Quality Refrigeration
OWNER’S MANUAL
Instructions for the installation, operation
and maintenance of all Traulsen:
G-Series Reach-In & Pass-Thru Refrigerators*
G-Series Reach-In & Pass-Thru Hot Food Holding Cabinets
G-Series Reach-In Freezers*
G-Series Hinged Glass Door Refrigerators*
*For equipment produced after 10/1/08 only.
This Traulsen unit is built to our highest quality standards. We build our refrigerators, freezers and heated
cabinets this way as a matter of pride. This philosophy has made Traulsen the leader in commercial refrig-
eration since 1938. We thank you for your choice and condence in Traulsen equipment and we know you
will receive many years of utility from this equipment.
All Traulsen units are placed on a permanent record le with the service department. In the event of any future
questions you may have, please refer to the model and serial number found on the name tag afxed to the
unit. Should you need service, however, call us on our toll free number, 800-825-8220 between 7:30 a.m.
and 4:30 p.m. CST, Monday thru Friday. It is our pleasure to help and assist you in every possible way.
INSTALLER
COMPLETE THE FOLLOWING INFORMATION PRIOR TO UNIT INSTALLATION
INITIAL START DATE: SERIAL NO.
MODEL TYPE:
COMPANY/INDIVIDUAL NAME:
INSTALLER:
FORM NUMBER TR35748 REV. 3/09 P/N 375-60184-00
TABLE OF CONTENTS
I. THE SERIAL TAG Page 1
II. RECEIPT INSPECTION Page 2
III. INSTALLATION
a-Location Page 2
b-Packaging Page 2
c-Installing Legs or Casters Page 2
d-Shelf Pins Page 3
e-Removing The Doors & Hardware Page 3
f-Cord & Plug Page 3
g-Power Supply Page 3
h-Wiring Diagram Page 3
i-Clearance Page 4
j-Installing Optional Interior Kits Page 4
k-ON/OFF Switch Page 4
IV. OPERATION
a-Refrigerators Page 4
b-Freezers Page 4
c-Light Switch Page 4
d-Special Display Mode Page 4
V. CARE & MAINTENANCE
a-Cleaning The Condenser Page 5
b-Hinge Replacement Page 5
c-Replacing The Gaskets Page 5
d-Cleaning The Exterior Page 6
e-Cleaning The Interior Page 6
f-Adjusting The Shelves Page 6
VI. OTHER
a-Service Information Page 6
b-Spare Parts Page 6
c-Warranty Registration Page 6
VII. MICROPROCESSOR CONTROL
a-Control Features Page 6-7
b-Control Panel Page 7
c-Parts Assembly Page 7
d-Notes To The User Page 8
e-Enter The Customer Access Code Page 8
f-Customer Service Parameters Page 9
g-Adjusting Thermostat Set Point High Page 9
h-Adjusting Thermostat Set Point Low Page 10
i-Changing The Temperature Scale Page 10
j-Setting The 24-Hour Clock Page 11
k-Setting The Date Page 12
l-Setting Daylight Savings Time Page 12
m-Starting A Manual Defrost Page 13
n-Setting Defrost Lockouts Page 14
o-Adjusting The Room Temperature Offset Page 15
p-Viewing Coil Sensor Temperature Page 15
q-Hot Food Units - Adjusting The Thermostat Page 16
r-Hot Food Units - Turning The Unit OFF & ON Page 16
s-Hot Food Units - Temperature Adjustment Page 16
VIII. SPARE & REPLACEMENT PARTS LISTING Page 17-18
IX. TROUBLESHOOTING GUIDE Page 19
X. WARRANTY INFORMATION Page 20
XI. NOTES Page 21
XII. INDEX Page 22
FORT WORTH, TX.
SERIAL MODEL
VOLTS Hz PH
TOTAL CURRENT AMPS
MINIMUM CIRCUIT AMPS
MAXIMUM OVERCURRENT PROTECTION AMPS
LIGHTS WATTS
HEATERS AMPS
REFRIGERANT TYPE OZ
DESIGN PRESSURE HIGH LOW
REFRIGERANT TYPE OZ
DESIGN PRESSURE HIGH LOW
370-60294-00 REV (A)
I. THE SERIAL TAG
The serial tag is a permanently afxed label upon
which is recorded vital electrical and refrigeration
data about your Traulsen product, as well as the model and serial number. This tag is located in the upper
right interior compartment on all Traulsen G-Series
refrigerator and freezer models.
READING THE SERIAL TAG
• Serial = The permanent ID# of your Traulsen
• Model = The model # of your Traulsen
• Volts = Voltage
• Hz = Cycle
• PH = Phase
• Total Current = Maximum amp draw
• Minimum Circuit = Minimum circuit ampacity
• Lights = Light wattage
• Heaters = Heater amperage (Hot Food units only)
• Refrigerant = Refrigerant type used
• Design Pressure = High & low side operating
pressures and refrigerant charge
• Agency Labels = Designates agency listings
-1-
II. RECEIPT INSPECTION
III. INSTALLATION (continued)
All Traulsen products are factory tested for performance and are free from defects when shipped. The
utmost care has been taken in crating this product to
protect against damage in transit. All interior ttings
have been carefully secured and the legs are boxed and
strapped inside to prevent damage. Door keys will be
attached to the handle with a nylon strip. The handle
is protected by an easily removable nylon netting.
You should carefully inspect your Traulsen unit for
damage during delivery. If damage is detected, you
should save all the crating materials and make note on
the carrier’s Bill Of Lading describing this. A freight
claim should be led immediately. If damage is subsequently noted during or immediately after installation,
contact the respective carrier and le a freight claim.
Under no condition may a damaged unit be returned to
Traulsen & Co. without rst obtaining written permission (return authorization).
III. INSTALLATION
III. a - LOCATION:
Select a proper location for your Traulsen unit, away
from extreme heat or cold. Allow enough clearance
between the unit and the side wall in order to make
use of the door stay open feature at 120° (self-closing
feature operates up to 90°). The door(s) must be able
to open a minimum of 90° in order to make use of the
maximum clear door width available.
III. c - INSTALLING CASTERS OR LEGS:
A set of four (4) 6” high casters are supplied standard
for all Traulsen G-Series units. These are shipped
from the factory packed inside a cardboard box which
is strapped inside the cabinet to the lower shelf.
Inside it should contain four (4) casters and sixteen
(16) bolts.
Legs in lieu of casters are available as an optional
accessory kit for the same models. These are shipped
inside a separate cardboard box. Inside it should
contain four (4) legs.
WARNING: THE CABINET MUST BE BLOCKED AND
STABLE BEFORE INSTALLING LEGS OR CASTERS.
