Treasure Cove Vibra-Tector 740 Quick Start Manual

Thank you for choosing the Vibra-Tector 740
metal detector made by Treasure Products, Inc.

The unique sealed design allows detecting in any
environment including grass, mud, dirt, sand,
black sand, or even in fresh or salt water to a

depth of 100 feet (30 meters).

Pulse Induction Metal Detector

Product Features

Communicates with vibration & light

When a target is located the Vibra-Tector 740

signals with pulses of vibration and flashes of

bright light from a white LED.

Pulse Induction Technology (PI)

A specialized type of detection technology that
allows hunting in salt water or in any type of soil,

including black sand.

Detection depth stability

Advanced electronic circuitry maintains detection

distance throughout the life of the battery.

Target distancing

As you get closer to the target the pulses of
vibration and light will increase in quantity.

Automatic tuning

The state-of-the-art microprocessor controlled
design requires no adjustments of any kind.

Waterproof to 100 ft (30m)

The detectors sealed design allows hunting in the

rain or under water to a depth of 100 feet.

Battery Installation

Understanding the Compartment Seal

This detector uses a compression plug to seal the
battery compartment. When the knob of the seal
is rotated clockwise, the rubber in the plug
expands and presses against the inside wall of

the battery compartment, sealing the unit.

Opening the compartment

To open the battery compartment seal, rotate the

knob counter-clockwise a few turns, then pull to
remove.

Connecting battery

Connect a standard 9-volt battery to the battery

clip and insert the battery into the detector, clip

side first.

Sealing the compartment

To replace the seal, insert all the way in. Then
turn the knob clockwise until hand tight to assure

a water-tight seal.

Before submerging detector make sure

the battery compartment seal is secure.

Operating Instructions

Power on

Hold unit with the search coil up. Light will flash.
Two short pulses of vibration, and a steady dim

light, indicate unit is on.

Power off

After use, hold unit with the search coil up. Light will
flash. Two long pulses of vibration, and no light,

indicate the unit is off.

Low battery auto-off

When the battery is low the unit will shut down

automatically indicated by four long pulses of

vibration and bright light.

Detecting a Target

The Vibra-Tector communicates through pulses

of vibration and bright light. These pulses
increase in quantity the closer the search coil is

to a detected target.

The quantity of pulses is proportional to the target
size and distance. The bigger the target, or the

closer the search coil is to the target, the higher

the pulse count.

Movement of the search coil is required to detect
a target. Sweep the search coil back and forth

along the surface you are searching.

The detector communicates its proximity to the
target only one time per detection. Move the coil

slightly away and then re-approach the target to
get the next detection.

Made in USA

Treasure Products Inc.

www.TreasureProducts.com

Vibra is a registered trademark of Treasure Products Inc.

Use only high quality batteries such as

alkaline or nickel metal hydride (NiMH).

740

Vibra-Tector

Continued on back

Important Notes

• The detection field projected resembles a cone
shape, with the deepest depth of detection in the
center of the coil. The slower the sweep the
deeper the detection depth.

• Raising the detectors coil up while in use will

start the turn-off sequence, indicated by a

blinking light. Lower the detectors coil within 3
seconds to continue detecting.

• Unit will not detect when the light is blinking in

either the turn-on or turn-off sequence.

• As with any new detector you should practice
with known targets to develop your searching
technique.

Helpful Hints

• If you continue to hold the detector with the coil
up after turn on, then the detector will remain on
indefinitely in this vertical position. This feature
may be useful if searching with the detectors coil
in a vertical position is necessary.

• You can secure the Vibra-Tector to your wrist

using the attached wrist strap. To adjust fit, press
down on the cord lock button and move it to the
desired location.

Product Care

• Your Vibra-Tector 740 is a sensitive electronic

instrument. Although it is rugged, care in
transporting and handling will extend its life and
result in optimum performance.

• When the Vibra-Tector is off there is no drain

on the battery. However, if stored for long
periods of time, we recommend that the battery
be removed to prevent damage to the detector
due to a potential battery leak.

VIBRA-TECTOR 740 SPECIFICATIONS

• Manufacturer: Treasure Products

• Model: Vibra-Tector 740

• Detection Type: Pulse Induction

• Search Mode: All metal

• Communication: Vibration and Light

• Tuning: Automatic

• Waterproof: Up to 100 feet (30m)

• Overall Length: 17 inches (43 cm)

• Coil Diameter: 4 inch (10 cm)

• Weight: 1 lb. (450 grams)

• Power Source: One standard 9-volt

• Wrist Strap: Included

• 9-volt Battery: Included

• Warranty Period: 1 year

• Origin: Made in the USA

Specifications and features are subject to

change without prior notification.

Limited Warranty

What does this warranty cover?

Treasure Products warrants that its products are free
from defects in material and workmanship under
normal use for a period of one (1) year from the date
of purchase. Warranty extends only to original

purchaser and is not transferable.

What is not covered by this warranty?

This warranty does not cover any accessories, or any
consumables, as to which there shall be no warranty
or replacement. This warranty does not cover

conditions or damages caused by accidents,

alterations or misuse. In addition, damage due to

normal wear and tear is not covered by this warranty.

What is needed to keep the warranty in service?

You must provide proof of purchase as a condition of
receiving warranty service. Your dated sales receipt,
showing the date of purchase of your product is your

proof of the purchase date.

What will be done to correct the problem?

Treasure Products will repair or replace, at Treasure
Products’ sole discretion, any defective,

nonconforming, or malfunctioning product or any

component thereof.

How do you get service?

If you require warranty service, contact Treasure
Products prior to sending your product in for service.
You can find contact information on our website at

www.treasureproducts.com > support > contact.

This limited warranty gives you specific legal rights,
and you may also have other rights which vary from

state to state.

• • •

• If the detector has been exposed to salt water

always rinse with fresh water and check the
battery compartment for any leaks. If water has
entered the battery compartment carefully wipe
dry and leave open until completely dry.

Other Equipment by Treasure Products, Inc.

Vibra-Probe - Pinpointer Metal Detector

Vibra-Quatic - Pinpointer Metal Detector

E-Z Swing - Metal Detector Harness

© 2002-2020 Treasure Products Inc.

All rights reserved. Made in USA.

Designed and manufactured by Treasure Products.

Vibra is a registered trademark of Treasure Products.

012020A3