TRENDnet TE100-P1U, 10-100Mbps mini Print Server, TE100-P1P User Manual
Table of Contents
Chapter 1 Introduction 1
Features......................................................................................................................... 1
Safety Instructions ........................................................................................................ 2
Package Contents.......................................................................................................... 3
Hardware Details .......................................................................................................... 3
Chapter 2 LAN Installation 6
Procedure......................................................................................................................6
Chapter 3 Print Server Configuration 7
Overview ......................................................................................................................7
Using the Windows Wizard.......................................................................................... 7
Chapter 4 Client PC Configuration 9
Overview ......................................................................................................................9
Windows Peer to Peer Printing................................................................................... 11
Windows SMB Printing.............................................................................................. 18
Windows with Server-based Print Queues .................................................................20
Macintosh (AppleTalk)............................................................................................... 21
Macintosh OS X .........................................................................................................22
Chapter 5 BiAdmin Management Utility 24
Requirements..............................................................................................................24
Installation .................................................................................................................. 24
Operation .................................................................................................................... 24
Chapter 6 Web-Based Management 34
Overview ....................................................................................................................34
Preparation.................................................................................................................. 34
Connecting to the Print Server.................................................................................... 35
Configuration Screens ................................................................................................35
Chapter 7 Special Features 40
Overview ....................................................................................................................40
Internet Printing Protocol(IPP)...................................................................................40
Internet Mail Printing .................................................................................................44
Chapter 8 Troubleshooting 49
Overview ....................................................................................................................49
Hardware & LAN Problems ....................................................................................... 49
AppleTalk (Macintosh)............................................................................................... 50
Windows Printing Problems.......................................................................................52
Page i
Unix Troubleshooting................................................................................................. 56
Appendix A Specifications 57
General Specifications................................................................................................57
Appendix B Windows Server Configuration 59
Windows NT 4.0 Server ............................................................................................. 59
Windows 2000/2003 Server .......................................................................................60
Appendix C Unix Systems 61
Overview ....................................................................................................................61
Print Server IP Address Configuration ....................................................................... 61
Other Print Server Configuration................................................................................ 61
LPD Printing............................................................................................................... 62
Appendix D NetWare 67
Overview ....................................................................................................................67
Creating an NDPS Manager Object............................................................................ 67
Creating an NDPS Printer Agent................................................................................68
Page ii
Chapter 1
Introduction
This chapter provides an overview of your Print Server's features.
Features
Congratulations on the purchase of your new Print Server. Your Print Server was designed to
provide a simple and efficient network printing solution. It is packed with features, including:
Versatility. The Print Server supports up to four protocols: TCP/IP, SMB (Service
Message Block), AppleTalk (EtherTalk), and NetBEUI. It features a 10/100BaseT
Ethernet interface port for connection to your LAN and operating system support includes
Unix, NetWare (NDPS LPR printing), and Microsoft Windows.
Easy Installation. The Print Server makes adding printers or plotters to your network
simple.
Easy Setup. A number of utility programs are supplied to simplify setup. For Windows
95/98/Me/NT/2000/XP users, the BiAdmin program makes it easy to configure the Print
Server for a variety of network and server configurations.
Web-based Interface. The Web-based interface provides an easy method of
configuration in TCP/IP networks regardless of your operating system.
Compact Size. This allows the Print Server to be used even where space is limited.
Remote Management Tools. A variety of software tools are provided. In most
environments, both the Print Server and attached bi-directional printers can be configured
remotely.
Internet Printing Protocol (IPP) Support. The Print Server can act as an IPP
(Internet Printing Protocol) Server, allowing clients, suppliers, colleagues and others to
print to your printer from anywhere on the Internet. Windows IPP Client software is also
supplied on the CD-ROM.
Page 1
Safety Instructions
For your own safety, and to protect your Print Server, please observe the following safety
advice.
1. Unplug this device from its power source before cleaning. Use only a slightly dampened
cloth for cleaning. Do not use liquid or aerosol cleaners.
2. Avoid using this product near water. Exposure to water poses an electric-shock hazard.
3. Do not place the Print Server on an unstable surface. The device may fall causing serious
damage to the device.
4. This device should only be used with the power supply type specified on the marking label.
If you are not sure of type of your local power supply, consult your dealer or the local
power company.
5. Do not pinch, crimp or otherwise damage the power cord. If exposed to foot traffic,
ensures that the cable is properly shielded and does not pose a tripping hazard.