To install the legs or casters, rst raise and block the
reach-in a minimum of 7” from the oor. For installing legs, thread the legs into the threaded holes on the
bottom of the cabinet (see gure 1). Be certain that
all legs are tightly secured. When the unit is set in
its nal position, it is important for proper operation
that the unit be level. The legs are adjustable for this
purpose, turn the bottom of the leg counterclockwise to
raise it, clockwise to lower it. Level the unit from front
to back as well as side to side in this manner, using a
level placed in the bottom of the cabinet.
III. b - PACKAGING:
All Traulsen units are shipped from the factory bolted
to a sturdy wooden pallet and packaged in a durable
cardboard container. The carton is attached to the
wooden skid with the use of large staples. These
should rst be removed to avoid scratching the unit
when lifting off the crate.
Most exterior stainless steel surfaces have a protective
vinyl covering to prevent scratching during manufacturing, shipping and installation. After the unit is
installed in place of service, remove and discard the
covering from all surfaces.
To remove the wooden pallet, rst if at all possible, we
suggest that the cabinet remain bolted to the pallet
during all transportation to the point of nal installation. The bolts can then be removed with a 3/4” socket
wrench. Avoid laying the unit on its front, side or back
for removal of the pallet.
NOTE: Traulsen does not recommend laying the unit
down on its front, side or back. However, if you must
please be certain to allow the unit to remain in an
upright position afterwards for 24 hours before plugging it in so that the compressor oils and refrigerant
may settle.
Fig. 1
Please note that Traulsen units are not designed to be
moved while on legs. If the unit requires moving, a pallet jack or forklift should be used to prevent damage.
For installing casters, the casters are “plate” type,
and require the use of four (4) bolts each to secure
them rmly to the cabinet bottom at each corner (see
gure 2). The caster bolts are tightened using a 1/2”
socket wrench.
Fig. 2
-2-
III. INSTALLATION (continued)
III. d - SHELF PINS:
The unit is supplied with shelves and shelf pins installed. Check all shelf pins to assure they are tightened down as they may have come loose during shipping. Rotate the pins clockwise until they are secured
against the side of the cabinet.
III. e - REMOVING THE DOORS & HARDWARE:
In order to t through narrow (less than 35”) doorways, it may be sometimes be necessary to remove
the door(s), and/or hinges. To remove any solid door,
begin by removing the plug at the bottom of the top
hinge. Inside the hinge there is a small screw which
secures the door in place. Remove this with a at
head screwdriver and the door can then be lifted off
the hinge (see gure 3).
III. e - REMOV I N G THE DOORS & HARDWARE
(cont’d)
If it is also necessary to remove the hinge hardware
from the cabinet as well, begin by removing the three
Phillips head screws which hold it in place. Set these
components aside for later reassembly (see gure
4).
NOTE: All solid door units include a microswitch for
controlling the interior lighting in the top hinge(s).
Special care should be taken to not damage the wiring
for this during the hinge removal process.
The lock keeper will also need to be removed in order
to reduce theroverall cabinet depth to 32”.
Begin by removing the two (2) Phillips head screws
which secure the lock keeper actuator to the lock
keeper bracket.
Next remove the lock keeper bracket by removing the
two (2) at head screws which secure it in place. Set
these components aside for later reassembly.
To re-install the door and/or hinges, please reverse the
appropriate sections of the preceding procedure.
:
Fig. 3
After removing the door, it is now necessary to remove the hinge assembly and hardware from the door
itself.
To remove the door portion of the hinge from the door,
lift off the hinge cover and then remove the three Phillips head screws which secure the hinge in place on
the door (see gure 4).
III. f - CORD & PLUG:
All G-Series models are supplied with a cord & plug
attached. It is shipped coiled at the top of the cabinet,
secured by a nylon strip. For your safety and protection, all units supplied with a cord and plug include
a special three-prong grounding plug on the service
cord. Select only a dedicated electrical outlet with
grounding plug for power source. NOTE: Do not under
any circumstances, cut or remove the round grounding
prong from the plug, or use an extension cord.
III. g - POWER SUPPLY:
The supply voltage should be checked prior to connection to be certain that proper voltage for the
cabinet wiring is available (refer to the serial tag to
determine correct unit voltage). Make connections in
accordance with local electrical codes. Use qualied
electricians.
Use of a separate, dedicated circuit is required. Size
wiring to handle indicated load and provide necessary
overcurrent protector in circuit (see amperage requirements on the unit’s serial tag).
III. h - WIRING DIAGRAM:
Refer to the wiring diagram for any service work performed on the unit. Should you require one, please
contact Traulsen Service at (800) 825-8220, and provide
the model and serial number of the unit involved.
Fig. 4
-3-
III. INSTALLATION (continued)
IV. OPERATION (continued)
III. i - CLEARANCE:
In order to assure optimum performance, the condensing unit of your Traulsen unit MUST have an adequate
supply of air for cooling purposes. Therefore, the
operating location must either have a minimum of 12”
clearance overhead of the condensing unit or allow for
unrestricted air ow at the back of the unit. Clearance
of at least 12” above is required in order to perform
certain maintenance tasks.
III. j - INSTALLING OPTIONAL INTERIOR KITS:
In addition to their standard interiors, G-Series models also offer the option for additional shelves or tray
slides. If ordered, these are shipped as kits along
with the unit, packaged in a separate cardboard box
which contains all the necessary parts and hardware
for on-site installation.
To install additional shelves, rst remove the white
plastic covers from inside the cabinet. These are located along the same vertical line as the pins already
in place on the interior side walls, back and center
mullion (two and three-section models). This exposes
threaded holes in which you may position the new
shelves. Next insert the gray plastic shelf pins into
these holes and tighten by turning clockwise with your
ngers. After all four pins are in place, the new shelf
should be placed to rest on top of them. The unused
plastic covers may be discarded or saved for future
changes to the cabinet interior.
Installation of optional tray slides varies with each
cabinet, and with each type of tray slide ordered. To
install optional tray slides, follow the directions packaged inside the kit carton.
III. k - ON/OFF SWITCH:
An ON/OFF toggle switch for the power supply is
provided. It is located on top of the unit, mounted to
the side of the evaporator housing. This is shipped
from the factory in the ON position.
IV. OPERATION
IV. a - REFRIGERATORS:
Both refrigerators and freezers do not require manual
defrosting. During normal operation, a refrigerator continuously circulates above freezing cabinet air through
the coil. A compressor “OFF” cycle occurs every hour
to melt any frost which may accumulate on the coil
during the compressor “ON” cycle. The control will
read “dEF” when this occurs. With standard holding
refrigerators, high relative humidity is also maintained
to prevent dehydration of stored product.
IV. b - FREEZERS:
During normal operation, a freezer continuously circulates below freezing cabinet air through the coil.
The coil requires a periodic defrosting for proper
operation. This is accomplished by an automatic,
time activated, temperature/time terminated, defrost
program. The controller is preset at the factory for
six equally spaced defrost cycles within each 24-hour
period.
