Page 1
AIRSHIELD
PRO
AIR CIRCULATING FACE SHIELD
VISOR APPROVAL Z87+ HIGH IMPACT
Please read these instructions before use.
Page 2
AIR/PRO - USA
Dear Customer
Thank you for purchasing this Trend product,
we hope you enjoy many years of creative and
productive use.
Please remember to return your guarantee card
within 28 days of purchase.
CONTENTS
INTRODUCTION ______________________ 1
SUITABILITY FOR USE ________________ 2
APPROVALS ________________________ 3
TECHNICAL DATA ____________________ 3
ELECTRICAL SAFETY ______________ 4 - 5
ADDITIONAL PRECAUTIONS ___________ 6
ITEMS ENCLOSED ____________________ 6
DESCRIPTION OF PARTS ______________ 7
ASSEMBLY, ADJUSTMENT
& OPERATION
- Battery Pack Charging and Installation ____ 8
- Visual Inspection _____________________ 9
- Functional Test ______________________ 9
- Low Battery Warning __________________ 9
- Fitting Procedure ____________________ 10
- Removing Faceshield ________________ 10
- Ear Defender Clips __________________ 10
ACCESSORIES _____________________ 11
MAINTENANCE & CARE ______________ 11
- Routine Checks _____________________ 12
- Storage ___________________________ 12
- Transportation ______________________ 12
REPLACEMENT SPARE PARTS ________ 13
- Battery Pack _______________________ 13
- Air Filter ___________________________ 14
- Face Seal _________________________ 14
- Visor _____________________________ 15
- Headband _________________________ 15
- Visor Overlay _______________________ 15
- Fan Motor Unit _____________________ 16
- Electronics Unit/Switch Housing ________ 16
ENVIRONMENTAL PROTECTION _______ 17
GUARANTEE _______________________ 18
SPARE PARTS ______________________ 19
- Spare Parts List ____________________ 19
- Spare Parts Diagram ________________ 20
For Technical Support
Email: technical@trend-usa.com
INTRODUCTION
The Airshield Pro (AIR/PRO) is a lightweight
powered unit intended for full eye and face
protection from solid dust, impact and chemical
liquid splash.
The Airshield Pro protects the users eyes and
face from small debris such as wood particles or
wood shavings.
The Airshield Pro is powered by a rechargeable
battery pack held inside the unit. Air is filtered
through the unit to provide a constant flow of
clean air over the face. A face seal ensures that
positive pressure is maintained within the unit.
The Airshield Pro has an adjustable headband
and concussion cradle, ensuring a comfortable
fit for most head sizes.
Wide range of applications including woodworking, pottery, craft design and
technology, DIY and building maintenance,
food preparation and processing, fitting and
application of insulation, dental laboratories,
horticulture and pest control.
Read this manual before using the Airshield Pro.
It must be fitted and used in accordance with this
manual to obtain the design performance. Use
as part of your maintenance program.
The following symbols are used throughout this
manual:
Denotes risk of personal injury, loss of
life or damage to the tool in case of nonobservance of the instructions in this
manual.
Denotes risk of electric shock.
Caution
Carefully read through this entire instruction
0DQXDODQGWKHHQWLUHURXWHU2SHUDWRU·V
Manual before using your new AIR/PRO. Pay
close attention to the Safety section and the
Safety Symbols. If you use your AIR/PRO
properly and only for what it is intended, you
will enjoy years of safe, reliable service.
-1-
Page 3
AIR/PRO - USA
SUITABILITY FOR USE
This visor must be used strictly in accordance
with these instructions. Do not use the AIR/PRO
visor for protection against unknown atmospheric
contaminants or when concentrations of
contaminants are unknown or immediately
dangerous to life or health, or in atmospheres
likely to be deficient in oxygen.
Only use this AIR/PRO with the parts and
accessories listed in these instructions.
The AIR/PRO is only for use by trained,
competent personnel. In the power-off state little
or no respiratory protection is to be expected,
and this is considered to be an abnormal
situation.
