TEG-S40TXD
4-Port 10/100/1000Mbps
Gigabit Ethernet Switch
User’s Guide
FCC Warning
This equipment has been tested and found to comply with the
regulations for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are design ed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with this user’s guide, may
cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct
the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference, in which case the user
may be required to take adequate measures.
VCCI Warning
This is a product of VCCI Class A Compliance.
UL Warning
a) Elevated Operating Ambient Temperature-If installed in a
closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room
ambient. Therefore, consideration should be given to installing
the equipment in an environment compatible with the
manufacturer's maximum rated ambient temperature (Tmra).
b) Reduced Air Flow- Installation of the equipment in a rack
should be such that the amount of air flow required for safe
operation of the equipment is not compromised.
c) Mechanical Loading-Mounting of the equipment in the rack
should be such that a hazardous condition is not achieved due to
uneven mechanical loading.
d) Circuit Overloading- Consideration should be given to the
connection of the equipment to the supply circuit and the effect
that overloading of circuits might have on over current
protection and supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing
this concern.
e) Reliable Earthing-Reliable earthing of rack-mounted
equipment should be maintained. Particular attention should be
iii
given to supply connections other than direct connections to the
branch circuit (e.g., use of power strips).
P/N : 1907GSW604T5000
T ABLE OF CONTENTS
ABOUT THIS GUIDE..................................................................1
T ERMS .......................................................................................1
OVERVIEW OF THIS USER’S GUIDE...............................................1
INTRODUCTION........................................................................3
GIGABIT ETHERNET T ECHNOLOGY .............................................3
S WITCHING TECHNOLOGY .........................................................4
FEATURES..................................................................................5
UNPACKING AND SETUP.........................................................8
UNPACKING...............................................................................8
S ETUP ........................................................................................8
DESKTOP INSTALLATION............................................................8
RACK INSTALLATION (OPTIONAL)............................................ ..9
CONNECTING NETWORK CABLE...............................................10
AC P OWER..............................................................................10
IDENTIFYING EXTERNAL COMPONENTS ............................13
FRONT PANEL ..........................................................................13
REAR PANEL............................................................................14
LED INDICATORS.....................................................................14
TECHNICAL SPECIFICATIONS.............................................17
A BOUT THIS GUIDE
This user’s guide tells you how to install your 4-Port
10/100/1000Mbps Gigabit Ethernet Switch and how to connect
it to your Gigabit Ethernet network.
Terms
For simplicity, this documentation uses the terms “Switch”
(first letter upper case) to refer to this 4-Port 10/100/1000Mbps
Gigabit Ethernet Switch, and “switch” (first letter lower case) to
refer to all the Ethernet switches; including the 4-Port
10/100/1000Mbps Gigabit Ethernet Switch.
Overview of this User’s Guide
?? Introduction: Describes the Switch and its features.
?? Unpacking and Setup: Helps you get started with the
basic installation of the Switch.
?? Identifying External Components: Describes the front
panel, rear panel, and LED indicators of the Switch.
?? Technical Specifications: Lists all the technical
specifications of the Switch.
1
INTRODUCTION
This section describes the features of the 4-Port
10/100/1000Mbps Gigabit Ethernet Switch and provides some
background information about Gigabit Ethernet and switching
technology.
Gigabit Ethernet Technology
Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing
the same packet structure, format, and support for CSMA/CD
protocol, full duplex, flow control, and management objects, but
with a tenfold increase in theoretical throughput over 100-Mbps
Fast Ethernet and a hundredfold increase over 10-Mbps
Ethernet. Since it is compatible with all 10-Mbps and 100Mbps Ethernet environments, Gigabit Ethernet provides a
straightforward upgrade without wasting a comp any’s existing
investment in hardware, software, and trained personnel.
The increased speed and extra bandwidth offered by Gigabit
Ethernet is essential for coping with the network bottlenecks
that frequently develop as computers and their busses get faster
and more users use applications that generate more traffic.
Upgrading key components, such as your backbone and servers
to Gigabit Ethernet can greatly improve network response times
3
as well as significantly speed up the traffic between your
subnets.
