Treasure Cove Vibra-Probe 570 Quick Start Manual

TREASURE

PRODUCTS

TM

detectors with a pulse

TM

Vibra-Probe 570

Pinpointer Metal Detector

BA TTER Y INSTALLATION

Uses one standard 9v battery. To install rotate the rear
knob counter-clockwise a few turns and remove the battery
compartment compression seal.

Connect the battery to the battery clip. Insert the battery
into the detector, clip side first.

Replace seal and hand tighten turning clockwise until snug
to secure in place and assure a watertight seal.

IMPORT ANT NOTES

The probe communicates its proximity to the target only
one time per detection. Move the probe tip slightly away
and then re-approach the target to get the next detection.

As with any new detector you should practice with known
targets to develop your technique.

The Vibra-Probe is a robust unit that allows you to probe
the soil; however, it should not be used as a pry-bar or
digging tool.

Thank you for choosing the Vibra-Probe 570 Pinpointer
metal detector made by Treasure Products.

The Vibra-Probe 570 Pinpointer metal detector is a minia­ture version of your primary detector. The modern elec­tronics and simple to use design makes locating elusive
targets easy in any environment including grass, mud, dirt,
sand, black sand, or even in fresh or salt water.

PRODUCT FEATURES

• Communicates with vibration - The Vibra-Probe sig-

nals with pulses of vibration when a target is located.

• Pulse Induction Technology (PI) - Allows hunting in
salt water or in any type of soil, including black sand.

• Detection depth stability - New advanced circuitry main­tains detection distance throughout the life of the battery .

• True target direction - The Vibra-Probe detects at the
tip only, not along the shaf t, enabling precision target pin­pointing.

• Target distancing - The pulses of vibration will con­tinue to increase in quantity as the probe tip gets closer
to the target.

• Automatic tuning - The state of the art microproces­sor controlled design requires no adjustments of any kind.

• Automatic On/Off - Unit automatically turns on when
pointed upward and automatically turns off one minute
after last pulse.

• Waterproof - Sealed design allows hunting in the rain
or even under water to a depth of 30 feet.

Treasure Products, Inc.

1464 Madera Rd. #N195, Simi Valley, CA 93065

Visit us online at www.treasureproducts.com

Always use high quality batteries
such as alkaline or nickel metal
hydride (NiMH) in this detector.

OPERATING INSTRUCTIONS

Turn on: Point the tip upward for at least one second.

Two short pulses of vibration indicates the probe is on.
T urn off: Automatically occurs one minute after last pulse.

Turn off is indicated by two long pulses of vibration.
Low battery turn off: When the battery is low the unit will

shut down automatically indicated by four long pulses.
Operation: The Vibra-Probe 570 communicates through

pulses of vibration. These pulses of vibrations increase in
quantity the closer the probes tip is to the target.

The quantity of pulses is proportional to the targets size
and distance. The bigger the size of the target, or the closer
the probes tip is to the target, the higher the pulse count.

The Vibra-Probe 570 detects targets at the tip only, not
along the shaft. This allows you to precisely locate the
target.

Probe the soil forward and back in different locations until
you detect the target. A pulse of vibration signals a target
detection. As you get closer to the target the number of
pulses increases.

Other fine products from Treasure Products, Inc.

Vibra-PhoneTM 280

Hearing impaired?
Don’t like headphones?
Replace sound with vibration.

Vibra-TectorTM 730

Pulse Induction Metal Detector

• Signals with vibration and light

• Waterproof - Submersible

• Great for divers!

False pulses of vibration may occur if the head of your
primary detector is to close to the area you are probing.

HELPFUL HINTS

If your primary detector signals the target is near the sur­face, probe the surface area before digging. To locate
deeper targets loosen the ground with a suitable digging
tool before using the probe.

When hunting in a lawn, rather then digging a large hole,
insert a screwdriver or similar tool into the ground from
several angles to push the grass and roots aside to form
a slot large enough to insert the probe. Then probe the
sides of the slot to locate the target.

CARE AND MAINTANANCE

Your Vibra-Probe is a sensitive electronic instrument. Al­though it is built to be rugged, care in transporting and
handling will extend its life and result in optimum operat­ing performance.

When the Vibra-Probe is in the off position there is no
drain on the battery. However, for very long periods of
storage, we recommend you remove the battery from the
battery compartment to prevent damage to the detector
due to potential battery leak.

Before submerging the Vibra-Probe
make sure the battery compartment
seal is snug and secured in place.

E-Z Swing

Arms and shoulders tired from
swinging that heavy detector?

That’s why we created the

EZ-SWING Harness.

TM

• Fully adjustable

PRODUCT SPECIFICATIONS

Detection Type • Pulse Induction

Search Mode • All metal

Overall Length • 14 inches

Weight • 0.5 lbs.

Power • Standard 9 volt battery

Warranty • 1 year

Battery • Included

All specifications are subject to change without notice.

TREASURE PRODUCTS LIMITED WARRANTY

What does this warranty cover?

Treasure Products warrants that its products are free from de­fects in material and workmanship under normal use for a period
of one (1) year from the date of purchase.

This warranty extends only to the original purchaser and is not
transferable.

What is not covered by this warranty?

This warranty does not cover any accessories, or any
consumables, as to which there shall be no warranty or replace­ment. This warranty does not cover conditions or damages caused
by accidents, alterations or misuse. In addition, normal wear and
tear are not covered by this warranty.

What to do to keep the warranty in service?

Your dated sales receipt, showing the date of purchase of your
product is your proof of the purchase date. Y ou must provide proof
of purchase as a condition of receiving warranty service.

What will Treasure Products do to correct problems?

Treasure Products will repair or replace, at Treasure Products’
sole discretion, any defective, nonconforming, or malfunctioning
product or any component thereof.

How do you get service?

If you require warranty service, call Treasure Products, Inc. at
[phone] to speak with a Treasure Products technical sup­port representative or email us at [e-mail]
prior to sending your unit in for service.

This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.

©2008 Treasure Products, Inc. All rights reserved.

Designed and Manufactured by Treasure Products, Inc.

80311-01A

Made in the USA