
Project Quantity Item #
Model Specified: CSI Section 11400
Reach-In Fast Freezer Models/
One, Two & Three Section Reach-In Models - 32" Deep
1-Section Full Length Door Model RFF132WUT-FHS
2-Section Full Length Door Model RFF232WUT-FHS
R
SERIES
Stainless Exterior
& Interior
The R-Series Fast Freezer line is designed to allow on premise, smallscale fast freezing. To accomplish this, a -20 degree F air temperature
is utilized, along with sufficient air movement to promote rapid heat transfer from the product. These models are supplied standard with all the
Traulsen top of the line features, such as balanced refrigeration systems, next generation INTELA-TRAUL® controls and stainless steel
exteriors and interiors.
3-Section Full Length Door Model RFF332NUT-FHS
1-Section Half Length Door Model RFF132WUT-HHS
2-Section Half Length Door Model RFF232WUT-HHS
3-Section Half Length Door Model RFF332NUT-HHS
INTELA-TRAUL
Equipped!
Self-Contained
®
Model RFF232WUT-FHS
Standard Product Features
• Stainless Steel Exterior & Interior
• INTELA-TRAUL® Microprocessor Control System
• Balanced, Self-Contained Refrigeration System Using
R-404A Refrigerant
• Full or Half Length Stainless Steel Doors With Locks
• Self-Closing Doors With Stay Open Feature At 120 Degrees
• Guaranteed For Life Cam-Lift Hinges
• Guaranteed For Life Horizontal Work Flow Door Handle
• Standard Door Hinging: 132W = Right, 232W = Left/Right,
332N = Left/Right/Right (other hingings available)
• Automatically Activated Incandescent Lights
• Stainless Steel Breaker Caps
• Three Chrome Plated Adjustable Shelves Per Section,
Supported On Shelf Pins (installed at the factory)
• Automatic Bottom Mounted Electric Condensate Evaporator
• Magnetic Snap-In Door Gaskets
• Gasket Protecting Stainless Steel Door Liner
• Controllable Anti-Condensate Door Perimeter Heaters
• Thermostatic Expansion Valve Metering Device
• Stainless Steel One-Piece Louver Assembly
• 9' Cord & Plug Attached (one section models only)
• Set of Four (4) 6" High Adjustable Stainless Steel Legs
• One Year Parts And Labor Warranty
• Two Year Control Warranty (parts and labor)
• Five Year Compressor Warranty
Options & Accessories
• Stainless Steel Finished Back With Rear Louvers
• Re-Hinging Feature For Door(s)
• No. 1 Type Tray Slides To Accommodate either (1) 18" x 26"
or (2) 14" x 18" Sheet Pans, Adjustable To 2" O.C.
• No. 2 Type Tray Slides To Accommodate (1) 18" x 26" Sheet
Pans, Adjustable To 2" O.C.
• No. 3 Type Tray Slides To Accommodate (2) 12" x 20" Steam
Table Pans, Adjustable To 2" O.C.
• No. 4 Type Tray Slides To Accommodate (1) 18" x 26" Sheet
Pans (chrome rod type, equips 1/2 section)
• Universal Type Tray Slides To Accommodate Either (1)
18" x 26" or (2) 14" x 18" Sheet Pans, or (2) 12" x 20" Steam
Table Pans, Adjustable To 4" O.C.
• Additional Chrome Plated Shelves
• Locking Hasps (padlocks supplied by others)
• Stainless Steel Shelves In Lieu of Standard Chrome Plated
• Kool Klad Exterior Laminate Decor
• Set of Four (4) 6" High Casters In Lieu of Legs
• Set of Four (4) 4-5/8" High Casters In Lieu of Legs
• 4-1/2" High Stainless Steel Base In Lieu of Legs
• 6" High Stainless Steel Kickplate (for use with standard legs)
• Prison/Correctional Facilities Options
• Remote Applications (see spec sheet 12-2 for more details)
• Two Year Service/Labor Warranty Available
Listed by Underwriters Laboratories Inc., to
U.S. and Canadian safety standards and
Listed by NSF International.
TRAULSEN
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com
Approval: __________________________________
SECTION
7-4

RFF132WUT-FHS - Front View RFF132WUT - Side View
SECTION
7-4
RFF232WUT-HHS - Front View RFF232WUT - Side View
TRAULSEN
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com

RFF132WUT - Top View
RFF332WUT-HHS - Front View
RFF332WUT-HHS - Side View
RLT232WUTFF Top View
RFF332WUT - Top View
TRAULSEN
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com
SECTION
7-4