Gigabit Ethernet supports video conferencing, complex imaging,
and similar data-intensive applications. Likewise, since data
transfers occur 10 times faster than Fast Ethernet, servers
outfitted with Gigabit Ethernet NIC’s are able to perform 10
times the number of operations in the same amount of time.
Switching Technology
Another key development pushing the limits of Ethernet
technology is in the field of switching technology. A switch
bridges Ethernet packets at the MAC address level of the
Ethernet protocol transmitting among connected Ethernet or fast
Ethernet LAN segments.
Switching is a cost-effective way of increasing the total network
capacity available to users on a local area network. A switch
increases capacity and decreases network loading by making it
possible for a local area network to be divided into different
segments which don’t compete with each other for network
transmission capacity, giving a decreased load on each.
The switch acts as a high-speed selective bridge between the
individual segments. Traffic that needs to go from one segment
4
to another is automatically forwarded by the switch, without
interfering with any other segments. This allows the total
network capacity to be multiplied, while still maintaining the
same network cabling and adapter cards.
Switching LAN technology is a marked improvement over the
previous generation of network bridges, which were
characterized by higher latencies. Routers have also been used
to segment local area networks, but the cost of a router and the
setup and maintenance required make routers relatively
impractical. Today’s switches are an ideal solution to most
kinds of local area network congestion problems.
Features
The 4-Port 10/100/1000Mbps Gigabit Ethernet Switch was
designed for easy installation and high performance in an
environment where traffic on the network and the number of
users increase continuously.
?? 4 x 10/100/1000Mbps Auto-negotiation Gigabit
Ethernet ports
?? Auto-MDIX for each port
?? Supports Full/Half duplex transfer mode for 10 and
5
100Mbps
?? Support Full duplex transfer mode for 1000Mbps
?? Wire speed reception and transmission
?? Store-and-Forward switching method
?? S upports 8K entries absolute MAC address table
?? Supports 256K Bytes RAM for data buffering
?? Extensive front-panel diagnostic LEDs
?? IEEE 802.3x flow control for full-duplex
?? Back pressure flow control for half-duplex
?? Optional Rack-mount Kit for 19” standard rack
6
7
U NPACKING AND SETUP
This chapter provides unpacking and setup information for the
Switch.
Unpacking
Open the shipping carton of the Switch and carefully unpack its
contents. The carton should contain the following items:
?? One 4-Port 10/100/1000Mbps Gigabit Ethernet Switch
?? Four rubber feet with adhesive backing
?? One AC power cord
?? This user’s guide
If any item is missing or damaged, please contact your local
reseller for replacement.
Setup
The setup of the Switch can be performed using the following
steps:
?? The surface must support at least 5 kg.
8
?? The power outlet should be within 1.82 meters (6 feet)
of the device.
?? Visually inspect the power cord and see that it is
secured fully to the AC power connector.
?? Make sure that there is proper heat dissipation from
and adequate ventilation around the Switch. Do not
place heavy objects on the Switch.
Desktop Installation
When installing the Switch on a desktop or shelf, the rubber feet
included with the device must be attached first. Attach these
cushioning feet on the bottom at each corner of the device.
Allow enough ventilation space between the device and the
objects around it.
9
Gigabit Ethernet Switch installed on a Desktop or Shelf
Rack Installation (optional)
The 4-Port 10/100/1000Mbps Gigabit Ethernet Switch can be
mounted in an EIA standard size, 19-inch rack, which can be
placed in a wiring closet with other equipment. To install, attach
the mounting brackets on the Switch’s front panel (one on each
side) and secure them with the provided screws.
10
Attaching the mounting brackets to the Switch
Then, use the screws provided with the equipment rack to
mount the Switch in the rack.
Installing the Switch on the equipment rack
Connecting Network Cable
The 4-Port 10/100/1000Mbps Gigabit Ethernet Switch
supports four 10/100/1000Mbps Gigabit Ethernet ports. These
ports support half or full duplex mode when running in 10Mbps
11
or 100Mbps. They support full duplex while running in
1000Mbps.