In the power-off state there will be a rapid build
up of carbon dioxide and depletion of oxygen
may occur.
Without the face seal fitted no respiratory
protection is to be expected. At very high work
rates and peak inhalation the pressure flow in
the device may become negative.
Head Protection: This is NOT an industrial
safety helmet.
Warning
The TREND AIRSHIELD PRO is not a
RESPIRATOR nor a NIOSH approved device.
Using the power visor against harmful
substances may result in sickness or death.
This filter will not protect your lungs against
harmful vapors or toxic fumes. Misuse may
result in sickness or death. For proper use, read
instruction manual.
Use for:
Relief from the bothersome effects of the
common nuisance dusts. Provides limited eye
and face protection. Users must evaluate their
specific eye and face hazards and choose
appropriate protective equipment such as safety
glasses.
Do not use for:
Protection from harmful dusts, mists, fumes or
vapours. Professional/occupational applications
where NIOSH approved respiratory protection is
required.
Ophthalmic spectacles may transmit impacts
from high-speed particles, thus creating a hazard
to the wearer.
Leave the contaminated area immediately if any
of the following conditions apply:
Q The buzzer sounds.
Q Any part of the AIR/PRO becomes damaged.
Q Airflow into the AIR/PRO decreases or stops.
Q Breathing becomes difficult.
Q Dizziness or other physical distress or
irritation occurs.
Q The user tastes or smells contaminants.
Never modify or alter this product, except as
directed in the service tasks contained in these
instructions.
Some fabric parts of the AIR/PRO which
PD\FRPHLQWRFRQWDFWZLWKWKHZHDUHU·VVNLQ
could cause allergic reactions to susceptible
individuals.
Transportation
For transportation purposes use the carry bag
provided and protect the unit from physical or
chemical damage.
Please read the operating instructions
carefully and keep them together with
the AIR/PRO.
Before use fully charge the battery for
24 hours.
Not to be used if the contaminate
is potentially explosive or highly
flammable.
-2-
Page 4
AIR/PRO - USA
APPROVALS
The Trend Airshield Pro has been tested to ANSI
Z87.1 by ICS Laboratories, 1072 Industrial
Parkway, Brunswich, Ohio 44212.
The visor, when fitted to the unit gives protection
as detailed below:ANSI Z87+ HIGH IMPACT
Note that contact of the visor with your skin
will not cause allergic reactions under normal
conditions. It is unlikely that any contact will occur
in normal conditions of use.
The frame is marked:Trend Routing Technology
Airshield
ANSI Z87+ HIGH IMPACT
Size range 6 - 3/8” - 7-3/4”
Year of manufacture
TECHNICAL DATA
Type: Powered AIR/PRO.
This unit does not carry any respiratory
approvals in North America. Record keeping
should be in accordance with OSHA.
Voltage 12V
1
Head size 20
Protection factor Assigned (APF) 20
Motor sound level 70db
Weight: 2.21 lbs nominal
Temperature
range: Charging +41°F to +104°F
Use -23°F to +104°F
Storage +41°F to +104°F
Airflow: Initial 7.06 cf/min
(clean filter, fully charged
battery)
Minimum 5.6 cf/min
Humidity 0-90% storage and use
(Store out of direct sunlight)
/2” to 24 1/2”
Respiratory Protection (Reference Only):
BS EN 12941:1999, respiratory devices, powered
filtering devices class TH2P. For use against solid
particulates only.
Eye Protection:
ANSI Z87+ HIGH IMPACT.
Pressure Storage 80Kpa to 130Kpa
Use 80Kpa to 130Kpa
Battery
Type: Ni-MH
Voltage 3 Cell, nominal 3.6V
Capacity 3.5Ah
Life 8 hours (fully charged
battery pack fitted)
Charging
method/rate Mains Charger
14 hours from fully
discharged.
