängerungskabel
Systemanforderungen
1. Computer mit USB-Anschluss
2. 300-MHz-Prozessor und 128 MB Arbeitsspeicher (empfohlen)
3. Mindestens 20 MB freier Speicherplatz auf der Festplatte.
4. CD-ROM-Laufwerk
5. Access Point 802.11b oder 802.11g (für den Infrastrukturmodus) oder einen
anderen drahtlosen 802.11b-Adapter (für den Ad-Hoc/Peer-to-PeerNetzwerkmodus).
6. Windows 98SE/ME/2000/XP
108Mbps High Speed
802.11g Wireless Access Point
(TEW-450APB)
54Mbps 802.11g
Wireless Access Point
(TEW-430APB)
802.11g Wireless and 512MB Flash Memory
Combo USB Adapter with HotSpot Detector
connecteddetected
108Mbps High Speed 802.11g
Wireless Access Point
(TEW-453APB)
(TEW-)429UF
*Laptop/PC is not required to detect HotSpots
1
Deutsch
108Mbps 802.11a+g
Wireless Access Point
(TEW-510APB)
108Mbps 802.11g MIMO
Wireless Access Point
(TEW-610APB)
Page 4
2. Installation
Hinweis: Schalten Sie bitte Ihren Computer ein und befolgen Sie die
untenstehenden Anweisungen.
1. Verbinden Sie den drahtlosen
USB-Adapter TEW-429UF fit dem
USB-Anschluss Ihres Computers.
2. Klicken Sie auf Install Utility &
Driver (Hilfsprogramm und Treiber
installieren).
3. Klicken Sie bei jedem
Installationsschritt auf Next
(Weiter) und anschließend auf
Install (Installieren).
HINWEIS: Die drahtlosen Adapter von TRENDnet sind bei allen unterstützten
Windows-Betriebssystemen umfassend getestet worden und bieten garantierte
Kompatibilität.
2
Deutsch
Page 5
4. Klicken Sie auf Continue Anyway
(Vorgang dennoch fortsetzen)
oder auf Yes (Ja).
5. Klicken Sie auf Finish
(Fertigstellen).
3
Deutsch
Page 6
6. Klicken Sie auf Next (Weiter).
7. Klicken Sie auf Continue Anyway
(Vorgang dennoch fortsetzen)
oder auf Yes (Ja).
8. Klicken Sie auf Finish
(Fertigstellen).
4
Deutsch
Page 7
3. Verwendung des drahtlosen Adapters
Hinweis: Wir empfehlen Ihnen, Ihren Computer neu zu starten, bevor Sie den
TEW-429UF verwenden.
1. Doppelklicken Sie auf das Symbol für
die drahtlose Kommunikation in der
Symbolleiste.
2. Klicken sie auf Site Survey (Standort-
Übersicht). Klicken Sie dann auf
Refresh (Aktualisieren) und wählen Sie
den gewünschten Access Point aus.
Klicken Sie auf Connect (Verbindung
herstellen).
3. Klicken Sie auf OK.
4. Prüfen Sie bitte Ihren
Verbindungsstatus.
Ihre Installation ist beendet!
Hinweis: Zusätzliche Informationen zu den erweiterten Funktionen finden Sie in
der Bedienungsanleitung.
5
Deutsch
Page 8
Troubleshooting
I completed all the steps in the quick installation guide, but my wireless USB
Q1:
Adapter isn't connecting to my access point. What should I do?
First, you should verify that the Network SSID matches your wireless
A1:
router or access point's SSID. Second, you should check your TCP/IP properties
to ensure that Obtain an IP address automatically is selected. Third, you can
click on the Site Survey link to check and see if there are any available wireless
networks listed.
Windows is unable to recognize my hardware. What should I do?
Q2:
Make sure your computer meets the minimum requirements as specified in
A2:
Section 1 of this quick installation guide. Also, you must install the wireless
configuration utility before connecting the wireless USB Adapter.
I cannot open the wireless configuration utility. What should I do?
Q3:
Go to your device manager (control panel system) to make sure the
A3:
adapter is installed properly. If you see a networking device with a yellow question
mark or exclamation point, you will need to reinstall the device and/or the drivers.
If you still encounter problems, please refer to the User's Guide CD-ROM or contact
technical support.
Certifications
This equipment has been tested and found to comply with FCC and CE Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received.
Including interference that may cause undesired operation.
Waste electrical and electronic products
must not be disposed of with household
waste. Please recycle where facilities
exist. Check with you Local Authority or
Retailer for recycling advice.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.