Transtek Medical Electronics TMB1872BS User Manual

User Manual
Blood Pressure Monitor
Version:1.0
TMB-1872-B
Arm Type
Guangdong Transtek Medical Electronics Co., Ltd.
Zone B, No.105 ,Dongli Road, Torch Development District, Zhongshan,528437,Guangdong,China
Thank you very much for selecting TRANSTEK Blood Pressure Monitor TMB-1872-B.
Please read the user manual carefully and thoroughtly so as to ensure the safe usage of this product, Keep the manual well for further reference in case you have problems.
CATALOGUE
CATALOGUE
Table of Contents
INTRODUCTION...................................................................................................................2
General Description Indications for Use Contraindications Measurement Principle Safety Information LCD Display Signal Monitor Components List
BEFORE YOU START...........................................................................................................9
The Choice of Power Supply Installing and Replacing the Batteries Setting Date, Time and Measurement Unit Select the User
Pair-up the Blood Pressure Monitor with Your Device
MEASUREMENT..................................................................................................................15
Tie the Cuff Start the Measurement
DATA MANAGEMENT..........................................................................................................18
Recall the Records Delete the Records
INFORMATION FOR USER................................................................................................21
Tips for measurement Maintenances
ABOUT BLOOD PRESSURE..............................................................................................23
What are systolic pressure and diastolic pressure? What is the standard blood pressure classification? Irregular heartbeat detector Why does my blood pressure fluctuate throughout the day? Why do I get a different blood pressure at home compared to the hospital? Is the result the same if measuring on the right arm?
TROUBLESHOOTING........................................................................................................25
SPECIFICATIONS...............................................................................................................26
AUTHORIZED COMPONENTS .........................................................................................27
CONTACT INFORMATION.................................................................................................27
FCC STATEMENT...............................................................................................................28
COMPLIED STANDARDS LIST..........................................................................................29
EMC GUIDANCE................................................................................................................30
1
INTRODUCTION INTRODUCTION
General Description
Thank you for selecting TRANSTEK arm type blood pressure monitor (TMB-1872-B). The monitor features blood pressure measurement, pulse rate measurement and the result storage. The design provides you with two years of reliable service.
Readings taken by the TMB-1872-B are equivalent to those obtained by a trained observer using the cuff and stethoscope auscultation method.
This manual contains important safety and care information, and provides step by step instructions for using the product.
Read the manual thoroughly before using the product.
Features: 60*74mm Digital LCD display Maximum 60 records per each user Measuring during inflation technology
Indications for Use
The Transtek Blood Pressure Monitor is a digital monitor intended for use in measuring blood pressure and heartbeat rate with arm circumference ranging
from 22cm to 32cm(about 8¾˝-12½˝) or 22cm to 42cm(about 8¾˝-16½˝).
It is intended for adult indoor use only.
Contraindications
1.The device should not be used by any person who may be suspected of,or is pregnant .
2.The device is not suitable for use on patients with implanted,electrical devices, such as cardiac pacemakers, defibrillators.
Measurement Principle
This product uses the Oscillometric Measuring method to detect blood pressure. Before every measurement, the unit establishes a “zero pressure” equivalent to the atmopheric pressure. Then it starts inflating the arm cuff, meanwhile, the unit detects pressure oscillations generated by beat-to-beat pulsatile, which is used to determine the systolic and diastolic pressure, and also pulse rate.
Safety Information
The signs below might be in the user manual, labeling or other component.
They are the requirement of standard and using.
Symbol for “THE OPERATION GUIDE MUST BE READ”
Symbol for “MANUFACTURER”
Symbol for “SERIAL NUMBER”
SN
Symbol for “DIRECT CURRENT”
For indoor use only
F1
T1A/250V Φ3.6*10CCC
Caution: These notes must be observed to prevent any damage to the device.
The Green Dot is the license symbol of a European network of industry-funded systems for recycling the packaging materials of consumer goods.