Weight 0.42 lbs
Charger
Mains voltage: 120V
Consumption 4W nominal
No load output 12VDC
Nominal output 4.2V 300mA
IP20 Indoor use only
EN 60335-1, 60335-2-29
Weight 0.44 lbs
-3-
Page 5
AIR/PRO - USA
ELECTRICAL SAFETY
Power Supply
The charger has been designed for one voltage
only. Always check that the power supply
corresponds to the voltage on the rating plate.
The charger is double insulated.
Never connect to a light socket. Never
connect the live (L) or neutral (N)
wires to the earth pin marked E or .
Safety Instructions for
Battery Charger
Before using charger, read all instructions and
cautionary marking on charger, battery pack, and
AIR/PRO. Only charge your batteries indoors as
the charger is designed for indoor use only.
Q To reduce risk of damage to the charger,
pull by charger body rather than cord when
disconnecting charger from power supply.
Q Make sure cord is located so that it will not
be stepped on, tripped over, or otherwise
subjected to damage or stress.
Q An extension cord should not be used.
Q The charger is ventilated through slots in the
housing. Do not place any object on charger
that might block the ventilation slots and result
in excessive internal heat. Place the charger
in a position away from any heat source.
Q Do not operate charger with damaged cord or
plug - have them replaced immediately.
Q Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way.
Q Do not disassemble charger. Incorrect
reassembly may result in a risk of electric
shock, electrocution or fire.
Q To reduce risk of electric shock, unplug
charger from outlet before attempting any
cleaning. Removing the battery pack will not
reduce this risk.
120 volts present at charging
terminal. Do not probe with
conductive objects. There is a danger
of electric shock.
If battery pack case is cracked or
damaged, do not insert into charger.
There is a danger of electric shock.
Q The charger and battery pack is specially
designed to work together. DO NOT attempt
to charge the battery pack with any other
chargers.
Q Do not expose charger to rain or snow.
Q The charger is not intended for any uses
other than charging AIR/PRO rechargeable
batteries. Any other uses may result in risk of
fire, electric shock or electrocution.
Q NEVER attempt to connect two chargers
together.
Q DO NOT store or use the tool and battery
pack in locations where the temperature
may reach or exceed 104ºF (such as outside
sheds or metal buildings in summer).
Q The charger is designed to operate on
standard household electrical power. Do not
attempt to use it on any other voltage!
Safety Instructions for
Battery Packs
Q The battery pack is not fully charged when first
purchased. First read the safety instructions
below, then follow charging notes and
procedures.
Q Do not incinerate the battery pack even if it is
severely damaged or is completely worn out.
The battery pack can explode in a fire.
-4-
Page 6
AIR/PRO - USA
Q A small leakage of liquid from the battery
pack cells may occur under extreme usage or
temperature conditions. This does not indicate
a failure. However, if the outer seal is broken
and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon
juice or vinegar.
c. If battery liquid gets into your eyes, flush
them with clean water for a minimum of
10 minutes and seek immediate medical
attention.
Q Never attempt to open the battery pack for
any reason. If the plastic housing of the
battery pack breaks or cracks, immediately
discontinue use and do not recharge it.
Q Do not carry extra battery packs in aprons,
pockets, or toolboxes along with metal
objects. Battery pack could be short-circuited
causing damage to the battery pack and
possibly causing severe burns or fire.
3. If charging problems persist, take or
send the tool, battery pack and charger to
your dealer.
Q DO NOT CONTINUE to use if the battery
pack does not charge properly.
Q Always unplug the charger from the power
supply when there is no battery pack fitted.
Unplug charger before attempting to clean.
Q Do not freeze or immerse charger in water or
any other liquid.
Do not allow any liquid to get inside
charger. Electric shock may result.
To facilitate the cooling of the battery
pack after use, avoid placing the
charger or battery pack in a warm
environment such as in a metal shed,
or an un-insulated trailer.
Q Charge the battery packs only in a Trend AIR/
PRO charger.
Q Do not charge the tool in a damp or wet
environment.
