Rebated edge under plate
ROUTER TABLE
INSERTPLATE
Large rigid table
insert plate for
incorporation
into user
Will accept screw on style guide
bushes for use as a copy follower.
Integral corner clips to
secure plate to table.
made router
tables.
MOUNTING INSTRUCTIONS
Rout out aperture 280mm x 203mm.
Rebate inner top edge 6.35mm deep and 12.7mm wide to accept insert plate.
1. When mounting a large router, position
it so the handles fit through the opening.
3.The top and front of the Insert Plate is
determined by the location of the lead-on
pin holes. These holes are to the right of the
cutter aperture.
2. Remove router plastic slider base.
4. Centre your existing base plate slider
using the concentric rings, and line up
the mounting holes on the radial lines
(radial lines work with most routers).
Ensure holes in sliding base do not
interfere with lead-on pin holes. Use sticky
tape to hold the plate in position.
6.35mm x 12.7mm
rebate permits
Concentric rings
and radial lines make it easy
to centre the router on the
base plate.
Moulded with slight crown (0.8mm)
on top for distortion free cuts.
mounting in 19mm
tops.
n Rigid 9.5mm thick phenolic plate.
n Supplied with two concentric rings and lead-on pin.
n Can be used with most makes of router.
n Integral corner clips.
n Concentric rings & radial lines on underside for easy
centring of router.
Specification
Insert plate size __________________306mm x 229mm x 9.5mm
Aperture size required
Aperture rebate size required
Aperture corner radius
Suggested table thickness
Max. weight of router
Max. router base dia.
Router cutter aperture
Insert ring apertures
Cutter dia. max.
___________________ 280mm x 203mm
____________ 6.35mm x 12.7mm
___________________________ 6.35mm
__________________________ 19mm
________________________________ 8kg
_____________________________200mm
_____________________________98mm
________________________ 68mm/32mm
_______________________ 94mm/64mm/28mm
Intended Use
The plate is intended to be user drilled to accept a router. Plate is to be
recessed into a user made table top to create a router table. It is to be used
with a back fence, safety top guard, safety top & side pressures,
a no-volt release switch, pushstick and fine height adjuster.
5.
Securely clamp plates together using ‘G’
cramps. Do not use spring clamps because
they do not exert enough pressure and the
parts may move.
7.
Remove clamps, and countersink the holes
from the top. Use a drill stand if available.
9.Fit corner clips and secure plate to table. The corner clips are designed to clamp into
the corner and not to clamp down to the table. Ensure all fixing screws are subflush. Fit
router table safety accessories before use.
Product Ref.
6. Using the correct drill bit diameter, drill
through the plastic slider base. Use a drill
stand if possible to ensure the holes are
accurate.
8.Mount the insert plate to the router using
suitable screws (not included).
RTI/PLATE
Safety
User must be competent in using woodworking equipment
before using our products. Consider working
environment before using tools. Ensure working
Cutter Rotation
position is comfortable and component is held
securely. Please keep children away from tools
and work area. All tools have a residual risk so
must therefore be handled with caution. Please
read all safety instructions supplied with the
Feed Direction
router before use. Only use router cutters to EN847-1/2 standard.
Items Required
Hand tools, clamps, drill, drill & countersink bits, user made table top,
router, rebate cutter and router table safety accessories.
Maintenance
Use only Trend original spare parts and accessories. Regularly clean with
a soft cloth. No additional lubrication is required. After use keep plate in
table top and cover with a dust cover. Product and accessories at the end
of life should be sorted for environmentally friendly recycling.
SPARE PARTS:
Insert 32mm to 68mm
Ref. WP-RTI/01
Insert 68mm to 98mm
Ref. WP-RTI/02
Lead-on Pin
Ref. WP-RTI/03
Corner Clip Fixing Kit
Ref. WP-RTI/04
ACCESSORIES:
Insert Plate Shield
Ref. RTI/SHIELD
Countersink Screw
Fixing Pack
Ref. FIX/KIT/2
Pushstick
Ref. PUSHSTICK/1
Trend Machinery & Cutting Tools Ltd.
Tel: 0044(0)1923 249911
technical@trendm.co.uk
www.trend-uk.com
Manufactured by ROUSSEAU CO.
© 2013 Trend Machinery & Cutting Tools Ltd
PP C/RT/PLATE v2.0
Loading...