At the start of a freezer defrost cycle, both the compressor and evaporator fans are off. The microprocessor control will read “dEF” (see gure 5).
°F °C
SET
FREEZER
Fig. 5
The electric heater (attached to the coil) is energized.
When a temperature device afxed to the coil senses
70°F (models with electric defrost), the coil is fully
defrosted and the compressor operation is resumed,
defrost heaters are automatically turned off. The coil
fans are delayed from starting at the termination of
a defrost cycle. Fan operation is automatically resumed, or they can also be started by a time or temp
delay (whichever comes rst). In case of temp delay,
it uses the same coil sensor and starts at 32°F. The
total refrigeration system operation is then resumed.
During freezer defrost operation, heat is conned
to the coil enclosure to prevent any signicant rise
in temperature within the food zone. The fan delay
controls function upon termination of a defrost cycle
is two-fold. First, to prevent blowing warm air into the
food storage area. Second, to prevent any condensation on the defrost coil from being blown into the food
storage area.
The microprocessor control is set from the factory to
terminate defrost at 20 minutes in the event of a sensor
failure. This setting should never be tampered with,
without rst consulting the factory.
-4-
IV. OPERATION (continued)
V. CARE & MAINTENANCE (cont’d)
IV. c - LIGHT SWITCHES:
All G-Series models include a concealed light switch
mounted in the top door hinge(s), which automatically
activates the interior light when the door is opened.
When the door is closed, the lights are not operating.
In addition, on hinged glass door models, an exterior
mounted, illuminated red switch is included for manual
light control. In the ON position, the lights are illuminated whether the doors are open or not. In the OFF
position, the lights are controlled by the hinge switch
as described in the rst paragraph.’
IV. d - SPECIAL DISPLAY OPERATING MODE:
G-Series models built during the summer of 2009 and
beyond will include a special control mode which
disables the external temperature display. Note that
before doing so you must install an interior mounted
thermometer in order to conform with local health
codes.
To initiate this mode press the up and down arrows
simultaneously for 1 second until the temperature
display goes blank. The temperature display will
remain disabled indenately until such time as the
operator wishes to restore normal operation. To do
so simply repeat the process of pressing the up and
down arrows simultaneously for 1 second until the
temperature display illuminates.
Note that in the event power is interrupted for any
reason the display will return to standard operating mode where it displays the correct cabinet air
temperature.
V. CARE & MAINTENANCE
WARNING: DISCONNECT ELECTRICAL POWER SUPPLY BEFORE CLEANING ANY PARTS OF THE UNIT.
V. a - CLEANING THE CONDENSER:
The most important thing you can do to insure a long,
reliable service life for your Traulsen is to regularly
clean the condenser coil.
The condensing unit requires regularly scheduled
cleaning to keep the nned condenser clean of lint and
dust accummulation. Keeping the condenser clean
allows the cabinet to operate more efciently and use
less energy. To clean the condenser, rst disconnect
electrical power to the cabinet and lift up the front
louver assembly. To lift this, remove the two screws
located on both sides at the bottom of the louver as-
sembly (see gure 5). Once the screws are removed,
the panel can be pivoted upwards allowing full access
to the front facing condenser (see gure 6).
Vacuum or brush any dirt, lint or dust from the nned
condenser coil, the compressor and other cooling
V. a - CLEANING THE CONDENSER (cont’d):
Fig. 5
Remove
Screws
Fig. 6
Lift-Up Louver
Assembly
system parts. If signicant dirt is clogging the condenser ns, use compressed air to blow this clear.
Care should be taken not to bend any of the condenser
ns, as this will reduce performance and compressor
life. Lower louver assembly and replace screws to
hold it in place.
V. b - HINGE REPLACEMENT:
To remove the door, remove the plug at the bottom of
the top hinge. Behind this is a screw which secures
the door in place. Remove this with a at head screwdriver and then lift the door off the hinge. To remove
the door portion of the hinge, lift off the hinge cover
and then remove the 3 x Phillips head screws which
secure the hinge in place. To remove the cabinet
portion of the hinge, remove the 3 x Phillips head
screws which hold it in place. On solid door units, the
top hinge(s) contains a switch for controlling the lights.
To reassemble the hinge reverse the procedure.
V. c - REPLACING THE GASKETS:
To remove the gasket to be replaced, grasp it rmly
by one corner and pull it out. Before attempting to
install a new gasket, both the unit and gasket must
be at room temperature. Insert the four corners rst
by using a rubber mallet (or hammer with a block
of wood). After the corners are properly inserted,
work your way towards the center from both ends by
gently h itting with a mallet until the gask et is
completely seated in place (see gure 7 for proper
gasket placement).
Fig. 7
-5-
V. CARE & MAINTENANCE (cont’d)
VI. OTHER (cont’d)
V. d - CLEANING THE EXTERIOR:
Exterior stainless steel should be cleaned with warm
water, mild soap and a soft cloth. Apply with a dampened cloth and wipe in the direction of the metal
grain.
Avoid the use of strong detergents and gritty, abrasive
cleaners as they may tend to mar and scratch the surface. Do NOT use cleansers containing chlorine, this
may promote corrosion of the stainless steel.
Care should also be taken to avoid splashing the unit
with water, containing chlorinated cleansers, when
mopping the oor around the unit.
For stubborn odor spills, use baking soda and water
(mixed to a 1 TBSP baking soda to 1 pint water ratio).
V. e - CLEANING THE INTERIOR:
For cleaning anodized aluminum interiors, the use of
baking soda as described in section “V. d” is recommended. Use on breaker strips as well as door gas-
kets. All interior ttings are removable without tools
to facilitate cleaning.
V. f - ADJUSTING THE SHELVES:
For shelves mounted on pins, rst select the desired
location and remove the white plastic covers in the interior back and sides by rotating them counter-clockwise.
Remove the shelf pins by rotating them counter- clockwise. Install the pins in the desired location by rotating
clockwise. Make sure the pin is securely tightened
down. Do not over tighten. Slide the shelf into its new
position, and replace the white plastic covers into the
holes vacated by the shelf pins.
VI. OTHER
VI. a - SERVICE INFORMATION (cont’d):
Is the electrical cord plugged in?
Is the fuse OK or circuit breaker on?
Is the power switch “ON”?
If after checking the above items and the unit is still
not operating properly, please contact an authorized
Traulsen service agent. A complete list of authorized
service agents was provided along with your Traulsen
unit. If you cannot locate this, you may also obtain the
name of a service agent from the Tech Service page of
our website: www.traulsen.com.
If service is not satisfactory, please contact our inhouse service department at:
Traulsen
4401 Blue Mound Road
Fort Worth, TX 76106
(800) 825-8220
Traulsen reserves the right to change specications
or discontinue models without notice.