Q Longest life and best performance can be
obtained if the battery pack is charged when
the air temperature is between 64.5°F and
75°F. DO NOT charge the battery pack in an
air temperature below 41°F, or above 104°F.
This is important and will prevent serious
damage to the battery pack.
Q The charger and battery pack may become
warm to touch while charging. This is a
normal condition, and does not indicate a
problem.
Q To prevent overheating, do not cover the
charger and do not charge battery packs in
direct sunlight or near heat sources.
Q If the battery pack does not charge properly:-
1. Check the main supply socket by
plugging in a lamp or other appliance.
Never attempt to open the battery
pack for any reason. If the plastic
housing of the battery pack breaks or
cracks, do not use it.
Read all of the instructions in the
battery charger section of this manual
before attempting to charge the
battery pack for the AIR/PRO.
Q Always use correct battery pack (pack
supplied with tool or exact replacement pack).
Never install any other battery pack as it
will damage the AIR/PRO and may create a
hazardous condition.
2. Move charger and battery pack to a
location where the surrounding air
temperature is approximately 64.5°F and
75°F.
-5-
Page 7
AIR/PRO - USA
ADDITIONAL SAFETY
PRECAUTIONS FOR
AIR/PRO
Q Protective Equipment should be stored in a
cool dry place.
Q For adequate protection the AIR/PRO must fit
or be adjusted to the size of the head.
Q DO NOT clean with proprietary cleaning
media or solvents, follow the instruction in
manual.
Q DO NOT apply paint, solvents, adhesives or
self-adhesive labels which are not approved
by Trend.
Q DO NOT use AIR/PRO without filters fitted,
with damaged seals and/or damaged visor.
Q DO NOT use replacement parts except those
supplied by Trend.
Q To maintain the full efficiency of the AIR/PRO,
there must be no alteration to the structure or
LW·VFRPSRQHQWSDUWV
Q Toxic Dusts on the AIR/PRO or filters from
usage should be handled in a safe manner
in accordance with your chemical or material
suppliers instructions. Used filters to be
disposed of safely in the same manner.
ITEMS ENCLOSED
1 x Airshield Pro complete
1 x Airflow indicator
1 x Pair THP2 filters
1 x 8 Hour rechargeable battery
1 x Disposable visor overlay - clear
(may be already fitted)
1 x Battery charger
1 x Pair ear defender clips
(for Trend accessory Ref. AIR/P/6 only)
1 x Carry bag
1 x Instruction manual
1 x Guarantee card
If further information is required with regards to
the AIR/PRO, please contact Trend.
Charge the battery pack before use.
Ensure the AIR/PRO is correctly
assembled with the filter and a fully
charged battery pack.
-6-
Page 8
DESCRIPTION OF PARTS
A. Cover
B. THP2 Filter
C. Battery pack
D. Head cover & face seal
E. Switch and contact assembly
F. Motor
G. Visor lock knob
H. Head band assembly
I. Brow comfort pad
J. Visor
K. Visor overlay
L. Airflow indicator
AIR/PRO - USA
M. Charger
N. Carry bag
O. Ear defender clip
P. Crown strap
Q. Headband knob
-7-
Page 9
AIR/PRO - USA
ASSEMBLY, ADJUSTMENT
& OPERATION
Battery Pack Installation
The AIR/PRO is supplied with one rechargeable
battery pack for eight hours duration.
Battery pack must be initially
charged for 24 hours.
Check that the voltage shown on the charger is
suitable for the mains supply. A thermal fuse
protects the charger against short circuiting and
overloading.
Q Lift the cover by pressing the forward side tabs
inwards and rotating the cover rearwards as
shown below:
Battery Pack Charging
Q Fit the battery charger connector into the rear of
the electronics unit and connect the charger to a
mains AC supply.
Q After charging switch off the mains AC supply,
remove the charger connector from the AIR/PRO.
