Guide d'installation rapide
Quick Installation Guide
TEG-S50g
3.01
Table des matières
Français
Avant de commencer
1.
Installation du matériel
2. 3
LEDs
3. 4
1
1
English 5
1. Before You Start 5
2. Hardware Installation 7
3. LEDs 8
Dépannage 10
Troubleshooting 11
Version 01.26.2010
1. Avant de commencer
Contenu de l'emballage
TEG-S50g
?
Guide d´installation rapide en plusieurs
?
langues
Adaptateur secteur
? (5V DC, 1A)
Configuration du système
Un ordinateur avec un adaptateur réseau correctement installé
?
? Câble CAT 5e ou CAT 6 pour réseaux
La surface doit supporter au moins 1,5 kg pour le Switch
?
?
La prise secteur doit être située à un maximum de 1,82 mètres du Switch
?
Inspectez visuellement la prise d'alimentation et assurez-vous qu'elle est
correctement connectée à l'adaptateur secteur
Vérifiez la présence d'une source de ventilation adéquate autour du Switch pour
?
une dissipation efficace de la chaleur
Ne placez pas d'objets lourds sur le Switch
?
1
Application
1
Delivers less power
to unused ports
less power
2
Delivers less power
when devices are off
off
less power
3
Delivers less power
with shorter
cable lengths
*Max power savings compared with standard TRENDnet switches.
GREENnet
Switch
Regular
Switch
20m
20m
60m
Full Power
60m
on on
on on
100m
100m
2
2. Installation du materiel
1. Branchez le transformateur au TEG-S50g
ainsi qu’à une prise de courant.
2. Branchez un câble réseau CAT-5e ou CAT-6
RJ-45 de l'ordinateur vers un port Ethernet
disponible du .TEG-S50g
3
3. LEDs
Alimentation
Vert : sous tension.
Eteint : hors tension.
Link/ACT
Vert (Fixe) : Relié à un autrepériphérique.
Vert (Clignotant) : Activité depuis cette liaison
Eteint : Rien n'est détecté sur le port.
Speed
Vert : la connexion du port est de 2000 (Full)
Eteint :
la connexion pour le port est de 10 ou 20
(Half/Full), 100 ou 200 (Half/Full) rien n'est détecté
sur le port.
4
1. Before You Start
Package Contents
TEG-S50g
?
?Multi-Language Quick Installation Guide
?Power Adapter (5V DC, 1A)
System Requirements
? A computer with a network adapter installed
? Cat-5e or Cat-6 Network Cable
The surface must support at least 1.5 Kg for the Switch
?
The power outlet should be within 1.82 meters (6 feet) of the Switch
?
Visually inspect the DC power jack to make sure that it is securely connected to
?
the power adapter
Make sure that there is proper heat dissipation from and adequate ventilation
?
around the Switch
Do not place heavy objects on the Switch
?
5
Application
1
Delivers less power
to unused ports
less power
2
Delivers less power
when devices are off
off
less power
3
Delivers less power
with shorter
cable lengths
*Max power savings compared with standard TRENDnet switches.
GREENnet
Switch
Regular
Switch
20m
20m
60m
Full Power
60m
on on
on on
100m
100m
6
2. Hardware Installation 2. Hardware Installation
1. Connect the Power Adapter to the TEG-S50g
and then to a power outlet.
2. Connect a CAT-5e or CAT-6 RJ-45 network
cable from the computer to an available
Ethernet port of the TEG-S50g.
7
3. LEDs
Power
Green: Power is on
Not Illuminated: Power is off
Link/ACT
Green(Solid): Link to another device.
Green(Blinking): Activity is occurring from the link
Not Illuminated: Nothing is detected on the port.
Speed
Green: Connection for the port is 2000Mbps (Full)
Not Illuminated:
Connection to the port is 10/20Mbps (Half/Full),
100/200Mbps (Half/Full) or nothing is detected on
the port.