VI. b - SPARE PARTS:
Spare or replacement parts may be obtained through a
parts supplier or one of our authorized service agents.
A complete list of authorized service agents accompanies this manual and is also posted on our company’s
ofcial website @ www.traulsen.com.
VI. c - WARRANTY REGISTRATION:
The warranties for your new Traulsen unit may
be registered with us by completing the enclosed
warranty card (shipped with the unit).
VI. a - SERVICE INFORMATION:
°F °C
SET
REFRIGERATOR
FREEZER
VII. MICROPROCESSOR CONTROL
Your new Traulsen G-Series Refrigerator or Freezer is equipped with an electronic microprocessor control, which precisely regulates operation. It is sup-
plied from the factory completely ready for use. See pages 6 thru 15 for more
information.
VIII. a - MICROPROCESSOR CONTROL FEATURES:
Internal Time Clock
• Eliminates defrost time clock (refrigerator and freezer models only).
• Will display only at “Start Up”.
• Battery Back-up (eliminates the need to reset the control after a power failure).
• See “Setting The 24-Hour Clock” on Page 11. (Also required at “Start Up”)
• Will automatically update for Daylight Savings Time. See “Setting Daylight Savings
Time” on page 12.
-6-
VII. MICROPROCESSOR CONTROL (continued)
VII. a - MICROPROCESSOR CONTROL FEATURES (cont’d):
Water Resistant Housing
The digital controller is water resistant not only from the face of the control, but also from the rear of the housing.
Parameter/Service Levels
• See “Customer/Service Parameters” on Page 8 - 9.
Defrost Lockouts - See “Setting Defrost Lockouts” on page 14
• Customers can set up to 4 different defrost lockout periods. The lockout prevents the unit from going into a defrost cycle
during peak kitchen use. Note: The 24-hour clock must be set for this feature to operate correctly.
VII. b - CONTROL PANEL:
LED For ° F
LED For °C
3-Digit (red)
LED Display
Defrost Icon
With LED
VII. c - PARTS ASSEMBLY:
°F °C
SET
FREEZER
REFRIGERATOR
*= Can be ordered separately
**=Requires unit Model No. & S/N to place order.
COIL SENSOR*
337-60071-02
(freezer models only)
CABINET SENSOR*
337-60069-02
-7-
VII. MICROPROCESSOR CONTROL (continued)
VII. d - NOTES TO THE USER:
You only have 20-30 seconds between button pushes. If you take longer than 30 seconds, the controller will revert back
to displaying the cabinet temperature.If you enter the wrong security code, the controller will revert back to displaying the
cabinet temperature. You can exit the parameters at any time by waiting 20-30 seconds for the control to return to normal
operation.
VII. e - ENTER THE CUSTOMER ACCESS:
This is required to set any of the control parameters.
Use the security code “0, A, 1” and the following instructions:
Press the set button . The display will read Customer/Service Access.
Press the set button .
SET
SET
The display will show three zeros with the left zero ashing .
Press the set button .
SET
The display will show three zeros with the center zero ashing .
Press the down arrow key to sequence through F, E, d, C, b, A, 9, 8, 7,…etc.
When you reach “A” press set .
SET
The display will show “zero, A, zero” with the right zero ashing .
Press the up arrow key to sequence through 1, 2, 3, 4, 5, 6, 7, 8, 9, A, b,…etc.
When you reach “1” press set .
SET
The display will read Thermostat Set Point High.
You are now in the CUSTOMER / SERVICE PARAMETERS.
-8-
VII. MICROPROCESSOR CONTROL (continued)
VII. f - CUSTOMER SERVICE PARAMETERS:
Listed below are the available parameters in the order they appear, using the down arrow key on the
controller. You can use either the up or down arrow keys to scroll through the options.
Thermostat Set Point High* Defrost Lockout 2
Thermostat Set Point Low Defrost Lockout 3
Temperature Scale Defrost Lockout 4
Time (24-hour clock) Room Temperature Offset
Date (month - day - year) Evaporator Coil Sensor Temperature
Daylight Savings Dewpoint Compensation Factor
(n/a on G-Series models)
Start Manual Defrost Cabinet Air Temperature
Defrost Lockout 1
VII. g - ADJUSTING THE THERMOSTAT SET POINT HIGH:
This parameter sets the high point of the desired cabinet temperature range. Typically, freezers will
range from -3° F to 0° F (-19° C to -18° C) and refrigerators will range from 36° F to 40° F (2° C to 4°
C) for this parameter setting. This parameter is preset at the factory and does not have to be adjusted
unless the customer chooses to do so. Note: Set Point Low and Set Point High cannot be set to the
same temperature. There will be at least 1-2 degree difference between the two settings.
Follow the instructions to enter the customer access code on page 8. When the control
display reads Thermostat Set Point High. Press the set button .
SET
Use the arrow keys to adjust the temperature to your desired setting.
When the display shows the temperature you want press the set button .
SET
The display will then read Thermostat Set Point High.
You can use the up or down arrow keys to scroll to the next parameter
or wait 30 seconds for the control to return to normal operation.
-9-
VII. MICROPROCESSOR CONTROL (continued)
VII. h - ADJUSTING THE THERMOSTAT SET POINT LOW:
This parameter sets the low point of the desired cabinet temperature range. Typically, freezers will range
from -6° F to -4° F (-21° C to -20° C) and refrigerators will range from 32° F to 34° F ( 0° C to 1° C) for
this parameter setting. This parameter is preset at the factory and does not have to be adjusted unless
the customer chooses to do so. Note: Set Point Low and Set Point High cannot be set to the same
temperature. There will be at least 1-2 degree difference between the two settings.
Follow the instructions to enter the customer access code on page 8. When the control
displays Thermostat Set High, press the down arrow key until the control
display reads Thermostat Set Point Low. Press the set button .
SET
Use the arrow keys to adjust the temperature to your desired setting.
When the display shows the temperature you want press the set button .
SET
The display will then read Thermostat Set Point Low.
You can use the up or down arrow keys to scroll to the next parameter
or wait 30 seconds for the control to return to normal operation.
VII. i - Changing The Temperature Scale:
The temperature scale determines if the temperature displayed will be in degrees
Fahrenheit or degrees Celsius.
Follow the instructions to enter the customer access code on page 8. When the control
displays Thermostat Set High, press the down arrow key until the control
display reads Temperature Scale. Press the set button .
SET
The display will start with the current setting either for degrees Fahrenheit
or for degrees Celsius. Use the arrow keys to toggle between the options.
When the display shows the scale you want press the set button .
SET
The display will then read Temperature Scale.
You can use the up or down arrow keys to scroll to the next parameter
or wait 30 seconds for the control to return to normal operation.