Battery packs should be initially charged for
24 hours and 14 hours thereafter when fully
discharged. Full working capacity of the battery will
not be achieved until the battery has been through
3 or 4 complete charging cycles. Please note the
light will not extinguish when a full charge has been
achieved.
:KHQSOXJJHGLQWRD¶OLYH·RXWOHWDQGQREDWWHU\
connected LED illuminates as green to show a
live circuit. When connected to an under charged
battery, in helmet or battery cradle, the LED
changes to red. When battery charging is complete,
the LED changes back to green and battery is on a
WULFNOHFKDUJH)URP¶GHDG·WKHFKDUJHUZLOOVWLOOWDNH
about 14 hours (overnight) to fully charge a battery.
Q Slide the battery pack into its housing as shown
below.
The AIR/PRO has a pre-use and low battery audio
signal. Leave the contaminated area if the buzzer
sounds.
Charger must be disconnected from the
mains supply when not in use.
After the charging period, remove the charger from
the AC supply socket.
An accessory external remote battery charger
cradle Ref. AIR/P/7 is also available.
Remote Battery Cradle Accessory
Ref. AIR/P/7
Q Remove battery pack from the AIR/PRO.
Q Fit the charger connector into the socket in the
remote battery cradle. Connect charger to a
mains AC supply.
Q Fit the battery into the cradle. The LED lights
up to red. When charging completed LED will
change to green.
Q Refit cover ensuring tabs lock the cover in
position.
Q After charging of battery, switch off the mains
AC supply, remove the battery from the cradle
and remove charger connector from the cradle.
-8-
Page 10
Visual Inspection
Q Check the face seal material for damage.
Q Check the face seal attachment to the
AIR/PRO chassis and visor.
Q Check the visor seal for damage.
Replace any damaged parts including
scratched or damaged visors.
Functional Test
The purpose of this test is to ensure that the
airflow through the AIR/PRO is in excess of
the minimum design value of 5.6 cubic feet per
minute.
Proceed as follows:
Ensure that the air filters have been installed
correctly as shown.
To fit air flter
AIR/PRO - USA
Hold plastic neck of air filter to fit and
remove. Do not pull on filter.
Q Hold the neck of the fitted air filter and
push firmly toward sealing face to release
from securing tabs and lift filter upwards to
remove. Discard appropriately.
To check the airflow turn the AIR/PRO upside
down and locate the airflow indicator on the four
slots at the front of the AIR/PRO.
Press the red on/off switch to operate the fan.
The red ball is raised to the top of the indicator
tube if the system is operating correctly.
If the red ball is raised to less than half the
height of the tube then either the battery charge
is low or the filters are blocked and need
replacing.
Low Battery Warning
Q Locate new air filter against sealing face.
Push firmly toward sealing face and
downwards. Filter will click in securing tabs.
Q Repeat for other filter.
Q Refit cover.
If an audible regular intemittent tone sounds,
recharge or replace the battery pack.
-9-
Page 11
AIR/PRO - USA
Fitting Procedure
The crown strap has a soft pad that needs to
be removed before adjustment. Adjust the
crown strap length on the headband so that
the headband rests against brow.
Q Crown strap adjustment is made by pulling
the tab out of the strap and placing the pin
into the next suitable hole, once set replace
pad.
Q Adjust headband diameter by pulling out knob
and rotating for head size, push the knob in
to secure as shown.
Ensure face seal is above the ears. Check
that the face seal is taut so that there are no
gaps between mask and face as shown.
Ensure that the face seal around the chin and
sides is pulled away from the frame and visor
and not towards it.
Check the fit of the face seal in a mirror
and/or run a finger around the line of the face
seal to ensure contact.
At very high work rates, the pressure
within the AIR/PRO may momentarily
become negative at peak inhalation.
Vacate the contaminated area
immediately if the airflow is reduced
or stops, or the low battery warning
buzzer sounds.
If protective clothing is worn,
ensure the bottom of the visor is not
obstructed.
Removing Procedure
Switch on the fan/motor by operating the red
on/off switch.