Symbol for “TYPE BF APPLIED PARTS”
Symbol for “ENVIRONMENT PROTECTION - Electrical waste products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice”
Symbol for “Class II Equipment”
Symbol for “MANUFACTURE DATE”
Symbol for “RECYCLE”
2
3
INTRODUCTIONINTRODUCTION
CAUTION
* This device is intended for adult use in homes only. * The device is not suitable for use on neonatal patients, pregnant women,patients with implanted, electronical devices, patients with pre-eclampsia, premature ventricular beats, atrial fibrillation, peripheral, arterial disease and patients undergoing intravascular therapy or arterio-venous shunt or people who received a mastectomy. Please consult your doctor prior to using the unit if you suffer from illnesses. * The device is not suitable for measuring the blood pressure of children. Ask your doctor before using it on older children. * The device is not intended for patient transport outside a healthcare facility. * The device is not intended for public use. * This device is intended for no-invasive measuring and monitoring of arterial blood pressure.It is not intended for use on extremities other than the arm or for functions other than obtaining a blood pressure measurement. * Do not confuse self-monitoring with self-diagnosis. This unit allows you to monitor your blood pressure.Do not begin or end medical treatment without asking a physician for treatment advice. * If you are taking medication,consult your physician to determine the most appropriate time to measure your blood pressure. Never change a prescribed medication without consulting your physician. * Do not take any therapeutic measures on the basis of a self measurement. Never alter the dose of a medicine prescribed by a doctor. Consult your doctor if you have any question about your blood pressure. * When the device is used to measure patients who have common arrhythmias such as atrial or ventricular premature beats or atrial fibrillation, the best result may occur with deviation. Please consult your physician about the result. * Don't kink the connection tube during use, otherwise, the cuff pressure may continuously increase which can prevent blood flow and result in harmful injury to the PATIENT. * When using this device, please pay attention to the following situation which may interrupt blood flow and influence blood circulation of the patient, thus cause harmful injury to the patient: connection tubing kinking too frequent and consecutive multiple measurements; the application of the cuff and its pressurization on any arm where intravascular access or
therapy, or an arterio-venous (A-V) shunt, is present; inflating the cuff on the side of a
mastectomy. * Warning: Do not apply the cuff over a wound;otherwise it can cause further injury. *Do not inflate the cuff on the same limb which other monitoring ME equipment is applied around simultaneously, because this could cause temporary loss of function of those simultaneously-used monitoring ME equipment. *On the rare occasion of a fault causing the cuff to remain fully inflated during measurement, open the cuff immediately. Prolonged high pressure (cuff pressure 300mmHg or constant pressure 15mmHg for more than 3 minutes) applied to the arm may lead to an ecchymosis. *Please check that operation of the device does not result in prolonged impairment of patient blood circulation.
4
CAUTION
* When measurement, please avoid compression or restriction of the connection tubing. * The device cannot be used with HF surgical equipment at the same time. * The ACCOMPANYING DOCUMENT shall disclose that the SPHYGMOMANOMETER was clinically investigated according to the requirements of ISO 81060-2:2013. * To verify the calibration of the AUTOMATED SPHYGMOMANOMETER, please contact the manufacturer. * This device is contraindicated for any female who may be suspected of, or is pregnant. Besides providing inaccurate readings, the effects of this device on the fetus are unknown. * Too frequent and consecutive measurements could cause disturbances in blood circulation and injuries. * This unit is not suitable for continuous monitoring during medical emergencies or operations.Otherwise, the patient’s arm and fingers will become anaesthetic, swollen and even purple due to a lack of blood. * When not in use, store the device with the adapter in a dry room and protect it against extreme moisture, heat, lint, dust and direct sunlight. Never place any heavy objects on the storage case. * This device may be used only for the purpose described in this booklet. The manufacturer cannot be held liable for damage caused by incorrect application. *This device comprises sensitive components and must be treated with caution. Observe the storage and operating conditions described in this booklet. * The equipment is not AP/APG equipment and not suitable for use in the presence of a flammable anesthetic mixture with air of with oxygen or nitrous oxide. * Warning: No servicing/maintenance while the ME equipment is in use. * The patient is an intended operator. * The patient can measure, transmit data and change batteries under normal circumstances and maintain the device and its accessories according to the user manual. * To avoid measurement errors, please avoid the condition of strong electromagnetic field radiated interference signal or electrical fast transient/burst signal. * The blood pressure monitor, its adaptor, and the cuff are suitable for use within the patient environment. If you are allergic to polyester, nylon or plastic, please don't use this device. * During use, the patient will be in contact with the cuff. The materials of the cuff have been tested and found to comply with requirements of ISO 10993-5:2009 and ISO 10993-10:2010. It will not cause any potential sensation or irritation reaction. * Adaptor is specified as a part of ME EQUIPMENT. * If you experience discomfort during a measurement, such as pain in the arm or other complaints, press the START/STOP button to release the air immediately from the cuff. Loosen the cuff and remove it from your arm.
* If the cuff pressure reaches 40 kPa (300 mmHg), the unit will automatically deflate. Should the cuff not deflate when pressure reaches 40 kPa (300 mmHg), detach the cuff
from the arm and press the START/STOP button to stop inflation. * Before use, make sure the device functions safely and is in proper working condition. Check the device, do not use the device if it is damaged in any way. The continuous use of a damaged unit may cause injury, improper results, or serious danger. * Do not wash the cuff in a washing machine or dishwasher!
5
INTRODUCTIONINTRODUCTION
CAUTION
* The service life of the cuff may vary by the frequency of washing, skin condition, and storage state. The typical service life is 10000 times. * It is recommended that the performance should be checked every 2 years and after maintenance and repair, by retesting at least the requirements in limits of the error of the
cuff pressure indication and air leakage (testing at least at 50mmHg and 200mmHg).