-10-
VII. MICROPROCESSOR CONTROL (continued)
VII. j - SETTING THE 24-HOUR CLOCK:
The internal timeclock must be set in order for the data storage memory to correctly log events and to
allow any defrost lock out to occur at the correct time of day. If the clock is not set, the control assumes
the time is 12 a.m. at the time power is supplied to the unit. The hours on a 24-hour timeclock read the
following way:
H01 = 1:00 a.m. H07 = 7:00 a.m. H13 = 1:00 p.m. H19 = 7:00 p.m.
H02 = 2:00 a.m. H08 = 8:00 a.m. H14 = 2:00 p.m. H20 = 8:00 p.m.
H03 = 3:00 a.m. H09 = 9:00 a.m. H15 = 3:00 p.m. H21 = 9:00 p.m.
H04 = 4:00 a.m. H10 = 10:00 a.m. H16 = 4:00 p.m. H22 = 10:00 p.m.
H05 = 5:00 a.m. H11 = 11:00 a.m. H17 = 5:00 p.m. H23 = 11:00 p.m.
H06 = 6:00 a.m. H12 = 12:00 p.m. H18 = 6:00 p.m. H24 = 12:00 a.m.
Follow the instructions to enter the customer access code on page 8. When the control
displays Thermostat Set High, press the down arrow key until the control
display reads Clock. Press the set button .
SET
The display will show Hours. The right two numbers will be ashing.
Use the arrow keys to set the hour.
When the correct hour is displayed, press the set button .
SET
The display will show Minutes. The right two numbers will be ashing.
Use the arrow keys to set the minutes .
When the correct minutes are displayed, press the set button .
SET
The display will then read Clock.
You can use the up or down arrow keys to scroll to the next parameter
or wait 30 seconds for the control to return to normal operation.
-11-
VII. MICROPROCESSOR CONTROL (continued)
VII. k - SETTING THE DATE:
The date must be set in order for the data storage memory to correctly log events. Follow the instruc-
tions to enter the customer access code on page 8. When the control displays Thermostat
Set Point High, press the down arrow key until the control display reads Date. Press
the set button . The display will show (year). The right two numbers will be ashing.
SET
Press the arrow keys to set the year. When the correct year is displayed, press the set
button . The display will show (month). The right two numbers will be ashing. Use
SET
the arrow keys to set the month. When the correct month is displayed, press the set but-
ton . The display will show (day). The right two numbers will be ashing. Press the
SET
arrow keys to set the day. When the correct day is displayed, press the set button
SET
. The display will then read Date. You can use the up or down arrow keys
to scroll to the next parameter, or wait 30 seconds for the control to return to normal operation.
VIII. l - SETTING DAYLIGHT SAVINGS TIME:
This parameter is preset at the factory to automatically adjust the 24-hour clock for Daylight Savings
Time. Follow the instructions to enter the customer access code on page 8. When the control dis-
plays Thermostat Set Point High, press the down arrow key until the display reads
Daylight Savings Time. Press the set button . The display will show Day-
SET
light Savings Time (Yes, automatically adjust for Daylight Savings Time). For “YES,” press
the set button , for “NO” press the up or down arrow key . The display will read
Daylight Savings Time (no). Press the set button . The display will read Daylight
SET
SET
Savings Time. You can press the the up or down arrow keys to scroll to the next para-
meter or wait 30 seconds for the control to return to normal operation.
-12-
VII. MICROPROCESSOR CONTROL (continued)
VII. m - STARTING A MANUAL DEFROST CYCLE:
This parameter allows a service technician to start a defrost cycle at any time. This parameter
will override any lockout settings.
Follow the instructions to enter the customer access code on page 8. When the control
displays Thermostat Set High, press the down arrow key until the control
display reads Start Manual Defrost.
Press the set button .
SET
The display will show (OFF).
Press either arrow key (ON).
The display will show .
Press the set button .
SET
The display will then read Start Manual Defrost.
You can use the up or down arrow keys to scroll to the next parameter
or wait 30 seconds for the control to return to normal operation.
°F °C
The defrost icon will be lit, and the display will read
SET
DEFROST ICON
FREEZER
NOTE: Traulsen refrigerator units also have an off-cycle defrost once an hour, at which time the
control will read . This defrost cycle is time or temperature terminated and generally
lasts from 3 - 10 minutes in duration (time terminated only on refrigerator models).
-13-
VII. MICROPROCESSOR CONTROL (continued)
VII. n - SETTING THE DEFROST LOCKOUTS:
The defrost lockout parameters allow the customer to prevent the unit from going into a defrost cycle for
two hours during a set timeframe. Customers can set up to four defrost lockout parameters. They are all
programmed the same way. The parameters will be set for the time the lockout is to start. The controller
automatically calculates 2 hours from that setting. The options are similar to the 24-hour clock settings
and are in 30-minute increments. Each of the lockout parameters covers 6 hours of the 24-hour clock.
Note: The 24-hour clock must be set for this feature to operate at the correct time of day. See “Setting
the 24-Hour Clock” on page 11.
OFF OFF OFF OFF
020 = 2:00 a.m. 080 = 8:00 a.m. 140 = 2:00 p.m. 200 = 8:00 p.m.
023 = 2:30 a.m. 083 = 8:30 a.m. 143 = 2:30 p.m. 203 = 8:30 p.m.
030 = 3:00 a.m. 090 = 9:00 a.m. 150 = 3:00 p.m. 210 = 9:00 p.m.
033 = 3:30 a.m. 093 = 9:30 a.m. 153 = 3:30 p.m. 213 = 9:30 p.m.
040 = 4:00 a.m. 100 = 10:00 a.m. 160 = 4:00 p.m. 220 = 10:00 p.m.
043 = 4:30 a.m. 103 = 10:30 a.m. 163 = 4:30 p.m. 223 = 10:30 p.m.
050 = 5:00 a.m. 110 = 11:00 a.m. 170 = 5:00 p.m. 230 = 11:00 p.m.
053 = 5:30 a.m. 113 = 11:30 a.m. 173 = 5:30 p.m. 233 = 11:30 p.m.
060 = 6:00 a.m. 120 = 12:00 p.m. 180 = 6:00 p.m. 240* = 12:00 a.m.
063 = 6:30 a.m. 123 = 12:30 p.m. 183 = 6:30 p.m. 243* = 12:30 a.m.
070 = 7:00 a.m. 130 = 1:00 p.m. 190 = 7:00 p.m. 010 = 1:00 a.m.
073 = 7:30 a.m. 133 = 1:30 p.m. 193 = 7:30 p.m. 013 = 1:30 a.m.
080 = 8:00 a.m. 140 = 2:00 p.m. 200 = 8:00 p.m. 020 = 2:00 a.m.
* Denotes not available.