These ports are Auto-MDIX type port. They can auto
transform to MDI-II or MDI-X medium type, so you can just
make an connection with a straight or crossover cable.
AC Power
The 4-Port 10/100/1000Mbps Gigabit Ethernet Switch can be
used with 100~240V AC, 50~60 Hz power source. The power
supply of the Switch will adjust to the local power
specification automatically and may be turned on without
having any or all LAN segment cables connected.
12
1000BASE-T Gigabit Ethernet Ports
IDENTIFYINGE XTERNAL COMPONENTS
This chapter describes the front panel, rear panel and LED
indicators of the Switch
Front Panel
The front panel of the Switch consists of four 1000BASE-T
ports and LED indicators.
LED Indicators
?? Four Gigabit Ethernet ports of 10/100/1000Mbps
Auto-Negotiation interface.
?? Comprehensive LED indicators display the conditions
of the Switch and status of the network. A description
of these LED indicators follows (see LED Indicators).
Front panel view of the Switch
13
Rear Panel
The rear panel of the Switch consists of an AC power
connector. The following figure shows the rear panel of the
Switch.
Rear panel view of the Switch
?? AC Power Connector: This is a three-pronged
connector that supports the power cord. Plug in the
female connector of the provided power cord into this
connector, and the male into a power outlet.
Supported input voltages range from 100~240V AC at
50~60 Hz.
LED Indicators
The LED indicators of the Switch including Power, Link/Act,
1000Mbps and 100Mbps. The following shows the LED
indicators for the Switch along with explanation of each
indicator.
14
The Switch LED indicators
?? POWER
This indicator lights green when the Switch is receiving
power. It is off for no power.
?? Link/Act
This LED indicator lights green when there is a valid
connection (or link) to the port . The LED indicator blinks
whenever there is reception or transmission (i.e. Activity—
Act) of data at a port.
?? 1000Mbps
This LED indicator lights green when there is a valid
1000Mbps Gigabit Ethernet connection (or link) to the port.
?? 100Mbps
15
This LED indicator lights green when there is a valid
connection (or link) to 100Mbps Fast Ethernet device at the
port.
If the connection (or link) is 10Mbps, both 1000Mbps and
100Mbps LED indicators are off.
16
T ECHNICAL SPECIFICATIONS
General
Standards: IEEE 802.3ab 1000BASE-T
IEEE 802.3u 100BASE-TX
IEEE 820.3 10BASE-T
Protocol: CSMA/CD
Data
Transfer
Rate:
Topology: Star
Network
Cables:
Number of
Ports:
Gigabit Ethernet: 2000Mbps (Full-duplex)
Ethernet: 2-pair UTP/STP Cat. 3,4,5 Cable
Fast Ethernet: 2-pair UTP/STP Cat. 5 Cable
Gigabit Ethernet: 4-pair UTP/STP Cat. 5 Cable
Four(4) 10/100/1000Mbps Auto-Negotiation
and Auto-MDIX ports
10Mbps (Half-duplex) Ethernet:
20Mbps (Full-duplex)
100Mbps (Half-duplex) Fast Ethernet:
200Mbps (Full-duplex)
17
Physical and Environmental
AC inputs: 100 ~ 240VAC Universal, 50/60 Hz
Power
Consumption:
Operating
Temperature:
Storage
Temperature:
Humidity: 5% ~ 95% RH, non-condensing
Dimensions: 280(W) × 180(D) × 44(H) mm
Weight: 1.6Kg
EMI:
Safety: cUL, TUV/GS
12 watts maximum
0 ?C ~ 40?C
-10?C ~ 55?C
FCC Class A, CE Mark Class A, VCCI
Class A
18
Performance
Transmission
Method:
RAM Buffer: 256K Bytes per device
Filtering Address
Table:
Packet
Filtering/Forwardi
ng Rate:
MAC Address
Learning:
Store-and-forward
8K MAC address per device
10Mbps Ethernet: 14,880 pps
100Mbps Fast Et hernet: 148,800 pps
1000Mbps Gigabit Ethernet: 1,488,000
pps
Self-learning, auto-aging
19
Loading...