TRENDnet 100BASE-FX User Manual

Quick Installation Guide

100Base-FX

Fiber Converters

Table of Contents

Table of Contents

Deutsch .....................................................................................................

1. Bevor Sie anfangen ...........................................................................

2. ................................................................Installation der Hardware .

Spefications ..............................................................................................

Ordering Information...................................................................................

Troubleshooting ........................................................................................

1

1
2

4
5

6

Version 07.18.2006

1. Bevor Sie anfangen

Mindestanforderungen

Abwesenheit von starken Quellen elektromagnetischer Felder (wie
Motoren), Vibrationen, Staub und direkter Sonneneinstrahlung

TFC-1600-Gehäuse (optional) oder feste, ebene Oberfläche, die das
Gewicht des Konverters tragen kann

10/100 MBit/s Ethernet-Switch
Multi- oder Einzelmodus-Glasfaserkabel/ Kat. 5 RJ-45-Ethernetkabel

Produktbeschreibung

Packungsinhalt

Glasfaserkonverter
Kurzanleitung zur Installation
Netzteil (7,5 V Gleichstrom, 1,5 A)

Model Name

TFC-110MM

TFC-110MST

TFC-110MSC

TFC-15MS100

TFC-110S15

TFC-110S30

TFC-110S60

TFC-110S100

TFC-110S20D3

TFC-110S20D5

TFC-110S40D3

TFC-110S40D5

Multi/Single-Mode

Multi-Mode

(Duplex)

Single-Mode

(Duplex)

Single-Mode
Bidirectional

(Simplex)

1

Deutsch

Fiber Connector

MT-RJ

ST

SC

SC

2. Installation der Hardware

Installation eigenständiger Glasfaserkonverter

1. Verbinden Sie den
Glasfaserkonverter mit einem
Glasfaserkabel. Für den
TFC-110MM/MST/MSC ist ein
Multimodus- und für den
TFC-110S15/S30/S60/S100/
S20D3/S20D5/S40D3/S40D5 ein
Einzelmodus-Kabel erforderlich.

2. Verbinden Sie den Ethernet-Port
des Glasfaserkonverters über ein
RJ-45-Ethernetkabel mit einem
Ethernet-Port Ihres Umschalters
(z.B. TEG-224WSplus).

3. Verbinden Sie das Netzteil mit der
Buchse auf der Rückseite des
Konverters.

Hinweis: Auf der anderen Seite der Glasfaserverbindung müssen TX- und RX­Kabel vertauscht werden.

Hinweis: Der TFC-110S20D3 muss mit dem TFC-110S20D5 und der
TFC-110S40D3 mit dem TFC-110S40D5 verbunden werden.

Hinweis: Der TFC-15MS100 wandelt Multimodus- in Einzelmodus­Glasfaserverbindungen um. Wenn er mit einem Umschalter mit SC­Multimodus-Glasfaseranschluss (z.B. TEG-S2400i / TEG-S2600i / TEG-S3000i
mit Glasfasermodulen) verbunden wird, lässt sich die Reichweite des
Netzwerks über Einzelmodus-Glasfaserkabel bis zu 15 km erweitern.

2

Deutsch

Installation der Glasfaserkonverter in einem Gehäuse

4. Schrauben Sie die Abdeckung des
entsprechenden Gehäuseteils ab.

5. Lösen Sie die Schraube und
nehmen Sie den
Glasfaserkonverter aus dem
Metallgehäuse.

6. Schieben Sie den Medienkonverter
in einen freien Steckplatz und
ziehen Sie die Schraube wieder
an.

Ihre Installation ist beendet!

3

Deutsch

Specifications

Applicable Standards:

Fixed Ports:

Speed:

Forwarding rate:

LED Indicators:

DIP Switches:

Cable :

Dimensions:
Weight:

Power:
Power Consumption:

Temperature:

Humidity:

Certifications:

IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX & 100BASE-FX

1 TX port, 1 FX port

10/20Mbps for half/full-duplex
100/200Mbps for half/full-duplex

148,800pps

TFC-110 series
Per Unit: Power; Speed (100)
Per Port: FDX/COL, LINK/ACT

TFC-15MS100
Per Unit: Power
Per Port: Link/ACT

TFC-110 series: Duplex (On/half-duplex, Off/full-duplex)
TFC-15MS100: None

10BASE-T: 2-pair UTP Cat. 3,4,5

100BASE-TX: 2-pair UTP Cat. 5

100BASE-SX:

62.5/125um or 50/125um multi-mode fiber optic cable

100BASE-LX:
9/125um or 10/125um single-mode fiber optic cable

L120 × W88 × H25 mm
305 g

External power adaptor 7.5V 1.5A

7.2W Max.

Operating: 0°C ~ 40°C (32°F ~ 104°F)
Storage: -25°C ~ 70°C (-13°F ~ 158°F)

10 ~ 90%, non-condensing

FCC part 15 Class B, CISPR ClassB, VCCI Class B,
CE Mark

4

Ordering Information

Media Converters

Model Number

TFC-110MSC

TFC-110MST

TFC-110MM

TFC-110S15

TFC-110S30

TFC-110S60

TFC-110S100

TFC-110S20D3

TFC-110S20D5

TFC-110S40D3

TFC-110S40D5

TFC-15MS100

Note: MMF (multi-mode fiber); SMR (single-mode fiber)

Speed

(Mbps)

10/100

10/100

10/100

10/100

10/100

10/100

10/100

10/100

10/100

10/100

10/100

100

Port 1

Cable/Connector

Cat. 3, 4, 5,
EIA/TIA-568
100-ohm STP

Cat. 3, 4, 5,
EIA/TIA-568
100-ohm STP

Cat. 3, 4, 5,
EIA/TIA-568
100-ohm STP

Cat. 3, 4, 5,
EIA/TIA-568
100-ohm STP

Cat. 3, 4, 5,
EIA/TIA-568
100-ohm STP

Cat. 3, 4, 5,
EIA/TIA-568
100-ohm STP

Cat. 3, 4, 5,
EIA/TIA-568
100-ohm STP

Cat. 3, 4, 5,
EIA/TIA-568
100-ohm STP

Cat. 3, 4, 5,
EIA/TIA-568
100-ohm STP

Cat. 3, 4, 5,
EIA/TIA-568
100-ohm STP

Cat. 3, 4, 5,
EIA/TIA-568
100-ohm STP

MMF 1300nm
(50 or 62.5 )

µm µm

SC

Max.