* Please dispose of ACCESSORIES, detachable parts, and the ME EQUIPMENT according to the local guidelines. * Manufacturer will make available on request circuit diagrams, component part lists, descriptions, calibration instructions,etc., to assist to service personnel in parts repair. * The plug/adapter plug pins insulate the device from the main supply. Do not position the device in a position where it is difficult to disconnect from the supply mains to safely terminate operation of ME equipment. * The operator shall not touch output of batteries/adapter and the patient simultaneously. * Cleaning :Dust environment may affect the performance of the unit. Please use the soft cloth to clean the whole unit before and after use. Don’t use any abrasive or volatile cleaners. * The device doesn’t need to be calibrated within two years of reliable service. * If you have any problems with this device, such as setting up, maintaining or using, please contact the SERVICE PERSONNEL of Transtek. Don’t open or repair the device by yourself in the event of malfunctions. The device must only be serviced, repaired and opened by individuals at authorized sales/service centers. * Please report to Transtek if any unexpected operation or events occur. * Keep the unit out of reach of infants, young children or pets to avoid inhalation or swallowing of small parts. It is dangerous or even fatal. * Be careful to strangulation due to cables and hoses, particularly due to excessive length. * At least 30 min required for ME equipment to warm from the minimum storage temperature between uses until it is ready for intended use. At least 30 min required for ME equipment to cool from the maximum storage temperature between uses until it is ready for intended use. * This equipment needs to be installed and put into service in accordance with the information provided in the ACCOMPANYING DOCUMENTS; * Wireless communications equipment such as wireless home network devices, mobile phones, cordless telephones and their base stations, walkie-talkies can affect this equipment and should be kept at least a distance d away from the equipment. The distance d is calculated by the MANUFACTURER from the 80MHz to 5.8 GHz column of Table 4 and Table 9 of IEC 60601-1-2:2014, as appropriate. * Please use ACCESSORIES and detachable parts specified/ authorised by MANUFACTURE. Otherwise, it may cause damage to the unit or danger to the user/patients. * There is no luer lock connectors are used in the construction of tubing, there is a possibility that they might be inadvertently connected to intravascular fluid systems, allowing air to be pumped into a blood vessel. * Please use the device under the environment which was provided in the user manual.
6
LCD Display Signal
SYMBOL DESCRIPTION
Systolic blood pressure High blood pressure
Diastolic blood pressure Low blood pressure
Pulse display
Average value
Memory
Motion indicator
mmHg
mmHg
Low battery Batteries are low and need to be replaced
Irregular heartbeat
Blood pressure level indicator
Current Time
Heartbeat
User 1 Start measurement for User 1
User 2 Start measurement for User 2
Bluetooth icon
EXPLANATION
Pulse in beats per minute
The average value of blood pressure
Indicate it is in the memory mode and which group of memory it is.
Motion may result in an inaccurate measurement
Measurement Unit of the blood pressure
(1mmHg=0.133kPa)
Blood pressure monitor is detecting an irregular heartbeat during measurement.
Indicate the blood pressure level
Year/Month/Day, Hour/Minute
Blood pressure monitor is detecting a heartbeat during measurement.
The bluetooth icon blinks when the bluetooth is working
7
INTRODUCTION
BEFORE YOU START
Monitor Components
AIR CONNECTOR PLUG
MEM BUTTON
CUFF
AIR HOSE
SET BUTTON
Component list of pressure measuring system 1 Cuff 2 Air pipe 3 PCBA 4 Pump 5 Valve
List
1.Blood Pressure Monitor
(TMB-1872-B)
3. 4*AAA batteries
8
2.Cuff (Type BF applied part)
4.User manual
LCD DISPLAY
USB INTERFACE
START/STOP BUTTON
BATTERY COMPARTMENT
(22~32cm or 22~42cm)
5.USB Cable and AC Adaptor
(BLJ06L050100U-U)
The Choice of Power Supply
1.Battery powered mode:
6VDC 4*AAA batteries
AC adaptor powered mode:
2.
Please use the AC adaptor and USB cable just like the following picture:
5V 1A
AC adaptor
CAUTION
In order to get the best effect and protect your monitor,please use the right
battery and special power adaptor which complies with local safety standard.
Installing and Replacing the Batteries
Slide off the battery cover.
Install the batteries by matching
the correct polarity, as shown.
Replace the battery cover.
Replace the batteries whenever the below happens
The shows
The display is dim
The display does not light up
CAUTION
Do not use new and used batteries together. Do not use different types of batteries together. Do not dispose the batteries in fire. Batteries may explode or leak. Remove batteries if the device is not likely to be used for some time. Worn batteries are harmful to the environment. Do not dispose with daily garbage. Remove the old batteries from the device following your local recycling guidelines.
9
BEFORE YOU START BEFORE YOU START
Setting Date, Time
It is important to set the clock before using your blood pressure monitor, so that a time stamp can be assigned to each record that is stored in the memory. (The setting range of the year :2018—2058 time:24H/12 H)
1.When the monitor is off, presse “SET” button shortly it will display the time.Then press “SET” button for 3 seconds to enter the mode for year setting.