6. If using an extension cord, makes sure the total ampere rating of the products using the
cord does not exceed the extension cord's ampere rating.
7. Do not attempt to service this device, as opening or removing casing may expose you to
dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
8. The Print Server should be serviced by qualified service personnel under the following
conditions:
• The power cord is damaged or frayed.
• Liquid has been spilled onto the product.
• The product has been exposed to rain or water.
• The product does not operate normally in accordance with the operating instructions.
• The device has been dropped or the casing has been damaged.
Page 2
Package Contents
You should find the following items packaged with your Print Server. If any items are missing,
contact your dealer immediately.
• The Print Server unit
• Power Adapter
• One CD-ROM containing all support programs and this manual
• Quick Install Guide
Hardware Details
Details of the LEDs and connections are in this Chapter. Further details are contained in
Appendix A - Specifications.
TE100-P1U Print Server
• 1 USB Printer Port
• 10/100BaseT LAN connection
Figure 1: TE100-P1U Print Server
Page 3
TE100-P1P Print Server
• Direct Attach
• 1 Parallel Port
• 10/100BaseT
Figure 2: TE100-P1P Print Server
Page 4
LED Indicators
The TE100-P1U has two LED indicators on the top; the TE100-P1P's LEDs are on the end.
The Error LED is red. The Status indicator LED is green. The LED indicator modes are
described in the following table.
Status LED
(Green)
Off Off No power.
On Off Normal operation - Idle.
Flashing Off Normal operation - transmitting or
On On Hardware error.
On Flashing (USB only) No printer connected to the USB port.
Flashing Flashing Firmware upgrade in progress.
Error LED
(Red)
Status Description
receiving packets from the network.
Diagnostic Push Button
The button is recessed; a pin or paper clip can be used to press it. This button has 2 functions:
• Restore the factory default settings
• Print a test page containing all current settings.
To restore the factory default settings:
1. Turn the Print Server OFF.
2. Press and hold the diagnostic button. While pressing the button, switch the Print Server
ON.
3. If you continue pressing the button for 10 seconds, a diagnostic page will be printed,
showing the new (default) settings.
To generate a Diagnostic print out
1. Ensure that both the Print Server and the attached printer are ON.
2. Press the diagnostic button, and hold it in for 2 seconds.
3. The test page, containing the current settings, will be printed.
Note:
PostScript printers are unable to print this page. If you have a PostScript printer, the test
page will not be printed.
Page 5
Chapter 2
LAN Installation
This chapter describes how to install the Print Server in your Local Area Network.
Procedure
1. Preparation
• Ensure the power is OFF. Do not connect the Print Server while power is On.
• Find the Default Server Name for your Print Server. The Default Server Name is shown on
a sticker on the base of the device. It consists of 8 letters and/or digits. Record this name; it
may be needed during configuration.
2. Connect the Printer
• For the TE100-P1U, use the cable supplied with your printer to connect the printer to the
USB port on the Print Server unit.
• For the TE100-P1P, connect the male parallel port on the Print Server directly to the
printer.
3. Connect the Network Cable
• Connect the network cable to the 10/100BaseT LAN connector on the Print Server.
4. Power Up
Plug in the power adapter cable and power up. Start-up will take only a few seconds.
Use only the Power Supply unit provided with the Print Server. Using a different Power
Supply may cause damage.
5. Check the LEDs
• The Error LED should flash, then turn Off. When the Error LED goes off and the Status
LED remains lit or flashes, the Print Server is ready.
• On the TE100-P1P, either the 10BaseT (yellow) LED or the 100BaseT (orange) LED
should be On.
• On the TE100-P1U, the Error LED will remain flashing if the Print Server can't connect to
the USB printer.
Page 6
Chapter 3
Print Server Configuration
This chapter provides an overview of the configuration process.
Overview
The Print Server is designed to support many different platforms, and the configuration
required would depend upon the environment in which it is installed.
• The Print Server usually requires configuration, but if there's a DHCP server on your
network, then the device is just plug-and-play. A Windows-based setup Wizard is also
provided on the CD-ROM to simplify this task.
• PCs wishing to use the printer attached to the Print Server always require configuration.
See Chapter 4- Client Configuration for details.
