iGPS-M Pro USER’S MANUAL
1
iGPS-M Pro USER’S MANUAL
iGPS-M Pro Introduction ....................................................... 3
iGPS-M Pro Key Feature ..................................................... 3
Possible Application ....................................................... 3
Installation Guide ............................................................ 4
Familiarize your iGPS-M Pro ................................................... 6
Specifications ............................................................. 6
Interface .................................................................. 7
Water-proof housing with magnet on the bottom .............................. 8
LED Light .................................................................. 8
Troubleshooting ............................................................... 8
2
iGPS-M Pro USER’S MANUAL
iGPS-M Pro Introduction
The iGPS-M Pro is an outstanding high sensitivity GPS receiver.
Its excellent performance easily conquers the most difficult tasks.
In addition, it provides various functions to meet customers’ demand.
iGPS-M Pro employs powerful GPS solution. It provides marvelous
navigation performance under dynamic conditions in areas with
limited sky view like urban canyons. It also has high sensitivity
for weak signal operation without compromising accuracy.
Undoubtedly, iGPS-M Pro is the best choice for you.
Market Leading System Performance
Ultra-low power consumption makes iGPS-M Pro the best GPS on the market. Nevertheless,
there are no compromises in performance. The iGPS receiver has a navigation sensitivity
making it applicable even for extremely demanding applications and environments.
iGPS-M Pro Key Feature
Thin module form factor – 64mm(L) x 57mm(W) x 16mm(H)
51-CH. GPS Technology
Very Fast TTFF
Sensitivity: -158dBm (Tracking)
NMEA0183 V3.01 protocols
Accurate 1PPS timing output (optional)
Possible Application
Mapping devices for PC & Pocket PC
Personal Navigation or touring devices
AVL and Location-Based service system
Data logging for marine Navigation
Support 1pps output for timer
Tracking devices/system
Mileage Management
Fleet Management
Car Navigation
3
iGPS-M Pro USER’S MANUAL
Installation Guide
Step I：Check your iGPS-M Pro package
Please check the iGPS-M Pro package. If any items are missing or damaging, please
contact our distributor immediately.
The standard package of iGPS-M Pro contains:
z iGPS-M Pro Receiver
z CD ROM (Only USB type is with CD ROM, USB drivers is included)
z Y cable (optional)
With different brand/type of handheld device, the iGPS-M Pro receiver needs to
use different type of car charger.
Step II：Connect iGPS-M Pro receiver to PC/Lap top or handheld device
z For PS2 type: No USB Driver Installation is needed.
z For USB type: please follow the illustration as below. Before the USB
connector plugs in your PC/Lap top, please have your USB Driver Installation
ready.
z For RJ45 type: No USB Driver Installation is needed.
4
iGPS-M Pro USER’S MANUAL
Step III：Check if the LED is on.
Once your PC/Lap top or car charger supplies power, the iGPS-M Pro receiver should
shine on the LED. At meantime, the LED will be flashing and it means iGPS-M Pro
is fixed, enable the positioning function.
5
iGPS-M Pro USER’S MANUAL
Familiarize your iGPS-M Pro
Specifications
GPS Technology MTK 51 channels
Sensitivity -158 dBm (tracking)
Update Rate 1Hz
Accuracy
Acquisition Time (Cold/Warm/Hot Start) 36/33/1 sec
Reacquisition 1 sec
Dynamics Altitude: 18000m max.
DGPS WAAS, EGNOS Enable
Operating Temperature
Storage Temperature
Operating Humidity 5% to 95% non condensing
Primary Power +5V~7.5V DC
Power Consumption 20mW @3.0V
Interface PS2/ USB/ RJ45
Protocol NMEA 0183 v3.01,9600 bps
Antenna Internal passive antenna
NMEA Message GGA, GLL, GSA, GSV, RMC, and VTG
Dimension 64mm(L) x 57mm(W) x 16.54mm(H)
Position: Without aid: 3.0 m 2DRMS , < 3m
CEP(50%) without SA
Velocity: Without aid: 0.1 m/s
Time: 50ns RMS
Velocity: 515m/sec
Vibration: 4G max.
-30℃ to +85℃
-45℃ to +90℃
6
iGPS-M Pro USER’S MANUAL
Interface
1. PS2 interface
As shown in the illustration on the right, the length of the wire on iGPS-M Pro
receiver is 2 meters. There is a PS-2 connector for the connection to PC/Lap top
or handheld device. The pin assignment is shown below.
1.1 PS2 female cable definition
Signal Name
Pin
RS-232
1 RS232 TX
2 +5VDC
3 NC
4 Ground
5 1 PPS (optional)
6 RS232 RX
2. USB interface
7
iGPS-M Pro USER’S MANUAL
3. RJ45 interface
Signal Name
Pin
RS-232
2 Red (+5VDC)
8 White (RS232 RX)
6 Green (RS232 TX)
7 Black (Ground)
Water-proof housing with magnet on the bottom
There are 4 magnets on the bottom side of iGPS-M Pro receiver for attaching on your
car. The housing of iGPS-M Pro receiver has waterproof, it can avoid the water permeates
your iGPS-M Pro receiver while you attach it outside of the car.
LED Light
There is an LED light near the output cable on the back of iGPS-M Pro receiver.
When the iGPS-M Pro supplied 5V DC power, the LED will be on. It means your PC/Lap
top or car charger start to supply power to iGPS-M Pro receiver.
Troubleshooting
When your iGPS-M Pro receiver could not operate, please follow the instruction
to do the troubleshooting as below.
1. iGPS-M Pro receiver does not shine on the LED
z It means iGPS-M Pro does not have power supply. Please check if the
connector plugs in properly as the step II.
2. iGPS-M Pro receiver’s LED is flashing, but the connection between iGPS-M Pro
receiver and the E-map can not be established. Please make sure the settings
of COM Port Number and Baud rate are correct.
z Most of E-map provides scan function to search COM Port. Please scan
it for the correct COM Port number that iGPS-M Pro receiver is utilizing.
z The default Baud rate is 9600. For COM port, please go to the MS Windows’
device manager to check the correct COM port first.
z If a USB cable is used to connect to PC/Lap top, please make sure the
UBS driver is installed successfully.
8
Loading...