2.Press “MEM” button to change the [YEAR]. Each press will increase the numeral by one in a cycling manner.
3.When you get the right year, press “SET” button to set down and turn to next step.
4.Repeat steps 2 and 3 to
set the [MONTH] and [DAY].
.Repeat steps 2 and 3 to
5
set the [TIME FORMAT] between 12h and 24h.
.Repeat steps 2 and 3 to
6
set the [HOUR] and [MINUTE].
10
.After the [MINUTE] is set,
7
the LCD will display “donE” first,then display all the settings you have done and then it will turn off.
11
BEFORE YOU START
BEFORE YOU START
Select the User
1.
When the monitor is off, press and hold “MEM ”button to enter user setting mode. The user ID will blink.
Then press “ MEM ” button again, select the user ID between
2.
user 1 and user 2 .
3.
After selecting the suitable user ID, press “SET” button to confirm. It will display “User ID+ donE” and then turn off.
12
Pair-up the Blood Pressure Monitor with Your Device
Download the Transtek Health app from APP Store or Google Play, and turn on the Bluetooth.Install the APP, and register an account. Then set your personal information (Gender, Birthday, Height, Weight, Name and so on).
1.Turn on Bluetooth and the app. Make sure both are ON when pair-up is proceeding.
2
.When the monitor is OFF, press and hold the START/STOP button to start
pair-up. The symbol“ + ” and “ + ” will be shown on the LCD alternatively, indicating pair-up is proceeding.
3.Then please select the user ID you want to connect with your smartphone on the app to continute the pair-up.
If SUCCEED, symbol “ + ” will be shown on the LCD.
4.The monitor will shut off after Pair-up process is
complete.
Bluetooth Module No.: LS8261 RF Frequency Range: 2400 MHz to 2483.5 MHz Output Power Range: ≤8dBm Supply Voltage: 1.9-3.6 V Transmitting Distance: 10 meters
If FAIL, symbol “ + ”
will be shown on the LCD.
13
BEFORE YOU START
MEASUREMENT
List of compatible devices: For iOS devices: The operating system must be iOS 8 or more, such as iPhone 4S, iPhone 5/5C/5S, iPhone 6/6 Plus and so on. For Android devices: The operating system must be 4.3 or more.
CAUTION
Interference may occur in the vicinity of equipment marked with the following symbol . And TMB-1872-B may interfering vicinity electrical equipment. Sensitive people, including pregnant women pre-eclamptic and those who implanted medical electronic instruments, should avoid using the unit whenever possible. Keep the monitor at least 20 centimeters away from the human body
(especially the head) when the data transmission is proceeding after
measurement. To enable the data transmission function, this product should be paired to Bluetooth end at 2.4 GHz.
How to mitigate possible interference?
1.
The range between the device and BT end should be reasonably close, from 1 meter to 10 meters. Please ensure no obstacles between the device and BT end so as to obtain quality connection and to lower the RF output range.
2.
To avoid interference, other electronic devices (particularly those with
wireless transmission / Transmitter) should be kept at least 1 meter away
from the monitor.
Tie the Cuff
1.
Remove all jewelry, such as watches and bracelets from your left arm.Note: If your doctor has diagnosed you with poor circulation in your left arm, use your right arm.
2.
Roll or push up your sleeve to expose the skin. Make sure your sleeve is not too tight.
3.
Hold your arm with your palm facing up and tie the cuff
on your upper arm, then position the tube off-center toward the inner side of arm in line with the little finger. Or position
the artery mark over the main artery (on the inside of your arm).
Note: Locate the main artery by pressing with 2 fingers approximately 2 cm above the bend of your elbow on the inside of your left arm. Identify where the pulse can be felt the strongest. This is your main artery.
The cuff should be snug but not too tight. You should be able to
4.
insert one finger between the cuff and your arm.
Sit comfortably with your tested arm resting on
5.
a flat surface. Place your elbow on a table so that the cuff is at the same level as your heart. Turn your palm upwards. Sit upright in a chair, and take 5-6 deep breaths.
6.
Helpful tips for Patients, especially for Patients with Hypertension:
Rest for 5 minutes before first measurement. Wait at least 3 minutes between measurements. This allows your blood circulation to recover. Take the measurement in a silent room. The patient must relax as much as possible and do not move and talk during the measurement procedure. The cuff should maintain at the same level as the right atrium of the heart. Please sit comfortably. Do not cross your legs and keep your feet flat on the ground. Keep your back against the backrest of the chair.
For a meaningful comparison, try to measure under similar conditions. For example, take daily measurements at approximately the same time, on the same arm, or as directed by a physician.
2~3cm
1514
MEASUREMENT MEASUREMENT
Start the Measurement
1.When the monitor is off, the monitor, and it will finish the whole measurement .
( Take user 1 for example.)
Inflating and measuring.
press “Start/Stop” button to turn on
Adjust the zero. LCD display
Display and save the results.