Adjusting the height will affect the fit around
the chin.
Adjusting the face seal will affect the fit at the
sides.
Ensure face seal is above the ears.
Vacate from the contaminated area
before removing the AIR/PRO.
Raise the visor and switch the fan motor off.
Pull out the knob to release headband and lift
the AIR/PRO from the head.
After finishing using the AIR/PRO follow the
maintenance procedure.
Ear Defender Clips
Please refer to instructions supplied with
accessory ref. AIR/P/6 for fitting defender clips
and ear defenders to the AIR/PRO.
-10-
Page 12
ACCESSORIES
Please use only Trend original accessories.
Ref. AIR/P/1 THP2 filter pack (pair)
Ref. AIR/P/3C Visor overlay - clear
(pack of ten)
Ref. AIR/P/4 8 hour battery
Ref. AIR/P/5/L/USA 120V charger
Ref. AIR/P/6 Ear defenders (pair)
Ref. AIR/P/7 Remote battery
charger cradle
Ref. AIR/WIPE Airwipes (100 wipes)
Ref. WP-AIR/05/USA Sweatband available
for users with smaller
craniums.
AIR/PRO - USA
Do not immerse the AIR/PRO in water or any
other fluids.
Do not use organic solvents or abusive
cleaning agents on any part of the the
equipment.
After cleaning carry out the functional test.
Gamma sterilisation is effective
but causes embrittlement of plastic
components and is not recommended.
Replace if deficient after the following checks.
1. Excessive abrasion and scratches on the
visor.
2. The face seal for its seal to the visor and for
holes.
3. Fit and fastenings to the headband.
MAINTENANCE AND CARE
AIR/PRO Cleaning
After using the AIR/PRO follow the procedure
below:
AIR/PRO should not be cleaned with
compressed air, solvents, sterilising
by heat or autoclaving, as this will
cause damage.
Precautions are to be taken to
prevent inhalation of harmful dust
or contaminant on the surface or
retained on the filters.
Carefully remove bulk contamination from the
AIR/PRO and wipe down with a damp cloth
containing a mild detergent solution.
Clean and sterilise all parts by wiping down
the visor, face seal and headband with visor
wipes (ref. AIR/WIPE)
(Sodium Hypochlorite or Ethylene Oxide Gas
have also been proved effective).
Scratched or damaged visor may not
offer full protection and therefore
should be replaced.
Specific Instructions for Cleaning
and Disinfection of Visor
Clean with a damp cloth – do not use
hydrocarbons, chemicals, cleaning fluids or
solvents on the visor. If necessary, a mild
solution of washing-up liquid and warm water
may be used.
Charger Cleaning
Dirt and grease may be removed from the
exterior of the charger using a cloth or soft
non-metallic brush. Do not use water or any
cleaning solutions.
Disconnect the charger from the AC
outlet before cleaning.
Lubrication
Your AIR/PRO requires no additional
lubrication.
-11-
Page 13
AIR/PRO - USA
Routine Checks
The expected life of the visor is approximately 3
years if well maintained and cleaned. (Care must
be taken not to scratch the visor).
This manual contains relevant guidance on
routine maintenance; however, you may wish
to introduce additional checks as required by
OSHA. The following table shows the frequency
of these checks.
Operation Frequency
Clean Internally and Externally Daily
Visual Inspection Daily
Charge Battery Pack/Packs Daily
Functional Test* Daily, Weekly and Monthly
* Remarks: Dust from wood, grain and cement
may require more frequent replacement of the
filter. No filter should be left in the hood/helmet
for more than 1 month if in daily use or 3 months
if used infrequently.
Storage
Q The AIR/PRO should be placed in the carry
bag, stored within a temperature range of
41°F to 104°F and out of direct sunlight.
Q Replacement filters are to be left in air sealed
bags and expiry dates to be checked
regularly.
Transportation
Q The complete AIR/PRO should be
transported in the carry bag provided. Good
quality commercial packing should be used.