Distance

100M

100M

100M

100M

100M

100M

100M

100M

100M

100M

100M

2KM

Speed

(Mbps)

100

100

100

100

100

100

100

100

100

100

100

100

Wavelength

1300nm

1300nm

1300nm

1300nm

1300nm

1300nm

1300nm

TX: 1310nm
RX: 1550nm

TX: 1310nm
RX: 1550nm

TX: 1310nm
RX: 1550nm

TX: 1310nm
RX: 1550nm

1300nm

Port 2

Cable(/125 µm )

/Connector

MMF
(50 or 62.5 )

µm µm

SC

MMF

µm µm

(50 or 62.5 )
ST

MMF
(50 or 62.5 )

µm µm

MT-RJ

SMF

µm µm

(9 or 10 )
SC

SMF

µm µm

(9 or 10 )
SC

SMF
(9 or 10 )

µm µm

SC

SMF
(9 or 10 )

µm µm

SC

Bi-directional SMF

µm µm

(9 or 10 )
SC

Bi-directional SMF
(9 or 10 )

µm µm

SC

Bi-directional SMF
(9 or 10 )

µm µm

SC

Bi-directional SMF
(9 or 10 )

µm µm

SC

SMF

µm µm

(9 or 10 )
SC

Max.

Distance

2 km

2 km

2km

15 km

30 km

60 km

100 km

20 km

20 km

40 km

40 km

15
km

5

Troubleshooting

After connecting the Fiber converter, the LEDs do not turn on. What should I

Q1:

do?

First, check that the power outlet is receiving power. Second, make sure the

A1:

power adapter is firmly connected to the Fiber converter and the power outlet.
Third, make sure the Ethernet and the Fiber cables are connected.

All the LEDs are on, but I can't make a connection. What should I do?

Q2:

First, verify that you are using the proper fiber cable (e.g. multi-mode fiber

A2:

cable for multi-mode converter; single-mode fiber cables for single-mode
converters). Second, verify that the TX and RX cables have been reverse on the
opposite Fiber connection. Third, power down the fiber converters and the
switches. Wait 15 seconds, then plug the switches and the fiber converters back
in.

What is the maximum distance that is supported by the fiber converter?

Q3:

Please reference section 4 for distance information.

A3:

If you still encounter problems or have any questions regarding the Fiber Converters
please contact TRENDnet's Technical Support Department.

6

Limited Warranty

TRENDnet warrants its products against defects in material and workmanship, under
normal use and service, for the following lengths of time from the date of purchase.

Fiber Converters

If a product does not operate as warranted above during the applicable warranty period,
TRENDnet shall, at its option and expense, repair the defective product or deliver to
customer an equivalent product to replace the defective item. All products that are
replaced will become the property of TRENDnet. Replacement products may be new or
reconditioned.

TRENDnet shall not be responsible for any software, firmware, information, or memory
data of customer contained in, stored on, or integrated with any products returned to
TRENDnet pursuant to any warranty.

There are no user serviceable parts inside the product. Do not remove or attempt to
service the product through any unauthorized service center. This warranty is voided if
(i) the product has been modified or repaired by any unauthorized service center, (ii) the
product was subject to accident, abuse, or improper use (iii) the product was subject to
conditions more severe than those specified in the manual.

Warranty service may be obtained by contacting TRENDnet office within the applicable
warranty period for a Return Material Authorization (RMA) number, accompanied by a
copy of the dated proof of the purchase. Products returned to TRENDnet must be pre­authorized by TRENDnet with RMA number marked on the outside of the package, and
sent prepaid, insured and packaged appropriately for safe shipment.

- 5 Year Warranty

7

WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE
AS WARRANTED ABOVE, THE CUSTOMER’S SOLE REMEDY SHALL BE, AT
TRENDNET’S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF
LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDNET
NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION,
MAINTENANCE OR USE OF TRENDNET’S PRODUCTS.

TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND
EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES
NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S
MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED
ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE
RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER
HAZARD.

LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET
ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER
BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND,
OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH
DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND
OF THE PURCHASE PRICE PAID, AT TRENDNET’S OPTION. THIS DISCLAIMER OF
LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED
HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.

Governing Law: This Limited Warranty shall be governed by the laws of the state of
California.

Note: AC/DC Power Adapter, Cooling Fan, Cables and Power Supply carry 1-Year
Warranty

8

Certifications

This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.

Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.

ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.

TRENDnet Technical Support

.

US Canada

Toll Free Telephone: [phone]

24/7 Tech Support

Europe (Germany France Italy Spain Switzerland UK)

Toll Free Telephone: [phone]

English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET

. . . . .

Worldwide

Telephone: +(31) (0) 20 504 05 35

English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET

Product Warranty Registration

Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com

20675 Manhattan Place
Torrance, CA 90501
USA

Copyright ©2006. All Rights Reserved. TRENDnet.