• If you wish to use a queue-based printing system using Windows NT Server/Windows
2000/Windows XP, the Network Server must be configured as detailed in Appendix B -
Windows Server Configuration. However, it is not necessary to use a Network Serverbased queue; client PCs can print directly to the Print Server using the Peer-to-peer
Printing installed by the User setup option on the CD-ROM.
Configuration Methods
The following methods are available to perform the required Print Server configuration:
• Windows-based Wizard - see below for details.
• BiAdmin management utility program - see Chapter 8 for details.
• Web-based setup - see Chapter 6 for details.
Advanced Configuration and Management
The BiAdmin management utility is provided for advanced configuration and management.
This program is installed by default when the Administrator install option is chosen. See
Chapter 5 for details on using BiAdmin.
Using the Windows Wizard
The Windows-based Wizard is supplied on the CD-ROM, and runs on Windows 95, 98, NT4.0,
ME, Windows 2000 and Windows XP.
Using this Wizard is the recommended method to configure the Print Server.
It can be used configure the Print Server for your Network environment, even if the Print
Server does not have a valid IP address.
Procedure
1. Insert the supplied CD-ROM into your drive. If the setup program does not start
automatically, run SETUP.exe in the root folder.
2. On the first screen, shown below, click Setup Wizard.
Page 7
Figure 3: Print Server Screen
3. Click Next on the first screen of the Wizard, to view a list of Print Servers on your LAN.
4. Select your new Print Server, then click Next to continue.
5. Enter the required data on the following screen.
• Name of the Print Server can be changed if you wish.
• Comment is optional.
• Select or enter the Workgroup name for this Print Server.
6. Click Next to configure the TCP/IP Screen:
• Select Obtain IP Address automatically if your LAN has a DHCP Server, otherwise
select Fixed IP Address.
• For Fixed IP Address, enter an unused address from the range used on your LAN, or
click the Suggest New Values Button.
Use the same Network Mask and Gateway as PCs on your LAN.
7. Click Finish to save the data to the Print Server.
Note: To install the Wizard on your PC, use the "Installation" option.
If the desired Print Server is not listed:
• Check all cables to the Print Server.
• Check the Print Server's LEDs:
The Red LED should be OFF and the Green LED should be ON or flashing.
Page 8
Chapter 4
Client PC Configuration
The chapter details the client configuration required on LAN clients to use the printer
or printers attached to the Print Server.
Overview
Before performing client configuration, the Print Server must be installed on your LAN, and
configured as described in Chapter 3. Both the Print Server and the attached printer must be
powered ON.
Printing Methods
The Print Server supports a number of printing methods:
• Peer-to-peer Printing means that the print jobs are stored (queued) on your PC, and sent
directly to the Print Server when it is available.
• Server-based Print Queue means that all print jobs are stored (queued) on the Network
Server (e.g. Windows NT/2000) and then sent to the Print Server. This allows the Network
Administrator to modify the Print Queue. For example, an important job can be moved to
the head of the queue.
• Windows SMB printing is a Microsoft standard for using a "Network Printer". No
additional software needs to be installed on your Windows PC, and printing from MSDOS programs is supported. However, because the Print Server can not store files, large
print jobs may cause problems.
• AppleTalk is also supported, and normally no configuration of the Print Server is required.
See the Macintosh section of this chapter for details of client configuration.
Which printing method should I use?
• If using Windows 95, 98, NT, Me, 2000, or XP, the easiest method to use is Peer-to-peer
Printing.
• If using Windows, and you need to print from MS-DOS programs, or you don't wish to
install additional software, use SMB.
However, SMB is not suitable for large, complex documents, so if you need this as well as
MS-DOS printing, you should install BOTH Peer-to-peer Printing and SMB printing. MSDOS programs can use the SMB printer, Windows programs should use Peer-to-peer
Printing.
• If your LAN has Network Servers (e.g. Windows NT, Windows 2000 Server) use the
method advised by your Network Administrator. The Print Server can print via a queue
located on a Network server, if desired.
• Unix users - refer to Appendix C - Unix Systems
• Macintosh users - refer to the Macintosh section of this chapter.
Page 9
Checking your Network Protocols (Windows 9x)
Your PC must have EITHER the TCP/IP or NetBEUI protocols installed. (All versions of
Windows after Windows 95 have TCP/IP installed by default.)
• If using the Peer-to-peer Printing, the installation program will check this for you.