Symptom Cause Remedy
Reduced Cover air holes blocked Clear air flows
Airflow
Filters clogged Fit a new filter
Battery flat Recharge battery or fit recharged
battery pack
No airflow Unit switched OFF Press switch to ON
Switch faulty Replace switch housing
Battery pack not fitted Fit a fully charged battery pack
Battery pack discharged Fit a fully charged battery pack
Fan-motor unit failure Fit a replacement fan-motor unit
-12-
Page 14
AIR/PRO - USA
REPLACEMENT OF SPARE
PARTS
Replacement parts and accessories supplied
by Trend should only be used. The use of
accessories not supplied by Trend will not
be guaranteed and invalidate such National
approvals as held by Trend. Modifications to the
AIR/PRO will make the approvals invalid and the
use illegal under National Laws and Guidance.
Trend replacement parts and accessories, must
only be used with the AIR/PRO.
Battery Pack
Q Lift the cover by pressing the forward side
tabs inwards and rotating the cover rearwards
as shown below.
Q Slide the battery pack out of its housing.
Q Replace with new battery.
Q Refit cover ensuring tabs lock the cover in
position.
-13-
Page 15
AIR/PRO - USA
Air Filter
Q To replace air filter, lift the cover as shown.
Q Hold the neck of the fitted air filter and push
firmly towards sealing face to release from
securing tabs and lift filter upwards to remove.
Discard appropriately.
Face Seal
Replace the face seal as shown.
Q Starting from the center of the visor, pop up
studs on face seal. Release from front of
helmet.
Q Unfasten the crown strap on the headband
and release elastic loops on each side.
Q Locate new air filter against sealing face.
Push firmly toward sealing face and
downwards. Filter will click in securing tabs.
Q Repeat for other filter.
Q Refit cover
Precautions are to be taken to
prevent inhalation of harmful dust
or contaminant on the surface or
retained on the filter and inside the
cover.
Q Pull face seal over the headband knob and
remove face seal from AIR/PRO.
Q Tuck edge strip of new face seal under
headband and secure and close tape of AIR/
PRO. Slip the elastic loops over headband
knob and secure to visor pop studs.
Face seals should be stored out of direct
sunlight and replaced at least every 5 years.
-14-
Page 16
AIR/PRO - USA
Visor
Q Remove the seven face seal pop studs from
visor.
Q Replace the old or damaged visor assembly
as shown.
Headband
Remove face seal and visor as shown.
Install a new headband assembly as shown.
2
1
Q Release nuts and push screws inwards,
release the front tab and lift visor from the
helmet.
Q Fit replacement visor ensuring slot in visor
locates on tab and bottom edge in grooves,
secure with screws and nuts.
Q Fit visor stiffener wire. Insert the wire ends
into the outer slots provided and rotate to
engage securely in the center slot.
Q Visors should be stored out of direct sunlight
and replaced at least every 5 years.
3
Q Release nuts and screw and remove the
headband from the helmet.
Q Assemble anti-rotating cap and screw retainer
to headband noting that anti-rotating caps are
PDUNHG¶/·OHIWDQG¶5·ULJKW
Q Position the headband in the helmet ensuring
that the tabs on the anti-rotating cap locate in
the helmet.
Q Fit screws through retainer, anti-rotating cap
and visor secure with nuts.
Visor Overlay
Q Peel away visor protector and ensure visor
surface is clean.
Q Peel the backing paper from adhesive strips
on replacement visor protector. Position
centrally onto visor surface, press down
adhesive strips and remove protective paper.
-15-
Page 17
AIR/PRO - USA
Fan-Motor Unit
Lift the cover. Replace fan/motor assembly as
shown below:
Electronics Unit / Switch Housing
Lift the cover and replace the electronics unit as
shown below.
Q Disconnect fan/motor electrical lead from the
electronics unit.
Q Remove the two screws securing the front air
duct. Lift the air duct from locating lip and pull
fan/motor from rear air duct. Separate fan/
motor from front air duct.
