Trek 2200 User Manual
Model 2200 Series
High-Voltage 40 Watt Amplifiers
Deliver Cost-Effective High-Performance in
Piezo, MEMS & Other Applications
The first three models in Trek’s 40 watt high-voltage amplifier series – Models 2205, 2210, and 2220 – offer a winning
combination of high performance, exceptional reliability, and other value-added features at an attractive price.
The 2200 Series addresses the market need for cost-effective high-voltage amplifiers which deliver reliable, robust
performance in piezoelectric, electro-optic, MEMS and many other applications.
Industries that will benefit from the advancements enabled by these high-voltage amplifiers are diverse and include
aerospace, biotechnology, defense, military, power, R&D, semiconductors, and electronics.
Performance Specifications Include*:
! Output Voltage Ranges:
±500 V, ±1 kV, ±2 kV
! Output Current Ranges:
±80 mA, ±40 mA, ±20 mA peak AC
! Large Signal Bandwidth:
75 kHz, 40 kHz, 7.5 kHz
Added-Value Features Include:
! 2-year Warranty
! CE Marked
! RoHS Compliant
Trek 2200 Series: Models 2205, 2210 and 2220
As with all Trek amplifiers, the 2200 Series provides:
! DC stability
! Wide bandwidth
! Well-regulated and controlled AC output signals
! Full four-quadrant, class AB, all-solid-state output stages
The four-quadrant, active output stage sinks or sources current into reactive or resistive loads throughout the
output voltage range. This is essential for achieving the accurate output response and high slew rates
demanded by reactive loads.
In addition, the models in the 2200 Series provide:
! DC offset adjustment with front panel metering
! A unique auto-recovery shutdown feature for protection from overpowering the output
! HALT Tested
* See page 2 for specifications per model
TREK, INC. • 190 Walnut Street • Lockport, NY 14094• USA • 800-FOR TREK
(fax) • www.trekinc.com • sales@trekinc.com 716-438-7555 • 716-201-1804
Model 2200 Series Specifications
0
0.5
1
1.5
2
2.5
3
3.5
4
1 10 100 1000 10000 100000
0.1uF
10000pF
1000pF
500pF
100pF
noload
Model 2220
Power Supply Trip off Points
(with auto recovery)
KVp-p
Frequency (Hz)
Model 10/40A Specifications
All specifications are with no load unless otherwise noted.
PARAMETER:
Output Voltage Range
Output Current Range
Input Voltage Range
DC Voltage Gain
(Accuracy)
Output Noise
Slew Rate (10% to 90%,
typical)
Large Signal
Bandwidth (-3dB)*
Model 2205
500V0 to ±
0 to ±40 mA DC
0 to ±80 mA peak AC
(for 5 ms minimum)
0 to ±10 V DC or peak AC
50 V/V
(Better than 0.5% of full scale)
Less than 25 mV rms.
Greater than 150 V/µs
DC to 75 kHz
Model 2210
1 kV0 to ±
0 to ±20 mA DC
0 to ±40 mA peak AC
(for 5 ms minimum)
0 to ±10 V DC or peak AC
100 V/V
(Better than 0.5% of full scale)
Less than 30 mV rms.
Greater than 150 V/µs
DC to 40 kHz
Model 2220
2 kV0 to ±
0 to ±10 mA DC.
0 to ±20 mA peak AC
(for 5 ms minimum)
0 to ±10 V DC or peak AC
200 V/V
(Better than 0.5% of full scale)
Less than 50 mV rms.
Greater than 100 V/µs
DC to 7.5 kHz
(minimum trip off frequency)
Small Signal
Bandwidth (-3dB)
Stability
Drift with Time
Drift with Temp.
Voltage
Scale Factor
Monitor
DC Accuracy
Current
Monitor
*Large Signal Bandwidth, Square Wave Response and Output Noise are optimized using the “Response” adjustment on the front panel of the amplifier
Scale Factor
DC Accuracy
DC to 100 kHz
Less than 300 ppm/hr,
noncumulative
Less than 180 ppm/°C
1/50th of the high-voltage
output
Better than 0.5% of full scale
0.1 V/mA
Better than 2% of full scale
DC to 100 kHz
Less than 300 ppm/hr,
noncumulative
Less than 180 ppm/°C
1/100th of the high-voltage
output
Better than 0.5% of full scale
0.2 V/mA
Better than 2% of full scale
DC to 50 kHz
Less than 300 ppm/hr,
noncumulative
Less than 180 ppm/°C
1/200th of the high-voltage
output
Better than 0.5% of full scale
0.4 V/mA
Better than 2% of full scale
Amplitude vs Frequency Graphs
KVp-pKVp-p
Measurement and Power Solutions
www.trekinc.com
Model 2210Model 2205
Frequency (Hz)Frequency (Hz)
TM
Copyright ã 2012 TREK, INC. All specifications are subject to change. 1244/JRB
Loading...