8
Technical Specifications
Hardware
Standards IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3ab 1000Base-T
IEEE 802.3x Flow Control
IEEE 802.3 az (draft 2.0)
Network Media
Ethernet: Cat. 3, 4, 5, up to 100m
Fast Ethernet: Cat. 5, up to 100m
Gigabit Ethernet: Cat. 5, 5e, 6, up to 100m
Data Rate
Protocol/Topology
Power Consumption
Switch Fabric 10Gbps forwarding capacity
Interface 5 x 10/100/1000Mbps Auto-MDIX RJ-45 ports
Data RAM Buffer
Filtering Table
Jumbo Frame Support
Diagnostic LEDs
Power Adapter
Dimension
Weight
Temperature
Humidity
Certifications
* Max power savings compared with standard TRENDnet switches.
Ethernet: 10Mbps/20Mbps (half/full-duplex)
Fast Ethernet: 100Mbps/200Mbps (half/full-duplex)
Gigabit Ethernet: 2000Mbps (full-duplex)
CSMA/CD, Star
3 Watts (max)
128KBytes
8K entries
9216Bytes
Power, Link/ACT, 100Mbps/1000Mbps
5V DC, 1A external power adapter
116 x 25 x 70mm (4.57 x 0.98 x 2.76 in.)
225 g (7.8 oz)
Operating: 0° ~ 40° C (32° ~ 104° F)
Storage: -10° ~ 70° C (14° ~ 158° F)
Max. 90% (non-condensing)
FCC, CE
9
Dépannage
1. Les voyants ne s'allument pas lorsque le Switch est branché sur le secteur.
1.
Vérifiez que l'adaptateur d'alimentation externe du TEG-S50g est bien branché
à la prise de courant.
2. Vérifiez également que la prise murale est sous tension.
2.
Lorsque je branche un ordinateur à l'un des ports du Switch, le voyant
Link/ACT s'allume, mais je n'arrive pas à obtenir des vitesses Gigabit.
1.
Si le voyant 1000Mbps n'est pas allumé, la vitesse de connexion de l'ordinateur
est de 10Mbps ou de 100Mbps.
2. Vérifiez le câble Ethernet. Assurez-vous que vous utilisez des câbles Ethernet
CAT-5e ou CAT-6. Certains câbles CAT-5 ne permettent pas les connexions
Gigabit.
3. Assurez-vous que vous avez bien une carte réseau Ethernet Gigabit installée
sur votre ordinateur.
3.
Après avoir connecté mon PC au Switch, je n'arrive pas à partager mes
fichiers.
1.
En premier, regardez les voyants du Switch. Assurez-vous que le voyant
Link/ACT est allumé.
2. Vérifiez le câble réseau. La longueur minimale du câble est de 1,5 mètre et la
longueur maximale est de 100 mètres
Désactivez tous les programmes de pare-feu
3.
érifiez que le partage des fichiers est activé. Veuillez contacter l'assistance
4. V
technique de votre système d'exploitation pour plus de renseignements.
4.
Une fois que mon PC est connecté au Switch, je n'arrive à accéder à l'Internet
qu'avec un seul ordinateur.
La Switch n'est pas conçu pour partager une connexion internet entre plusieurs
ordinateurs. Vous avez besoin d'un routeur Internet, comme le TW100- S4W1CA,
par exemple.
5.
Où se trouve le port Uplink du Switch ?
C
omme tous les ports du Switch sont Auto-MDIX, tous les ports peuvent être
utilisés comme des ports uplink.
Si vous rencontrez encore des problèmes ou si vous avez des questions concernant le
TEG-S50g veuillez consulter le guide de l'utilisateur fourni sur le CD-ROM avec l'utilitaire et le
pilote ou contactez le service d'assistance technique de TRENDnet.
10
Troubleshooting
1. After connecting the Switch to a power outlet, the LEDs do not turn on.
Check the connection of the external power adapter to the TEG-S50g and the
power outlet. Also check that the power outlet is receiving power.
2.
When I connect a computer to one of the ports on the Switch, the Power and
the Link/ACT LED is lit, but I am not getting Gigabit speeds.
1.
Check the LEDs. If the Speed LED is off, the computer's connection speed is
10Mbps or 100Mbps.