A lockout cannot be programmed to start at 12:00 a.m. or 12:30 a.m. due to conicts with other internal programs. The defrost lockouts cannot be programmed to run back-to-back. For example, if dL1
is set to 080, then a defrost cycle would be locked out from 8:00 a.m. to 10:00 a.m. Because of the
dL1 setting the dL2 parameter would not let the user choose a lockout start time before 10:30 a.m. All
lockouts are preset at the factory to OFF.
Follow the instructions to enter the customer access code on page 8. When the control
displays Thermostat Set High, press the down arrow key until the control the
control display reads or . Press the set button .
SET
The display will show Off. Press the arrow keys to set the start time.
When the correct time is displayed, press the set button .
SET
The display will then read Thermostat Set Point High.
You can press the up or down arrow keys to scroll to the next parameter
or wait 30 seconds for the control to return to normal operation.
-14-
VII. MICROPROCESSOR CONTROL (continued)
VII. o - ADJUSTING THE ROOM TEMPERATURE OFFSET:
The room temperature offset parameter allows a service technician or end user the ability to have the
display show a temperature that is within three degrees of the actual temperature being read by the
cabinet air sensor. This allows for continuity of reading between different temperature reading devices.
(i.e.: thermistor Vs thermocouple Vs handheld thermometer) This parameter is preset at the factory to
“0” or no offset.
Follow the instructions to enter the customer access code on page 8. When the control displays
Thermostat Set High, press the down arrow key until the control display reads
Room Temperature Offset. Press the set button . Use the arrow keys to adjust the
offset to your desired setting. When the display shows the offset you want press the set button .
SET
SET
The display will then read Room Temperature Offset. You can use the up or down arrow
keys to scroll to the next parameter or wait 30 seconds for the control to return to normal
operation.
VII. p - VIEWING SENSOR TEMPERATURES:
These parameters allow a service technician or customer to view the temperature of all sensors within
the unit. The temperatures cannot be adjusted.
Follow the instructions to enter the customer access code on page 8. When the control displays
Thermostat Set Point High , press the DOWN arrow key unit the display reads Evap-
orator Coil Sensor or Cabinet Air or press the SET button . The display will
SET
read Thermostat Set Point High .
Press the UP or DOWN arrow keys to scroll through the parameters or wait 30 seconds
for the control to return to normal operation.
-15-
VII. MICROPROCESSOR CONTROL (continued)
VII. q - HOT FOOD UNITS, ADJUSTING THE THERMOSTAT & TURNING THE UNIT OFF/ON:
This parameter sets the desired cabinet temperature. Please note that hot food units are delivered
from the factory set to the OFF position.
Follow the instructions to enter the customer access code on page 8. When the control reads
Thermostat Set Point High, press the set button .
SET
Use the arrow keys to adjust the temperature to your desired setting. When the display
shows the temperature you want press the set button . The display will then read
SET
Thermostat Set Point High. You can use the up or down arrow keys to scroll to
the next parameter or press the alarm cancel button to exit.
VII. r - HOT FOOD UNITS, TURNING THE UNIT OFF/ON:
After the temperature has been set, the customer can continuously turn the unit OFF and then back
ON to the same temperature. To turn the unit ON /OFF press the alarm cancel button , (please
note that this feature is not available on versions of the control manufactured prior to September
2000), or if an alarm warning condition is present, use the alternative ON/OFF activation method.
To turn the unit ON/OFF using the alternative method, press both arrows at the same time,
the set temperature will remain in memory.
VII. s - HOT FOOD UNITS, TEMPERATURE ADJUSTMENT:
Press the SET button and the UP ARROW button at the same time. The display will
SET
ash the current temperature setting or OFF (if the unit is turned off). Use the UP or DOWN
ARROW buttons to adjust your desired temperature setting (temperature range is 140° thru
180° F, and OFF) then press the SET button . The display will go back to reading cabinet
SET
temperature. If OFF is selected. the display will then read OFF. NOTE: If you wish to change the
set temperature at anytime follow this procedure.
These models also include a “One-Time Temperature Setting Adjustment” feature. Upon start-up,
the unit will warm-up to the last temperature you had set for it, unless changed.
-16-
VIII. SPARE & REPLACEMENT PARTS LISTING
G100/G110 G120XX G200/G210 G220XX G300/G320 G313XX/G310XX
1 SEC REF 1 SEC FRZ 2 SEC REF 2 SEC FRZ 3 SEC REF 3 SEC FRZ
FULL HEIGHT SOLID DOOR 200-60142-00 200-60142-00 200-60142-00 200-60142-00 200-60142-00 200-60142-00
FULL HEIGHT GLASS DOOR 200-42192-00 N/A 200-42192-00 N/A 200-42192-00 N/A
HALF HEIGHT SOLID DOOR1 200-60140-00 200-60140-00 200-60140-00 200-60140-00 200-60140-00 200-60140-00
HALF HEIGHT GLASS DOOR
HALF HEIGHT SOLID DOOR2 200-60140-01 200-60140-01 200-60140-01 200-60140-01 200-60140-01 200-60140-01
HALF HEIGHT GLASS DOOR
FULL HEIGHT SOLID DOOR GASKET 341-60059-00 341-60059-00 341-60059-00 341-60059-00 341-60059-00 341-60059-00
HALF-HEIGHT SOLID DOOR GASKET 341-60060-00 341-60060-00 341-60060-00 341-60060-00 341-60060-00 341-60060-00
FULL HEIGHT GLASS DOOR GASKET 341-42090-02 N/A 341-42090-02 N/A 341-42090-02 N/A
HALF-HEIGHT GLASS DOOR GASKET 341-42090-01 N/A 341-42090-01 N/A 341-42090-01 N/A
HINGE ASSEMBLY FOR ALL DOORS SER-28583-00 SER-28583-00 SER-28583-00 SER-28583-00 SER-28583-00 SER-28583-00
LOCKKEEPER SER-60433-00 SER-60433-00 SER-60433-00 SER-60433-00 SER-60433-00 SER-60433-00
LOCK CYLINDER FOR ALL DOORS 346-13186-42 346-13186-42 346-13186-42 346-13186-42 346-13186-42 346-13186-42