STAR T
STO P
If the data transmission fails, the Bluetooth symbol blinks all the time , and it will diaplay
If the data transmission succeeds, the Bluetooth symbol will not blink then the device will turn off.
2.Press “Start/Stop” button to power off, otherwise it will turn off within 1 minute.
symbol “ + ” then turns off.
STAR T
STO P
1716
DATA MANAGEMENT
DATA MANAGEMENT
Recall the Records
1. When the monitor is off, please press “MEM” button to show the recent record.
If the records are less than 3 groups, it will display the latest record instead.
( Take user 1 for example.)
2. Press “MEM” button
or “SET” button to get the record you want.
The date and time of the record
will be shown alternately.
CAUTION
The most recent record (1) is shown first. Each new measurement is assigned to the first (1) record. All other records are pushed back one digit (e.g., 2 becomes 3, and so on), and the last record (60) is dropped
from the list.
The current No. is No. 1. three records in total.
The corresponding date is 2019 year July 1st.
The corresponding time is 10:38.
Delete the Records
If you did not get the correct measurement, you can delete
results by following steps below.
A: Delete one record
1.Hold pressing “set” button for 3 seconds when the monitor is in the memory recall mode, the flash display “dEL one+User ID” will show.
2.Press and hold “Start/stop” button to confirm deleting and the monitor will display “dEL donE+USER ID” and then turn off.
Note: To exit out the delete mode press “Start/Stop” button shortly .
STAR T
STO P
1918
DATA MANAGEMENT
INFORMATION FOR USER
B: Delete all records
1.Hold pressing “MEM” button for 3 seconds when the monitor is in the memory recall mode, the flash display “dEL ALL+User ID” will show.
2.Press and hold “Start/stop” button to confirm deleting and the monitor will display “dEL donE+USER ID” and then turn off.
Note: To exit out the delete mode press “Start/Stop” button shortly .
3. If there is no record, the right display will show.
STAR T
STO P
Tips for Measurement
Measurements may be inaccurate if taken in the following circumstances.
Within 1 hour
after dinner or drinking
Within 20 minutes
after taking a bath
Immediate measurement after tea, coffee, smoking
When talking or moving your fingers
In a very cold environment
When you want to discharge urine
20 21
INFORMATION FOR USER
ABOUT BLOOD PRESSURE
Maintenance
Please calibrate the blood pressure monitor in specific institute once every two years to ensure the precise measurement. In order to get the best performance, please follow the instructions below for storage.
Put in a dry place and avoid the sunshine
Avoid intense shaking
and collisions
Using wet cloths to remove dirt
22
Avoid touching water,
clean it with a dry cloth in case.
Avoid dusty and unstable
temperature environment
Do not attempt to clean the reusable cuff with water and never immerse the cuff in water.
What are systolic pressure and diastolic pressure?
When ventricles contract and pump blood out of the heart, the blood pressure reaches its maximum value in the cycle, which is called systolic pressure. When the ventricles relax, the blood pressure reaches its minimum value in the cycle, which is called diastolic pressure.
Systolic
blood discharging
artery
press
Diastolic
blood entering vein
relax
What is the standard blood pressure classification?
The chart on the right is the standard blood pressure classifi­cation published by American
Heart Association (AHA).
This chart reflects blood pressure categories defined by American Heart Association.
Blood Pressure Category
Normal
Elevated
High Blood Pressure
(Hypertension) Stage 1
High Blood Pressure
(Hypertension) Stage 2
Hypertensive Crisis
(Consult your doctor immediately)
Systolic
mmHg (upper#)
less than 120
120-129
130-139
140 or higher
Higher than 180
Diastolic
mmHg (lower#)
and
less than 80
and less than 80
or
80-89
or
90 or higher
Higher than 120
and/or
CAUTION
Please consult a physician if your measuring result falls outside the range. Please note that only a physician can tell whether your blood pressure value has reached a dangerous point.
Irregular Heartbeat Detector
An irregular heartbeat is detected when a heartbeat rhythm varies while the device is measuring systolic pressure and diastolic pressure. During each measurement, blood pressure monitor will keep a record of all the pulse intervals and calculate the average value of them. If there are two or more pulse intervals , the difference between each interval and the average is more than the average value of ±25% , or there are four or more pulse intervals ,the difference between each interval and the average is more than the average value of ±15%, then the irregular heartbeat symbol will appear on the display with the measurement result.
CAUTION
The appearance of the IHB icon indicates that a pulse irregularity consistent with an irregular heart-beat was detected during measurement. Usually this is NOT a cause for concern. However, if the symbol appears often, we recommend you seek medical advice. Please note that the device does not replace a cardiac examination, but serves to detect pulse irregularities at an early stage.
23
ABOUT BLOOD PRESSURE
SPECIFICATIONS
AUTHORIZED COMPONENTS
TROUBLESHOOTING
Why does my blood pressure fluctuate throughout the day?