2. Check the Ethernet Cable. Make sure you are using CAT-5e or CAT-6 Ethernet
Cables. Some CAT-5 cables are not rated to run in Gigabit.
3. Make sure that you have a Gigabit Ethernet adapter installed on your computer.
3.
After I connect my PCs to the Switch, I am unable to share files.
1.
Check the LEDs on the Switch. Make sure the Link/ACT LED is on.
2. Check the network cable. The minimum length of the cable is 1.5 meters and
the maximum length of the cable is 100 meters.
3. Disable any software firewall program.
4. Verify that you have file sharing enabled. Please contact your Operating System
support for more information.
4.
After I connect my PCs to the Switch, I can only get onto the Internet from one
computer.
The Switch was not designed to share Internet between multiple computers. You
need to get an Internet router such as the TW100-S4W1CA.
5.
Where is the uplink port located on the Switch?
Since all the ports on the Switch are Auto-MDIX, any of the ports can be used as
an uplink port.
If you still encounter problems or have any questions regarding the TEG-S50g please
contact Trendnet's Technical Support Department.
11
Limited Warranty
TRENDnet warrants its products against defects in material and workmanship, under normal
use and service, for the following lengths of time from the date of purchase.
TEG-S50g - 3 Years Limited Warranty
AC/DC Power Adapter, Cooling Fan and Power Supply carry a 1 year limited warranty
If a product does not operate as warranted during the applicable warranty period, TRENDnet
shall reserve the right, at its expense, to repair or replace the defective product or part and
deliver an equivalent product or part to the customer. The repair/replacement unit's warranty
continues from the original date of purchase. All products that are replaced become the
property of TRENDnet. Replacement products may be new or reconditioned. TRENDnet
does not issue refunds or credit. Please contact the point-of-purchase for their return policies.
TRENDnet shall not be responsible for any software, firmware, information, or memory data of
customer contained in, stored on, or integrated with any products returned to TRENDnet
pursuant to any warranty.
There are no user serviceable parts inside the product. Do not remove or attempt to service the
product by any unauthorized service center. This warranty is voided if (i) the product has been
modified or repaired by any unauthorized service center, (ii) the product was subject to accident,
abuse, or improper use (iii) the product was subject to conditions more severe than those
specified in the manual.
Warranty service may be obtained by contacting TRENDnet within the applicable warranty
period and providing a copy of the dated proof of the purchase. Upon proper submission of
required documentation a Return Material Authorization (RMA) number will be issued. An RMA
number is required in order to initiate warranty service support for all TRENDnet products.
Products that are sent to TRENDnet for RMA service must have the RMA number marked on the
outside of return packages and sent to TRENDnet prepaid, insured and packaged appropriately
for safe shipment. Customers shipping from outside of the USA and Canada are responsible for
return shipping fees. Customers shipping from outside of the USA are responsible for custom
charges, including but not limited to, duty, tax, and other fees.
12
WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS
WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT TRENDNET'S
OPTION, REPAIR OR REPLACE. THE FOREGOING WARRANTIES AND REMEDIES ARE
EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME
FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION
MAINTENANCE OR USE OF TRENDNET'S PRODUCTS.
TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND
EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT
EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT,
IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR
MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY
ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO
EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN
CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL,
INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE
OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER
FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION,
MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE
POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR,
REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET'S OPTION.
THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY
REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.
Governing Law: This Limited Warranty shall be governed by the laws of the state of California.
Some TRENDnet products include software code written by third party developers. These codes
are subject to the GNU General Public License ("GPL") or GNU Lesser General Public License
("LGPL").
http://www.trendnet.com/gpl http://www.trendnet.com
Go to or Download section and look for
the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are
distributed WITHOUT WARRANTY and are subject to the copyrights of the developers.
TRENDnet does not provide technical support for these codes. Please go to
http://www.gnu.org/licenses/gpl.txt http://www.gnu.org/licenses/lgpl.txt
each license.
or for specific terms of
PWP05202009v2
13
Copyright ©2010. All Rights Reserved. TRENDnet.
Loading...