T-42 KEY FOR ABOVE 346-28924-42 346-28924-42 346-28924-42 346-28924-42 346-28924-42 346-28924-42
EPOXY COATED SHELF
SHELF MOUNTING PIN
6” HIGH LEG (4 req’d. per unit) 344-13168-02 344-13168-02 344-13168-02 344-13168-02 344-13168-02 344-13168-02
SET OF FOUR 6” HIGH CASTERS CK1 CK1 CK1 CK1 CK1 CK1
LOUVER ASSEMBLY 500-70002-00 500-70002-00 500-70008-00 500-70008-00 500-70011-00 500-70011-00
CABINET SENSOR 337-60069-02 337-60069-02 337-60069-02 337-60069-02 337-60069-02 337-60069-02
COIL SENSOR 337-60071-02 337-60071-02 337-60071-02 337-60071-02 337-60071-02 337-60071-02
MICROPROCESSOR CONTROLLER CONSULT FACTORY FOR PART NUMBER
LAMPHOLDER 333-60241-00 333-60241-00 333-60241-00 333-60241-00 333-60241-00 333-60241-00
LIGHT COVER 337-30858-00 337-30858-00 337-30858-00 337-30858-00 337-30858-00 337-30858-00
INCANDESCENT LIGHT BULB 378-29776-00 378-29776-00 378-29776-00 378-29776-00 378-29776-00 378-29776-00
HEATER FOR FULL-HEIGHT DOOR 329-60020-13 329-60020-32 329-60020-13 329-60020-32 329-60020-13 329-60020-32
HEATER FOR HALF-HEIGHT DOOR 329-60020-10 329-60020-26 329-60020-10 329-60020-26 329-60020-10 329-60020-26
DEFROST HEATER N/A 329-60022-00 N/A 329-60021-00 N/A 329-60021-00
EVAPORATOR COIL 322-60003-00 322-60003-00 322-60003-00 322-60020-00 322-60020-00 322-60020-00
EXPANSION VALVE 325-60080-00 325-60080-16 325-60080-00 325-60080-15 325-60080-01 325-60080-02
EVAPORATOR BLOWER ASSEMBLY4 325-60072-02 325-60072-02 325-60071-02 325-60071-02 325-60071-02 325-60071-02
EVAPORATOR MOTOR ASSEMBLY5 433670 433670 433670 433670 325-60071-02 325-60071-02
EVAPORATOR MOTOR ONLY5 430061-2 430061-2 430061-2 430061-2 N/A N/A
EVAPORATOR FAN BLADE5 433090 433090 433090 433090 N/A N/A
EVAPORATOR MOTOR BRACKET5 283439 283439 283439 283439 N/A N/A
PLUNGER SWITCH6 337-28235-00 337-28235-00 337-28235-00 337-28235-00 337-28235-00 337-28235-00
ON/OFF SWITCH 337-60346-00 337-60346-00 337-60346-00 337-60346-00 337-60346-00 337-60346-00
EXTERIOR LIGHT SWITCH
4 PAIRS #1 TYPE TRAY SLIDES8 TK1 TK1 TK1 TK1 TK1 TK1
2 PAIRS #4 TYPE TRAY SLIDES8 TK2 TK2 TK2 TK2 TK2 TK2
4 PAIRS UNIVERSAL TRAY SLIDES8 TK4 TK4 TK4 TK4 TK4 TK4
3 EPOXY COATED SHELVES9 SK30 SK30 N/A N/A SK3010 SK30
3 EPOXY COATED SHELVES
3 CHROME PLATED SHELVES9 SK30C SK30C N/A N/A SK30C10 SK30C
3 CHROME PLATED SHELVES9 N/A N/A SK31C SK31C SK31C11 SK31C
HOT GAS LOOP 326-60102-00 326-60102-00 326-60102-00 326-60099-00 326-60102-00 326-60099-00
WIRING DIAGRAM 379-60385-00 379-60385-00 379-60385-00 379-60385-00 379-60319-00 379-60338-00
REFRIGERANT R-134a R-404A R-134a R-404A R-134a R-404A
COMPRESSOR
RELAY 940-0411-82 040-0102-00 940-0411-82 010-0001-80 040-0102-00 040-0001-48
START CAPACITOR 914-0038-00 014-0008-57 914-0038-00 014-0008-74 014-0008-71 014-0008-63
CONDENSOR FAN MOTOR 050-0258-10 050-0258-10 050-0258-10 050-0267-00 050-0276-00 050-0259-11
CONDENSOR FAN BLADE 083-0122-00 083-0130-00 083-0122-00 083-0133-00 083-0143-00 083-0245-08
CONDENSOR 566-1195-00 066-0336-00 566-1195-00 066-0338-00 066-0338-00 066-0226-00
1
2
(pin mounted)
(4 req’d per shelf)
7
9
200-60141-00 N/A 200-60141-00 N/A 200-60141-00 N/A
200-60141-01 N/A 200-60141-01 N/A 200-60141-01 N/A
340-60070-02 340-60070-02 340-60074-02 340-60074-02 See Notes3 See Notes
3
344-24759-02 344-24759-02 344-24759-02 344-24759-02 344-24759-02 344-24759-02
337-20265-00 N/A 337-20265-00 N/A 337-20265-00 N/A
10
N/A N/A SK31 SK31 SK3111 SK3111
10
11
AR37C1E-IAA-908 RS43C1E-IAA AR37C1E-IAA-908 RS54C1E-CAA RS401E-IAA KAJB-010E-CAV
NOTE
All condensing unit parts are available locally from a Copeland distributor
-17-
VIII. SPARE & REPLACEMENT PARTS LISTING - CONTINUED
SPARE & REPLACEMENT PARTS LISTING NOTATIONS
1= This half half height door can be used as hinged right if mounted on top or hinged left on the bottom.
2= This half half height door can be used as hinged left if mounted on top or hinged right on the bottom.
3= Three section models use a combination of p/n 340-60074-02 in the left and right sections, and p/n 340-70-02 in the center section.
4= Part number applied to units built between August 2001 and March 2004 only.
5= Part numbers apply to units built after March 2004 only.
6= Plunger switch is mounted in hinge and used for automatic light operation.
7= Available for use with glass door models only.
8= If mounting hardware is also required, please specify model and mounting location at time of order to insure provision of correct standards.
9= These shelf kits are intended for mounting on pilasters and clips. If mounting hardware is also required, please specify model and mounting
location at time of order to insure provision of correct standards.
10= Mounting of these shelves is possible in the center section only of three section models.
11= Mounting of these shelves is possible in the left and/or right sections only of three section models.
-18-
IX. TROUBLE SHOOTING GUIDE
FIND YOUR PROBLEM HERE REMEDY
1. Condensing unit fails to start. a. Check if cord & plug has been disconnected.
b. Check control temperature setting.
2. Condensing unit operates for a. Are doors closing properly?
prolonged periods or continuously. b. Dirty condenser or lter. Clean properly.
c. Evaporator coil iced. Needs to defrost. See
instructions for setting a manual defrost cycle
on page 13.
d. Shortage of refrigerant, call service.
3. Food compartment is too warm. a. Check door(s) and gasket(s) for proper seal
b. Perhaps a large quantity of warm food has
recently been added or the door was kept
open for a long period of time, in both
cases, allow adequate time for the cabinet
to recover its normal operating temperature.
c. Control setting too high, readjust
per instructions on page 9.
d. Check that condensing coil is clean.
4. Food compartment is too cold. a. Perhaps a large quantity of very cold or frozen
food has recently been added. Allow adequate
time for the cabinet to recover its normal operating
temperature.
b. Adjust the control to a warmer
setting, see page 10.