• If using other methods, you must check manually, as follows:
1. Select the Settings - Control Panel - Network option on the Start Menu. You should see a
screen like the one following:
Figure 4: Network Configuration
• The top line in the list (NetBEUI -> PCI Fast Ethernet Adapter) indicates that the
NetBEUI protocol is installed on this PC. Your PC will show the name of the your
Network card rather than "PCI Fast Ethernet Adapter".
• The highlighted line (TCP/IP -> PCI Fast Ethernet Adapter) indicates that TCP/IP is
installed. Your PC will show the name of the your Network card rather than "PCI Fast
Ethernet Adapter".
2. If neither line is present:
• Install the NetBEUI protocol by selecting Add - Protocol - Microsoft - NetBEUI - OK.
You may be prompted for your Windows CD-ROM.
• If required, you can also install TCP/IP. However, depending on your LAN
environment, TCP/IP may require further configuration.
3. If either protocol is already installed, proceed with installation.
Page 10
Windows Peer to Peer Printing
With this printing method, print jobs are stored (queued) on your PC, and then sent to the Print
Server when it is available.
Figure 5: Peer-to-Peer Printing
Windows 2000 & XP require no additional software.
For other versions of Windows, the supplied PTP (Peer-to-Peer) Printer Port software must be
installed on each PC.
Windows 2000/XP Setup
The recommended printing method is to use LPR, as follows:
1. Open your Printers folder, right-click the desired printer and select Properties.
2. When prompted, choose the Ports tab and click the Add Port button.
Figure 6: Printer Ports Screen
Page 11
3. Choose Standard TCP/IP Port, then click New Port.
Figure 7: Add Port Screen
4. On the Add Standard TCP/IP Printer Port screen above, enter the IP Address of the Print
Server in the Printer Name or IP Address field, then click Next.
Figure 8: Additional Port Information Screen
5. On this screen, select Custom, and click the Settings button to view the screen below.
Page 12
Figure 9: Port Settings Screen
6. On the Port Settings screen, shown above:
• Select LPR in the Protocol section
• Enter a Queue name (L1 for Port 1, L2 for Port 2 if the Print Server has 2 printer ports)
• Ensure the LPR Byte Counting Enabled setting is Enabled.
• Click OK to confirm your changes and close this screen.
7. Follow the prompts to complete the Wizard.
Page 13
Windows 9x/ME Setup
Before performing the following procedure, the Print Server must be installed on your LAN,
and configured as described in Chapter 3. Both the Print Server and the attached printer should
be powered ON.
1. Insert the supplied CD-ROM into your drive. If the setup program does not start, run
SETUP.exe in the root folder.
2. Click the Installation button, then select the User Install.
Figure 10: Installation Screen
3. Follow the prompts to complete the installation of the Peer-to-peer Printer Port Driver.
(Refer to the Windows section of Chapter 8 - Troubleshooting if there is a problem with
the installation.)
4. The Print Driver Setup will then run.
In future, you can use Start - Programs - PrintServer Driver - Printer Port Setup to run the
program again.
PTP Printer Port Setup
1. The program will search for Printer Servers on the network, and a screen like the following
will be displayed.
• If desired, click Refresh.
• The name of the attached printer will be displayed if possible. If "No printer" is
displayed, check that the printer is properly connected and powered on.
Page 14
Figure 11: Print Port Setup (Peer-to-peer Printing)
If your Print Server is not listed:
• Click the "Refresh" button.
• Check that both the Print Server and the printer are properly connected, and
powered on.
• Check that the Print Server has been configured. (Use the Setup Wizard on
the CD-ROM.)
• If using TCP/IP, try installing the NetBEUI protocol. Then try again.
2. Select the desired port on a Print Server, then click Next. A pop-up message will inform
you if the port has been created successfully.
If you see the following error message, either install Internet
Explorer 4 or later, or follow the procedure in the "Trouble
Shooting - Windows" section of Chapter 8.
Page 15
3. The printer port will be created, then a screen like the following will be displayed.
Figure 12: Configure Printer Port
4. Select the correct Windows printer in the Existing Printers list, and click the Connect
button.
If the correct printer type is not listed, click "Add New Printer" to run the Windows Add
Printer wizard. Step through the Wizard and install the required printer:
• Select the correct Printer Manufacturer and Model, or use the "Have Disk" option if
appropriate.
• We recommend changing the Printer name to indicate which device is on.
(e.g. HP2100 on SCA43600_P1)
• If prompted about Sharing the printer, do NOT enable Sharing.