Q Fold back both seals on replacement fan/
motor assembly. With electrical lead point
downwards locate with front air duct and
secure by unfolding seal over duct.
Q Connect electrical lead to electronics unit.
Q Locate front air duct in lip and fan/motor with
rear air duct, tuck excess cable under fan/
motor unit and unfold seal to secure. Secure
air duct with screws.
Q Ensure both seals are fully engaged with
ducts and are fully unfolded, failure to do so
may compromise the units performance.
-16-
Page 18
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
as waste.
Accessories and packaging should be sorted for
environmentally-friendly recycling.
Separate collection. This product
must not be disposed of with normal
household waste.
Rechargeable Batteries and the
Environment
This unit uses Nickel-Metal Hydride
(Ni-MH) batteries. When the battery
pack needs replacing, we recommend
Ni-MH
Discharge the energy from the batteries by
running the batteries down completely, and then
remove them from the AIR/PRO.
the following:-
AIR/PRO - USA
Ni-MH cells are recyclable.
DO NOT THROW THEM AWAY WITH YOUR
HOUSEHOLD WASTE.
They may end up in an incinerator or landfill,
which must be avoided.
Instead, take the batteries to a Trend Service
Agent, your local distributor or a local recycling
station. If necessary, contact your local
municipality for disposal information. The
collected batteries will be disposed of properly
and/or used for recycling purposes.
GUARANTEE
7KHXQLWFDUULHVDPDQXIDFWXUHU·VJXDUDQWHHLQ
accordance with the conditions on the enclosed
guarantee registration card.
-17-
Page 19
Please use only Trend original spare parts.
AIR/PRO - USA
AIR/PRO USA - SPARE PARTS LIST
V3.0 06/2014
No. Qty Desc. Ref.
1 1 Fan/Motor WP-AIR/P/01
2 1 Airflow Indicator WP-AIR/P/02
3 1 Head Cover & Face Seal WP-AIR/P/03
4 1 Head Band WP-AIR/P/04
5 1 Switch & Contact Assembly WP-AIR/P/05
6 1 Carry Bag WP-AIR/P/06
7 1 Visor WP-AIR/P/07
8 1 Cover WP-AIR/P/08
9 - - 10 1 Headband Comfort Pad WP-AIR/P/10
11 2 Pivot Pin Body WP-AIR/P/11
12 2 Pivot Pin Bolt WP-AIR/P/12
13 1 Anti-Rotating Caps (Pair) WP-AIR/P/13
14 2 Knob WP-AIR/P/14
15 1 Ear Defender Clip (Pair) WP-AIR/P/15
16 1 Head Band Fixing Kit (Pair) WP-AIR/P/16
17 1 Head Band Top Frame Comfort Pad WP-AIR/P/17
18 1 THP2 Filter Pack (Pair) AIR/P/1
19 0 Visor Overlay - Clear (Pack of 10) AIR/P/3C
20 1 8 Hour Battery AIR/P/4
21 1 Charger 120V USA AIR/5L/USA
22 1 Manual USA MANU/AIR/PRO/U
-18-
Page 20
AIR/PRO - USA
AIR/PRO USA - SPA RTS DIAGRAM
V3.0 06/2014
-19-
Page 21
NOTES
AIR/PRO - USA
-20-
Page 22
MANU/AIR/PRO/U v3.0
© Copyright Trend 2014. No part of this publication may be reproduced, stored or transmitted in any form without prior permission.
Our policy of continuous improvement means that specifications may change without notice. Trend Machinery and Cutting Tools
cannot be held liable for any material rendered unusable or any form of consequential loss. E&OE
Trend Routing Technology Inc.
7351 West Friendly Avenue,
Suite A, Greensboro, NC 27410
Tel: (877) 918-7363
RECYCLABLE
technical@trend-usa.com
www.trend-usa.com
®
All trademarks acknowledged.
Loading...