5. Condensation on the exterior surface. a. Check door alignment and gaskets for proper seal.
b. Condensation on the exterior surface of the
unit is perfectly normal during periods of
high humidity.
6. Compressor hums but does not start. a. Call for service.
7. No Power To Unit a. Check if cord & plug has been disconnected.
b. Check power supply breaker.
c. Check ON/OFF switch.
-19-
X. WARRANTY INFORMATION
STANDARD DOMESTIC WARRANTY
TRAULSEN warrants new equipment to the original purchaser, when installed within the United States against defective material and
workmanship for one (1) year from the date of original installation. Under this warranty, TRAULSEN will repair or replace, at its option, including service and labor, all parts found to be defective and subject to this warranty. The compressor part is warranted for an
additional four (4) years. During this period TRAULSEN will supply replacement compressor(s) if deemed defective; however, all installation,
recharging, and repair costs will remain the responsibility of the owner.
This warranty does not apply to units altered from the original equipment design or to damage resulting from re, water, burglary, accident, abuse,
misuse, transit, acts of God, terrorism, attempted repairs, improper installation by unauthorized persons, and does not apply to food loss
THERE ARE NO ORAL, STATUTORY OR IMPLIED WARRANTIES APPLICABLE TO TRAULSEN, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WHICH EXTEND BEYOND THE DESCRIPTION ON THE
FACE HEREOF. TRAULSEN SHALL HAVE NO OBLIGATION OR LIABILITY FOR CONSEQUENTIAL OR SPECIAL DAMAGES, GROWING OUT OF
OR WITH RESPECT TO THE EQUIPMENT OR ITS SALE, OPERATION OR USE, AND TRAULSEN NEITHER ASSUMES NOR AUTHORIZES ANYONE
ELSE TO ASSUME FOR IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THE EQUIPMENT OR ITS SALE, OPERATION OR USE OTHER
THAN AS STATED HEREIN.
G-SERIES MICROPROCESSOR CONTROL WARRANTY
TRAULSEN warrants to the original purchaser of the G-Series Microprocessor control when installed as part of the Refrigeration Equipment
manufactured and sold by TRAULSEN, to be free of defects in material and workmanship under normal service and use for a period of one (1)
year from the date of installation, not to exceed fteen (15) months from the original date of shipment. Under this warranty statement, TRAULSEN
will repair or exchange at TRAULSEN’S discretion, F.O.B. factory, any part of said control, which proves to be defective. Inspection by the
TRAULSEN Service Department of parts claimed defective shall be nal in determining warranty status. The warranty is to include repair or
exchange of any defective In-Warranty control or part(s) of said control for:
Part(s) - Any TRAULSEN G-Series Microprocessor Control supplied part(s) found to be defective.
Labor - The labor charges from a TRAULSEN Certied Service Agent to effect the repair or exchange of the defective part(s).
“Defective Part Return” - All claimed defective part(s) must be returned to TRAULSEN for defect validation within 30 days from the date of the
repair. Failure to return all claimed defective part(s) to TRAULSEN will invalidate the warranty claim, this warranty statement, and forfeit payment for those repairs effected.
This warranty does not apply to units altered from the original equipment design or to damage resulting from re, water, burglary, accident,
abuse, misuse, transit, acts of God, terrorism, attempted repairs, improper installation by unauthorized persons, and does not apply to food
loss, and will not apply if said equipment is located outside The United States.
INTERNATIONAL COMMERCIAL WARRANTY
(for Canadian warranties see domestic US warranty)
TRAULSEN warrants to the original purchaser the Refrigeration Equipment manufactured and sold by it to be free from defects in material and
workmanship under normal use and service for a period of one (1) year from date of shipment. Under this warranty, TRAULSEN will reimburse
the purchaser for the replacement of any part of said equipment (excluding dryers & refrigerant gas) which then proves to be defective. This
warranty does not apply to units altered from the original equipment design or to damage resulting from re, water, burglary, accident, abuse,
misuse, transit, acts of God, terrorism, attempted repairs, improper installation by unauthorized persons, and does not apply to food loss.
TRAULSEN’S standard warranty does not apply to Export Sales. Rather, for a period of one (1) year from date of original installation not to
exceed Fifteen (15) months from date of shipment from factory, TRAULSEN:
will replace, F.O.B. factory, any defective parts normally subject to warranty.
will not cover the cost of packing, freight or labor such costs being the sole responsibility of the dealer.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EITHER EXPRESSED OR IMPLIED AND CONSTITUTES
TRAULSEN’S FULL OBLIGATION AND LIABILITY.
-20-
X. NOTES
-21-
XI. INDEX
A
Automatic Condensate Evaporator 3
B
Battery Back-Up 6
C
Casters 2
Cleaning, The Condenser 5
Cleaning, The Exterior 6
Cleaning, The Interior 6
Clock, Setting The 24-Hour 11
Condensate Evaporator 3
Control Panel 7
Cord & Plug 3
Compressor Hold Down Provisions 3
Clearance 4
Customer Access Code 8
Customer Service Parameters 9
D
Date, Setting The 12
Daylight Savings Time, Setting 12
Defrost 4
Defrost Icon 13
Defrost Lockouts, Setting 14
E
Evaporator Coil Sensor 9, 15
F
Freight Damage 2
G
Gaskets, Replacing The 5
H
Hinge, Replacement 5
I
Internal Time Clock 6, 11
J
K
M
Manual Defrost Cycle, Starting 13
Microprocessor Control, Features 6-7
N
O
Off-Cycle Defrost 13
ON/OFF Switch 4
P
Packaging 2
Parts Assembly 7
Parts, Spare & Replacement 17-18
Power Supply 4
R
Return Authorization 2
Room Temperature Offset 15
S
Self-Closing Door Feature 2
Sensor Temperatures, Viewing 15
Serial Tag 1
Shelf Pins 3-4, 6
Shelves 3-4, 6
Stay Open Door Feature 2
T
Temperature Scale, Changing The 10
Thermostat Set Point High 9
Thermostat Set Point Low 10
Tray Slides 4
Trouble Shooting 16
U
V
Vinyl, Protective Covering 2
W
Warranty 20
Warranty Regisration 6
Water Resistant Housing 7
Wiring Diagram 3
L
Legs 2
Light Switch 5
Location, Selecting Proper 2
Louver Assembly 5
X
Y
Z
-22-
HOURS OF OPERATION:
Monday thru Friday 7:30 am - 4:30 pm CST
Quality Refrigeration
Traulsen
4401 Blue Mound Road Fort Worth, TX 76106
Phone: (800) 825-8220 Fax-Svce: (817) 740-6757
Website: www.traulsen.com
© 2009 Traulsen - All Rights Reserved
Loading...