Trend Micro TippingPoint TPS 440T, TippingPoint TPS 2200T User Manual

Install your TPS 440T and 2200T security
devices

This information provides detailed installation instructions for your Threat Protection System (TPS)
440T and 2200T security devices.

Before you begin

Before you begin, go to the TMC at https://tmc.tippingpoint.com, and see the documentation for your
product to:

— Review the product release notes for information about product updates.

— Review the detailed installation and safety documentation for your product.

Important: The 440T and 2200T security devices may require a license update to ensure

sufficient inspection throughput when you connect to your network. For more information, see
“Step 9. Install your license package,” on page 6.

— Make sure the power capacity for your installation meets the documented requirements:

• 440T device: AC Voltage 100 to 240; Current 4 to 2 A; Frequency 47 to 63 Hz

• 2200T device: AC Voltage 100 to 240; Current 12 to 6 A; Frequency 47 to 63 Hz

Warning: Before you turn on power for your product or connect to your network, ensure your

installation meets all power capacity, ventilation, and other safety guidelines. To avoid injury and
damage, you should always review and adhere to all guidelines described in the safety, specification, and
installation documentation. For more information, see the Read Me First document that was included in
your product shipment.

Publication Part Number DOCMT-1016
Edition: August 2017, Rev A1

*DOCMT-1016*

DOCMT-1016

Overview

Your TPS security device ships with the following components:

— A 440T (1U) or 2200T (2U) rack-mountable TPS device with redundant power supplies

— 1 AC power cable (440T device) or 2 AC power cables (2200T device)

— Rack-mounting slide rail kit

— Pre-formatted CFast external storage card

— Null modem cable for the console port

Install and configure your device

To install the device, mount the device in a rack, connect the cables, and then complete the software
setup by using the following steps.

Refer to the following diagram of the chassis front panel when you install and configure the device.

Figure 1. TippingPoint TPS 440T and 2200T security devices – front panel

1. 10 GbE SFP+ ports 5. Dedicated HA port 9. Alert indicator LED

2. 1 GbE SFP ports 6. External ZPHA port 10. Status indicator LED

3. 1 GbE copper ports 7. Console port (top) and Management port (bottom) 11. Power indicator LED

4. External CFast card 8. Power button (440T devices have power switch on back panel)

Step 1. Determine total rack space

Before you install the chassis, determine the total rack space that is required to install your device.

If you plan to expand your security solution to include additional devices in the future, allow space in
the rack for additions.

TippingPoint security devices fit in a 19-inch rack. When you use additional, appropriate accessories,
each device also fits in a 23-inch rack.

2 Install your TPS 440T and 2200T security devices

Step 2. Attach the device to the rack

Unpack the rail kit that shipped with your security appliance and review the installation documentation
on the TMC.

Note: The TPS 440T and 2200T security devices have the following weight values:

— 440T devices: 15.28 pounds (6.93 kilograms)

— 2200T devices: 26.26 pounds (11.91 kilograms)

To prevent bodily injury when mounting or servicing this unit in a rack, take special precautions to
ensure that the device remains stable. When attaching the device to the rack, follow these guidelines.
For other rack-mounting options, refer to the product hardware documentation.

— If the rack comes with stabilizers, install the stabilizers before mounting or servicing the unit in

the rack.

— If the rack is partially filled, load the rack from the bottom to the top with the heaviest

component at the bottom of the rack.

— During the initial installation, keep in mind the weight distribution and stability of the rack.

You can optionally order front mounting ears from TippingPoint to install the devices in two-post
racks in front-mount or mid-mount positions. For more information, contact your TippingPoint
account contact.

Step 3. Connect the power supply

After you have racked your security device, attach the AC power supply connections.

Connect the power

1. Locate the power inlet on the back of the chassis.

2. Plug the female end of a standard power cord into the power inlet and plug the other end of the
power cord into an AC outlet, power strip, or UPS.

The 440T and 2200T security devices require the use of one power cord to turn on the device. For a
2200T security device, use a second power cord for redundancy. For maximum protection, use
different power circuit feeds for each power cord.

Step 4. Insert the CFast card

Install the user disk into the empty slot on the front panel of the device. This pre-formatted,
hot-swappable user disk can store system logs, snapshots, and other system data.

1. Locate the external user disk in the accessory kit.

2. Insert the external user disk into the external user disk slot on the front panel.

3. If the device has been set to require authentication for external user disks, complete the mounting
process by using the command line interface (CLI). For a list of CLI commands that manage the
external user disk, review the documentation for your product on the TMC.

Install your TPS 440T and 2200T security devices 3