Page 1
DVS GSR Ember-Fyre Burner
Installation Instructions (SKU 96900102)
Compatibility
DVS GSR NB Insert
DVS GS (AU) Inbuilt
Packing List
DVS Ember-Fyre Burner Assembly
Left and Right Ember Trays
8-Piece Log Set
Bag of Rock Wool
Bag of Log Embers
Burner Installation
1. Access the firebox.
2. Install the burner as shown below (make sure the burner is fully seated over the orifices and pushed
all the way to the right). Install the side ember trays.
Page 1 of 6 17601693.docx — 7/12/12 © Travis Industries, Inc.
Page 2
DVS GSR Ember-Fyre Burner
Installation Instructions (SKU 96900102)
Log Set Installation
! The logs are fragile, especially after being exposed to heat.
Make sure the gas control valve is “OFF” and the heater is cool prior to conducting service.
Failure to position the parts in accordance with these diagrams or failure to use only parts
specifically approved with this appliance may result in property damage or personal injury.
If using propane (LP), convert the appliance before installing the burner and logs.
The burner must be correctly positioned before installing the logs. Make sure the burner is fully
seated and the pilot is properly aligned.
Ember Placement
Place a layer of embers along any visible edges of the burner.
Rear Log Placement
The rear log has two holes on the bottom. Place the log so the pins on the burner insert into the
holes on the log (see photos below).
Page 2 of 6 17601693.docx — 7/12/12 © Travis Industries, Inc.
Page 3
DVS GSR Ember-Fyre Burner
Installation Instructions (SKU 96900102)
Left Log Placement
The left log has two holes on the bottom. Place the log so the pin on the burner and the metal
bracket insert into the holes on the log (see photos below).
Right Log Placement
The right log has two holes on the bottom. Place the log so both burner pins insert into the holes on
the log (see photos below). Make sure the log is pushed back so it sits flat.
Page 3 of 6 17601693.docx — 7/12/12 © Travis Industries, Inc.
Page 4
DVS GSR Ember-Fyre Burner
Installation Instructions (SKU 96900102)
Right Twig Placement
The right twig has a single hole in the bottom that fits over the right pin on the back log (see photos
below). The lower side of the twig rests on the right log. Place the twig as shown below.
Left Twig Placement
The left twig has two holes in the bottom of it – for this model, place the log so the left pin on the
rear log inserts into the lower hole (see photo below). The bottom of the log rests on the left log.
Place the log as shown below.
Page 4 of 6 17601693.docx — 7/12/12 © Travis Industries, Inc.
Page 5
DVS GSR Ember-Fyre Burner
Installation Instructions (SKU 96900102)
Front Ember Chunk Placement
This log set includes left, right, and center ember chunks (see photo below).
Left Ember Chunk Right Ember Chunk Center Ember Chunk
Place the ember chunks as shown in the photos below. Make sure the ember chunks do not cover
any burner holes.
Right Side Ember Chunk
Left Side Ember Chunk
Center Ember Chunk
Page 5 of 6 17601693.docx — 7/12/12 © Travis Industries, Inc.
Page 6
DVS GSR Ember-Fyre Burner
Installation Instructions (SKU 96900102)
Rockwool Installation
The included rock wool is placed on top of the burner to enhance the glow from the burner. The rock
wool works best when it is applied in a very thin, porous layer. The best method for applying the
rock wool is to brush it on to the burner. Compress a clump of rockwool between your thumb and
forefinger. Use a stiff brush to apply a thin layer of rockwool fibers onto the burner. Do not use the
entire bag of rockwool. Use only a small amount and save the remainder. Over-use of rockwool will
diminish the glow and may cause sooting or other adverse conditions.
The completed installation is shown below.
Page 6 of 6 17601693.docx — 7/12/12 © Travis Industries, Inc.
Loading...