Project Quantity Item #
Model Specified: CSI Section 11400
Specifications
Construction, Hardware and Insulation
Cabinet exterior front, one piece sides, louver assembly and doors are constructed
of 20 gauge stainless steel with #4 finish. Cabinet interior and door liners are
constructed of stainless steel. The exterior cabinet top, back and bottom are
constructed of heavy gauge aluminized steel. A set of four (4) adjustable 6" high
stainless steel legs are included.
Doors are equipped with a gasket protecting metal door pan, removable plug
cylinder locks and guaranteed for life cam-lift, gravity action, self-closing metal, glide
hinges with stay open feature at 120 degrees. Hinges include a concealed switch to
automatically activate the interior incandescent lighting. Guaranteed for life, work
flow door handles are mounted horizontally over recess in door which limits
protrusion from door face into aisleways. Doors have seamless, polished metal
corners.
Easily removable for cleaning, vinyl magnetic door gasket assures tight door seal.
Anti condensate heaters are located behind each door opening.
Both the cabinet and door(s) are insulated with an average of 2" thick high density,
non-CFC, foamed in place polyurethane.
DIMENSIONAL DATA RFF132WUT RFF232WUT RFF332NUT
Net capacity cu. ft. 24.2 (686 cu l) 51.6 (1462 cu l) 69.5 (1969 cu l)
Length - overall in. 297⁄8 (75.9 cm) 58 (147.3 cm) 765⁄
Depth - overall in. 35 (88.8 cm) 35 (88.8 cm) 35 (88.8 cm)
Depth - over body in. 32 (81.3 cm) 32 (81.3 cm) 32 (81.3 cm)
Depth - with door open 57
90 degrees in.
Clear door width in. 211⁄8 (53.6 cm) 211⁄8 (53.6 cm) 211⁄8 (53.6 cm)
Clear half-door height in. 271⁄2 (69.9 cm) 271⁄2 (69.9 cm) 271⁄2 (69.9 cm)
Clear full-door height in. 575⁄8 (146.3 cm) 575⁄8 (146.3 cm) 575⁄8 (146.3 cm)
Height - overall on 6" legs 831⁄4 (211.5 cm) 831⁄4 (211.5 cm) 831⁄4 (211.5 cm)
Shelf area sq. ft. 18.8 (1.75 sq m) 37.6 (3.49 sq m) 51.9 (4.82 sq m)
Net Wt. lbs. 415 (188 kg) 705 (320 kg) 870 (395 kg)
ELECTRICAL DATA
Voltage 208/115/60/1 208/115/60/1 208/115/60/1
Feed wires with Ground 4 4 4
Full load amperes 8.8 22.0 22.0
1
Wattage
REFRIGERATION DATA
Refrigerant R-404A R-404A R-404A
BTU/HR H.P.
NOTE: Figures in parentheses reflect metric equivalents.
1=Wattage is determined by listed amps X listed volts X an average run time of 70%
for refrigerators and 80% for freezers.
2=Based on a 90 degree F ambient and -20 degree F evaporator.
3=For approximate remote weights deduct 40 lbs. from respective net or gross weight.
For other information on remote models, please refer to spec sheet 12-2.
2
11
⁄16 (146.5 cm) 5711⁄16 (146.5 cm) 553⁄4 (141.6 cm)
1830 2928 2928
4130 (1 HP) 2 x 8260 (1 HP) 2 x 8260 (1 HP)
NOTES
16
(193.8 cm)
Refrigeration System
A top mounted, self-contained, balanced refrigeration system using R-404A refrigerant is conveniently located behind the one-piece louver assembly. It features large,
high humidity, interior mounted evaporator coils, coated with a plastic to retard corrosion, bottom mounted electric condensate evaporator, and an automatic preset time
activated electric defrost. A cord and plug is supplied standard on one section models only. Standard operating temperature is -20°F.
Controller
The easy to use water resistant INTELA-TRAUL
supplied standard. Unit is NAFEM Data Protocol communication (NDP) ready.
Optional hardware required to be NDP compliant. Third party software required for
network connection. It includes a 3-Digit LED Display, Fahrenheit or Celsius
Temperature Scale Display Capability, Defrost Lockout Feature and an RS485 data
port. In addition it includes audio/visual alarms for: Hi/Lo Cabinet Temperature, Door
Open, Clean Condenser, Evaporator Coil and Discharge Line Sensor Failures, and
Power Supply Interruption.
Interior
Standard interior arrangements include three (3) chrome plated wire shelves per
section, mounted on shelf pins. Shelves are full-width, and do not have any large
gaps between them requiring the use of "bridge" or "junior shelves." Recommended
load limit per shelf should not exceed 225 lbs. Optional tray slides may be
purchased in combination with, or in lieu of these. Both standard and optional
interior arrangements are completely installed at the factory.
Warranties
Both a one year parts and labor warranty and a five year compressor warranty (selfcontained models only) are provided standard. An optional 2
and labor warranty is also available. In addition the INTELA-TRAUL® control is
warranted by a two year parts and labor warranty.
FAST FREEZING NOTES:
For best results, it is recommended that loading be held to a minimum with more
frequent use of the freezing process made. Depending on the product variables of
type, size and placement, together with the desired quantity, the time necessary for
freezing will be determined.
Three factors: air temperature, air movement and refrigeration capacity, all
combine to provide fast freezing. A fourth factor is also important. This is the
combined effects of product type, size, quantity and placement. The smaller
the product size and quantity, the faster will its freezing be accomplished. The
placement of product with adequate spacing also assures faster freezing by allowing
freer movement of air around it.
®
microprocessor control system is
nd
year extended parts
Equipped With One NEMA L14-20P Plug
(one section model only)
Full load amps and plug style may vary depending on electrical options
chosen and condensing unit employed.
NOTE: When ordering please specify: Voltage, Hinging, Door Size, Options and
any additional warranties. For fast order entry: Fax 1 (800) 765-8728.
Continued product development may necessitate specification changes without notice.
Part No. TR35806 (revised 1/07)
TRAULSEN
SECTION
7-4
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com
In order to assure optimum performance, the condensing unit MUST have an adequate supply of
air for cooling purposes. Therefore, the operating location must either have a minimum of 12”
clearance overhead of the condensing unit or allow for unrestricted air flow at the back of the unit.
Clearance of at least 12” above is required in order to perform certain maintenance tasks.
REQUIRED CLEARANCES