1. Individual blood pressure varies multiple times everyday. It is also affected by the way you tie your cuff and your measurement position, so please take the measurement under the same conditions.
2.If the person takes medicine, the
pressure will vary more.
3.Wait at least 3 minutes for another
measurement.
Why do I get a different blood pressure at home compared to the hospital?
The blood pressure is different even throughout the day due to weather, emotion, exercise etc, Also, there is the “white coat” effect, which means blood pressure usually increases in clinical settings.
Is the result the same if measuring on the right arm?
It is ok for both arms, but there will be some different results for different people. We suggest you measure the same arm every time.
What you need to pay attention to when you measure your blood pressure at home:
If the cuff is tied properly. If the cuff is too tight or too loose. If the cuff is tied on the upper arm. If you feel anxious. Taking 2-3 deep breaths before
beginning will be better for measuring.
Advice: Relax yourself for 4-5
minutes until you calm down.
This section includes a list of error messages and frequently asked questions for problems you may encounter with your blood pressure monitor. If the products not operating as you think it should, check here before arranging for servicing.
PROBLEM SYMPTOM CHECK THIS REMEDY
No power
Low batteries
Error message
Warning message
Display will not
light up.
Display is dim or show
E 01 shows
E 02 shows
E 03 shows
E 04 shows
EExx,shows on the display.
out shows
Batteries are exhausted.
Batteries are inserted incorrectly.
AC adaptor is inserted incorrectly.
Batteries are low.
The cuff is too tight or too loose.
The monitor detected motion, talking,or the pulse is too poor while measuring.
The measurement process does not detect the pulse signal.
The treatment of the measurement failed.
A calibration error occurred.
Out of measurement range
Replace with new batteries
Insert the batteries
correctly
Insert the AC adaptor
tightly
Replace with new batteries
Refasten the cuff and then measure again.
Relax for a moment and then measure again.
Loosen the clothing on the arm and then measure again.
Relax for a moment and then measure again.
Retake the measurement. If the problem persists, contact the retailer or our customer service department for further assistance.Refer to the warranty for contact information and return instructions.
Relax for a moment. Refasten the cuff and then measure again. If the problem persists, contact your physician.
24
25
SPECIFICATIONS
Battery powered mode:
6VDC 4*AAA batteries
Power supply
Display mode
Measurement mode
Measurement range
Accuracy
Normal working condition
Storage & transportation
condition
Measurement perimeter
of the upper arm
Net Weight
External dimensions
Attachment
Mode of operation
Device Classification
Degree of protection
Protection against ingress of water
Software Version
26 27
WARNING: No modification of this equipment is allowed.
AC adaptor powered mode:
(Please only use the recommended AC
adaptor model).
5V 1A
Digital LCD display V.A.60mm*74mm
Oscillographic testing mode
Rated cuff pressure:
0mmHg~299mmHg(0kPa ~ 39.9kPa)
Measurement pressure:
SYS: 60mmHg~230mmHg (8.0kPa~30.7kPa) DIA: 40mmHg~130mmHg (5.3kPa~17.3kPa) Pulse value: (40-199)beat/minute
Pressure:
5°C-40°C within±3mmHg(0.4kPa)
Pulse value:±5% A temperature range of :+5°C to +40°C
A relative humidity range of 15% to 90%,
non-condensing, but not requiring a water
vapour partial pressure greater than 50 hPa
An atmospheric pressure range of :
700 hPa to 1060 hPa
Temperature:-20°C to +60°C
A relative humidity range of ≤ 93%, non-condensing,
at a water vapour pressure up to 50hPa
About 22cm~32cm or 22cm~42cm
Approx.185g(Excluding the batteries)
Approx.93mm*130mm*32.5mm
4*AAA batteries,user manual, USB Cable,AC Adaptor
Continuous operation
Battery Powered Mode: Internally Powered ME Equipment AC Adaptor Powered Mode: Class II ME Equipment
Type BF applied part
IP21 It means the device could protected against solid foreign objects of 12.5mm and greater, and protect against vertically falling water drops.
A01
Authorized Components
1.please use the TRANSTEK
authorized adapter.
Adapter
BLJ06L050100U-U
Type: Input:100~240V,50~60Hz,0.2Amax Output:5V 1000mA
Contact Information
For more information about our products, please visit www.transtek.cn.you can get customer service, usual problems and customer download, transtek will serve you anytime.
Manufactured by: Company: Address:
Guangdong Transtek Medical Electronics Co., Ltd.