• When the Printer installation is finished, it will be listed in the Configure Printer Port
screen above. Select it and click Connect.
5. Installation is now complete. You can now print using this printer.
• To install additional Printers, repeat steps 4.
• Use the Start menu to run this program in future. The default installation is Start -
Programs - PrintServer Driver - Print Driver Setup.
Note:
If using the Epson Spooler Manager, this program must be disabled, as follows:
1. Run the Epson Spooler Manager.
2. Select "Queue Setup" from the menu.
3. Click "Use Print Manager for this port".
4. Click "OK" to exit.
Management
• Print jobs can be managed like any Windows printer. Open the Printers folder (Start -
Settings - Printers) and double-click any printer to see the current print jobs.
• If the printer attached to the Print Server is changed, just run this program again, and select
the correct printer.
• To delete a port created by this setup program, use the Windows Delete Port facility:
• Right-click any printer in the Printers folder, and select Properties.
Page 16
• Locate the Delete Port button. This button is on the Details or Ports tab, depending on
your version or Windows.
• If the Print Server's IP Address is changed, and you can no longer print, delete the port
(see procedure above) and re-install it.
Advanced Port Options
The options for the Peer-to-peer Printing are accessed via the Port Settings button.
Use Start - Settings - Printers to open the Printers folder, then right-click the Printer, and select
Properties. The Port Settings button is on the Details or Ports tab, depending on your version
of Windows.
An example screen is shown below:
Figure 13: Port Settings (Peer-to-peer Driver)
Items shown on this screen are as follows:
Port
If desired, click Browse to select a different Print Server. If the selected
device has multiple ports, the Select Device Port button can be used to
select the port.
The Port Name can not be changed after installation. This name is
shown in the Printer's Properties.
Banner
Check this option to print a banner page before each print job.
• If using a PostScript Printer, check the PostScript box.
• The User Name will be printed on the banner page.
Retry Interval
Sets how often Windows will poll the Print Server to establish a
connection when the printer is busy. Increase this value if you get too
many warning messages.
Page 17
Windows SMB Printing
This method requires no additional software to be installed, but the NetBEUI or TCP/IP
protocol must be installed on your PC. Use the following procedure to install the Print Server's
printer as a Windows SMB network printer:
1. Double-click the Network Neighborhood icon on the desktop.
2. On the View menu, select Details.
3. Locate the desired Print Server, as shown below:
• If it is the same Workgroup as your PC, it will be listed on screen.
• If it is in a different workgroup, double-click Entire Network, then double-click the
appropriate Workgroup to open it.
Figure 14: Network Neighborhood
4. Double-click the Print Server icon to view a Printer icon for each printer port. The
"Comment" field may indicate what type of printer is connected to the port.
5. To install a printer, right-click the desired printer icon, and choose "Install", as shown
below. This will start the Add Printer wizard.
Figure 15: Install SMB Printer
6. Follow the prompts to complete the installation.
• For information about the question "Do you print from MS-DOS programs?", see
Printing from MS-DOS Programs below.
• Select the Printer Manufacturer and Model to match the printer connected to this port
on the Print Server, and complete the Wizard.
7. This printer will now appear in your Printers folder (Start - Settings - Printers) and can be
used like any other printer. However, SMB printing is not suitable for large complex print
jobs - you should use the Peer-to-peer Printing instead.
Page 18
Printing from MS-DOS Programs
Windows can redirect print data from a parallel port on your PC (e.g. LPT1) to a network
printer. This redirection is called "Capture Printer Port", and is useful for MS-DOS programs.
The MS-DOS program is configured to use LPT1 (parallel port 1 on the PC), but Windows
"captures" the print data and sends it to the network printer.
Capture Settings - Windows 98/ME
1. Select Start - Settings - Printers to open the Printers folder.
2. Right-click the desired Printer, and select Properties,
Figure 16: Capture Printer Port - Windows 98/ME
3. On the Details tab, shown above, click the Capture Printer Port button to view the
Capture Printer Port dialog, as shown below.
Figure 17: Capture Dialog - Windows 98/ME
4. On this dialog:
• Select the Device (port) on the PC to be captured. Normally, this will be LPT1
(parallel port 1).
• Enter or select the Path to the printer. This will be the same as the path shown as Print
to the following port on the Printer Properties window.
• Check the Reconnect at logon checkbox. If this is not done, the capture setting will be
lost when Windows is restarted.
Page 19
Loading...