Trendnet TEG-S2620i Quick Installation Guide

Quick Installation Guide

TEG-S2620i

H/W: V1.0R

Table of Contents

Table of Contents

English ......................................................................................................

1. Before You Start

2. Hardware Installation ........................................................................

3. Configure the Switch .........................................................................

Troubleshooting ........................................................................................

................................................................................

1

1
2
3

6

Version 05.08.2008

1. Before You Start

Package Contents

?

TEG-S2620i

?Multi-Language Quick Installation

Guide

?User's Guide CD-ROM
?RS-232 cable
? Power Cord
? Rack Mount Kit

System Requirements

?

Web Browser: Internet Explorer (5.5 or higher)

?A computer with a network adapter properly installed
?TCP/IP protocol
?One RJ-45 network cable

Optional Equipment

?

EIA standard 19” rack

?Mini-GBIC module (e.g. TEG-MGBSX, TEG-MGBS10, TEG-MGBS40,

TEG-MGBS80, TEG-MGBS10D3_D5, TEG-MGBS40D3_D5) for Mini
GBIC slots

Application

Virtual LAN

Console Terminal

RS-232

26-Port 10/100Mbps Layer 2 Switch with

Gigabit Ethernet Ports and Mini-GBIC Slots

1000MbpsRS-232 Console 10/100Mbps

(TEG-S2620i)

8-Port 100Base-FX Layer 2

Managed Switch with Mini GBIC Slot

(TEG-S811Fi)

1

English

Virtual LAN

Network Servers

2. Hardware Installation

1. Connect the Power Cord to
the TEG-S2620i and then to a
power outlet. Then press on the
switch to power up the
TEG-S2620i.

2. Connect a RJ-45 network cable
from the computer to an available
Ethernet port on the TEG-S2620i.

3. Verify that the following panel lights
are on: POWER and LINK/ACT.

2

English

3. Configure the Switch

Note: It is recommended that you configure the Switch from a wired computer.
Before the Switch can be configured, a Static IP address must be assigned to
your computer's network adapter in the subnet of 192.168.223.x. Since the
Switch's default IP address is 192.168.223.100, make sure no other network
devices are assigned an IP address of 192.168.223.100. (Refer to
Troubleshooting section on how to configure TCP/IP settings on your PC.)

Web Browser

1. Open your web browser, type
http://192.168.223.100 in the
Address bar, and then press Enter.

2. Enter the User Name and

Password, and then click OK.
By default:
User Name: admin

Password: 123

3. Select the desired options for
configuring the SNMP switch.

3

English

HyperTerminal

1. Connect the RS-232 cable from a

serial port on your Windows PC to
the console port on your computer.

2. Go to Start -> Programs ->

Accessories -> Communications ->
HyperTerminal.

3. Enter a name, choose an icon and
then click OK.

4. Select the correct COM port (e.g.
COM1, COM2) and then click OK.

English

4

5. Enter the following, click Apply

and then click OK:
Bits per second: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None

6. Press Enter.

7. Enter the User Name and

Password, and then hit Enter.
By default:
User Name: admin

Password: 123

Your configuration is now complete.

For detailed information regarding the TEG-S2620i's configuration and
advanced settings, please refer to the Troubleshooting section, User's Guide
CD-ROM, or TRENDnet's website at http://www.trendnet.com.

Register Your Product

To ensure the highest level of customer service and support, please take a moment to

To ensure the highest level of customer service and support, please take a moment to

register your product Online at: www.trendnet.com/register

register your product Online at: www.trendnet.com/register

Register Your Product

Thank you for choosing TRENDnet

Thank you for choosing TRENDnet

5

English

Troubleshooting

Q1: How do I configure TCP/IP settings on my computer?

1. Go into the Control Panel, double-click the Network

Connections icon, and then right-click the Local Area
Connection icon and then click Properties.

2. Click Internet Protocol (TCP/IP) and then click
Properties. Then click on Use the following IP
address, and make sure you assign your network

adapter an IP address in the subnet of 192.168.223.x.

: I typed http://192.168.223.100 in my Internet Browser's Address Bar, but an error message

Q2:

says “The page cannot be displayed.” How can I get into the TEG-S2620i's web configuration
page?

First, check your hardware settings again by following the instructions in section 2.

A2:

Second, make sure the POWER and LINK/ACT lights are lit. Third, make sure the TCP/IP
settings are configured properly (see Q1). Fourth, since the Switch's default IP address is

192.168.223.100, make sure that no other network devices are assigned an IP address of

192.168.223.100.

Q3:

If my network's IP is different than the Switch's range, what should I do?

You should still configure the Switch first. After all the settings are applied, go to the

A3:

Switch's configuration page, click on Administrator, click IP & Management Mode and change
the IP address of the Switch to match your network's IP.

Q4:

What are the default port settings for configuring the Switch through the console port

using HyperTerminal?

Bits per Second: 115200; Data bits: 8; Parity: None; Stop bits: 1; Flow control: None.

A3:

If you still encounter problems or have any questions regarding the TEG-S2620i, please contact
TRENDnet's Technical Support Department.

6

Certifications

This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.

Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.

ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.

TRENDnet Technical Support

.

US Canada

Toll Free Telephone: [phone]

24/7 Tech Support

Europe (Germany France Italy Spain Switzerland UK)

Toll Free Telephone: [phone]

English/Espanol - 24/7

. . . . .

Worldwide

Telephone: +(31) (0) 20 504 05 35

English/Espanol - 24/7

Product Warranty Registration

Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com/register

20675 Manhattan Place
Torrance, CA 90501
USA

Copyright ©2008. All Rights Reserved. TRENDnet.