Quick Installation Guide
TE100-PCIFC
1.01
Table of Contents
Table of Contents
Español .....................................................................................................
1. Antes de iniciar ..................................................................................
2. ...........................................................................Cómo se instala .....
Troubleshooting .........................................................................................
1
1
2
5
Version 06.11.2009
1. Antes de iniciar
Contenidos del paquete
TE100-PCIFC
?
?CD-ROM del controlador
Guía de instalación rápida
?
multilingüe
Requisitos del sistema
Ranura PCI 2.2 de 32 bits
?
?Unidad de CD-ROM
?CPU: 300 MHz o superior/ 800 MHz o superior (Windows Vista)
?Memoria: 256MB de RAM o más/ 512MB de RAM o más (Windows Vista)
?Windows 98SE/ME/2000/2003 Server(32/64-bit) / XP(32/64-bit) /
Vista (32/64-bit)
?Un cable de fibra multimodo de 62.5/125 µm
?Convertidor de fibra recomendado: TFC-110MSC o TFC-210MSC
?Conmutador Gigabit recomendado: TEG-424WS
Aplicación
24-Port 10/100Mbps Web Smart Switch
with 4 Gigabit Ports and 2 Mini-GBIC Slots
(TEG-424WS)
EthernetFiber
100Base Multi-Mode SC
Fiber-to-PCI Adapter
(TE100-PCIFC)
100Base-TX to 100Base-FX
Multi Mode SC Fiber Converter
(TFC-110MSC)
Internet
1
Español
Cable/DSL
Modem
2. Cómo se instala
Nota:
1. Para la instalación del controlador de Windows 98SE y ME, consulte la guía
del usuario en el CD-ROM del controlador
2. No conecte el TE100-PCIFC a su PC a menos que se le indique.
1. Inserte el CD-ROM del controlador
en su unidad de CD-ROM.
2. Haga clic en Run Autorun.exe
(sólo para Windows Vista).
3. Haga clic en Install Driver
(Instalar controlador) y luego haga
clic en su sistema operativo.
2
Español
4. Haga clic en OK.
5. Apaque su PC y luego abra la caja
de su PC.
6. Introduzca la tarjeta PCIe de
manera firme en la ranura para
tarjeta PCIe disponible, después
ENCIENDA el PC y espere hasta
que aparezca el escritorio de
Windows.
7. Los controladores se instalarán
automáticamente.
3
Español
Cómo conectar el a su redTE100-PCIFC
1. Conecte un cable multimodo tipo
SC del TE100-PCIFC al
convertidor de fibra a 10/100Mbps
(Ej. TFC-110MSC)
Nota: Compruebe que los cables
TX y RX están invertidos en la
conexión opuesta.
2. Conecte un cable Ethernet del
convertidor de fibra a un puerto
Gigabit Ethernet en su conmutador
(Ej. TEG-424WS).
La instalación ha sido completada
Si desea más información sobre la configuración del y sus
TE100-PCIFC
configuraciones avanzadas, por favor consulte la Guía del usuario del el
CD-ROM de la Guía del usuario.
Registre su producto
Para asegurar los más altos niveles de servicio y apoyo al cliente, registre su producto
en línea en: www.trendnet.com/register
Gracias por elegir TRENDnet
4
Español
Troubleshooting
I inserted the Driver CD-ROM into my computer's CD-ROM drive and the installation
Q1:
menu does not appear automatically. What should I do?
For Windows 2000/XP/2003 Server, if the installation menu does not appear
A1:
automatically, click Start, click Run, and type D:\autorun where "D" in "D:\autorun.exe" is the
letter assigned to your CD-ROM Drive, and then press the ENTER key on your keyboard. For
Windows Vista, if the installation menu does not appear automatically, click Start, click the
Start Search box, and type D:\autorun.exe where "D" in "D:\autorun.exe" is the letter assigned
to your CD-ROM Drive, and then press the ENTER key on your keyboard.
Windows doesn't recognize my new hardware. What should I do?
Q2:
First, verify that your computer meets the system requirements as specified in Section 1.
A2:
Second, access your device manager to make sure the adapter is installed properly. If you see
a networking device with a yellow question mark or exclamation point, you will need to reinstall
the device and/or the drivers. To access the device manager on Windows 2000/XP, right-click
My Computer, click Properties, click the Hardware tab, and then click Device Manager. To
access the device manager on Windows Vista, right-click Computer, click Properties and then
click Device Manager. Third, if the device manager fails to recognize the presence of a new
networking adapter, verify that the network adapter is firmly seated in the PCI slot. Fourth, plug
the adapter into another PCI slot on your computer.
Windows recognizes my new hardware, but I'm unable to connect to my network. What
Q3:
should I do?
First, verify that the cable is securely connected from your switch or router to your network
A3:
adapter. Second, verify that the LEDs on your network card are lit. Third, verify that the TCP/IP
settings are set to Obtain an IP address automatically (see the steps below).
Windows Vista
1. Go into the Control Panel, click Network
and Internet, click Network and Sharing
Center, click Manage Network
connections and then right-click the Local
Area Connection icon and then click
Properties.
2. Click Internet Protocol Version 4(TCP/IPv4)
and then click Properties. Then click on
Obtain an IP address automatically.
5
Windows XP/2000
1. Go into the Control Panel, double-click the
Network Connections icon and then right-
click the Local Area Connection icon and
then click Properties.
2. Click Internet Protocol (TCP/IP) and
then click Properties. Then click on
Obtain an IP address automatically.
Q4:
I am not getting a network connection when I connect the TE100-PCIFC to my network.
What should I do?
A4:
cable. Second, make sure the TX and RX cables are reversed on the opposing connection.
Q5:
If you still encounter problems or have any questions regarding the TE100-PCIFC, please refer to
the User's Guide included on the Driver CD-ROM or contact TRENDnet's Technical Support
Department.
First, check the fiber cable. Make sure you are using 62.5/125µm multi-mode fiber
What is the maximum distance that is supported by the adapter?
A5:
2 kilometers.
6
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentacón
necesario para su funcionamiento. El uso de un adaptador distinto al mencionado puede producir
daños fisicos y/o daños al equipo conectado. El adaptador de alimentación debe operar con voltaje y
frecuencia de la energia electrica domiciliaria existente en el pais o zona de instalación.
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com/register
20675 Manhattan Place
Torrance, CA 90501
USA
Copyright ©2009. All Rights Reserved. TRENDnet.
Loading...