Guangdong Transtek Medical Electronics Co., Ltd. Zone B, No.105 ,Dongli Road, Torch Development District, Zhongshan,528437,Guangdong,China
AUTHORIZED COMPONENT
FCC STATEMENT
COMPLIED STANDARDS LIST
FCC Statement
FCC IDOU9TMB1872BS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Risk management
Labeling
User manual
General Requirements for Safety
Electromagnetic compatibility
Performance requirements
Clinical investigation
Usability
Software life-cycle processes
Bio-compatibility
EN ISO 14971:2012 / ISO 14971:2007 Medical devices -
Application of risk management to medical devices
EN ISO 15223-1:2016 / ISO 15223-1:2016 Medical devices. Symbols to be used with medical device labels, labelling and information to be supplied. Part 1 : General requirements
EN 1041:2008 Information supplied by the manufacturer of medical
devices
EN 60601-1:2006+A1:2013/ IEC 60601-1:2005+A1:2012 Medical
electrical equipment - Part 1: General requirements for basic safety and essential performance
EN 60601-1-11:2015/ IEC 60601-1-11:2015 Medical electrical
equipment - Part 1-11: General requirements for basic safety and essential performance - Collateral standard: Requirements for medical electrical equipment and medical electrical systems used in the home healthcare environment
EN 60601-1-2:2015/ IEC 60601-1-2:2014 Medical electrical
equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral standard: Electromagnetic disturbances - Requirements and tests
EN ISO 81060-1:2012 Non-invasive sphygmomanometers - Part 1:
Requirements and test methods for non-automated measurement type
EN 1060-3:1997+A2:2009 Non-invasive sphygmomanometers -
Part 3: Supplementary requirements for electro-mechanical blood pressure measuring systems
IEC 80601-2-30:2009+A1:2013 Medical electrical equipment- Part
2-30: Particular requirements for the basic safety and essential performance of automated non-invasive sphygmomanometers
EN 1060-4:2004 Non-invasive sphygmomanometers - Part 4: Test procedures to determine the overall system accuracy of automated non-invasive sphygmomanometers
ISO 81060-2:2013 Non-invasive sphygmomanometers - Part 2:
Clinical validation of automated measurement type
EN 60601-1-6:2010+A1:2015/IEC 60601-1-6:2010+A1:2013 Medical electrical equipment - Part 1-6: General requirements for basic safety and essential performance - Collateral standard: Usability
IEC 62366-1:2015 Medical devices - Part 1: Application of
usability engineering to medical devices
EN 62304:2006/AC: 2008 / IEC 62304: 2006+A1:2015 Medical
device software - Software life-cycle processes
ISO 10993-1:2009 Biological evaluation of medical devices- Part
1: Evaluation and testing within a risk management process
ISO 10993-5:2009 Biological evaluation of medical devices -
Part 5: Tests for in vitro cytotoxicity
ISO 10993-10:2010 Biological evaluation of medical devices -
Part 10: Tests for irritation and skin sensitization
28 29
Complied Standards List
EMC GUIDANCE EMC GUIDANCE
EMC Guidance
1)This product needs special precautions regarding EMC and needs to be
installed and put into service according to the EMC information provided, and this unit can be affected by portable and mobile RF communications equipment.
2)* Do not use a mobile phone or other devices that emit electromagnetic
fields, near the unit. This may result in incorrect operation of the unit.
3)Caution: This unit has been thoroughly tested and inspected to assure
proper performance and operation!
4)* Caution: This machine should not be used adjacent to or stacked with
other equipment and that if adjacent or stacked use is necessary, this machine should be observed to verify normal operation in the configuration in which it will be used.
Table 1
Guidance and manufacturer’s declaration – electromagnetic emissions
The device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment.
Emissions test Electromagnetic environment - guidance
RF emissions
CISPR 11
RF emissions
CISPR 11
Harmonic emissions
IEC 61000-3-2
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
Compliance
Group 1
Class B
Class A
Complies
The device uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.
The device is suitable for use in all establishments, other than domestic and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes.
Table 2
Guidance and manufacturer’s declaration – electromagnetic immunity
The device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment.
Immunity test
Electrostatic discharge (ESD) IEC 61000-4-2
Electrical fast transient/burst IEC 61000-4-4
Surge IEC61000-4-5
Voltage dips, short interruptions and voltage variations on power supply input lines
IEC 61000-4-11
Power frequency
(50Hz/60Hz) magnetic field
IEC 61000-4-8
NOTE UT is the a.c. mains voltage prior to application of the test level.
IEC 60601 test level
±8 kV contact ±15 kV air
power supply lines: ±2 kV
input/output lines: ±1 kV
line(s) to line(s): ±1 kV line(s) to earth: ±2 kV
100 kHz repetition frequency
0%UT; 0.5 cycle At 0°, 45°, 90°, 135°, 180°,225°,270° and 315° 0%U
T
; 1 cycle and 70%U
T
; 25/30 cycles Single phase: at 0° 0% U
T
; 300 cycle
30 A/m 50Hz/60Hz
Compliance level
±8 kV contact ±15 kV air
power supply lines: ±2 kV
line(s) to line(s): ±1 kV
100 kHz repetition frequency
0% U
T
; 0.5 cycle At 0°, 45°, 90°, 135°, 180°,225°,270° and 315° 0% U
T
; 1 cycle and 70% U
T
; 25/30 cycles Single phase: at 0° 0% U
T
;300 cycle
30 A/m 50Hz/60Hz
Electromagnetic environment - guidance
Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%.
Mains power quality should be that of a typical commercial or hospital environment.
Mains power quality should be that of a typical commercial or hospital environment.
Mains power quality should be that of a typical commercial or hospital environment.
Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment.
30 31
EMC GUIDANCE
EMC GUIDANCE
Table 3
Guidance and manufacturer’s declaration – electromagnetic immunity
The device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment.
Immunity test
Conducted RF IEC 61000-4-6
Radiated RF IEC 61000-4-3
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reflection from structures, objects and people.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular / cordless)
telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the device is used exceeds the applicable RF compliance level above, the device should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or relocating the device.
b
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3V/m.
IEC 60601 Test level
150 kHz to 80 MHz: 3 Vrms 6Vrms (in ISM and amateur
radio bands)
80% Am at 1kHz
10V/m, 80% Am at 1kHz
Compliance level
150 kHz to 80 MHz: 3 Vrms 6Vrms (in ISM and amateur
radio bands)
80% Am at 1kHz
10V/m, 80% Am at 1kHz
Electromagnetic environment - guidance
Portable and mobile RF communications equipment should be used no closer to any part of the device, including cables, than the recommended separation distance calculated from the equation appropriate for the frequency of the transmitter. Recommended separation distances: d=0.35 ;
P
d=1.2
P
80 MHz to 800 MHz: d=1.2
P
800 MHz to 2.7 GHz: d=2.3
P
where, P is the maximum output power rating of the
transmitter in watts (W)
according to the transmitter manufacturer, d is the recommended separation distance in
meters (m). Field
strengths from fixed RF transmitters, as determined by an electromagnetic site
a
survey, should be less than the compliance level in each frequency range. Interference may occur in the vicinity of equipment marked with the following symbol:
32
Table 4
Recommended separation distances between portable and mobile RF communications equipment and the device.
The device is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the device can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment
(transmittters) and the device as recommended below, according to the maximum output power of the
communications equipment.
Rated maximum output
power of transmitter
(W)
0.01
0.1
1
10
100
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
b
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.
Separation distance according to frequency of transmitter (m)
150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.7 GHz
=d
3.5
P
0.12 0.12
0.38
1.2
3.8
12
=d 1.2
0.38
1.2
3.8
12
P
0.23
0.73
2.3
7.3
23
2.3=d
P
33
EMC GUIDANCE
Table 5
Radiated RF IEC61000-4-3 (Test specifications for ENCLOSURE PORT IMMUNITY to RF wireless communicatio
ns equipment)
NOTE If necessary to achieve the IMMUNITY TEST LEVEL, the distance between the transmitting antenna and the ME EQUIPMENT or ME SYSTEM may be reduced to 1 m. The 1 m test distance is permitted by IEC 61000-4-3.
34
Guidance and manufacturer’s declaration - electromagnetic immunity
The device is intended for use in the electromagnetic environment specified below. The customer or the user of the device, should assure that it is used in such an environment.
Test
Band a)
Frequency
(MHz)
385
450 430-470
710 704-787
745
780
810
870
930
1720
1845
1970
5240
5500
5785
a) For some services, only the uplink frequencies are included. b) The carrier shall be modulated using a 50% duty cycle square wave signal. c) As an alternative to FM modulation, 50% pulse modulation at 18 Hz may be used because while it does
not represent actual modulation, it would be worst case.
The MANUFACTURER should consider reducing the minimum separation distance, based on RISK MANAGEMENT, and using higher IMMUNITY TEST LEVELS that are appropriate for the reduced minimum separation distance. Minimum separation distances for higher IMMUNITY TEST LEVELS shall be calculated using the following equation: E=
Where P is the maximum power in W, d is the minimum separation distance in m, and E is the IMMUNITY TEST LEVEL in V/m.
Service a) Modulation b) Modulation b)
(MHz)
380-390 TETRA
800-960
1700­1990
2570
5100­5800
400
GMRS 460 FRS 460
LTE Band 13, 17
GSM 800/900, TETRA 800, iDEN 820, CDMA 850, LTE Band 5
GSM 1800; CDMA 1900; GSM 1900; DECT; LTE Band 1, 3, 4,25; UMTS
Bluetooth, WLAN,
802.11 b/g/n, RFID 2450, LTE Band 7
WLAN
802.11 a/n
Pulse
modulation b)
18Hz
FM c) ± 5kHz
deviation 1kHz sine
Pulse
modulation b)
217Hz
Pulse
modulation b)
18Hz
Pulse
modulation b)
217Hz
Pulse
modulation b)
217 Hz
Pulse
modulation b)
217 Hz
(W)
1.8
2 0.3 28
0.2 0.3 9
2
2
2
0.2
Distance (m)
0.3 27
0.3 28
0.3 28
0.3 282450 2400-
0.3 9
IMMUNITY TEST LEVEL
(V/m)
Loading...